Portal Glodalica nakup rabljenega (1.520)

Leto izdelave: 1987, stanje: rabljeno, številka stroja/vozila: 7.0176, Note: We have 6 units of this machine in stock! Manufacturer: Gildemeister Type: GS 36 – 6 A/C Machine No.: 7.0176 Year of manufacture: 1987 Weight: 11 t General / Technical Data: Portal 6-spindle automatic lathe Spindle pitch circle diameter: 300 mm Number of longitudinal slides: 6 Number of cross slides: 2 Max. cross slide travel: 60 mm Max. longitudinal slide travel: 125 mm Spindle speeds: Infinitely variable 562 – 3373 rpm Main time range: Infinitely variable 1.95 – 78 sec. Nonproductive time range: 0.79 – 2.13 sec. Drive power: DC motor spindles 20 kW; feed drives 8 kW Footprint: approx. 1720 x 4700 mm Note: The machine cannot be converted for bar work. Equipment: – 1 creep feed drive for setup operation – 1 automatic central lubrication system – 1 coolant system with pipes and pump – 1 facing slide, position 3 (without cams) – 1 facing slide, position 5 – 6 longitudinal slides (without drive, without cams) Fjdpfoin Ub Tox Ahmsph – Feed for independent longitudinal slide, flexible, positions 1-6 – Programmable logic controller IPC 620 – Noise protection measures 80 dB – Automatic feed re-engagement with electric interlock on side door – Hinged belt chip conveyor – Machine version with DC drives for speed and feed – KIENZLE terminal 2450-07 with signal interface and data transmission control Accessories: Electrical configuration: The electrical equipment consists of a DC main drive with 20 kW power output for spindle drive and an AC servo motor for feed drive with 8 kW power output (protection rating IP 54), as well as the corresponding switching and control devices and necessary installation. Total connected load for the machine: 32 kW/h.

Stanje: novo, Leto izdelave: 2024, obratovalne ure: 50 h, številka stroja/vozila: 305, Available: February 2023 Control system: Osai X-axis: approx. 3,100 mm Y-axis: approx. 2,100 mm Z-axis: approx. 1,000 mm A-axis: ± 115° C-axis: ± 360° Clamping Table Clamping surface: approx. 3,100 x 2,100 x 213 mm Aluminium with T-slots, crosswise every 250 mm Fsdpfxjwwq Hco Ahmjph Max. load: 1,000 kg evenly distributed over the entire surface 2-axis milling head ST7 Spindle power: 10 kW Spindle speed: max. 24,000 rpm Torque: 15.3 Nm Tool holder: HSK 63F Tool clamping: pneumatic Blow air / MQL: external Linear axis drives Feed rate X and Y axes: up to 50 m/min Feed rate Z axis: up to 30 m/min Colour Enclosure, gantry, control cabinet: light grey Z-slide and milling head: orange Additional equipment - 15-position tool changer - Control unit in separate, mobile console

Stanje: zelo dobro (rabljeno), Leto izdelave: 2012, Initial commissioning: 2012 Control: Heidenhain iTNC 530 incl. HR 420 handwheel X-axis: approx. 5,000 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,500 mm A-axis: ±110° C-axis: ±300° Clamping Table Clamping surface: approx. 5,700 x 3,000 x 300 mm 2-axis Milling Head VH20 Spindle power: 40 kW Spindle speed: max. 25,000 rpm Torque: 48 Nm Tool holder: HSK 63A Tool clamping: hydraulic Coolant supply: external and internal Blow air: external Linear Axis Drives Feed rate X, Y-axis: up to 50 m/min Feed rate Z-axis: up to 30 m/min Axis acceleration X, Y, Z: up to 2.5 m/s² Connection Data Connected load: 190 kVA Main fuse: approx. 315 A Dimensions, Weight Space requirement incl. peripherals: approx. 10,000 x 7,700 x 5,850 mm Total weight: approx. 63,000 kg Color Enclosure, gantry, control cabinet: RAL 7035 light grey Milling head and applications: RAL 6038 luminous green Additional Equipment - Coolant supply with belt filter system - 30-position chain tool changer - Work area enclosure - Chip conveyor, right side Fpedpfx Aevy A Tnehmoh Optional for an additional charge: - BLUM laser Machine condition Fully functional, very good condition. Already dismantled and in storage.

Stanje: novo, Leto izdelave: 2025, številka stroja/vozila: 306, Initial commissioning: 2024 Control: Heidenhain TNC 640 incl. HR 520 handwheel X-axis: approx. 4,000 mm Y-axis: approx. 2,700 mm Z-axis: approx. 1,300 mm A-axis: ± 120° C-axis: ± 360° Clamping table Clamping area: approx. 4,000 x 2,500 x 213 mm Aluminum with T-slots crosswise every 250 mm Max. load: 1000 kg evenly distributed over the entire surface Fodpovy Dugofx Ahmeph 2-axis milling head HS673 Spindle power: 22 kW Spindle speed: max. 24,000 rpm Torque: 18 Nm Tool holder: HSK 63A Tool clamping: pneumatic Blow air / MQL: external Linear axes drives Feed rate X and Y axes: up to 60 m/min Feed rate Z axis: up to 40 m/min Color Enclosure, gantry, control cabinet: light grey Z-slide and milling head: orange Additional equipment - Work area cover - 16-position tool changer - Control on separate, mobile console Optional at extra charge: - Blum laser tool measurement - Renishaw RMP60 radio probe - Heidenhain remote diagnostics Pictures show an identical machine with slightly different equipment!

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, Initial commissioning: 2014 Control system: Heidenhain iTNC 530 HSCI incl. HR 520 handwheel Machine hours Machine power-on hours: approx. 90,000 h Spindle hours: approx. 38,000 h Current milling spindle hours: approx. 900 h Travel distances X-axis: approx. 2,500 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,250 mm A-axis: ± 110° C-axis: ± 300° Clamping table Clamping surface: approx. 2,500 x 3,250 x 600 mm 2-axis milling head VH30 Spindle power: 60 kW Spindle speed: max. 22,000 rpm Torque: 95 Nm Tool holder: HSK 63A Tool clamping: hydraulic Coolant supply: external and internal Drives linear axes Feed rate X/Y/Z-axis: up to 60 m/min Axis acceleration X/Y/Z-axis: up to 5 m/s² Connection data Connected load: 190 kVA Main fuse: approx. 315 A Dimensions, weights Space requirement machine with peripherals: approx. 10,000 x 8,000 x 5,650 mm Total weight: approx. 63,000 kg Colour Enclosure, gantry, control cabinet: RAL 7035 light grey Milling head and applications: RAL 6038 luminous green Description: Additional equipment Fsdpfxswywcio Ahmsph - Coolant supply with belt filtration system - 50-position chain tool changer - Workspace enclosure - Chip conveyor - LTA emulsion mist extraction system Optional at extra charge: - Renishaw RMP60 wireless measuring probe - BLUM Control NT Condition of the machine Fully functional, in excellent condition, and still under power for inspection! The photos are for illustration purposes and show a new machine of this type. Original photos will follow shortly!

Leto izdelave: 2003, stanje: pripravljen za uporabo (rabljen), - GEBRAUCHT - 5-ACHSEN-BRÜCKENFRÄSMASCHINE MIT DREHTISCH LÄNGSVERFAHRWEG: 2.700 mm QUERVERFAHRWEG: 1.100 mm VERTIKALVERFAHRWEG: 1.400 mm EILGÄNGE L-Q-V: 24 m/min TISCHGRÖSSE: 1.800 x 1.800 mm MAXIMALE TISCHBELASTUNG: 15.000 kg SPINDEL: 240–24.000 U/min; 34 kW KOPF: KONTINUIERLICHE AUTOMATIK A/B-ACHSE; A-Achse -110°/+95°, C-Achse ±200° WERKZEUGMAGAZIN: KETTENAUSFÜHRUNG; 42 PLÄTZE STEUERUNG: FIDIA C20 ABSTAND SPINDELNASE-TISCH: 1.600 mm MASCHINENGEWICHT: 21.500 kg GESAMTABMESSUNGEN: 5.950 x 5.430 x 5.220 mm ZUBEHÖR: SPÄNEFÖRDERER; Fedpewmxnmjfx Ahmsph HANDRAD (PORTABEL)

Leto izdelave: 2015, stanje: pripravljen za uporabo (rabljen), - RABLJEN - 5-OSNI MOSTNI CNC REZKALNI STROJ PREMIK VZDOLŽNA OS: 2200 mm PREMIK PREČNA OS: 3500 mm PREMIK VERTIKALNA OS: 1400 mm HITRI POMIKI L-T-V: 30 m/min VELIKOST MIZE: 3500 x 2200 mm GLAVA: A/B OS SAMODEJNA; HSK-63A; A-os -110°/+95°, B-os ±360°; 24000 vrt/min MENJALNIK ORODIJ: VERIŽNI TIP; 42 POZICIJ KRMLJENJE: FIDIA C40 Vision RAZDALJA MED STEBRI: 4200 mm Fsdpfxowlwg Sj Ahmeph TEŽA: 62000 kg DODATNA OPREMA: TRANSPORTER OSTRUŽKOV; PRENOSNA ROČICA

Leto izdelave: 1993, stanje: pripravljen za uporabo (rabljen), - UPORABLJEN - 5-OSNI PORTALNI CNC REZKALNI STROJ Fedpfxowla H Uo Ahmeph POT V DOLŽINI: 2800 mm POT V PREČNI SMERI: 2200 mm POT V VERTIKALNI SMERI: 1500 mm HITRI POMIKI D-P-V: 20 m/min DIMENZIJE MIZE: 3000 x 2000 mm NAJVEČJA DOVOLJENA OBREMENITEV: 20000 kg GLAVA: A/B OSI AVTOMATSKI; ISO 30; A-os ±100° - B-os ±185°; 15000 vrt/min; 11 kW MENJALNIK ORODIJ: VERIŽNA REVOLVERKA; 12 POZICIJ KRMILNA ENOTA: FIDIA CXR10 RAZDALJA MED STEBRI: 3600 mm SKUPNE DIMENZIJE: 7000 x 4000 x 6485 mm DODATKI: PRENOSNA ROČICA

Stanje: zelo dobro (rabljeno), Leto izdelave: 2001, številka stroja/vozila: 24205, Funkcionalnost: popolnoma funkcionalen, vhodna napetost: 400 V, vrsta vhodnega toka: trifazni, potovalna razdalja osi X: 4.800 mm, pomik osi Y: 1.800 mm, pomik po osi Z: 100 mm, dolžina obdelovanca (maks.): 4.800 mm, širina obdelovanca (maks.): 1.800 mm, število mest v zalogovniku orodij: 18, skupna masa: 16.000 kg, moč vretenovega motorja: 12.000 W, število vreten: 1, premer obdelovanca (maks.): 1.800 mm, Oprema: dokumentacija / priročnik, transportni trak za ostružke, Izjemen stroj z izjemno kakovostnim izhodom. Stroj je bil servisiran s strani IMA serviserjev, uporabljeni so bili originalni rezervni deli. Optični kabel ter večina cevi za stisnjen zrak sta bila zamenjana z novimi. Avtomatsko pozicioniranje vakuumskih prijemal bistveno pospeši čas nastavitve. ImaWoop verzija 6.0 s funkcijo Quicktool dodatno olajša delo operaterja. Vabljeni, da si kadarkoli osebno ogledate delovanje stroja. Prav tako je možno vsak čas spremljati delovanje stroja preko video povezave v živo. CNC portalni obdelovalni center proizvajalec: IMA tip: BIMA P 480 V, 180/480 leto izdelave: 2001 Kratek opis Stroj zmore številne zahtevne naloge (rezkanje, vrtanje, razrez, lepljenje robov, različno kotno rezanje) - izmenično obdelovanje - X = 2 x 2.400 mm, Y = 1.800 mm - glavni vreteno 12 kW - 18-pozicijski menjalec orodij - lepilna enota s 6-pozicijskim zalogovnikom za kolute Opis Delovno območje: z osnovnimi enotami Y = 1.800 mm menjalna miza za izmenično obdelavo: X = 2 x 2.400 mm (rezkanje in vrtanje) X = 2 x 2.100 mm (lepljenje) CNC linijski krmilnik IMATRONIC NT 231 Programska oprema Imawoop 6.0 Avtomatsko pozicioniranje vakuumskih prijemal Avtomatsko mazanje Transportni trak za odpadke in ostružke (trakasti) Glavni vreteno 12 kW z integrirano C-osjo, 360 stopinj Fsdstt Rpwjpfx Ahmsph Avtomatski menjalec orodij/priključnih enot, 18-kratni 1 enota za lepljenje robov VT100 z enoto za nanašanje lepila Debelina roba: 0,4–3 mm za 4-stransko in obodno lepljenje z ravnim stikom 6-pozicijski zalogovnik kolutov 1 enota za končno obrezovanje 0,8 kW Vključeni priključki: - žaga s fiksnim kotom 90° - horizontalna vrtalna enota s 4 izhodi - enota za obdelavo ABS robov - enota za zaobljanje in vodoravni strgalnik ABS robov Drugi priključki in orodja so na voljo proti doplačilu Transportni trak za odsesavanje odpadkov Klimatska naprava v elektro omari

Leto izdelave: 2004, stanje: dober (rabljeno), številka stroja/vozila: 2004-3-11A, - Manual feed of the milling unit - Working table height adjustable via handwheel - Horizontal and vertical material clamping - Cutter diameter up to 250 mm - Max. milling height: 150 mm - Max. milling depth: 80 mm - Max. milling length: 305 mm - Angle-adjustable fence left & right: 20° – 90° - Spindle speed: 4,500 rpm - Drive: 400 V, 3.2 kW - Compressed air connection: 6 – 8 bar - Air consumption per work cycle: 10 l - Pneumatic profile clamping - Table base frame - Space requirement: approx. W 1,100 x H 1,300 x D 700 mm - Weight: approx. 200 kg Fpedpfxof E Higo Ahmoh

Leto izdelave: 1997, stanje: rabljeno, številka stroja/vozila: B-388, FIL FA 160 bed-type milling machine with HEIDENHAIN TNC-360 control Fodpfx Aogcuzrehmoph

Stanje: rabljeno, Linearno vodilo, portalo os SCHNEIDER ELECTRIC / FESTO Električna sani Tip motorja: ILS1B571PC1A0 Leto izdelave: 2010 Pomik osi: 300 mm Napajalna napetost: 36 V (DC) Voziček: 86 x 54 mm - Sinhronski servomotor / koračni motor SCHNEIDER ELECTRIC, tip: ILS1B571PC1A0 - Linearno vodilo FESTO, tip EGSK-33-300-6P - Kroglasta vretena Ø 10 mm, korak 6 mm - 2 nastavljiva pozicijska senzorja Dimenzije (D x Š x V): 580 x 120 x 57 mm Fpedpfxow Uc Tzo Ahmsh Teža: 6,5 kg V dobrem stanju

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2008, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 3.000 mm, pomik osi Y: 6.000 mm, pomik po osi Z: 1.250 mm, največja hitrost vretena: 12.000 obr/min, model krmilnika: Heidenhain iTNC530 mit Handrad, Stroj s 4. osjo kot zasučno osjo & redno vzdrževanje s strani proizvajalca! TEHNIČNI PODATKI Delovna območja Os X: 3.000 mm Os Y: 6.000 mm Os Z: 1.250 mm Fedexvx U Aspfx Ahmeph Glava za rezkanje, os A: krmiljeno zasučna Rezkalno vreteno Moč vretena: 4,4 kW Hitrost vretena: 12.000 min⁻¹ Vpenjanje orodja: 78/8 prirobnica Menjava orodja: ročna z navojno matico Pogoni linearnih osi Premična hitrost osi X, Y, Z: do 20 m/min Pospešek osi X, Y, Z: do 1,5 m/s² PODROBNOSTI O STROJU Krmiljenje: Heidenhain iTNC530 z ročnim kolesom Priključna moč: cca 25 kW Predvarovalka: 42 A Dimenzije & teža Potrebni prostor stroja: cca 5.500 x 9.000 x 4.500 mm Skupna teža: 9.600 kg OPREMA Možnost predelave na visoko frekvenčno vreteno Pomembno: Miza in na fotografijah prikazana lesena plošča nista vključeni v obseg dobave.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 6.000 mm, pomik osi Y: 2.700 mm, pomik po osi Z: 1.250 mm, največja hitrost vretena: 24.000 obr/min, obremenitev mize: 15.000 kg, The submission of a bid obligates the buyer to collect the item within the specified period, no later than 27.11.2025! The machine can still be viewed under power until calendar week 47. The new spindle was installed in 2025! Additionally, the tool changer was retrofitted in 2025. The control unit was upgraded in 2014! TECHNICAL DETAILS Working Areas X-axis: 6,000 mm Y-axis: 2,700 mm Z-axis: 1,250 mm Clamping Table Fedpfxoxr U Drj Ahmeph Table dimensions (L x W x H): 6,600 x 2,740 x 520 mm Table load capacity: max. 15,000 kg T-slots and spacing: 10 x 22H8 / 255 mm Spindle Spindle power: 10 kW Spindle speed: 24,000 rpm Tool interface: HSK 63F Tool clamping: pneumatic Torque: 8.7 (S1) and 10.5 (S6) Nm Suitable materials: wood, plastic, aluminum Linear Axes Drives Rapid traverse speed X, Y, Z axes: max. 20 m/min Axis acceleration: max. 1.5 m/s² MACHINE DETAILS Control: Heidenhain iTNC530 with electronic handwheel Connection Data Power requirement: 28 kW Pre-fuse: 63 A Dimensions & Weight Machine footprint: 10,000 x 5,000 x 4,500 mm Total weight: 28,000 kg EQUIPMENT Double-sided enclosure with two doors 6-position tool changer

Leto izdelave: 2008, stanje: zelo dobro (rabljeno), ZEISS ACCURA 16.24.10 RDS-CAA X 1,600 / Y 2,400 / Z 1,000 Probing system: RDS CAA with VAST XXT technology Probe changer rack with 8 positions C99 controller Software available on request – Calypso / HolosNT 12-month warranty Fpsdpfjnp Hvusx Ahmsh Installation, commissioning, and acceptance according to DIN EN ISO 10360-2,4,5

Stanje: dober (rabljeno), Leto izdelave: 2017, obratovalne ure: 9.380 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 4455, numerically controlled machining center Fsdpfx Aher E D Eajmeph max. panel sizes: 4,000 x 2,300 mm 1 Kuka KR420R3300 robot 1 Kuka KR200L140 robot 1 Kuka KRL140-3Comp robot conveyor belt for scrap metal removal Ruwac Zone 22 extraction system

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, Funkcionalnost: popolnoma funkcionalen, lastna masa: 8.400 kg, Z oddajo ponudbe se zavezujete k pravočasnemu prevzemu v 1. ali 2. tednu 2026! Fpodjxzubpopfx Ahmoh Stružnica s portalnim nakladanjem! PODROBNOSTI O STROJU Teža: 8.400 kg

Stanje: dober (rabljeno), prevoženi kilometri: 361.156 km, moč: 260 kW (353,50 KM), prva registracija: 06/2018, vrsta goriva: dizel, konfiguracija osi: 4x2, gorivo: dizel, zavore: zaviranje z motorjem, barva: bela, voznikova kabina: dnevna kabina, vrsta prenosa: samodejen, vzmetenje: jeklo-zrak, Leto izdelave: 2018, Oprema: AdBlue, Bluetooth, EBS (Elektronski zavorni sistem), električno nastavljivo ogledalo, električno upravljanje oken, filter saj, meglenke, navigacijski sistem, spojka prikolice, tempomat, - Aluminum fuel tank - Brake booster - EPS (Electronic Steering System) - Low noise - Tipping hydraulics - Particulate filter - Radio/CD player - Reversing camera - Sliding roof - Sleeper cab - Side door - Toolbox Front axle: Steering; Suspension: Leaf spring Rear axle: Suspension: Air suspension Unladen weight: 10,150 kg Payload: 7,850 kg Gross vehicle weight: 18,000 kg APK (Periodic Technical Inspection): valid until 07/2026 Technical condition: good Visual condition: good No liability for typographical errors, changes, prior sale, and mistakes reserved! Vehicle number: 115 Mercedes Benz Antos 1835 / 4x2 / Meiller AK 12MT with radio remote control / 361,000 km VIN: WDB96300310267671 German vehicle TÜV: 01/2027 - SP: 07/2027 Suspension: leaf/air Transmission: automatic Stationary air conditioning Engine brake Cruise control Navigation system Distance control assist Lane keeping assist Reversing camera Euro 6 Skip loader Meiller: AK 12MT Year of manufacture: 2018 With radio remote control Special equipment: Driver's airbag, audio system: CD-radio (Bluetooth), exhaust routed upwards behind cab, right exterior mirror with maneuvering position, compressed air connection in cab, driver assistance system: Attention Assist (fatigue detection sensor), suspension: front springs 7.5 t, single leaf, transmission 12-speed - type: G 211-12, rear lights LED, info display 12.7 cm with video function, fuel tank: 390 l aluminum, reinforced engine brake, power take-off MB 124-10c, programmable special module, frame lowering without bellows residual pressure control, circuit breaker, cab seats: comfort driver's seat with suspension, exterior sun visor, additional stabilizer, rear axle/tag axle, additional 24V socket in passenger footwell, transmission oil cooler Additional equipment: Emission standard EURO 6, axle configuration: 4x2, front axle load 7.5 t, trailer brake 2-line, left-sided connections, 24V / 15-pin trailer socket, Antos, electrically adjustable and heated exterior mirrors, 170 Ah battery, rear axle differential lock, steel compressed air tank, medium compressed air unit, driver assistance system: brake assist (Active Brake Assist), driver assistance system: lane keeping assist, Cab: width 2.30 m, cab: hydraulic tilting device, cab: M ClassicSpace, cab: steel-sprung, standard, cab: reinforced (Sweden), cab floor with 320 mm engine tunnel, suspension: leaf/air, electric window lifters, tinted windscreen, 100 A alternator, urea tank (AdBlue): 60 l, manual roof hatch (steel), rear axle bevel gear 440, body/chassis: chassis, central locking system, non-regulated power steering pump, front air intake, engine 7.7 l - 260 kW inline 6-cylinder diesel (OM 936), engine compartment encapsulation, ramp mirror, spare wheel, residual heat utilization, disc brakes front and rear, seat cover/upholstery: fabric, cab seats: passenger functional seat, front mudguard, front axle stabilizer, 24V cab socket, tachograph / EC control unit, aerodynamically shaped underbody paneling, front underrun protection, toll system preparation, cranked front axle, permitted total weight 18.00 t Fodpjyyddmofx Ahmsph No liability for typographical errors, changes, prior sale, and mistakes reserved!

Stanje: rabljeno, Leto izdelave: 1998, Portalna rezkalna stroj JOBS JOMACH 241 Leto izdelave: 1998 Pomiki X: 3400 mm Pomiki Y: 2700 mm Pomiki Z: 1250 mm Numerični krmilnik: CNC Siemens SINUMERIC 840 D Velikost mize: 3000 x 1500 mm Razdalja med stebri: 1700 mm 1 menjalnik orodij za 32 orodja ISO 50 + 1 menjalnik orodij za 32 orodja HSK-63 Fpedpsyrcyiofx Ahmeh 3 rezkalne glave – os C: 2 glavi TWIST – ISO 50 + HSK 63 A + 1 glava 3 osi ISO 50 Teža: 44 t

Stanje: rabljeno, Leto izdelave: 2013, x-travel 6000 mm y-travel 4750 mm z-travel 1500 mm Control Siemens 840 D SL Table type: traversing table Maximum table load: 20 t Tool changer: 120 positions Tool holder: SK 50 Pallet size: 2200x1500 mm Spindle power: 46 kW Aggregates (pick-up, max. 5 positions): - Orthogonal head 1x1 degree, 4000 rpm, 46 kW - Short vertical milling attachment, 4000 rpm, 46 kW - Vertical milling attachment, 4000 rpm, 46 kW - Heavy-duty angle head, 3000 rpm, 46 kW - Long angle head, 1000 rpm, 30 kW The technical data is provided by the manufacturer or operator and is therefore non-binding for us. Subject to prior sale; exclusively our Terms and Conditions of Sale and Delivery apply. Fsdpfxsyr Aq Uo Ahmoph About us: - Over 400 machines in stock - More than 15,000 m² of warehouse space, crane capacity up to 70 t - Over 10,000 accessory items for your workshop Would you like to sell machines, production lines, or your business? Contact us. You can find further offers on our website. Inspections are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2004, obratovalne ure: 47.870 h, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 3.000 mm, pomik osi Y: 2.100 mm, pomik po osi Z: 760 mm, obremenitev mize: 10.000 kg, največja hitrost vrtenja: 6.000 obr/min, TEHNIČNE PODROBNOSTI Fpodex Agh Ropfx Ahmjh Pomik X-osi: 3.000 mm Pomik Y-osi: 2.100 mm Pomik Z-osi: 760 mm Razdalja med stebri: 2.300 mm Velikost mize: 3.020 mm × 2.010 mm Nosilnost mize: 10.000 kg Vpenjalo vretena: ISO-50 Standardna hitrost vretena: 6.000 vrt/min Moč vretena (trajna / 30 min): ca. 22/26 kW Kapaciteta menjalca orodij: 32 orodij Maks. premer orodja: Ø 127 mm / Ø 215 mm Maks. dolžina orodja: 350 mm Maks. teža orodja: 20 kg Hitro pomikanje X-osi: do 20.000 mm/min Hitro pomikanje Y-osi: 15.000 mm/min Hitro pomikanje Z-osi: 15.000 mm/min Rezalni pomik: pribl. 1 – 10.000 mm/min PODROBNOSTI STROJA Število ur programa: 47.870 h OPREMA Razširitev opreme na avtomatski menjalec glav z kotno rezkalno glavo

Stanje: dober (rabljeno), Sturdy crane system, ideal for glass storage or workshops, Load capacity: 3 t, Length: 14,250 mm, Width: 8,500 mm, Fpsdpfx Ahjryv S Ajmoh Height: 3,650 mm Maximum hook height: 3,280 mm, Maximum overall height: 3,950 mm.

Stanje: dober (rabljeno), Leto izdelave: 2008, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 6.000 mm, pomik osi Y: 3.400 mm, pomik po osi Z: 1.500 mm, dolžina mize: 6.000 mm, širina mize: 3.000 mm, hitrost vretena (min.): 3.000 obr/min, CNC portálová frézka FKD-Feichter s dvoustojanovým rámem je k dispozici. Pojezdy X/Y/Z/W: 6000mm/4800mm/1500mm/1300mm, rozměry stolu X/Y: 6000mm/3000mm, max. hmotnost obrobku: 115 000 kg, max. zatížení stolu: 6 400 kg/m², celková délka lože stroje: 14 500 mm, rozměry portálu X/Y: 3000mm/4400mm, osa C: 360°, osa A: +/-120°, průřez smykadla: 700mm/700mm, posuv: 10 m/min. Celkové rozměry zařízení X/Y/Z: cca 15 100 mm/6 100 mm/7 000 mm, celková hmotnost zařízení: cca 115 000 kg, řízení: Heidenhain. Včetně odvodu třísek, chladicího zařízení a hydraulického agregátu. Stroj byl postaven na místě v roce 2022. Smykadlo a vřeteno byly aktuálně nově repasovány. Dokumentace k dispozici. Možnost prohlídky na místě. Ihned k odběru. Fjdpexp Rgkofx Ahmjph Tři hlavy: vidlicová frézovací hlava s osou A, 90° úhlová hlava, prodloužení vřetene - rovná hlava, upnutí nástroje SK 50.

Stanje: dober (rabljeno), Leto izdelave: 1995, obratovalne ure: 43.499 h, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 4.000 mm, pomik osi Y: 2.500 mm, pomik po osi Z: 1.000 mm, 5-Axis Gantry Milling Machine WALDRICH Product manufactured on the machine: AIRBUS LANDING GEAR (aerospace) Year of manufacture: 1995; Year of delivery: 1998 Installation & commissioning: 1999 Operating period: 03/1999 to 07/2022 (21 years) Condition: Very Good Customer specifications / History Previous owner (1999–2022): German aerospace group Technical data Travel & Working Area X-axis (table longitudinal travel): 4,000 mm Y-axis (cross slide traverse): 2,500 mm Z-axis (ram vertical travel): 1,000 mm Distance between columns: 2,000 mm C-axis: 360,000 positions (increment 0.001°) B-axis: 360,000 positions Tables & Pallets Number of tables: 2 Table dimensions: 1,500 x 3,000 mm Table height above floor: 740 mm Max. table load: 12,000 kg Feed & Rapid Traverse X/Y/Z: Feed 0–6,000 mm/min, Rapid 15,000 mm/min B-axis Rotary: 0–3,600 deg/min C-axis Rotary: 0–3,600 deg/min Feed Forces / Torque X/Y/Z max.: 30 kN each C-axis detachable torque: max. 20,000 Nm C-axis bearing regulation: max. 4,000 Nm Speed Range Level I: 20–875 rpm Level II: 876–4,000 rpm Spindle Drive Power: 50 kW Speed range: 20–4,000 rpm Fedpjx Hxdzsfx Ahmoph Tool Change System Type: Chain magazine Capacity: 120 tools Tool holder: ISO 50 Max. tool Ø: 315 mm Tool Ø at full capacity: 100 mm Max. tool length: 550 mm Max. tool weight per gripper: 35 kg Spindle Units / Clearances Vertical spindle unit: spindle nose – table surface 250–1,250 mm Horizontal spindle unit: spindle centre – table surface 150–1,150 mm Rotary Nutator (MC303): spindle centre – table surface 45–1,045 mm Coolant & Lubrication Coolant supply: internal and external available Lubrication: automatic (spindle bearings and gearbox) Dimensions & Weight Machine dimensions (approx.): Length: 14,700 mm Width: 10,000 mm Height above floor: 6,079 mm Total machine weight (approx.): 72,500 kg Machine bed: 8,500 kg Machine table & pallet: 16,000 kg 2 columns: 10,200 kg Crossbeam with platform: 20,000 kg Features & Accessories Fully automatic tool changer (ATC): 120 positions (ISO 50) Fully automatic head changer incl. universal milling heads Milling head: C-axis: 360,000 x 0.001° B-axis: 360,000° Accessories: 3 chip conveyors Tool cabinet + pallets with loose accessories Packing List (Transport Dimensions) Axes: 8,950 x 1,700 x H 1,000 mm 2 tables: 3,300 x 1,700 x H 340 mm Tool changer with slide: 3,500 x 2,300 x H 2,670 mm Tool changer without slide: 4,450 x 1,060 x H 1,870 mm Pick-up heads: 3,000 x 470 x H 2,200 mm Crossbeam: 7,000 x 2,000 x H 2,500 mm 2 support columns: 2,900 x 1,000 x H 1,500 mm Slide with ram: 3,450 x 1,800 x H 2,100 mm Chain section: 3,700 x 2,000 x H 1,100 mm Electrical cabinet No. 1: 5,400 x 600 x H 2,000 mm Electrical cabinet No. 2: 2,100 x 650 x H 2,000 mm Chip conveyor: 5,000 x 500 x H 2,300 mm Head: 900 x 600 x H 700 mm Tool cabinet: 2,100 x 1,200 x H 600 mm 7 pallets with loose accessories This WALDRICH SIEGEN 5-axis gantry milling machine is ideally suited for the machining of steel, cast iron, and non-ferrous metals. The combination of a 50 kW spindle drive, automatic tool changer (120 positions), fully automatic head changer, and high-precision B-/C-axis positioning (0.001°) makes it the ideal solution for demanding and complex manufacturing tasks.

Stanje: dober (rabljeno), prevoženi kilometri: 216.019 km, moč: 338 kW (459,55 KM), prva registracija: 03/2018, vrsta goriva: dizel, velikost pnevmatike: 315/80R22,5, konfiguracija osi: 6x2, medosna razdalja: 3.950 mm, gorivo: dizel, zavore: retarder, barva: črn, voznikova kabina: dnevna kabina, vrsta prenosa: samodejen, število prestav: 12, emisijski razred: Euro 6, vzmetenje: jeklo-zrak, skupna dolžina: 6.950 mm, skupna širina: 2.550 mm, skupna višina: 3.500 mm, Leto izdelave: 2018, Oprema: ABS, Bluetooth, centralno zaklepanje, električno nastavljivo ogledalo, električno upravljanje oken, greljenje sedeža, klimatska naprava, nadzor oprijema, retarder, spojka prikolice, tempomat, - Heated mirrors - Digital tachograph - Tachograph (control device) - Fixed - Halogen lamp - Short cab - Manual - PTO (power take-off) - Pump - Radio/cassette - Rear view camera - Lane keeping assist - Seat cover - Central lubrication - Additional brake system Number of axles: 3, Configuration: 6x2, Curb weight: 12,188 kg, Gross weight: 26,000 kg, Total tank volume: 260 liters, Trailer coupling, King pin diameter: 40 mm (DIN), Fifth wheel: Fixed, Number of locks: 1, Central lubrication, Suspension type: Air suspension, Cab type: Short cab, Cruise control, Tachograph (control device), Digital tachograph, Air conditioning, Electric windows, Electric mirrors, Radio/cassette, Color: Anthracite, Heated mirrors, Rear view camera, Lighting: Halogen lamp, Lane keeping assist, Climate control, Seat heating, Bluetooth, Engine power: 338 kW (453 Hp), Fuel: Diesel, Emission standard: Euro 6, Transmission: AS-Tronic, Gearbox make: ZF, Gears: 12, Additional brake system, Retarder make: Intarder, Power steering, ABS, ASR, PTO, PTO type: 1, Starter battery, System type: Meiller AK16, Pump, Central locking, Seating configuration: 1+1, Upholstery: Seat cover, Seat adjustment: Manual, Meiller AK 16 NT Transmission Gearbox: ZF, 12 gears, Automatic Axle configuration Tire size: 315/80R22.5 Brakes: Disc brakes Axle 1: Steering; Tire tread left: 4 mm; Tire tread right: 5 mm; Suspension: Leaf spring Axle 2: Lift axle; Steering; Tire tread left: 11 mm; Tire tread right: 10 mm; Suspension: Air suspension Fpjdpfsx E Ra Sox Ahmoh Axle 3: Twin tires; Tire tread left inner: 12 mm; Tire tread left outer: 10 mm; Tire tread right inner: 12 mm; Tire tread right outer: 11 mm; Suspension: Air suspension Weights Unladen weight: 12,188 kg Payload: 13,812 kg GVW: 26,000 kg Functional Pump: Yes Condition Technical condition: Good Visual condition: Good Damages: None Number of keys: 4 Financial information Lease price: €1,064 per month (default, 60 months); Ask for further details and conditions. Identification Registration number: KLEYN1 Kleyn Trucks is one of the world’s largest independent dealers of used vehicles. Here you can choose from a constantly changing stock of 1,200 used trucks, tractors, and trailers. Our inventory includes all European makes, years of manufacture, and price ranges. Why buy at Kleyn Trucks? Simple! • Large, fast-changing inventory • Recognizable quality • Good pricing • Professional business practices • We speak many languages • We understand our customers • Assistance with import and transport • (Export) registration plates arranged quickly • Expert technical services • The safety of “recognizable quality” • And more... Please visit our website for special offers and the complete stock list. Leasing through Kleyn Trucks is possible in most European countries! Easily calculate your lease rate and submit an inquiry via our website. Ask directly for our European warranty package.