Stanje: rabljeno, Slot spindle 2 pcs. Number of milling units: 7 pcs. Spindle diameter: 50 mm Control: Weinig, PC-Nexus Weinig Unicontrol 12 with radial and axial NC spindles, VARIO table, and trimming carriage ..... Machine professionally dismantled and stored at our warehouse in 73447 Oberkochen. Video and photos were taken before dismantling. Technical data summary (additional accessories possibly included, please inquire) ..... Crosscut saw ..... > Electronic crosscut saw, horizontally infinitely adjustable > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.7 kW > Laser alignment light for identifying saw cuts > Axial adjustment range: 150 mm NC axis, electronically infinitely adjustable > Radial adjustment range: pneumatically controlled, 8 positions for e.g., edge rounding from above Rounding unit ..... Gedpfovu Hdyox Ah Djkc > Position: horizontal bottom > Motor power: 1.5 kW > Spindle diameter: 20 mm > Tool clamping length: 25 mm > Spindle speed: 9,000 rpm > Max. tool diameter: 130 mm > Axial adjustment mechanically linked with crosscut saw. > Radial adjustment: pneumatically operated on/off Electronic length stop ..... > Length: 4,500 mm 1st Tenoning and slotting spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment: 580 mm NC axis, infinitely adjustable > Spindle speed: 2,800 rpm > Max. tool diameter: 400 mm > Counter-support: the entire clamping length is counter-supported 2nd Tenoning and slotting spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment: 580 mm NC axis, infinitely adjustable > Spindle speed: 2,800 rpm > Max. tool diameter: 400 mm > Counter-support: the entire clamping length is counter-supported Transfer belt ..... For transferring parts to the longitudinal machining section, including part separation for doubles infeed to the longitudinal machining. 1st Profiling spindle (climb and counter rotation) ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment: 350 mm NC axis, infinitely adjustable > Radial adjustment: 80 mm NC axis, infinitely adjustable > Spindle speed: 6,000 rpm > Min. tool cutting circle: 140 mm > Max. tool cutting circle: 232 mm > 2 feed rollers opposite to spindle, axially pneumatically controlled, 8 positions > Table plate pneumatically controlled according to tool diameter 2nd Profiling spindle ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment: 350 mm NC axis, infinitely adjustable > Radial adjustment: 80 mm NC axis, infinitely adjustable > Spindle speed: 6,000 rpm ...

Stanje: novo, Število vreten: 6 kos Delovna širina: 250 mm Višina skobeljenja: 150 mm Dolžina poravnalne mize: 2500 mm Motor za podajanje: 4 kW Hitrost podajanja: 6-24 m/min Teža: 4770 kg Dimenzije (D/Š/V): 4722x1860x1776 mm Štiristranski skobeljni stroj Kuper SWT XL-6 v okenski izvedbi z elektronskim aksialnim in radialnim nastavljanjem vreten. Godpfx Aevnv Ubeh Dskc Masivno ogrodje stroja, nepopustljivo in z nizko vibracijo. Število vreten: 6 Delovna širina: 250 mm Delovna višina: 150 mm Dolžina poravnalne mize: 2500 mm Hitrost vreten: frekvenčno krmiljena 4.000 - 8.000 vrt/min Hitrost podajanja: 6-24 m/min Podroben opis najdete v pripeti PDF datoteki! (Tehnični podatki po navedbah proizvajalca - brez garancije!)

Leto izdelave: 2003, Stanje: rabljeno, Sistem 68 IV Število kompletov orodij: 29 kos Izvrtina: 50 mm Zlata okenska orodja IV68 les in les-alu prav tako vhodna za vhodna vrata IV 68 les Gkjdpswgwmbjfx Ah Dec Uporabljeno na Weinig Unicontrol 6. Na voljo so popolne risbe, glejte PDF. (Risbe vsebujejo tudi, zgolj informativno, orodja za letve, ki so bila uporabljena na stroju Weinig Unimat. Ta NISO vključena v obseg dobave.) (Tehnični podatki in risbe po navedbah proizvajalca – brez jamstva!)

Stanje: rabljeno, Working width: 3600 mm Working height: 2600 mm Number of pressing cylinders: 5 pcs. Loading dimensions (L x W x H): 4400 x 1150 x 2970 mm Weight: 3000 kg Schafberger + Sprödhuber Bavaria Frame Press ----- The machine will be overhauled by us prior to delivery With automatic pressing cycle + manual control For corner joints with tenon and mortise connections CE-compliant version Base machine features a reinforced frame-welded construction with thick-walled special hollow profiles. Guide rails of the pressure beams for the press corners are manufactured for low wear. Quick and easy manual width adjustment via ball-bearing mounted carriage, fixation in perforated grid. Height adjustment and pressing with long-stroke cylinders in a single operation cycle. Right-side press corners feature integrated horizontal cylinders, so no vertical positioning of the horizontal pressing cylinders is necessary, thus preventing cylinder collisions. The bottom abutments can be set to multiple positions for optimal workpiece insertion height. 3 vertical double-acting pressing cylinders, stroke adapted to working height, 2 horizontal double-acting pressing cylinders Abutment and pressure plate depth: 80 mm Working dimensions: Length x Height = approx. 3,600 mm x 2,600 mm Space requirement/loading dimensions: approx. 4,400 mm x 1,150 mm x 2,970 mm (LxWxH) Option: ALWA pressing aids for angled windows (Technical specifications according to manufacturer – no guarantee! Illustrations may differ from the original, prices net, plus VAT (domestic).) Gkodpfxsw T Un Uo Ah Doc

Stanje: novo, Leto izdelave: 2025, Number of motors: 2 units Working length: 3000 mm Control system: Yes/CNC Loading dimensions (L x W x H): 4000 x 1500 x 1500 mm Weight: 800 kg HECHT Double Mitre Saw Exenso DS350E - 3000 mm For wooden glazing beads, muntins, profile strips, aluminium strips, etc. Pos. 1.1 Item no. 942.5103 1 unit HECHT Exenso DS350E - Working length: 3000 mm - Swivel range: 22.5° (internal) to 135° (external) - Movable right head - Saw blade holder Ø 350 mm - Incl. 1 pc. centre support - Pneumatic clamping of the units - Positioning control Exenso DS3 with 15" touch panel display in a dust-protected monitor housing - 3-axis control: 1 longitudinal and 2 swivel axes - Manual input of cutting data - Processing of data from a cutting list (data set as specified) - Processing of measuring stick data (radio caliper GMF) - Ethernet connection 10/100 (TCP/IP) - USB interface - Incl. control cabinet, motor and software licences Pos. 1.2 Item no. 723.0121 Gjdpovzt D Tjfx Ah Dekc 2 pcs. DS saw blade wood Bevel/Bevel/Flat tooth - Positive Pos. 1.3 Item no. 942.5236 2 sets DS combined workpiece clamping Combined clamping consisting of: Pneumatic swing clamp for clamping material from above (free access to the work table) Horizontal pneumatic clamp – anti-rotation clamping cylinder with pressure piece Clamps can be selected individually via the saw's control system Clamping sequence can also be set via control system Includes safety pre-clamping pressure Scope for 2 sets: - 2 pcs (left/right) vertical swing clamps - 2 pcs (left/right) horizontal clamps Pos. 1.4 Item no. 942.5997 DS feed unit pneumatic Pos. 1.5 Item no. 945.2007 DS350 packaging (transport frame) ----- Total price for this configuration ex-works – on request! ----- ALTERNATIVE options, prices on request! ----- For horizontal clamping of offcuts when working with square-cut glazing beads instead of 2nd set Pos. 1.3 943.5236 DS combined clamping! Pos. 2.1 Item no. 942.5201 ES/DS front workpiece clamping - 2 pcs anti-rotation clamping cylinders - 2 pcs cylinder holder with clamping lever ----- For rebated glazing bead, instead of standard plates without groove: Pos. 2.2 Item no. 942.5241 DS350 grooved table supports to customer sample Mounted table supports are milled according to customer drawing Please send us all profile drawings to be cut (pdf, dxf and physical sample) ----- If, for example, aluminium is also to be cut: Pos. 2.3 Item no. 942.5203 DS feed unit hydropneumatic (instead of pneumatic feed cylinder) ----- OPTIONAL accessories, subject to surcharge upon request: ----- Pos. 2.4 Item no. 942.5237 DS Software "Overlength" (subsequent steps must be confirmed) Sequence control incl. hardware. After entering a cutting dimension > max. cutting length of the machine, the cutting is carried out cyclically (left unit cuts, right unit moves material and cuts to size). ----- Pos. 2.5 Item no. 944.1023 GMF caliper 3000 mm complete set (1500 mm plus 1500 mm extension) Incl...

Stanje: rabljeno, Slotting spindle 2 pcs. Number of milling units: 7 pcs. Spindle diameter: 50 mm CNC control, Weinig PC-Nexus Weinig Uncontrol 12 with radial and axial NC spindles as well as VARIO table ..... Machine is already professionally dismantled and stored in 73447 Oberkochen Technical Data Summary (for any additionally included accessories, please inquire) ..... Cross-cut saw ..... > Cross-cut saw electronic, horizontally adjustable steplessly > Number of tools: 1 pc. > Spindle speed: 3000-6000 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm Gkodewmgfyspfx Ah Dsc > Motor power: 3.7 kW > Laser guide for cut recognition > Axial adjustment range 150 mm NC axis, electronically stepless > Radial adjustment range pneumatically adjustable in 8 positions e.g. for edge rounding from above Rounding unit ..... > Position: horizontal below > Axial adjustment range together with cross-cut saw. Electronic length stop ..... > Length: 4500 mm 1. Tenoning and slotting spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment range: 580 mm NC axis, stepless > Spindle speed: 2,800-4,000 rpm > Tool diameter: 380-400 mm > Outfeed counter, full clamping length countered 2. Tenoning and slotting spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment range: 580 mm NC axis, stepless > Spindle speed: 2,800-4,000 rpm > Tool diameter: 380-400 mm > Outfeed counter, full clamping length countered Transfer conveyor ..... For transferring parts to the longitudinal processing, including Double part separation before entry into longitudinal processing. 1. Profiling spindle (climb and conventional milling) ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment range 350 mm NC axis, stepless > Radial adjustment range 80 mm NC axis, stepless > Spindle speed: 6000 rpm > Tool diameter min.: 140 mm > Tool diameter max.: 232 mm 2. Profiling spindle ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment range 350 mm NC axis, stepless > Radial adjustment range 80 mm NC axis, stepless > Spindle speed: 6000 rpm > Tool diameter min.: 140 mm > Tool diameter max.: 232 mm 3. Profile milling unit (grooving device from above) ..... > Position: horizontal above > Motor power: 3.0 kW > Spindle diameter: 40 mm > Tool clamping length: 40 mm > Axial adjustment range 30 mm NC axis, stepless > Radial adjustment range 125 mm NC axis, stepless

Stanje: rabljeno, Keyway Spindle 1 pc. Number of Milling Units: 5 pcs. Spindle Diameter: 50 mm Control System: Weinig, PC-Nexus #2774 Weinig Unicontrol 6 with NC Spindles Machine is cleaned and fully inspected prior to delivery Technical Data Summary (Please enquire about any additional included accessories) Pos. 1: Cross-Cut Saw ----- > Number of Tools: 1 pc. > Spindle Speed: 2,800 rpm > Spindle Diameter: 40 mm > Max. Tool Diameter: 400 mm > Motor Power: 3 kW > Radial Adjustment pneumatically controlled across 8 positions, e.g., for top edge rounding > Laser Guidance for cutting section detection Pos. 2: Rounding Unit, Horizontal Lower ----- > Position: horizontal, lower > Motor Power: 1.5 kW > Spindle Diameter: 20 mm > Clamping Length: 25 mm > Spindle Speed: 9,000 rpm > Max. Cutting Circle: 130 mm > Axial Adjustment mechanically linked with cross-cut saw > Radial Adjustment pneumatically controlled, on/off NC-Controlled Length Stop ----- > Length: 3,500 mm > Electronic length stop Pos. 3: Tenoning and Keyway Spindle ----- > Number of Tools: variable, stepless adjustment, NC controlled > Tool Clamping Length: 320 mm > Vertical Spindle Stroke: variable, 254 mm, stepless, NC controlled > Spindle Speed: 3,500 rpm > Max. Cutting Circle: 320 mm > Spindle Diameter: 50 mm > Max. Tool Diameter: 320 mm > Motor Power: 11 kW Pos. 4: 1st Profiling Spindle (Climb and Conventional Milling) Godpfjvu Hghjx Ah Djkc ----- > Position: vertical, right > Number of Tools: 1 pc. > Tool Clamping Length: 120 mm > Spindle Speed: 6,000 rpm > Spindle Diameter: 50 mm > Max. Cutting Circle: 232 mm > Motor Power: 7.5 kW Pos. 5: 2nd Profiling Spindle ----- > Position: vertical, right > Number of Tools: variable, stepless adjustment, NC controlled > Tool Clamping Length: 320 mm > Vertical Spindle Stroke: variable, 254 mm, stepless, NC controlled > Spindle Speed: 6,000 rpm > Spindle Diameter: 50 mm > Max. Cutting Circle: 232 mm > Motor Power: 11 kW 2 Feed Rollers opposite the spindle, axially pneumatically controlled, 2 positions Sash Bar Guide consisting of: Guide rail at the stop (climb milling section), Sash bar support rail from above in the area of the vertical right profile milling unit and profiling spindle. Pos. 6: Profiling Milling Unit, Horizontal Upper ----- > Clamping Length: 40 mm > Spindle Diameter: 40 mm > Motor Power: 3.0 kW > Speed: 9,000 rpm > Max. Cutting Circle: 130 mm > Axial Adjustment: 30 mm, 8 positions > Radial Adjustment: 125 mm, 8 positions Pos. 7: 3rd Profiling Spindle (Fitting Spindle) ----- > Position: vertical, right > Tool Clamping Length: 160 mm > Axial Adjustment: 115 mm, 8 positions > Radial Adjustment: 110 mm, 8-position turret > Spindle Speed: 5,850 rpm > Spindle Diameter: 40 mm > Max. Cutting Circle: 210 mm > Motor Power: 3.0 kW Pos. 8: Profile Milling/Grooving Unit, Bottom ----- > Motor Power: 3.0 kW > Tool Clamping Length: 125 mm > ...

Stanje: rabljeno, Number of drilling motors: 1 unit Corner fitting drilling: 1=yes, 0=no 1 yes Olive drilling: 1=yes, 0=no 1 yes 1 HESS Fitting Drilling Station for Corner Fittings and Olives This HESS drilling station offers extensive drilling technology at a low price for craftsmen. A complete station for drilling both corner fittings and olives, equipped with all essential features, including: - 2 clamping cylinders - Drilling depth sensing - Effective extraction system - Stop systems for corner fitting and olive drilling - Drill head with quick-change chuck - Adjustable drill feed speed - Automatic program sequence This means technology for perfect work: only one machine with a single drilling unit and one drill head for two operations. System Description: - Base frame as panel for frame and sash up to 100 mm - Drilling unit centrally positioned, height-adjustable manually via threaded spindle - Drill hole position and depth preset for the specific fitting type, adjustable via stop system when changing types - Drill feed speed steplessly adjustable via throttle valve - Direct extraction - Electropneumatic control system with automatic program sequence for: - Clamping the workpiece - Start drilling motor Gksdpfxjvu Hgzj Ah Doc - Move drilling aggregate forward - Drilling - Return drilling aggregate - Stop drilling motor - Release workpiece clamping - Fixed stop systems Standard Equipment / Technical Data: - Sturdy base frame as panel, precise support made of wear-resistant and dimensionally stable plastic, for frames and sashes up to 100 mm thick - Corner fitting and olive drilling possible with one machine and one drilling unit - Simple and convenient vertical operation, easy handling, no templates needed - Minimal setup time for secure workpiece positioning - Guaranteed precise and accurate boreholes - 2 clamping cylinders for secure fixation of sash or frame, adjustable for different wood thicknesses - Lateral rebate stop for corner fittings - Ergonomically arranged stop system for olive drilling, with 14 swiveling stops and additional color coding - Fixed stop system for hole height adjustment when switching from corner fitting to olive - Automatic drilling depth sensing for both corner fitting and olive - Drilling unit with quick-change chuck for different tools (corner fitting and olive). Tool change in no time - Automatic program sequence - Clean operation due to effective extraction - Space saving and mobile thanks to steering/brake castors Electrical equipment according to VDE regulations. Electrical connection: 0.55 kW, 400 V, 50 Hz Pneumatic connection: R 3/8", 4-8 bar Extraction port: 1 x 100 mm diameter Extraction speed: 25 m/sec Required space: Width: 2600 mm Height: 1250 mm Depth: 800 mm Support height: 300 mm Paint finish: RAL 7030 stone grey with RAL 1018 zinc yellow 1 drill set with 1 x 25 mm drill and 2 x 10 mm drills additional 1 x 34 mm diameter drill (Technical data according to manufacturer's information – subject to change without notice!)

Stanje: rabljeno, Number of spindles: 4 pcs Number of tool sets: 11 pcs Spindle diameter: 50,40 mm Spindle length: 285,125 mm Gksdpfx Ahevnv Uus Dec Length: 4000 mm Width: 2000 mm Height: 2200 mm Weinig Univar 10/3 Profile Reworking Machine ----- For re-profiling of windows, doors, and similar items featuring asymmetrical perimeter profiles. Suitable for timber thicknesses from 68 to 92 mm. Processing time per frame re-profiling for a medium size (1.20 x 1.20 m) – approx. 2 min. Available tool positions can be selected via the operator control panel. The machine is equipped with three hydraulically controlled right-side precision lifting spindles, designed to accommodate three tool sets, each spindle providing 2 x 95 mm vertical spindle stroke. The spindle stroke is performed in a U-motion, enabling minimal opening in the milling fence when processing short parts. Spindle stroke can be finely adjusted horizontally for both tool positions from the operator side. Centralized lubrication for spindle units. For tear-free re-profiling of window sashes or frames and doors, the first spindle can be selected for clockwise or counterclockwise rotation. At each of the last 100 mm at the end of a frame, this spindle with the corresponding climb-cutting tool plunges into the passing timber. This prevents tear-out caused by the following counter-rotating milling spindle. The first seven transport rollers can be lifted via foot pedal, shortening the throughput time. An additional support rail permits re-profiling of large-format frames as well. Continuous, chainless rubber roller feed with extremely short roller spacing. Feed beam height is electronically measured and displayed. Electrical design according to VDE standards. Machine is supplied with operation tools, but without machining tools. Technical data: Working width min. 40 mm Working height min. 30 mm, max. 100 mm 1st Profile Spindle (climb and counter-rotation) ----- Spindle motor power: 11.0 kW Spindle speed: 6000 rpm Spindle diameter: 50 mm Clamping length: 285 mm Tool base circle: 112 - 140 mm Max. tool diameter: 232 mm Vertical spindle stroke: 2 x 95 mm for 3 tools Home position below table: 10 mm (adjustable up to 20 mm) Horizontal spindle stroke: 80 mm With automatic climb-cutting plunge mechanism 2nd Profile Spindle ----- Spindle motor power: 11.0 kW Spindle speed: 6000 rpm Spindle diameter: 50 mm Clamping length: 285 mm Tool base circle: 112 - 140 mm Max. tool diameter: 232 mm Vertical spindle stroke: 2 x 95 mm for 3 tools Home position below table: 10 mm (adjustable up to 20 mm) Horizontal spindle stroke: 80 mm 3rd Profile Spindle ----- Spindle motor power: 11.0 kW Spindle speed: 6000 rpm Spindle diameter: 50 mm Clamping length: 285 mm Tool base circle: 112 - 140 mm Max. tool diameter: 232 mm Vertical spindle stroke: 2 x 95 mm for 3 tools Home position below table: 10 mm (adjustable up to 20 mm) Horizontal spindle stroke: 80 mm 4th Profile Spindle – Fitting (hardware) unit, right ----- For machining the hardware groove during the re-profiling pass or for grooving along the longitudinal profile. Pneumatic horizontal movement with selector switch at the operator control panel. Motor power: 2.2 kW Speed: 6,000 rpm Spindle diameter: 40 mm Clamping height: 125 mm (for 2 tools) Tool cutting circle min. 140 mm, max. 180 mm Feed motor power: 1.1 kW Feed speed...

Stanje: rabljeno, Working width: 3550 mm Working height: 2250 mm Number of pressure cylinders: 5 pcs Loading dimensions (L x W x H): 4500 x 900 x 2600 mm Hess Speedy Frame Press Gkodpfx Ahjvn U Ruo Dsc ----- Machine has been function-tested Insert size / Max. pressing length: 3,550 mm Insert size / Max. pressing height: 2,250 mm Sliding carriage for width adjustment with locking at 50 mm intervals Double hole raster system Electric height adjustment of long-stroke cylinders (hydraulic) Support plate insertion height preselectable in 4 positions 3 vertical pressure cylinders, stroke 1000 mm Pressing force per cylinder: 2000 kN / 20,000 N 2 horizontal pressure cylinders, stroke 80 mm Pressing force per cylinder: 1250 kN / 12,500 N Pressure plate depth: 100 mm / width: 140 mm Raster cylinder locking / support: 50 mm Central pressure beam with shut-off valve End pressure cut-off and re-pressing control Control and pressing cycle in push-button mode Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection: 2.2 kW / 400V Control system for angled window gluing 2 pivoting pressure plates at 45 degrees Machine dimensions (W=4500 mm, D=900 mm, H=2600 mm) Weight approx. 1800 kg Original images. Video not original, shows identical model (Technical data according to manufacturer – No liability assumed!)

Stanje: rabljeno, Leto izdelave: 2018, Število motorjev: 1 kos Delovna dolžina: 2500 mm Krmiljenje: ne Enostranska žaga za zasteklitvene letve Hecht ES 350 ----- Zasuk pnevmatsko proti fiksnim omejevalcem. 45º/90º/135º s pnevmatskim pomikom žaginega lista pnevmatsko nihanje preko ročnega omejevalca z nogo stroja, pnevmatska pritrditev Žagin list HM 350 x 3,0/2,2/30 Z 100 Mere stojala za žago: dolžina 700 mm, globina 1.600 mm, višina 1.500 mm Dotikalni omejevalec 1,5 m Oporna površina 1,5 m z nosilcem Dotikalni omejevalec 3 m Podaljšek oporne površine z 1,5 m na 3 m z nosilcem Gksdpfxjvpr N Re Ah Dsc Vložki v mizo z utori za prekrivne zasteklitvene letve HECHT ASB ročni dolžinski omejevalec z digitalnim prikazovalnikom, 2500 mm Z odsesovalno napravo (Tehnični podatki po navedbah proizvajalca – brez jamstva!)

Stanje: rabljeno, Number of sanding units: 4 pcs Sanding width: 190 mm Max. sanding height: 4–180 mm Weight: 4200 kg Hess Expert 4-Belt Single-Piece Wood Sander Ø Sanding from below and above Ø Each with 2 staggered sanding units (top and bottom) Ø Sanding units (top and bottom) connected in series according to the precision planing principle Ø Pre-sanding with coarse grit (calibration) Ø Fine sanding with fine grit (finish) Ø Central motorized height adjustment of the lower sanding units Ø Central motorized and synchronous height adjustment of the complete upper sanding and brushing units, including the upper transport units Ø Oscillating belt use (during the sanding process) Ø Absolute power transmission via 5.5 kW motors and large dimensioned drive drums Ø Oxide-ceramic sanding shoe for - precise surface geometry - no readjustment required - permanent dimensional accuracy - completely maintenance- and wear-free Basic structure: Stable, heavy welded construction made of thick-walled rectangular profiles with additional, statically calculated stiffeners for optimal vibration damping. Staggered sanding units with large-diameter belt drive drums for slip-free belt tracking. Dual-point extraction for direct and airborne dust with sealing brushes and integrated sanding belt air-blast device to extend belt service life. Sanding units in robust steel plate construction serve as the base for vibration-damped, smooth belt operation. Absolutely backlash-free guidance by ball-type linear sets made of hardened and ground shafts. Height adjustment of the sanding units via hardened and ground special linear guides and preloaded carriage units. Long-term precision is ensured by dust and dirt protection of the ball linear sets and carriage units. Large-diameter presanding rollers as contact drums. Contact drums and sanding shoes are balanced relative to the sanding belt grit stress. The oversized drive drums guarantee the full power transmission of the 5.5 kW sanding motors to the sanding belt, ensuring slip-free, stable running and optimal heat dissipation, allowing for maximum material removal. Automatic machine stop in the event of belt breakage. Optical display at the control panel and via signal light on the machine. Sanding shoes for finishing are entirely maintenance- and wear-free, made from oxide-ceramic with optimal heat dissipation. Belt tensioning is provided by appropriately sized compression springs. Belt release for belt change is done via a pneumatic unit for gentle and distortion-free installation of new belts. The upper sanding and brush units are centrally and motor-driven height adjustable, with digital display at the control panel for motorized sanding thickness adjustment. Brush and finishing device, for improved surface finish, is integrated into the base machine. Two vertically arranged special brush rollers, 150 mm Ø, run in the direction of feed. Separate height adjustment of the brush rollers on precision carriage guides allows adjustment for wear compensation. An additional transport roller is provided for ejecting or further transporting the workpiece from the sanding machine, linked to the conveyor belt. Wood guiding at the infeed area for hard, double-sided... Gkodpfx Aot Tqy Esh Dsc

Stanje: rabljeno, Crosscut Saw 3 kW Spindle Diameter: 50 mm Spindle Length: 300 mm Number of Tool Sets: Variable Control: CNC Dimensions (L x W x H): 2500 x 1700 x 2100 mm Weight: 1700 kg HABERKORN - Groove Cutting Machine FZS-2 Electronic with Continuously Adjustable Grooving Spindles and Automatic Roller Table ----- Crosscut Saw ----- Spindle Arrangement: Top Three-Phase Motor: 3 kW Spindle Diameter: 30 mm Speed: 2800 rpm Saw Blade Diameter: 400 mm * Automatic brake with speed monitoring * Infinitely variable saw positioning with Siko display * Safety and extraction hood with 100 mm extraction port 2 Grooving Spindles, 50 mm Diameter ----- Power: 2 x 7.5 kW Speed: 4200 rpm Spindle Diameter: 50 mm Tool Diameter: approx. 360 mm Usable Length: 300 mm * Both grooving spindles positionable via ball screw * Fully programmable, 19 programs, display with function keys * Safety and extraction hood with 180 mm extraction port * Automatic brake with speed monitoring Gjdpswgwlkefx Ah Dokc Swing Table ----- * Swivel range: +/- 65° * Automatically changing backstop (programmable) * Pneumatic clamp * High-precision electronic angle display * Automatic length compensation * Backstop positioned in the cutting plane at every angle setting Special Equipment ----- Continuously variable roller table feed Laser for workpiece positioning Manual length stop LA 2000 Length: 2500 mm Extraction Port Diameter: 2 x 180 mm for grooving spindles 1 x 100 mm for crosscut saw ----- Price of the above-mentioned machine on request! ----- Images show an identical model. Original photos currently unavailable. (Technical data according to manufacturer – subject to change!) All prices stated are net. VAT to be added as per statutory rate.

Stanje: rabljeno, Number of sanding units: 2 pcs. Sanding width: 190 mm Max. sanding height: 4–180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Machine will be inspected! Manufacturer's description: ----- Compact design constructed according to modern requirements. Quiet and vibration-free operation due to a torsion-resistant, stable machine housing and special insulation. Safety features comply with EC Machinery Directive and are certified as "dust-tested." Offset sanding units with large-diameter tension rollers for effective heat dissipation and stable sanding belt guidance. Sanding units feature forced sanding belt oscillation. Two-point sanding dust extraction directly at the sanding drum. Ambient dust extraction at the large tension rollers. Integrated sanding belt air blow-off system for increased belt lifetime. Integrated brush and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized sanding thickness adjustment of the upper unit via precision lead screws and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and sanding shoe optimally balanced to sanding belt grain load. Hardened and ground sanding rollers. Maintenance- and wear-free oxide-ceramic sanding shoes (DBGM) with excellent sliding properties, effective heat dissipation, and high dimensional accuracy. Sanding belt tension via pneumatic cylinder. Sanding belt change via pneumatically controlled belt release. Adjustable belt tracking during belt changes. Electropneumatic air pressure monitoring with visual fault indicator. Automatic machine stop in case of belt breakage and entry safety system with integrated wood thickness control. Visual fault indicators on the control panel. Feed mechanism and proven, calibrated slip- and traction-proof conveyor belts on precision-ground tables and spring-loaded pressure rollers. Cardan shaft drive for uniform wood feed. Continuously variable feed speed. Chip removal adjustment below via precision lead screw with scale ring indicator (resolution 0.1 mm). Gjdpfx Aev D Rg Djh Djkc Ergonomically arranged control and adjustment elements on the machine front: sanding unit and brushing device (top), sanding unit and brushing device (bottom), workpiece transport device, sanding thickness adjustment, operation indicator, fault indicator. Built-in control and operation unit in the machine housing with lockable main switch. All motors electrically protected against overload. Technical data: ----- Sanding belt speed: 24 m/sec Sanding width: 190 mm Sanding thickness: 4–180 mm Shortest workpiece length: 300 mm Feed speed: steplessly adjustable 5–25 m/min Sanding belt size: 200 mm wide x 1600 mm long Electrical connection: 400 V, 3/N PE, 50 Hz Sanding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000–2500 m³/h at 20–25 m/sec Extraction connection: 2 x 160 mm diameter on top of the machine housing

Stanje: rabljeno, Slotting spindle 1 pc Number of milling units: 4 pcs Spindle diameter: 50 mm Control: Weinig, PC-Nexus 4x Weinig Unicontrol 10 CNC – Spindles CNC controlled both radially and axially ----- Machine factory-refurbished by Weinig in 2024. As part of this, the control system was upgraded to Siemens S7-677C with new “Touch” membrane panel. Equipped with the following machining units: Cross-cut saw ----- with laser alignment light, motor power 3 kW, spindle diameter 40 mm, spindle speed 3,000 rpm axial adjustment via NC axis radial adjustment pneumatic, 8 positions for edge rounding from above Edge rounding unit from below ----- axial adjustment synchronized with cross-cut saw tenoning and slotting spindle ----- motor power 15 kW spindle diameter 50 mm spindle speed 2,925 rpm minimum tool cutting circle: 380 mm, maximum: 400 mm tool clamping length: 640 mm axial adjustment via CNC axis axial adjustment range: 580 mm adjustment speed: 100 mm/sec 1st profiling spindle (climb & conventional milling) ----- motor power 11 kW spindle diameter 50 mm spindle speed 6,000 rpm tool clamping length: 400 mm with counter bearing axial and radial adjustment via CNC axis 2nd profiling spindle ----- motor power 11 kW spindle diameter 50 mm spindle speed 6,000 rpm tool clamping length: 400 mm with counter bearing axial and radial adjustment via CNC axis Horizontal profiling unit, upper position ----- motor power 3 kW spindle diameter 40 mm spindle speed 9,000 rpm pneumatic adjustment to 8 positions, axial and radial Vertical profiling unit, right at machine outfeed ----- motor power 3 kW spindle diameter 40 mm spindle speed 5,850 rpm pneumatic adjustment to 8 positions, axial and radial Further accessories: ----- CNC-controlled length stop, mounted on slotting table for lengths up to 3,500 mm, including programmable cross-cut saw integrated in the control Studio window device, +/-60° swiveling on both sides Double-part bundle with automatic separation and transfer Climb-milling device with automatic window operation for rebating Rebating carriage for handling narrow sash widths Air-conditioning unit in control cabinet PC control NEXUS Automatic turning system Gksdow Im H Sopfx Ah Djc Lamella conveyor, including return conveyor belt for returning workpieces to the operator (Technical data as per manufacturer – no guarantee).

Stanje: rabljeno, Leto izdelave: 2013, Premer izvrtine, mm Število vodoravnih vrtalnih glav, kos Število navpičnih vrtalnih glav, kos 2 kosa Götzinger vrtalno-rezalnega centra ----- Prodaja po naročilu stranke! 2 enaki stroji: En stroj uporabljen za "leve" dele, drugi za "desne" dele. Stroje je možno uporabljati tudi posamezno. Stroje je upravljala programska oprema za izdelavo oken, lahko pa jih upravljate tudi preko lastne programske opreme stroja. Oba stroja imata enako opremo: - Vrtalni agregat levo in desno za čelne izvrtine. - 3 agregate za vrtanje in rezkanje vzdolžnih obdelav. Gkjdpfx Asv N N Speh Dec - Obdelovanci se vložijo le enkrat, nosilec agregata izvede različne operacije. Namestitvena dolžina posameznega stroja cca 6 m. Možna posamezna prodaja: Cena na stroj: 10.000 EUR Več informacij v priloženih PDF-jih.

Stanje: rabljeno, Working width: 3550 mm Working height: 2250 mm Number of hydraulic cylinders: 5 pcs Loading dimensions (L x W x H): 4500 x 900 x 2600 mm Hess Speedy Frame Press ----- Press overhauled Max. insert/pressing length: 3,550 mm Max. insert/pressing height: 2,250 mm Sliding carriage for width adjustment with 50-mm indexed locking (double-hole grid system) Electric height adjustment for long-stroke cylinders (hydraulic) Support plate insertion height preselectable in 4 positions 3 vertical pressure cylinders, stroke: 1000 mm Pressure force per cylinder: 2,000 kN / 20,000 N 2 horizontal pressure cylinders, stroke: 80 mm Pressure force per cylinder: 1,250 kN / 12,500 N Pressure plate depth: 100 mm, width: 140 mm Cylinder and support plate grid: 50 mm Central pressure beam with shut-off valve End pressure shut-off and post-pressure regulation Control and pressing operation in pulse button mode Adjustable pressing pressure: min. 25 – max. 160 bar Electrical connection: 2.2 kW / 400 V Control system for angled window gluing 2 pivoting pressure plates, 45 degrees Gkjdovn U Rnjpfx Ah Djc Machine dimensions (W x D x H): 4500 x 900 x 2600 mm Weight: approx. 1,800 kg Photo and video are not original, but show an identical model (Technical specifications according to manufacturer – no guarantee!)

Stanje: rabljeno, Slot spindle 1 pc. Number of milling units 0 pcs. Spindle diameter 40 mm Small window production line consisting of: ----- 1) Haberkorn FZS1 slot mortising machine 2) Okoma SF3F spindle moulder 3) Oertli tooling set for Haberkorn and Okoma machines Timber window set IV 68/78/88 and one set wood-aluminium windows IV 68/78, year of manufacture 2011 4) Götzinger OBM Plus corner and handle drilling machine, hardware Maco MultiMatic ----- Technical manufacturer description: - Haberkorn FZS1 slot mortising machine with automatic feed - Continuously variable height adjustment D 40 mm Crosscut saw: - Spindle arrangement: top - Three-phase motor: 3 kW - Spindle diameter: 30 mm - Speed: 2800 rpm - Saw blade diameter: 400 mm - Automatic brake with speed monitoring - Horizontal positioning pneumatic, manual adjustment - Safety and extraction hood with extraction port diameter: 100 mm Slot spindle D 40 mm: - Power: 7.5 kW - Speed: 4200 rpm - Usable length: 252 mm - Max. tool diameter: 340 mm - 220 mm stroke, infinitely variable height adjustment via precision ball screw - Safety and extraction hood with extraction port diameter: 180 mm - Automatic brake with speed monitoring Tilting table: - Swivel range +/- 65 degrees - Automatically changing backing wood (programmable) - Pneumatic clamp - High-precision electronic degree display - Automatic length compensation - Backing wood always in the cutting plane regardless of angle setting Special features: - Laser for workpiece positioning - Saw position pneumatic - Length stop LA 2500 mm + 1850 mm extension ----- 2) Okoma SF3F spindle moulder with lifting spindle, 3 tools - Extraction connection 2 x 120 mm - Spindle length 270 mm - Adjustable fence with fine adjustment and revolver head - Triple lift, max. stroke height 90 mm - Glazing bar separation saw with safety and extraction hood, 80 mm diameter - 8-roll power feed unit with stand and hold-down arm, required for insulation for glazing bar separation saw - Pneumatically actuated notching device for edge gearing, speed 6000 rpm - 2 x 3 kW motor - Tool holder diameter 30 mm ----- 3) Oertli tooling for Haberkorn and Okoma machines - 1 set timber windows IV 68/78/88 - 1 set timber-aluminium windows IV 68/78 ----- Gsdexa Hi Nopfx Ah Dokc 4) Götzinger OBM Plus corner and handle drilling machine - Corner and scissor hinge & handle drilling - Vertical drilling unit with: - Quick-change drill head system - Pneumatic feed via foot pedal - 1x handle drilling head 24 mm - 1x double head corner hinge - Hardware Maco MultiMatic - 1x adjustable folding stop left with 6 positions - 1x adjustable folding stop right with 6 positions - 1x machine stand complete with storage shelf - 220/400 V, 60 Hz, 1.3 kW - 1 x roller conveyor approx. 1 m long with 2 rollers - 1 x roller conveyor approx. 1.5 m long with 3 rollers ----- Price for the above-mentioned machines on request! Plus packing and shipping ----- (Technical specifications according to manufacturer - subject to change!) All prices quoted are net, plus VAT.

Stanje: novo, Working width: 4500 mm Working height: 3000 mm Number of press cylinders: 6 pcs. Dimensions (LxWxH): 5500 x 1400 x 3550 mm Weight: 3000 kg S&S Frame Press Bavaria 2000 L ----- With automatic pressing cycle and manual operation for corner joints with tenons & mortises and dowel connections / mortised tenons, switchable via selector switch on the control cabinet. Basic equipment allows optional use of counter profiles, if the sash is folded on the loose part. CE-compliant version Base machine in extra-strong, welded frame construction, with thick-walled special hollow profiles. Guideways for pressure beams at the press corners are made with wear-resistant machining. Fast, smooth manual width adjustment via ball-bearing carriage, fixation in 50 mm hole grid, optionally motorized width adjustment with hydraulic clamping (at extra cost). Height adjustment and pressing performed in a single cycle by long-stroke cylinders. Right-side press corners with integrated horizontal cylinders—no vertical positioning of horizontal press cylinders necessary, which eliminates cylinder collisions. Lower counter-bearings adjustable in several positions for the optimal insertion height. 3 kW compact hydraulic system with integrated control block, variable pressure control from 20 - 120 bar, manometer included. Operation via tactile switches with separate control circuits for the vertical and horizontal press cylinders, mounted on a freely movable control panel. 2 double-acting vertical press cylinders, stroke matched to working height, piston diameter 60 mm, max. pressure per cylinder 2100 kg 2 double-acting horizontal press cylinders, 80 mm stroke, piston diameter 40 mm, max. pressure per cylinder 1250 kg Counter bearing and pressure plate depth: 100 mm Control cabinet at the left machine base, 400V, 50Hz Machine supplied with ready-to-connect 16A plug Paint finish: RAL 7035 light gray with RAL 7016 anthracite gray Working size: Length x Height = 4,500 mm x 2,750 mm Note: Actual working size: 4,500 x 3,000 mm (L x H) Space requirement: 5,500 mm x 1,400 mm x 3,550 mm (L x W x H) Item Medium pressure beam complete with pressure cylinder, hose and shut-off valve, up to 2,750 mm height Note: actual working height: 3,000 mm Item Individual pressure control for medium pressure beam, pressure range up to max. 100 bar (for pressing Georgian bar windows) Item Continuously height-adjustable cross pressure device, complete with pressure cylinder and counter-bearing, throttle and shut-off valve Item Individual pressure control for cross pressure device pressure control range up to max. 100 bar (for pressing Georgian bar windows) Item Shut-off valve at 3rd vertical cylinder Item Shut-off valve at upper horizontal cylinder Item x Angled window control for vertical cylinder Item x Swivelling pressure plates, attachable for pressing up to 60 degrees Item Double swivelling pressure plate for pointed windows (triangle) Gedpfx Aswg Hr Toh Dekc Item x Extension for swivelling pressure plate

Stanje: rabljeno, Slot spindle 1 pc. Number of milling units: 4 pcs. Spindle diameter: 50 mm Control: Weinig, PC-Nexus #2764 Weinig Unicontrol 6 with NC spindles The machine is cleaned and thoroughly inspected prior to delivery. Summary of technical specifications (Please inquire about any optionally included accessories) Position 1: Crosscut Saw ----- > Electronic crosscut saw, horizontally adjustable, stepless > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.0 kW > Laser alignment light for cutting position detection > NC length stop, mounted on slot table included Crosscut saw positioning integrated into control system. > Length: 3500 mm Position 2: Tenoning and Slotting Spindle ----- > Number of tools: variable, infinitely adjustable via NC axis > Tool clamping length: 320 mm > Spindle vertical stroke: variable, infinitely adjustable up to 254 mm via NC axis > Spindle speed: 3,500 rpm > Spindle diameter: 50 mm > Max. tool diameter: 320 mm > Motor power: 11 kW Position 3: 1st Profiling Spindle (Climb and Counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6,000 rpm > Spindle diameter: 50 mm > Max. tool diameter: 232 mm > Motor power: 7.5 kW Position 4: 2nd Profiling Spindle ----- > Position: vertical right > Number of tools: variable, infinitely adjustable via NC axis > Tool clamping length: 320 mm > Spindle vertical stroke: variable, stepless up to 254 mm via NC axis > Spindle speed: 6,000 rpm > Spindle diameter: 50 mm > Max. tool diameter: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Sash guide consisting of: Guide rail on the stop (area of climb spindle), Sash support rail from above in the area of the vertical right profile milling unit and profiling spindle. Position 5: Horizontal Profile Milling Unit, Top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed: 5,850 rpm > Max. tool diameter: 130 mm > Axial adjustment travel: 30 mm, 8 positions via pneumatic turret > Radial adjustment travel: 125 mm, 8 positions via pneumatic turret Position 6: 3rd Profiling Spindle (Hardware Spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment travel: 115 mm, 8 positions via pneumatic turret > Radial adjustment travel: 100 mm, 8 positions via pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool diameter: 210 mm > Motor power: 3.0 kW Additional Features Gedpfx Ahovu Hfqj Dekc ----- > Online-capable > Rebatting device for tear-free rebating > Double-part package > Return conveyor for single-person operation: lamella conveyor > Screen control > Angled sash device > Electronic angle display for angled sashes > Industrial PC, PC control/NEXUS > Weinig type production program > Supplied without machining tools No original photos available yet. Images show an identical machine from our archive. ----- Price for the above-mentioned machine on request! ----- Option with surcharge: EUR 6,500.00 ...

Stanje: rabljeno, Number of sanding units: 4 units Sanding width: 190 mm Maximum sanding height: 180 mm Control: yes Weight: 3,300 kg Dimensions (L x W x H): 2,600 x 920 x 1,890 mm Extraction port diameter: 2 x 180 mm, 2 x 120 mm Double-sided sanding machine Löwer DSM 2004 Double-sided four-belt solid wood sanding machine for sanding solid wood, such as window scantlings, etc. Heavy-duty, premium build with innovative details. Suitable for continuous heavy-duty operation with higher removal rates. - Sequentially arranged sanding units for coarse sanding, fine sanding, and finishing, each from above and below 1. Belt sanding unit with heavy-duty steel roller 2. Belt sanding unit with rubber-coated roller and pad 3. Finishing unit with fiber brush - Direct-drive sanding rollers for slip-free power transmission - Maintenance-free and wear-free CERMET-coated sanding shoes with excellent thermal conductivity and precise dimensional accuracy - External cooling of sanding zones for cooler sanding and longer belt life - Forced-guided, pneumatically controlled sanding belt oscillation - Effective sanding dust extraction directly at the sanding rollers - Fine dust extraction at tension rollers - Integrated brushing and finishing unit with large sanding dust extraction - Motorized sanding thickness adjustment via precision lead screws and large linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Chip removal adjustment at the bottom via precision lead screw with indicator ring (resolution 0.1mm) - Sanding belt tensioning via pneumatic cylinder with constant tension pressure - Quick sanding belt change with pneumatic belt release in seconds - Adjustable belt tracking during belt change - Electropneumatic air pressure monitoring - In-feed protection via contact roller for oversized workpieces - Workpiece transport via calibrated, slip- and grip-resistant conveyor belts over heavy cast iron tables with finely planed surfaces and spring-loaded, finely adjustable hold-down rollers - Cardan shaft drive for smooth and uniform workpiece transport - Feed gearbox motor with stepless speed control from 4 to 20 m/min - All motors electrically protected - Ergonomically arranged control elements - Digital thickness display (resolution 0.1mm) with modern magnetic tape system Technical Data: - Sanding belt speed: 22 m/s - Sanding belt length: 1,800 mm - Sanding belt width: 200 mm - Working width: 190 mm - Sanding thickness: 2–180 mm - Four brake motors for drive: 5.5 kW - Feed motor: 1.5 kW - Feed speed: 4–20 m/min - Automatic height adjustment: 0.37 kW - Two brush units with fiber brushes D 120 x 200 mm, each 0.37 kW - Extraction ports: 2 x 180 mm, 2 x 120 mm - Extraction air speed: 20 m/s - Pneumatic connection: 6 bar - Working height: 870 mm Gksdpfxjvu Hgbj Ah Dec - Length (with soft disc: 2,740 mm), 2,600 mm - Length with control panel (with soft disc 3,035 mm): 2,985 mm - Width: 880 mm - Height: 1,910 mm - Weight: approx. 3,300 kg - Operating voltage: 400 V, 50 Hz, 3P - CE certified Equipped with the following options: - Sanding belt blow-off for 4-belt Arranged by nozzles directly at the radii of the tension rollers within the extraction, can be switched on separately - Disc unit for fiber removal - Two flap wheel sanding discs with 200 mm diameter (max. sanding width 180 mm) - Side ...

Stanje: novo, Bore diameter variable mm Number of horizontal drilling heads: 3 pcs Number of vertical drilling heads: 4 pcs Dimensions (L/W/H): 6100 x 1500 x 2300 mm Weight: 950 kg 1 NEW Drilling and Milling Center Götzinger Power Drill 300 With the Götzinger PowerDrill, depending on the requirements and configuration, you can: Gkjdpfx Ahsif Az Us Doc - Drill on end faces and longitudinal sides - Dowel door leaves, muntins, transoms - Drilling patterns are freely programmable - You can drill for handle olives and corner bearings using quick-change multi-spindle drilling heads - You can mill and drill for lock cases, lever handle sets, PZ cylinders, and 3D hinges - The machine is equipped with both horizontal and vertical milling units - Simple control allows you to create, save, and recall drilling and milling programs as needed Sturdy base frame with sheet metal cladding Table support: 1800 x 200 mm Processing units: X-axis – 500 mm effective travel Y-axis – 0–120 mm Z-axis – 0–105 mm (above the table) Horizontal units: 1 horizontal drilling unit (left dowel drilling unit) ----- Drill motor 220 V, 1.1 kW Collet chuck ER 25 4,000 – 11,000 rpm, adjustable 1 horizontal milling unit for lock cases ----- Milling motor 2.2 kW Speed adjustable, 3,000 – 16,000 rpm Collet chuck ER 25 1 horizontal drilling unit (right dowel drilling unit) ----- Drill motor 1,100 W, infinitely variable 4,000 – 11,000 rpm with ER 25 collet chuck Vertical units: 1 vertical drilling unit ----- Drill motor 1,100 W, infinitely variable 4,000 – 11,000 rpm with ER 25 collet chuck 1 vertical drilling unit – with quick-change drill head system ----- Drill motor 1.1 kW, 3,000 rpm Included: 1 Drill Head BKF 2/3, for corner bearing insertion, quick-changeable ----- For loose single parts, drill arrangement according to customer's hardware 1 Drill Head BKF 3, for handle olive including drill bits, quick-changeable ----- For loose single parts, drill bits: 1 Kubo d = 25, 2 x Dübo d = 10 1 vertical milling unit for lock case ----- Milling motor 2.2 kW Speed adjustable, 3,000 – 16,000 rpm Collet chuck ER 25 1 length stop left and right, useful length 2.7 m, NC controlled Control: electro-pneumatic with three axes NC position controller and integrated machine functions Input via TFT display, 10" color Machine complete, CE compliant, with 1 set of drilling tools: DÜBO each 1 x d = 6, 8, 10, 12 + 2 roughing end mills d = 16, ready to connect Shipping dimensions: Machine L x W x H = 2.50 x 1.50 x 2.30 m, weight 850 kg Length stop L x W x H = 6.00 x 0.30 x 0.30 m, weight 100 kg ----- Total price for the above configuration, ex works: on request Plus freight and installation/commissioning (Technical data as provided by manufacturer – no guarantee!)

Stanje: novo, Bore diameter variable, mm Number of horizontal boring heads: 1 pc. Number of vertical boring heads: 0 pcs. 1 Götzinger Dowel Gluing and Insertion Machine BLE The BLE is used to apply glue and insert dowels into the end faces of workpieces. Optionally, the BLE can be upgraded with a drilling unit, counter milling unit, and longitudinal stop. A 10" touch panel enables easy operation in manual or online mode. Basic Frame: compact design, covered with sheet metal Table size approx. 800 x 200 mm Pos. 1 ----- 1 Glue station Full-jet valve Precisely adjustable glue quantity Glue gun for opposing hole application Pos. 2 ----- 1 Stainless steel glue pump, high-pressure pump and glue hose Pos. 3 ----- 1 Insertion station with dowel singling device and insertion cylinder Pos. 4 ----- 1 Vibratory feeder for dowels d 8 x 50 mm with feed hose to the insertion unit Pos. 5 ----- 1 Processing unit with cross table, linear guide, and 3 NC-axis motors X = 200 mm processing width Y = 120 mm processing height Z = 50 mm insertion depth Pos. 6 ----- 1 Positioning control 10" color touch panel Up to 500 drilling patterns can be created and stored, which can be easily recalled as needed (1 drilling pattern can have up to 16 dowel positions) Software prepared for ONLINE connectivity Godpfxju Uu Uzj Ah Dekc For online control, the data must be prepared in the appropriate software format for the controller – our machine can receive and process these data. ----- Total price for version with Pos. 1 to Pos. 6: on request! Optional equipment and surcharges: ----- Pos. 7 ----- 1 horizontal drilling unit, 1,000 W drilling motor Speed 4,000 – 8,000 rpm, collet chuck mounting Drill feed: pneumatic Surcharge: EUR 4,305.00 Additional accessories such as larger touch screen, additional dowel station for different dowel sizes, scanner for program selection, or top rail gluing, available on request! Prices are net plus statutory VAT, excluding packaging/shipping and commissioning. (Technical data according to manufacturer – subject to change and without guarantee!)

Stanje: novo, Working width: 3,500 mm Working height: 2,300 mm Number of pressure cylinders: 4 pcs. S&S Frame Press Type RP 2000 – CE version Gjdod Ih H Sepfx Ah Djkc Options: Working widths from 3,000 mm to 5,000 mm Working heights from 2,000 mm to 3,000 mm Optional equipment includes central pressure beam, angled window device, counter profiles for single-part production, and much more! Request our complete price list! Description: Robust frame welded construction made of thick-walled special profiles, sliding carriages, and pressure beams with 50 mm hole pitch. Continuous left-side abutment for width pressing, lower abutment on two levels. Vertical pressure cylinders on special pressure beams with single-hand quick adjustment and weight compensation, height-adjustable in 50 mm increments; long sliding carriages ensure sustained absorption of high pressing forces. Quick and smooth width adjustment via ball-bearing guide carriage with central locking, fixing in 50 mm increments. Upper horizontal pressure cylinder infinitely height-adjustable and equipped with weight compensation. Lower horizontal pressure cylinder with centering bores for both abutment levels, no weight compensation. Abutment and pressure plate depth 100 mm. Pressure plate and support width 130 mm. Machine controlled electro-hydraulically, with 2 vertical pressure cylinders, Ø 50 mm, stroke 120 mm, single-acting, with weight compensation and single-hand quick adjustment; 2 horizontal pressure cylinders, Ø 40 mm, stroke 120 mm, double-acting with weight compensation; 2 manual control valves, manometer, 1 pressure control valve from 20 to 100 bar corresponding to 400 to 2,000 kg pressing force vertically; powered by 3 kW three-phase motor for 400 V, 50 Hz operating voltage. Complete with electrical connection. Paint finish: RAL 7035 light grey with RAL 7016 anthracite grey. (Technical data according to manufacturer without guarantee, images may show optional equipment!)

Stanje: rabljeno, max. tool diameter, mm Max. tool height, mm Operating pressure, bar Filling volume: 52 l Quicksonic QS 520 Ultrasonic cleaning unit with lid and work basket ----- Technical manufacturer description: External dimensions (length x width x height): 560 x 460 x 510 mm Usable dimensions (length x width x height): 500 x 400 x 260 mm Basket usable dimensions (length x width x height): 444 x 364 x 224 mm Capacity: approx. 52 l Ultrasonic Power Effective nominal power: 800 Watt Peak power: 1600 Watt Operating frequency: 40 or 25 kHz Supply voltage: L+N+PE, 230 V/50-60 Hz Heating power: 2000 Watt Gksdpsumng Ajfx Ah Doc Heating control: 30 - 85°C Timer: 0-15 min & continuous operation ----- All prices ex works plus packaging, transport, insurance as well as statutory VAT. (Technical data as per manufacturer – subject to change and errors excepted!)