Tiskalnice za ohišja nakup rabljenega (39)

Stanje: rabljeno, Leto izdelave: 1998, Rabljeni stroj Leto izdelave: 1998 Oprema in tehnični podatki: - Dolžina stiskanja: maks. 2500 mm - Višina stiskanja: maks. 1350 mm Fpedpfx Akezhc H Hswsi - Delovna globina: maks. 600 mm - Čas stiskanja: nastavljiv - Vertikalni in horizontalni stiskalni nosilci se pomikajo elektromehansko in so med seboj zobato povezani - Ustvarjanje tlaka preko frekvenčno krmiljenih reduktorskih motorjev - Stiskalni tlak je za vertikalo in horizontalo nastavljiv posebej - Dimenzije: pribl. 370 x 100 x 225 cm - Teža: pribl. 2.100 kg Razpoložljivost: kratkoročno Lokacija skladišča: 63934 Röllbach

Stanje: rabljeno, Leto izdelave: 1992, Mere: 5700 x 1300 x 2400 mm Skladišče: Nattheim Fpodjvvkl Depfx Akwei

Stanje: rabljeno, Leto izdelave: 2003, Rabljen stroj Letnik izdelave: 2003 Oprema in tehnični podatki: - prilagodljiva, pnevmatska preša z zelo kratkim časom nastavitve - preša je sestavljena iz robustnega okvirja preše in preprosto premikajoče se prešalne vozice - ter horizontalnih in vertikalnih prešnih plošč - vsi upravljalni elementi so enostavno dosegljivi - preša MPH 100 pri prešanju povzroča blokiranje prešalne vozice – podobno kot pri vpenjalnem mehanizmu - s 3 navpičnimi prešnimi ploščami - z 2 vodoravnimi prešnimi ploščami - dolžina ohišja: 380 – 2500 mm - največja globina ohišja: 600 mm Fedpsy Ih Ryjfx Akwjpi - višina ohišja: 350 – 1200 mm - pritisk preše: 3,6 kN/prešna plošča - delovna višina: 600 mm - teža: 1,1 tone - delovni tlak: 6 bar Razpoložljivost: v kratkem času Lokacija skladišča: 63934 Röllbach

Stanje: rabljeno, Leto izdelave: 1998, Rabljen stroj Letnik izdelave: 1998 Oprema in tehnični podatki: - Dolžina stiskanja: največ 2500 mm Fpodszk N Uispfx Akwji - Višina stiskanja: največ 1350 mm - Globina delovanja: največ 600 mm - Čas stiskanja: nastavljiv - Vertikalna in horizontalna stiskalna palica se premikata elektromehansko in se vpetata druga v drugo - Ustvarjanje tlaka s frekvenčno uravnanimi pogonskimi motorji - Tlak stiskanja je vertikalno in horizontalno nastavljiv ločeno - Dimenzije: približno 370 x 100 x 225 cm - Teža: približno 2100 kg Razpoložljivost: v kratkem času Lokacija: 63934 Röllbach primerno starosti

Stanje: rabljeno, Leto izdelave: 2003, Rabljen stroj Letnik izdelave: 2003 Fsdpfjzk N Naox Akwjpi Oprema in tehnični podatki: - fleksibilna, pnevmatska stiskalnica z zelo kratkim časom priprave - stiskalnica je sestavljena iz robustnega okvirja in enostavno premikajoče se stiskalne plošče - ter horizontalnih in vertikalnih stiskalnih plošč - vsi elementi upravljanja so lahko dostopni - model MPH 100 pri stiskanju zagotavlja, da se stiskalna plošča zatakne – podobno kot pri vpenjalnem mehanizmu - s 3 navpičnimi stiskalnimi ploščami - z 2 vodoravnimi stiskalnimi ploščami - dolžina ohišja: 380–2500 mm - največja globina ohišja: 600 mm - višina ohišja: 350–1200 mm - pritisk: 3,6 kN na stiskalno ploščo - delovna višina: 600 mm - teža: 1,1 tone - delovni tlak: 6 bar Razpoložljivost: kratkoročno Lokacija: 63934 Röllbach Dobro ohranjeno.

Stanje: dober (rabljeno), Samo-centrično elektronsko prehodno vpenjalo Krmiljenje NC400 Dimenzije pohištva: Dolžina od najmanj 250 mm do največ 2500 mm Širina (globina) od 180 mm do 780 mm Fpsdpfx Ajzfpulokwsi Višina najmanj 300 mm, največ 1300 mm

Stanje: zelo dobro (rabljeno), Leto izdelave: 1993, številka stroja/vozila: 221/93, Funkcionalnost: popolnoma funkcionalen, Connected load 380V 16A Pneumatic connection 6 bar Fsdpfxjk Tzwds Akwepi Total machine length 4300 mm Total machine width 1300 mm Maximum pressing length 2650 mm Pressing width 1000 mm Pressing height 1000 mm Pressing pressure up to 150 bar Electric width adjustment with digital display Foot switch for pressing

Stanje: rabljeno, Stisne mere: ca. 2500 x 1200 x 600 mm, polhidravlično, elektromotorno nastavljanje stisne stene Fodpfx Aezd Hm Nekwepi Lokacija skladiščenja: Nattheim

Stanje: dober (rabljeno), Leto izdelave: 2013, Funkcionalnost: popolnoma funkcionalen, moč: 5 kW (6,80 KM), Avtomatska pretočna korpusna stiskalnica z elektronsko nastavitvijo tlačnih sil, časovanjem in programiranim zaporedjem zapiranja stiskalnih plošč. Proizvajalec: SCM Group (divizija CPC) Model: Action TF2500 Letnik: 2013 Stanje stroja: popolnoma funkcionalen Glavne tehnične specifikacije: - maks. dimenzije korpusa: 2500 x 1250 x 650 mm - min. dimenzije korpusa: 250 x 250 x 250 mm - hitrost transportnega traku: 20 m/min - delovna višina: 600 mm Fedpfszgtg Iex Akwepi - dolžina vhodnega transporterja: 2500 mm - dolžina izhodnega transporterja: 2500 mm - skupna priključna moč: 5 kW (15A) Funkcionalnost: Samodejno zaznavanje dimenzij vhodne omare, vključno z avtomatsko detekcijo prisotnosti sredinske prečke. Programator: - upravljalna plošča z zaslonom na dotik (14 cm diagonala) - uporabniški vmesnik v slovenščini - nastavitev vodoravnega pritiska (0-1300 kg) - nastavitev navpičnega pritiska (0-1300 kg) - izbira stiskalnega postopka (zgornji pritiskač, bočni pritiskač, zgornji/bočni pritiskač) - nastavitev položaja vodoravnih sredinskih pritiskačev

Stanje: rabljeno, Leto izdelave: 2003, številka stroja/vozila: 0-306-04-2737, delovna širina: 800 mm, dolžina transportnega traku: 4.800 mm, hitrost pomika os X: 37 m/min, delovna višina: 1.400 mm, delovna dolžina: 2.300 mm, Nižja cena ni določena - zagotovljena prodaja najvišjemu ponudniku! Prevzem stroja mora biti opravljen med 10. 06. 26 in 30. 06. 26! TEHNIČNI PODATKI Maksimalna širina obdelovanca: 800 mm Maksimalna dolžina obdelovanca: 2.300 mm Fjdpsy Uwmqsfx Akwspi Maksimalna višina obdelovanca: 1.400 mm Maksimalna podajalna hitrost: 37 m/min PODROBNOSTI O STROJU Dolžina stroja: 4.800 mm OPREMA Dovajalni transportni trak Odvajalni transportni trak Stroj se prodaja in dobavi v dejanskem in pravnem stanju ("kot viden in všečen") na podlagi fotodokumentacije ter tehnično/komercialnih dokumentov opisnega značaja. Kupec ima pravico izdelek pred prevzemom pregledati in prevzema odgovornost za montažo, zavarovanje in uporabo stroja na ciljni lokaciji. Zunanja referenca: 8536

Stanje: rabljeno, Leto izdelave: 2002, številka stroja/vozila: 0-306-04-1262, delovna širina: 600 mm, dolžina transportnega traku: 3.000 mm, hitrost pomika os X: 40 m/min, delovna višina: 1.300 mm, delovna dolžina: 2.500 mm, Brez minimalne cene – zagotovljena prodaja najvišjemu ponudniku! Fpsdpfsy Uv Iyox Akwsi Prevzem stroja mora biti opravljen med 10.06.26 in 30.06.26! TEHNIČNE PODROBNOSTI Maks. širina obdelovanca: 600 mm Maks. dolžina obdelovanca: 2.500 mm Maks. višina obdelovanca: 1.300 mm Min. širina obdelovanca: 120 mm Min. dolžina obdelovanca: 300 mm Min. višina obdelovanca: 300 mm Maks. dovodna hitrost: 40 m/min Dolžina transportnega traku: 3.000 mm PODROBNOSTI O STROJU Krmilni sistem: NC 16 OPREMA Izvozni transportni trak CE oznaka Stroj se prodaja in dostavlja v dejanskem in pravnem stanju ("videno-kupljeno") na podlagi fotodokumentacije in tehničnih/komercialnih opisnih listin. Kupec ima pravico priskusiti blago pred prevzemom in je odgovoren za inštalacijo, varnost in uporabo stroja na namembnem kraju. Zunanja referenca: 8535

Stanje: zelo dobro (rabljeno), Italpresse Program/30 Hydraulic Assembly Press for Window and Door Joinery The Italpresse Program/30 is a vertical hydraulic press designed for the precise assembly and gluing of wooden components such as window frames, door frames, and furniture carcasses. Its construction allows for accurate alignment and durable bonding of components, which is crucial for the production of joinery and furniture elements. Technical specifications • Maximum working dimensions: 3000 × 1700 mm • Vertical cylinder stroke: 800 mm • Horizontal cylinder stroke: 1200 mm • Adjustable lower beam: three-position setting • Hydraulic cylinders: • 2 vertical (Ø 100/60 mm) • 2 horizontal for frame positioning (Ø 50/35 mm) • Hydraulic unit power: 2.2 kW • Overall dimensions: 3600 × 1000 × 2650 mm • Weight: approx. 1200 kg Applications The Italpresse Program/30 is ideal for: • Gluing and assembly of window and door frames • Assembling furniture carcasses • Mounting wooden panels and other building joinery components Fpsdpfjwkf Stox Akwei

Stanje: zelo dobro (rabljeno), Hess korpusna stiskalnica Tip: Export, pnevmatska Proizvajalec: Hess Tip: Export Velikost korpusa: maks. 2.500 x 1.500 mm Tlak stiskanja: 1.400 kp zmogljivost na stiskalno enoto pri 15 bar Število cilindrov, vertikalno: 2 + 2 tlačni cilindri Število cilindrov, horizontalno: 2 + 2 tlačni cilindri Mere: 3.900 mm x 2.500 mm x 600 mm Teža: 1.060 kg Fedpfexgvwpox Akwjpi Hess korpusna stiskalnica Export, pnevmatska 2 vertikalni stiskalni agregati, vsak z 2 tlačnima cilindroma, premer cilindra 80 mm, hod cilindra 110 mm, 1.400 kp tlačne zmogljivosti na agregat pri 15 bar, 2 horizontalni stiskalni agregati, vsak z 2 tlačnima cilindroma, premer cilindra 80 mm, hod cilindra 110 mm, 1.400 kp tlačne zmogljivosti na agregat pri 15 bar, pri tem je zgornji zaradi protiuteži zelo lahko premikljiv, postopek stiskanja se upravlja preko 2 vrtljivih drsnih ventilov z nastavitvami Stiskanje - Stop - Sprostitev, servisna enota z redukcijskim ventilom 0 - 15 bar, manometer in oljna megla, anodizirane merilne letve, snemljive noge Lokacija: pri stranki - takoj na voljo -

Stanje: kot nova (razstavni stroj), Leto izdelave: 2024, Technical data: Laminated carcass press from our showroom; Working range: Width from 150 - 2,550 mm, Height from 150 - 1,400 mm; Depth from 150 - 700 mm; Variable pressing force adjustment 300/700/1100/1400/1800/2200 daN (kg) for the side pressing beam; Fpjdob Eln Dopfx Akwsi Variable pressing force adjustment 500/800/1200/1500/1900/2200 daN (kg) for the upper pressing beam. Easy operation via 6 separate pressure buttons, freely adjustable pressing time preselection with automatic opening function, loading height 300 mm. The machine is available for immediate delivery from our showroom. Location: ex stock 54634 Bitburg

Stanje: novo, Leto izdelave: 2026, Gannomat Concept 70 Eco Lamella case clamp with rapid traverse Technical Specifications: Lamella case clamp from our showroom; Working range: width from 150 to 2,500 mm, height from 150 to 1,400 mm; depth 700 mm; - Top lamella pressure beam with 6 elements, side lamella pressure beam with 5 elements - Lamella pressure beams with proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are continuous 40 mm thick, coated support plates - The pressing force of the pressure beams is infinitely adjustable electronically via 2 potentiometers and set via a frequency converter—thus, torque transmission is absolutely wear-free. - Pressing force for the horizontal pressure beams: min. 500 daN (kg) up to infinitely adjustable max. 2200 daN (kg) - Pressing force for the vertical pressure beams: min. 300 daN (kg) up to infinitely adjustable max. 2200 daN (kg) - Including options: Rapid traverse speed for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams; pressing speeds 5/10/25 mm/sec and rapid traverse speed 50 mm/sec. The sensors can be deactivated for pressing special parts. - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and 45° carcasses. Simple operation via 6 separate push-buttons, freely selectable pressing time preselection with automatic opening, loading height 300 mm. Fjdpfx Asy Egz Sjkwopi The machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Stanje: novo, Leto izdelave: 2026, AREA - CARCASE PRESS GANNOMAT "CONCEPT 70 EASY 170" Complete in standard version with: - Sturdy, torsion-resistant frame made of steel, welded and bolted construction - SIDE press beam with continuous pressure surface and 25 mm thick, coated support plate - Counterpressure surfaces (side pressure wall, bottom) are 25 mm thick, coated, continuous support plates - Electromotive adjustment of the press beam via precision trapezoidal-thread spindles (with increased pitch and running accuracy) and high-performance slide nuts with grease reservoir - Pressing is performed electromotively via worm gear motor (0.75 kW) Fedpow Sgnkofx Akwjpi - Pressing force of the press beam can be continuously adjusted electronically via potentiometer and regulated via frequency inverter, therefore press force control is completely wear-free - Press force for vertical press beam min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Press and adjustment speed of the press beams with fine positioning, via 3-position selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of the press beam, e.g., for low pressing forces such as drawers, etc. - Very easy operation via two separate pushbuttons; two motion sequences (open/close) can be selected via the controller - Freely adjustable pressing time preselection 0-30 min (switchable to seconds or hours) with individually programmable opening dimensions for both press beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Availability: short-term

Stanje: novo, Leto izdelave: 2025, Gannomat Concept 70 Eco Lamella Case Clamp with Rapid Traverse Technical Data: Lamella case clamp from our showroom; Working range: Width from 150 to 2,500 mm, height from 150 to 1,400 mm; depth 700 mm; - Upper lamella pressure beam with 6 elements, lateral lamella pressure beam with 5 elements Fpjdpfxeiidm No Akwei - Lamella pressure beams with proven tolerance compensation for tightly glued carcass joints - Counterpressure surfaces: continuous, coated support plates, 40 mm thick - Pressing force of the pressure beams is infinitely electronically adjustable via 2 potentiometers and set using a frequency converter, ensuring absolutely wear-free torque transmission. - Pressing force for horizontal pressure beams: min. 500 daN (kg) up to infinitely adjustable max. 2,200 daN (kg) - Pressing force for vertical pressure beams: min. 300 daN (kg) up to infinitely adjustable max. 2,200 daN (kg) - Included Option: Rapid traverse speed for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors integrated in the pressure beams. Pressing speeds: 5/10/25 mm/sec; rapid traverse speed: 50 mm/sec. Sensors can be deactivated for special workpiece clamping. - Jog mode for precise positioning of both pressure beams, e.g., for low pressing forces, drawer boxes, and 45-degree carcasses. Simple operation via 6 separate pushbuttons. Freely adjustable pressing time pre-selection with automatic opening, loading height 300 mm. The machine is on display at our showroom and available for immediate delivery. Location: ex stock 54634 Bitburg - available immediately -

Stanje: rabljeno, Leto izdelave: 2024, New demonstration machine! List price: €32,665 – Complete in standard configuration with: Sturdy, torsion-free steel frame in welded and bolted construction – TOP lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements – Lamella pressure beams feature the proven Ganner system tolerance compensation for tightly pressed carcass joints – Counterpressure surfaces (side pressure wall, base) are continuous, 38 mm thick, coated support panels – Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam – Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir – Pressing is performed electromechanically by two separate worm gear motors (2 x 0.75 kW) – Pressing force of the pressure beams is infinitely adjustable via two potentiometers and regulated by frequency converters, making the pressure regulation absolutely wear-free – Pressing force for the horizontal beam: min. 500 daN (kg) up to max. 2200 daN (kg), stepless – Pressing force for the vertical beam: min. 300 daN (kg) up to max. 2200 daN (kg), stepless – Pressing and adjustment speed of the beams with fine positioning, selectable via 3-step switch: 5 / 10 / 25 mm/second – Simple operation via 6 separate push-buttons, 8 movement sequences selectable via control unit – Freely adjustable pressing time preselection with automatic opening (0–30 min, switchable to seconds or hours) – Working height/loading height: 300 mm – Working dimensions: Length min: 150 mm, max: 2500 mm | Height min: 150 mm, max: 1400 mm | Depth: 700 mm – Weight: approx. 1800 kg net – Dimensions (L x W x H): 3.45 m x 0.95 m x 2.30 m – Electrical connection: 400V, 3Ph, 50Hz (3.2 kVA, 16A). Additional features: Fpjdpfsuf Hx Hsx Akwji Rapid traverse speed for quick positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams. Pressing speeds: 5 / 10 / 25 mm/sec and rapid traverse: 50 mm/sec. Sensors can be deactivated for pressing custom parts. 1 set of machine feet (working height 500 mm). Location:

Stanje: dober (rabljeno), leto: 2012 Fedpozhg I Usfx Akwjpi Maksimalne mere stiskalnice: D 2500 x V 1300 x Š 700 mm Ročni/samodejni način Žična tipka za nujni izklop pod strojem V dobrem delovnem stanju Mere stroja: D 3600 x Š 900 x V 2200 mm, teža: 2440 kg Za predstavitev na WHATSAPP povprašajte

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, Gannomat Concept 70 Eco Carcass Press Year of manufacture: 2025 including the following options: - Rapid traverse motion speed adjustment up to 50 mm/sec - Machine feet (working height 500mm) The Concept Eco and Concept Primus are ideal assembly aids for dowel joints during carcass pressing as well as for drawer production. Brief overview: • Field-proven tolerance compensation (GANNOMAT system) • Two potentiometers for infinitely adjustable pressing force • Pressing force min. 300/500 daN (kg) on Concept Eco, Pressing force min. 600/800 daN (kg) on Concept Primus • Pressing force max. 2200 daN (kg) on Concept Eco, Pressing force max. 3500 daN (kg) on Concept Primus • Three pressing and motion speeds: 5 / 10 / 25 mm/sec (with fine positioning / creep speed) • Freely adjustable pressing time preselection with automatic opening function • Concept Eco: Very simple operation using 6 separate pushbuttons for 8 movement functions • Concept Primus: Very simple operation via LCD display Universal applications: • Cabinets, e.g. for furniture and wardrobes • Mitre carcasses • Carcasses with protruding tops • Drawers, drawer boxes • Simultaneous pressing of multiple carcasses / drawers Advantages: • Industry-proven tolerance compensation (GANNOMAT system) • Electromechanical carcass press with frequency-controlled geared motors • Independent vertical and horizontal pressure beams • Long service life due to proven, high-quality components • Solid and robust construction Fodpfxovxgrro Akwopi • Space-saving design • Carcass pressing = Simple + Fast + Efficient + Flexible + Precise + Professional • Simple due to user-friendly, practical control panel • Fast due to positioning speed of pressure beams up to 50 mm/sec (option) • Efficient through precise pressing of various carcass sizes • Flexible thanks to adjustable parameters like pressing force, pressing time, and motion speed • Precise due to angle-accurate pressing of furniture carcasses and drawers • Professional production of carcasses and drawers with a modern carcass press

Stanje: zelo dobro (rabljeno), Leto izdelave: 1991, številka stroja/vozila: 211/91/1, Funkcionalnost: popolnoma funkcionalen, vhodni tok: 16 A, vhodna frekvenca: 50 Hz, širina mize: 750 mm, dolžina mize: 2.700 mm, skupna dolžina: 3.650 mm, skupna širina: 850 mm, skupna višina: 2.300 mm, skupna masa: 2.200 kg, dvižna višina: 1.350 mm, delovna širina: 750 mm, dolžina obdelovanca (maks.): 2.500 mm, širina obdelovanca (maks.): 750 mm, višina obdelovanca (maks.): 1.300 mm, vrsta nastavitve višine: električni, potrebna višina: 2.300 mm, zahteva za prostor dolžina: 3.650 mm, potrebna širina: 950 mm, delovna dolžina: 2.500 mm, - Lamelna stiskalnica za ohišja - Delovno območje: - Širina od 150 do 2.500 mm, višina od 150 do 1.300 mm; globina 750 mm; Fodpfx Akjyx Habjwopi - 2200 daN (kg) - Zmogljivost nastavljiva na 85 % + 70 %. - Zelo robusten stroj

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 1988, številka stroja/vozila: 100.613, Funkcionalnost: popolnoma funkcionalen, Stroj kratkoročno na voljo Viličar za nakladanje na voljo 2 cilindra na vsako stiskalno enoto Hod cilindra pribl. 110 mm Maksimalni pritisk stiskanja cca 1000 kp Delovna širina 250 - 2500 mm Delovna višina 250 - 1250 mm Delovna globina max. 600 mm Električna nastavitev višine centralne vertikalne enote po merilu Ročna nastavitev centralne horizontalne enote v korakih po 50 mm s pnevmatskim vpenjanjem Ločeno upravljanje vertikalnih in horizontalnih agregatov za pritisk preko ročnega upravljalnega ventila Regulacija sile pritiska 4 - 10 bar Fsdpfx Aoy Tly Ajkwjpi

Stanje: zelo dobro (rabljeno), Prehodna stiskalnica (korpusna stiskalnica) Elektro-mehanski sistem tlaka Sistem samocentriranja Motorizirani transportni in montažni trak (skozi stiskalnico) mm 4500 Podajalna hitrost (nastavljiva) m/min 10-40 Skupna dolžina stroja (mm) 4400 DIMENZIJE KORPUSNEGA POHIŠTVA Min. dolžina korpusnega pohištva (mm) 250 Maks. dolžina korpusnega pohištva (mm) 2500 Min. globina (širina) korpusnega pohištva (mm) 250 Maks. globina (širina) korpusnega pohištva (mm) 700 Min. višina korpusnega pohištva (mm) 250 Maks. višina korpusnega pohištva (mm) 1200 Fjdpfx Akoyzh I Sewjpi Krmiljenje PLC "OMRON" Skupna priključna moč (kW) 8,8

Stanje: zelo dobro (rabljeno), Pass-through system (cabinet furniture bodies) Mechanical pressing system (with asynchronous motors + inverter) Self-centering system Motorized transport and assembly line: 4500 mm Feed speed (adjustable): 10–40 m/min Overall machine length: 4500 mm Movable vertical press, movable horizontal press CABINET FURNITURE DIMENSIONS Minimum cabinet body length: 250 mm Maximum cabinet body length: 2500 mm Minimum cabinet body depth (width): 200 mm Maximum cabinet body depth (width): 700 mm Minimum cabinet body height: 250 mm Maximum cabinet body height: 1200 mm Motorized infeed conveyor for cabinet bodies Length of conveyor for feeding cabinet bodies: 2500 mm Electronic PLC programmer (separate control console) Total connected load: 7 kW Stapler E/S 250 (automatic) Fedpfx Akjgz Acaswjpi

Stanje: zelo dobro (rabljeno), A) Case clamp with CNC (electronic) Type MDE 110/28/08 Motorized transport and assembly conveyor Feed speed: 12 - 40 m/min CNC control Power Control PC C 22 T Total power 14 kW Overall machine length 6,220 mm Fsdpfx Akolkbn Ijwspi Processing capacity for workpieces (mobile): Length Min / Max: 250 / 2,800 mm Depth Min / Max: 120 / 800 mm Height Min / Max: 280 / 1,320 mm B) Motorized transport conveyor Mod. MTB 200/20/08 (length 2,000 mm) C) Motorized transport conveyor Mod. MTB 200/20/08 (length 2,000 mm)