Krauss Maffei Km 150 520 C1 nakup rabljenega (233)

Stanje: zelo dobro (rabljeno), Leto izdelave: 2001, Brizgalni stroj Krauss Maffei KM 800-5000 MC Leto proizvodnje: 2001 Oprema: robot Tehnični podatki: Zapiralna sila: 8 000 kN Največja sila odpiranja orodja: 356 kN Sila pomika gibljive plošče (odpiranje): 98 kN Lsdpsx Tfyiofx Adkori Sila gibljive plošče (zapiranje): 92 kN Velikost plošč (š × v): 1 610 × 1 530 mm Razmak stebrov (š × v): 1 120 × 1 000 mm Hod odpiranja orodja: 1 400 mm Minimalna višina orodja: 600 mm Maksimalno odprtje: 2 000 mm Hod hidravličnega izmetalca: 250 mm Premer polža: 90 mm Razmerje L/D: 23 Tlak vbrizgavanja: 1 742 bar Prostornina vbrizga: 2 863 cm³ Masa vbrizga (PS): 2 605 g Splošni podatki o stroju Dimenzije (d × š × v): 10 500 × 2 860 × 2 890 mm Teža: 43 000 kg

Stanje: rabljeno, Leto izdelave: 2005, Technical details: Lodpfstunccex Adkori Screw diameter: 90 mm Shot weight in polystyrene: 1,758 g/PS (g/polystyrene) Clamping force: 6,500 kN Machine weight approx.: 32 t From series production

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, obratovalne ure: 58.670 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.600 kN, premer vijaka: 45 mm, delovna prostornina: 318 cm³, Clamping force: 1600 kN Max. mold opening force: 87 kN Moving platen opening force: 45 kN Moving platen closing force: 38 kN Mounting platen (H x V): 820 x 845 mm Clearance between tie bars (H x V): 520 x 520 mm Mold opening stroke: 650 mm Min. mold installation height: 300 mm Max. daylight: 950 mm Ejector stroke: 150 mm Ejector force fwd./rev.: 23 kN Injection unit: Screw diameter: 45 mm L/D ratio: 22.4 Injection pressure: 2336 bar Shot volume: 318 ccm Shot weight (PS): 289 g Injection flow: 143 ccm/s Lodoydp Idepfx Adkori Screw speed: 265 rpm Plasticizing rate: 29.3 g/s Nozzle contact force: 50 kN Electrohydraulic equipment: Rated pump motor power: 22 kW Installed heating power: 16 kW Cylinder heater control zones: 5 Oil capacity: 489 ltr. Dimensions and weight: Space requirement approx.: 5.00 x 2.00 x 2.20 m Total weight: 6600 kg Max. mold weight: 1862 kg Accessories: - Vibration isolators - Krauss Maffei Robot LR 100 X: 550 mm Y: 1200 mm Z: 1500 mm C: 0 – 90° Additional equipment: - 1 x air valve - 2 x hydraulic core pulls - 6 x hot runner control zones - Robot interface according to Euromap 67

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, obratovalne ure: 68.590 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.600 kN, premer vijaka: 50 mm, delovna prostornina: 393 cm³, Clamping Force: 1600 kN Max. Tool Opening Force: 87 kN Movable Platen Opening Force: 45 kN Movable Platen Closing Force: 38 kN Clamping Plate (H x V): 820 x 845 mm Clear Distance (H x V): 520 x 520 mm Mould Opening Stroke: 650 mm Min. Mould Installation Height: 300 mm Maximum Opening Width: 950 mm Ejector Stroke: 150 mm Ejector Force Forward/Return: 23 kN Injection Unit: Screw Diameter: 50 mm L/D Ratio: 20 Injection Pressure: 1892 bar Shot Volume: 393 ccm Shot Weight (PS): 358 g Injection Flow Rate: 177 ccm/s Screw Speed: 265 rpm Plasticizing Rate: 36.2 g/s Nozzle Contact Force: 50 kN Electrohydraulic Equipment: Pump Motor Rated Power: 22 kW Installed Heating Capacity: 16 kW Cylinder Heating Control Zones: 5 Oil Capacity: 489 l Dimensions and Weights: Ljdpfx Ajydp D Eedkjri Space Requirement approx.: 5.50 x 2.00 x 2.20 m Total Weight: 6600 kg Max. Mould Weight: 1862 kg Accessories: - Oscillation elements - Krauss Maffei Robot LR 100 X: 550 mm Y: 1200 mm Z: 2500 mm C: 0-90° Additional Equipment: - 1x air valve - 2x core pull - Robot interface according to Euromap 67

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2009, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 6.500 kN, premer vijaka: 70 mm, tlak vbrizgavanja: 2.389 letvica, hod izmetalca: 135 mm, odmični hod: 1.825 mm, TECHNICAL DETAILS Clamping Unit Clamping force: 6,500 kN Maximum mold opening force: 346 kN Moving platen opening force: 169 kN Moving platen closing force: 144 kN Clamping plate dimensions (H x V): 1,520 x 1,470 mm Daylight opening (H x V): 1,000 x 930 mm Mold opening stroke: 1,150 mm Minimum mold installation height: 675 mm Ljdpfx Ajycqc Tedkjri Maximum opening width: 1,825 mm Ejector stroke: 135 mm Ejector force forward/backward: 226 kN Injection Unit Screw diameter: 70 mm L/D ratio: 23 Injection pressure: 2,389 bar Shot volume: 1,097 cm³ Shot weight (PS): 998 g Injection flow rate: 393 cm³/s Screw rotational speed: 218 rpm Plasticizing capacity: 83 g/s Nozzle contact force: 173 kN MACHINE DETAILS Dimensions & Weight Floor space (approx.): 8.70 x 2.90 x 2.80 m Total weight: 44,000 kg Electrohydraulic Equipment Rated pump drive power: 75 kW Installed heating capacity: 36 kW Cylinder heating control zones: 7 FEATURES Oscillating elements 1 x air valve 8-fold pneumatic cascade control Accumulator 2 x hydraulic core pulls on moving platen 2 x hydraulic core pulls on fixed platen Robot interface according to EUROMAP 67

Stanje: zelo dobro (rabljeno), Leto izdelave: 2012, obratovalne ure: 25.000 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 8.500 kN, premer vijaka: 95 mm, delovna prostornina: 3.367 cm³, Clamping force 8500 kN Maximum mold opening force 560 kN Moving platen opening force 153 kN Moving platen closing force 117 kN Mounting platen (h x v) 1600 x 1600 mm Clearance between tie-bars (h x v) 1140 x 1140 mm Mold opening stroke 1600 mm Min./max. mold installation height 500 / 1100 mm Max. opening distance 2100 mm Ejector stroke 300 mm Ejector force forward/backward 200/100 kN Injection unit: Screw diameter 95 mm L/D ratio 23 Injection pressure 1795 bar Lsdpfx Adjyb Sx Hokeri Shot volume 3367 cm³ Shot weight (PS) 3064 g Injection flow rate 690 cm³/s Screw speed 116 rpm Plasticising rate 104 g/s Nozzle contact force 166 kN Electrohydraulic equipment: Pump motor rated power 90 kW Installed heating power 53 kW Number of temperature control zones (barrel heating) 7 Oil capacity 1500 L Dimensions and weights: Required space approx. 11.00 x 3.00 x 2.60 m Total weight 43000 kg Max. mold weight 12200 kg Accessories: - Vibration mounts Additional features: - 1 x air valve - 4 x hydraulic core pulls - 12 x hydraulic cascades - 2 x 12-fold water manifold - Robot interface according to Euromap 67

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036946, vpenjalna sila: 800 kN, premer vijaka: 40 mm, delovna prostornina: 201 cm³, tlak vbrizgavanja: 1.860 letvica, injekcijska masa: 183 g, minimalna višina orodja: 150 mm, izmetalna sila: 22.000 N, hod izmetalca: 100 mm, odmični hod: 750 mm, vgradna višina: 400 mm, skupna dolžina: 4.750 mm, skupna širina: 1.670 mm, skupna višina: 1.850 mm, skupna masa: 5.600 kg, ogrevalna zmogljivost: 11,5 kW (15,64 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 735 mm, teža orodja: 600.000 g, Injection moulding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our certified and versatile stock machines: The base-level injection moulding machine, precisionMolding, represents the perfect entry-level solution for all-electric injection moulding, ensuring fast and innovative responses to market demands. This machine combines high performance, intuitive operation, and short delivery times. It can be utilised in a range of applications such as packaging, electrical and electronics industries, medical technology, and the automotive sector. Your benefits: – Optimised price-performance ratio for a wide range of applications – High energy efficiency thanks to the fully electric machine concept Lrjdpoud H Dmofx Adkei – Fast delivery through a base machine concept with a broad range of options available TECHNICAL DATA: KM 80 / 380 PA G01 (Order 38670023) CONTROL SYSTEM  MC P1 with 15" TFT colour display with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Maximum mould opening force kN 120  Daylight (h x v) mm 470 x 420  Mounting platen (h x v) mm 610 x 560  Mould height min. – max. mm 150 - 400  Maximum opening span mm 750  Maximum mould opening stroke mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force fwd/rev kN 22 / 22  Ejector speed fwd/rev mm/s 300 / 300  Maximum mould weight kg 600 INJECTION UNIT  Screw diameter / type mm 40 / Standard  Effective L/D ratio 20.0  Injection pressure bar 1860  Shot volume cm³ 201  Max. shot weight for PS g 183  Injection speed mm/s 200  Injection flow rate cm³/s 251  Screw drive/speed 1/min 334  Plasticising rate (standard) g/s 24.7  Nozzle contact force kN 34 ELECTRICAL PARAMETERS  Connected load kW 20.6  Installed heating capacity kW 11.5  Power supply V / Hz 400 / 50 3 phase with neutral conductor WEIGHT AND DIMENSIONS  Net weight with control cabinet t 5.6  Length x width x height m 4.75 x 1.67 x 1.85 ADDITIONAL EQUIPMENT  Wear-resistant plasticising unit  BluePower full insulation for plasticising cylinder  Open nozzle  Air valve, single (BWAP)  Pneumatic operation for hot runner shut-off, single  Electrical cascade interface, 4-fold  Euromap interface (handling), E18, E63  Euromap interface (central computer), E67, E77  Water manifold, 4-fold  Automatic central lubrication system  Adaptive Process Control (APC)  Injection-compression moulding circuitry  Graphic analysis package The machine is located at our plant in Parsdorf and is available at short notice. Further optional extras can be offered on request. We look forward to your enquiry.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036940, vpenjalna sila: 1.600 kN, premer vijaka: 50 mm, delovna prostornina: 393 cm³, tlak vbrizgavanja: 1,892 letvica, injekcijska masa: 358 g, minimalna višina orodja: 200 mm, izmetalna sila: 33.000 N, hod izmetalca: 100 mm, odmični hod: 950 mm, vgradna višina: 500 mm, skupna dolžina: 5.650 mm, skupna širina: 1.820 mm, skupna višina: 1.950 mm, skupna masa: 9.700 kg, ogrevalna zmogljivost: 15,5 kW (21,07 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 570 mm, teža orodja: 600.000 g, Injection Moulding Machines Direct from the Manufacturer! As the manufacturer KraussMaffei, we offer you our inspected and flexible stock machines: The entry-level injection moulding machine, precisionMolding, is the perfect solution for fully electric injection moulding, enabling you to respond quickly and innovatively to changing market demands. It combines high performance, easy operation, and short delivery times. The machine is suitable for a wide range of applications, such as the packaging industry, electronics and electrical industry, medical technology, and the automotive sector. Your benefits: – Optimized price-performance ratio for a broad range of applications – High energy efficiency thanks to a fully electric machine concept – Reliable and efficient delivery times due to a base machine concept with a wide spectrum of options TECHNICAL DATA: KM 160 / 750 PA G01 (Order 38670011) (Machine No.: 61036683, new, year 2013) CONTROL SYSTEM - MC P1 with 15" TFT colour display with multi-touch functions CLAMPING UNIT - Clamping force: 1600 kN - Maximum mould opening force: 120 kN - Daylight (H x V): 570 x 520 mm - Mounting platen (H x V): 770 x 720 mm - Mould installation height min. – max.: 200 – 500 mm - Maximum opening width: 950 mm - Maximum mould opening stroke: 450 mm Ljdjugfw Dopfx Adkjri - Ejector drive: electric - Ejector stroke: 100 mm - Ejector force, forward/reverse: 33 / 33 kN - Ejector speed, forward/reverse: 300 / 300 mm/s - Maximum mould weight: 1200 kg INJECTION UNIT - Screw diameter / type: 50 mm / standard - Effective L/D ratio: 20.2 - Injection pressure: 1,892 bar - Stroke volume: 393 cm³ - Shot weight at max. stroke for PS: 358 g - Injection speed: 200 mm/s - Injection flow rate: 393 cm³/s - Screw drive / rotation speed: 267 rpm - Plasticizing throughput (standard screw): 36.5 g/s - Nozzle contact force: 42 kN ELECTRICAL PARAMETERS - Connected load: 31.2 kW - Installed heating capacity: 15.5 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral WEIGHT AND DIMENSIONS - Net weight (incl. control cabinet): 9.7 t - Length x width x height: 5.65 x 1.82 x 1.95 m ADDITIONAL FEATURES - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - Air valve, single (BWAP) - Pneumatic control for hot runner shut-off, single - Electrical interface for pneumatic cascade, 4-fold - Euromap interface for handling: E18 + E67 - Euromap interface (central computer): E67, E77 - Water manifold, 4-fold - Electrical pre-installation for hydraulic auxiliary unit - Automatic central lubrication - Adaptive Process Control (APC) - Injection compression moulding circuit - Graphic analysis package - Swivel device for injection unit The machine is located at our facility in Parsdorf and is available at short notice. Additional options can be offered upon request. We look forward to your enquiry.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036683, vpenjalna sila: 1.600 kN, premer vijaka: 50 mm, delovna prostornina: 393 cm³, tlak vbrizgavanja: 1,892 letvica, injekcijska masa: 358 g, minimalna višina orodja: 200 mm, izmetalna sila: 33.000 N, hod izmetalca: 100 mm, odmični hod: 950 mm, vgradna višina: 500 mm, skupna dolžina: 5.650 mm, skupna širina: 1.820 mm, skupna višina: 1.950 mm, skupna masa: 9.700 kg, ogrevalna zmogljivost: 15,5 kW (21,07 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 570 mm, teža orodja: 600.000 g,

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61037337, vpenjalna sila: 800 kN, premer vijaka: 30 mm, delovna prostornina: 113 cm³, tlak vbrizgavanja: 2.500 letvica, injekcijska masa: 103 g, minimalna višina orodja: 400 mm, izmetalna sila: 22.600 N, hod izmetalca: 150 mm, odmični hod: 900 mm, skupna dolžina: 3.960 mm, skupna širina: 1.480 mm, skupna višina: 2.020 mm, skupna masa: 3.550 kg, ogrevalna zmogljivost: 10,9 kW (14,82 KM), vrsta pogona: Hadraulisch, prosta razpetina: 470 mm, teža orodja: 1.000.000 g,

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036936, vpenjalna sila: 800 kN, premer vijaka: 35 mm, delovna prostornina: 135 cm³, tlak vbrizgavanja: 1.837 letvica, injekcijska masa: 123 g, minimalna višina orodja: 150 mm, izmetalna sila: 22.000 N, hod izmetalca: 100 mm, odmični hod: 750 mm, vgradna višina: 400 mm, skupna dolžina: 4.750 mm, skupna širina: 1.670 mm, skupna višina: 1.820 mm, skupna masa: 5.900 kg, ogrevalna zmogljivost: 8,9 kW (12,10 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 470 mm, teža orodja: 600.000 g, Injection moulding machines directly from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines: The base injection moulding machine, precisionMolding, is the perfect entry-level solution for all-electric injection moulding, enabling rapid and innovative responses to market requirements. It combines high performance, user-friendly operation, and short delivery times. The machine can be used across various application areas, such as the packaging industry, electrical and electronics industry, medical technology, and the automotive sector. Your benefits: – Optimised price-performance ratio for a wide range of applications – High energy efficiency thanks to the all-electric machine concept – Fast delivery times realised through basic machine concept with a broad spectrum of options TECHNICAL DATA: KM 80 / 250 PA G01 (Order 38670013) (Machine no.:61036936, new, Year 2023) CONTROL SYSTEM • MC P1 with 15" TFT colour display and multi-touch function CLAMPING UNIT • Clamping force kN 800 • Maximum mould opening force kN 120 • Daylight (h x v) mm 470 x 420 • Mounting platens (h x v) mm 610 x 560 • Minimum - maximum mould height mm 150 - 400 • Maximum opening stroke mm 750 • Maximum mould opening travel mm 350 • Ejector drive electric • Ejector stroke mm 100 • Ejector force forward/back kN 22 / 22 • Ejector speed forward/back mm/s 300 / 300 • Maximum mould weight kg 600 INJECTION UNIT • Screw diameter / type mm 35 / standard • Effective L/D ratio 20.0 • Injection pressure bar 1837 • Stroke volume cm³ 135 • Shot weight at max. stroke (PS) g 123 • Injection speed mm/s 200 • Injection flow rate cm³/s 192 • Screw drive / speed 1/min 382 • Plastification rate (standard screw) g/s 19.5 • Nozzle contact force kN 30 ELECTRICAL PARAMETERS • Connected load kW 17.8 • Installed heating capacity kW 8.9 • Power supply V / Hz 400 / 50, 3-phase with neutral WEIGHT AND DIMENSIONS • Net weight with control cabinet t 5.9 • Length x Width x Height m 4.75 x 1.67 x 1.82 ADDITIONAL EQUIPMENT • Wear-resistant plastification • BluePower full insulation of plastification cylinder • Open nozzle • Air valve, single (BWAP) • Pneumatic control for hot runner shut-off, single Lredpfeuggb Dsx Adkei • Electrical interface (cascade), 4-fold • Electrical preparation for hydraulic auxiliary unit • Euromap interface for handling, E18, E63 • Euromap interface (central computer), E67, E77 • Water manifold, 4-fold • Automatic central lubrication • Adaptive Process Control (APC) • Injection-compression moulding function • Graphics analysis package • Swivelling device for injection unit The machine is located at our factory in Parsdorf and is available at short notice. Additional optional features can be offered on request. We look forward to your enquiry.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036721, vpenjalna sila: 6.500 kN, premer vijaka: 70 mm, razmak između stupova: 1.110 mm, delovna prostornina: 1.078 cm³, tlak vbrizgavanja: 1.877 letvica, injekcijska masa: 981 g, odmični hod: 3.200 mm, višina plošče: 1.540 mm, vrsta pogona: Hydraulisch, prosta razpetina: 3.200 mm, teža orodja: 2.200.000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and versatile stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX guide shoe, forces are optimally absorbed and the service life of your molds is increased. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly, and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM • MC 6 with 24" TFT color display featuring multitouch functions CLAMPING UNIT • Clamping force kN 6500 • Max. mold opening force kN 455 • Clear width (h x v) mm 1110 x 960 • Mounting platen (h x v) mm 1540 x 1440 • Mold installation height, min. - max. mm 1550 (without center plate) • Max. opening stroke mm 3200 • Max. mold opening path mm 1650 • Max. mold weight kg 22000 INJECTION UNIT 1 SP2000 • Screw diameter/type mm 60 / Thermoplastic • Effective L/D ratio 23.3 • Injection pressure bar 2420 • Shot volume cm³ 792 • Shot weight at max. stroke for PS g 720 • Injection speed mm/s 140 • Injection flow cm³/s 396 • Screw drive/rotation speed 1/min 285 • Plasticizing flow g/s 72.2 • Nozzle contact force kN 82 INJECTION UNIT 2 SP2000 • Screw diameter/type mm 70 / Thermoplastic • Effective L/D ratio 20 • Injection pressure bar 1877 • Shot volume cm³ 1078 • Shot weight at max. stroke for PS g 981 • Injection speed mm/s 140 • Injection flow cm³/s 539 • Screw drive/rotation speed 1/min 285 • Plasticizing flow g/s 98.3 • Nozzle contact force kN 82 ELECTRICAL PARAMETERS Connected load kW 341 • Power supply V/Hz 400/50 (3 phases with neutral conductor) WEIGHT AND DIMENSIONS • Net weight t 43.5 • Length x width x height m 11.89 x 3.22 x 2.77 ADDITIONAL EQUIPMENT • Wear-resistant plasticizing unit • BluePower full insulation for plasticizing cylinder • Open nozzle • BluePower ServoDrive • Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) • Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) • Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) • Mold heating: 96-fold (3.5 kW) • Euromap interface for handling: E18 • Euromap interfaces (mainframe): E67, E77, E78, E63, E82.1 • Adaptive Process Control (APC+) • Graphic analysis package • Sliding table with turning unit, servo-driven • Vertical center plate • Parallel closing and opening pressing during the injection process with parallelism control between FWAP and center plate or BWAP and center plate • ColorForm interface: signal interface for integration of an RPM system • Electrical interface for HRS Flexflow system • Electrical interface and hydraulic valves for "1-K dummy operation" • Interface for connection of a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our Parsdorf facility and is available at short notice. Additional options can be offered on request. Ljdpfew U N Ixex Adkeri We look forward to your inquiry.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2004, Krauss Maffei Injection Moulding Machine KM 350-2700 C2+ Year of manufacture: 2004 System: Fully hydraulic Control: MC4, color monitor, integrated control panel, built-in floppy disk drive 2. Plasticizing Unit Complete plasticizing unit for thermoplastics Version with abrasion protection Screw diameter: 80 mm Non-return valve Open nozzle TECHNICAL DATA Clamping Unit Clamping force: 3500 kN Mold opening force: 220 kN Movable platen stroke force: - opening: 105 kN - closing: 95 kN Platen size (H × V): 1060 × 1095 mm Tie bar clearance (H × V): 710 × 710 mm Mold opening stroke: 920 mm Mold installation height: 380 mm Daylight opening: 1300 mm Ejector stroke: 250 mm Ejector force: 95 / 48 kN Injection Unit Screw diameter: 80 mm Injection pressure: 1829 bar Shot volume: 1433 cm³ Shot weight for PS: 1304 g Screw speed (standard/option): 218 / 284 rpm Lsdpfjx Elukex Adkjri Injection rate: 1508 cm³/s Output at standard speed: 108 g/s Output at increased speed: 141 g/s Electro-hydraulic Equipment Pump motor power: 75 kW Installed heater capacity: 36 kW Number of heating zones (barrel): 7 Dry cycle time according to Euromap: 1550 1/h Oil tank capacity: 720 l Dimensions and weight Net weight (with control cabinet): 16.7 t Machine dimensions (L × W × H): 6.91 × 2.04 × 2.41 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, Krauss Maffei Injection Moulding Machine KM 110–750 CX Year of manufacture – 2007 Fully hydraulic clamping system. MC5 control with a colour monitor, integrated operator panel, and 3 USB ports. Plasticising Unit Complete plasticising unit for thermoplastics Version with abrasion protection Screw diameter: 40 mm Non-return valve Open nozzle TECHNICAL DATA Clamping Unit Clamping force: 1100 kN Mould opening force: 70 kN Movable platen force: - Opening: 35.4 kN - Closing: 31.4 kN Platen dimensions (h × v): 745 × 770 mm Tie bar spacing (h × v): 470 × 470 mm Mould opening stroke: 600 mm Minimum mould height: 300 mm Platen opening stroke: 900 mm Ejector stroke: 150 mm Ejector force: 22.6 / 9.9 kN Ledjx Avhyspfx Adkeri Injection Unit Screw diameter: 40 mm Injection pressure: 2500 bar Shot volume: 251 cm³ Shot weight (PS): 228.41 g Screw rotation speed (standard/option): 295 / 355 rpm Electrical & Hydraulic Equipment Pump motor rated power: 22 kW Installed heater power: 15.62 kW Number of cylinder heating zones: 5 Dry cycles per Euromap: 2000 cycles/h Oil tank capacity: 489 l Dimensions and Weight Net weight with control cabinet: 6.2 t Machine dimensions (L × W × H): 4.9 × 1.6 × 2.1 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2010, Brizgalni stroj Krauss Maffei KM 80-380 CX Leto izdelave: 2010 Enota za zapiranje Zapiralna sila: 800 kN Dimenzije vpenjalnih plošč (V × Š): 670 × 670 mm Prostor med stebri (V × Š): 420 × 420 mm Višina orodja (min./maks.): 250 mm Maksimalna odprtina: 750 mm Vbrizgalna enota Premer polža: 40 mm Volumen vbrizga: 201 cm³ Masa vbrizga (PS): 183 g Tlak vbrizga: 1860 bar Lrodpfx Adjxw Upfekoi Elektro-hidravlična oprema Moč črpalnega motorja: 15 kW Moč grelcev: 10,9 kW Dimenzije in teža Dimenzije stroja (d × š × v): 4,09 × 1,48 × 2,02 m Teža (z električno omaro): 3,55 t

Stanje: novo, Leto izdelave: 2025, Injection Moulding Machine – Krauss Maffei KM 160-750 CX Year of manufacture: 2025 Fully hydraulic clamping system. MC 6 control system based on an industrial computer with real-time Ethernet technology, equipped with an integrated 21.5" operator panel featuring a colour touchscreen display. Plasticizing Unit Complete plasticizing unit for thermoplastics, screw diameter 50 mm, with non-return valve and open nozzle Nozzle radius: 10 mm Nozzle opening: 4 mm Technical Specifications (Standard Version) Clamping Unit Clamping force: 1,600 kN Opening force: 86 kN Platen dimensions (H x V): 820 x 845 mm Tie bar spacing (H x V): 520 x 520 mm Opening stroke: 650 mm Minimum mould height: 300 mm Maximum daylight: 950 mm Ejector stroke: 150 mm Ejector force, forward/reverse: 23 / 10 kN Injection Unit Screw diameter: 50 mm L/D ratio: 20.2 Injection pressure: 1,892 bar Lodsxdd N Uspfx Adkori Injection volume: 393 cm³ Shot weight (PS): 357 g Injection speed: 90 mm/s Injection rate (standard): 177 cm³/s Screw speed (standard): 265 rpm Electro-hydraulic System Pump drive power: 22 kW Installed heating capacity: 15.5 kW Dry cycle time according to Euromap 6: 2.1 s Oil tank capacity: 400 l Linear Robot – Krauss-Maffei LRX 100 Payload < 10 kg (gripper + drives + parts) Part removal on operator-off side Axes: X-axis (from mould): 620 mm, servo motor Y-axis (vertical, with motor brake): 1200 mm, servo motor Z-axis (crosswise): 1500 mm, servo motor Dimensions and Weight Net weight (with control cabinet): 6.10 t Machine dimensions (L x W x H): 4.93 x 1.62 x 2.04 m

Stanje: novo, Leto izdelave: 2025, Injection Moulding Machine – Krauss Maffei KM 300-1400 CX Year of manufacture: 2025 Fully hydraulic clamping system. MC 6 control system based on an industrial computer with real-time Ethernet technology, equipped with an integrated 21.5" operator panel with full-colour touchscreen. Plasticizing unit Complete plasticizing unit for thermoplastics, screw diameter 60 mm, with non-return valve and open nozzle Nozzle radius: 15 mm Nozzle orifice: 6 mm Technical data (standard version) Clamping unit Clamp force: 3,000 kN Opening force: 169 kN Platen dimensions (H x V): 995 x 1,050 mm Tie bar spacing (H x V): 630 x 630 mm Opening stroke: 820 mm Minimum mould height: 330 mm Maximum daylight: 1,150 mm Ejector stroke: 200 mm Ejector force front/rear: 58 / 28 kN Injection unit Screw diameter: 60 mm L/D ratio: 20.8 Lsdpfx Aoxdd Spjdkori Injection pressure: 2,006 bar Shot volume: 679 cm³ Shot weight (PS): 618 g Injection speed: 110 mm/s Standard injection rate: 311 cm³/s Standard screw speed: 260 rpm Electro-hydraulic system Pump motor power: 45 kW Installed heater power: 22.4 kW Dry cycle time according to Euromap 6: 2.7 s Oil tank capacity: 720 l Linear robot – Krauss-Maffei LRX 150 Payload < 15 kg (gripper + drives + parts) Part release on operator-opposite side Axes: X axis (from mould): 900 mm, servomotor Y axis (vertical, with motor brake): 750/750 mm, servomotor, telescopic Z axis (transverse): — Dimensions and weight Net weight (with control cabinet): 13.2 t Machine dimensions (L x W x H): 6.16 x 2.17 x 2.26 m

Stanje: novo, Leto izdelave: 2025, Injection Moulding Machine – Krauss Maffei KM 651-6100 GX Year of manufacture: 2025 Hydraulic-mechanical, two-platen clamping system with four pressure pads on the fixed platen and four locking units on the moving platen. PV – injection unit control. MC6 control system based on an industrial PC using real-time Ethernet technology, equipped with an integrated 21.5” operator panel with a color touchscreen display. Lrodoxdd U Depfx Adksi Plasticizing System Complete plasticizing unit for thermoplastics, screw diameter 95 mm, with non-return valve and open nozzle. Nozzle radius: 25 mm Nozzle opening: 9 mm Technical Specifications (standard version) Clamping Unit Clamping force: 6500 kN Opening force: 455 kN Platen dimensions (H x V): 1660 x 1530 mm Tie-bar spacing (H x V): 1200 x 1020 mm Opening stroke: 1450 mm Mould height (min.–max.): 450 – 1000 mm Daylight: 1900 mm Ejector stroke: 300 mm Ejector force, forward/back: 140 / 70 kN Injection Unit Screw diameter: 95 mm L/D ratio: 23.0 Injection pressure: 1795 bar Shot volume: 3367 cm³ Shot weight (PS): 2391 g Injection speed: 110 mm/s Injection capacity: 780 cm³/s Screw speed (standard): 147 rpm Plasticizing rate (at standard speed): 102 g/s Nozzle contact force: 166 kN Electro-hydraulic System Pump motor power: 97 kW Installed heater power: 54 kW Number of barrel heating zones: 7 Dry cycle time (per Euromap 6): 3.3 s / 840 mm Dry cycle time (KM standard): 2.9 s / 600 mm Oil tank capacity: 1435 l Linear Robot – Krauss-Maffei LRX 250 Payload < 25 kg (gripper + drives + parts) Part placement on operator-opposite side Axes: X axis (from mould): 900 mm, servomotor Y axis (vertical, telescopic, with motor brake): 1000/1000 mm, servomotor Z axis (crosswise): 2500 mm, servomotor Dimensions and Weight Net weight (with control cabinet): 38.5 t Machine dimensions (L x W x H): 10.19 x 3.03 x 2.51 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2011, Krauss Maffei KM 850-12000 MX Injection Moulding Machine Year of manufacture: 2011 LRX 500 Robot Z-axis: 4000 mm X-axis: 1500 mm Y-axis: 1250/1250 mm Hydraulic-mechanical, two-platen clamping system with 4 pressure pads and 4 locking units on the movable platen. PV - injection unit control adjustment. MC 5 control system with colour monitor, integrated control panel and USB data carrier. Plasticising unit: Complete plasticising unit for thermoplastics with a 135 mm screw diameter, non-return valve and open nozzle. Nozzle radius: 25 mm, nozzle orifice: 9 mm TECHNICAL DATA Clamping Unit - Clamping force: 8,500 kN - Mould opening force: 560 kN - Platen dimensions (H x V): 1600 x 1600 mm - Tie bar clearance (H x V): 1140 x 1140 mm - Mould opening stroke: 1600 mm - Mould height (min-max): 500 - 1100 mm - Daylight: 2100 mm - Ejector stroke: 300 mm - Ejector force: 200 / 100 kN Injection Unit - Screw diameter: 135 mm - Injection pressure: 1,389 bar - Injection volume: 8,588 cm³ - Shot weight for PS: 6,098 g - Injection rate: 1,414 cm³/s Electro-hydraulic equipment - Rated pump motor power: 132 kW - Dry cycle time according to Euromap 6: 965 1/h - Oil tank capacity: 2,440 l Weight and dimensions Lrsdpfxjwqdyij Adkei - Net weight with control cabinet: 49 t - Installation space (L x W x H): 11.72 x 2.92 x 2.71 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2015, Krauss Maffei KM 900 – 8100 GX Injection Moulding Machine Year of manufacture: 2015 General Description: Hydro-mechanical, two-platen clamping system with 4 pressure pads on the fixed platen and 4 control units on the movable platen. The machine is equipped with a PV (proportional valve) injection unit regulation system. Control is provided by a modern MC6 system, based on an industrial PC with real-time Ethernet technology. The control panel features an integrated 19-inch touchscreen with a colour display, LED backlighting, and full process visualisation via ProcessDesigner. Plasticising unit: Complete system for thermoplastics processing Wear-resistant (abrasion-proof) version Screw diameter: 105 mm Shut-off valve and open nozzle Technical specifications: Clamping unit: Clamping force: 9,000 kN Mould opening force (pressure pads): 630 kN Platen dimensions (W x H): 1660 x 1530 mm Tie bar spacing: 1180 x 1000 mm Max. mould opening stroke: 1600 mm Mould height (min – max): 500 – 1100 mm Maximum opening stroke: 2100 mm Ejector stroke: 300 mm Ejector force (forward / return): 140 / 70 kN Injection unit: Screw diameter: 105 mm L/D ratio: 23.0 Injection pressure: 1778 bar Injection volume: 4546 cm³ Shot weight (for PS): 3228 g Injection rate: 805 cm³/s Screw speed (standard): 150 rpm Nozzle touch force: 166 kN Electrical-hydraulic equipment: Pump motor power: 120 kW Heater power: 59 kW Number of barrel heating zones: 7 Dry cycle time / stroke (Euromap 6): 3.3 s / 826 mm Dry cycle time / stroke (KM standard): 2.9 s / 590 mm Oil tank capacity: 1450 l Dimensions and weight: Net weight (incl. control cabinet): 40 tonnes Ledowyxbgopfx Adkeri Machine dimensions (L x W x H): 10.72 x 3.03 x 2.51 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2004, Krauss Maffei KM 2300 - 12000 MC Injection Moulding Machine Year: 2004 Control system: MC 4 Operating hours: 93,900 Clamping Unit Clamping force: 23,000 kN Maximum mould opening force: 1,420 kN Moving platen force - Opening: 227 kN Moving platen force - Closing: 203 kN Lrjdpfxowq Ed Ae Adksi Platen size (H x V): 2,830 mm x 2,400 mm Tie-bar spacing (H x V): 2,000 mm x 1,600 mm Mould opening stroke: 2,600 mm Minimum mould height: 1,100 mm Maximum mould height: 1,800 mm Maximum daylight: 3,700 mm Hydraulic ejector stroke: 350 mm Ejector force forward/backward: 415/115 kN Injection Unit Screw diameter: 135 mm Ls/D ratio: 23 Injection pressure: 1,389 bar Shot volume: 8,588 ccm Injection weight, PS: 7,815 g Injection rate: 1,019 ccm/s Screw speed: 113 rpm Max. plasticising rate: 191 g/s Nozzle pressure: 241 kN Electrical and Hydraulic Equipment Pump drive capacity: 132 kW Installed heating power: 997 kW Adjustable barrel heating zones: 7 Drying cycles per hour: 350 Tank capacity: 2,500 litres Dimensions and Weight Machine dimensions: 15.15 m x 4.15 m x 3.29 m Total machine weight: 143,000 kg Max. mould weight: 62,000 kg LRX 1000 Robot X-axis: 2,000 mm Y-axis: 3,000 mm Z-axis: 5,000 mm

Stanje: dober (rabljeno), Leto izdelave: 2011, Krauss Maffei Injection Moulding Machine KM 850-12000 MX With Krauss Maffei robot Year of manufacture: 2011 Hydraulic-mechanical two-platen clamping system with 4 pressure pads and 4 locking units on the moving platen. PV - injection unit stroke control. MC 5 control system with colour monitor, integrated control panel, and USB data carrier. Plasticizing unit Complete plasticizing unit for thermoplastics with screw diameter 135 mm, with non-return valve and open nozzle. Nozzle radius 25 mm, nozzle orifice 9 mm TECHNICAL DATA Clamping unit - Clamping force: 8500 kN - Opening force: 560 kN - Mounting platen dimensions (h x v): 1600 x 1600 mm - Tie bar clearance (h x v): 1140 x 1140 mm - Opening stroke: 1600 mm - Mould height (min-max): 500 - 1100 mm - Daylight: 2100 mm - Ejector stroke: 300 mm - Ejector force: 200 / 100 kN Injection unit - Screw diameter: 135 mm Ledpstrya Refx Adkori - Injection pressure: 1389 bar - Shot volume: 8588 cm³ - Shot weight for PS: 6098 g - Injection rate: 1414 cm³/s Electro-hydraulic equipment - Rated motor power (pump): 132 kW - Dry cycle time according to Euromap 6: 965 1/h - Oil tank capacity: 2440 l Weight and dimensions - Net weight with control cabinet: 49 t - Installation space (L x W x H): 11.72 x 2.92 x 2.71 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2011, Krauss Maffei Injection Molding Machine KM 850-12000 MX With Krauss Maffei LRX 500 Robot Year of manufacture – 2011 Hydraulic-mechanical two-platen clamping system with 4 pressure pads and 4 locking units on the moving platen. PV – injection unit adjustment. MC 5 control system with color monitor, integrated control panel, and USB data carrier. Plasticizing Unit Complete plasticizing unit for thermoplastics with 135 mm screw diameter, shut-off nozzle and open nozzle. Nozzle radius 25 mm, nozzle opening 9 mm TECHNICAL DATA Clamping Unit - Clamping force: kN 8500 - Mold opening force: kN 560 - Platen dimensions (H x V): mm 1600 x 1600 - Tie bar spacing (H x V): mm 1140 x 1140 - Mold opening stroke: mm 1600 - Mold height (min-max): mm 500 - 1100 - Daylight: mm 2100 - Ejector stroke: mm 300 - Ejector force: kN 200/100 Injection Unit Ljdpfx Adjwkhmmoksri - Screw diameter: mm 135 - Injection pressure: bar 1389 - Shot volume: cm³ 8588 - Shot weight for PS: g 6098 - Injection rate: cm³/s 1414 Electro-hydraulic Equipment - Pump motor rated power: kW 132 - Dry cycle time as per Euromap 6: 1/h 965 - Oil tank capacity: l 2440 Weight and Dimensions - Net weight with control cabinet: t 49 - Installation dimensions (L x W x H): m 11.72 x 2.92 x 2.71

Stanje: zelo dobro (rabljeno), Leto izdelave: 2008, Krauss Maffei KM 300-1000 CX Injection Moulding Machine Year of manufacture: 2008 Manufacturer: Krauss Maffei Control system: MC 5 with colour monitor, integrated control panel, and disk station Clamping system: Fully hydraulic Plasticising Unit SP 1000 Screw diameter: 50 mm Non-return valve, open nozzle Nozzle radius: 15 mm, opening: 3 mm Clamping Unit Clamping force: 3000 kN Opening force: 169 kN Platen dimensions (H × V): 995 × 1050 mm Tie bar spacing: 630 × 630 mm Mould opening stroke: 820 mm Minimum mould height: 330 mm Max. daylight: 1150 mm Ejector stroke: 200 mm Ejector force (forward/back): 58 / 28 kN Injection Unit Screw diameter: 50 mm L/D ratio: 22.0 Injection pressure: 2304 bar Shot volume: 432 cm³ Shot weight (PS): 393 g Injection speed: 170 mm/s Injection flow rate: 334 cm³/s Screw speed (standard): 370 rpm Plasticising capacity (at standard rpm): 54.3 g/s Electro-hydraulic Equipment Pump motor power: 45 kW Heater power: 18.7 kW Number of heating zones: 5 Dry cycle time / stroke according to Euromap 6: 2.8 s / 441 mm Oil tank capacity: 720 l Dimensions and Weight Lrjdpfow U Rcdex Adksi Net weight (with control cabinet): 12.5 t Dimensions (L × W × H): 6.11 × 2.17 × 2.25 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 2002, Krauss Maffei KM 420-2700 C2 Injection Moulding Machine Year of manufacture: 2002 Machine Description The Krauss Maffei KM 420-2700 C2 injection moulding machine is a robust and precise machine with a high clamping force of 4200 kN, designed for processing thermoplastic materials. Equipped with a reliable hydraulic system and a precise control system, it ensures stable and repeatable operation in demanding production environments. Technical Specifications Clamping Unit Parameter Unit Value Clamping force kN 4200 Max. mould opening force kN 250 Movable platen traverse force – opening kN 124 Movable platen traverse force – closing kN 102 Platen dimensions (H × L) mm 1270 × 1200 Tie bar clearance (H × L) mm 800 × 800 Mould opening stroke mm 1020 Minimum mould height mm 380 Maximum daylight mm 1400 Ejector force (forward / backward) kN 95 / 48 Max. mould weight kg 6700 Injection Unit Parameter Unit Value Screw diameter mm 70 L/D ratio - 20 Injection pressure bar 1829 Shot volume cm³ 1097 Shot weight (PS) g 998 Injection rate cm³/s 513 Max. plasticizing rate g/s 108 Nozzle pressure kN 173 Electrical and Hydraulic Equipment Parameter Unit Value Rated pump motor power kW 75 Installed heating power kW 36 Number of heating zones (barrel) - 7 Oil tank capacity l 1075 Lodpfxoxq Akkj Adkjri Dimensions and Weight Parameter Unit Value Machine dimensions (L × W × H) m 7.06 × 2.33 × 2.51 Total machine weight kg 20,500