Vertikalni Stroj Za Razrez Pločevine nakup rabljenega (85.771)

Stanje: novo, Condition: new Delivery time: approx. 12–14 weeks from order Country of origin: Turkey Price: €98,600 Leasing rate: €1,863.54 Bending length: 3,100 mm Max. bending capacity – structural steel: 16 mm Max. plate thickness without pre-bending at D=5x top roller: 16 mm Max. plate thickness without pre-bending at D=3x top roller: 13 mm Max. plate thickness without pre-bending at D=1.5x top roller: 16 mm Max. plate thickness with pre-bending at D=5x top rollers: 14 mm Max. plate thickness with pre-bending at D=1.5x top roller: 12 mm Top roller diameter: 300 mm Bottom roller diameter: 300 mm Side roller diameter: 240 mm Max. opening: 50 mm Working height: 1,140 mm Motor power: 18.5 kW Length: 5,310 mm Width: 1,660 mm Height: 1,140 mm Weight: 11,100 kg 4 rollers PLC Fully hydraulic drive of top and bottom roller (from 30 mm bending capacity for all four rollers) via planetary gearbox Hydraulic side roller adjustment with electronic synchronization Hydraulic bottom roller adjustment with mechanical synchronization Adjustable clamping pressure Hjdpfoynm Hfox Ag Tsi Variable roll speed Hardened rollers Cone bending device Hydraulic drop-end bearing Movable control panel Overload protection Operating manual in GERMAN and ENGLISH Equipment according to CE standards OPTIONS: Upper and side plate supports NC control IMPORTANT POINTS FOR CONICAL ROLLING: Max. plate thickness is 50% of nominal capacity Cone length may be max. 30% or must be more than 60% of the roller length Hardened rollers are recommended

Stanje: novo, Condition: New Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €103,100 Leasing rate: €1,948.59 Bending length: 2550 mm Max. bending capacity – structural steel: 25 mm Max. sheet thickness without prebending at D=5x top roll: 25 mm Max. sheet thickness without prebending at D=1.5x top roll: 20 mm Max. sheet thickness with prebending at D=5x top roll: 20 mm Max. sheet thickness with prebending at D=1.5x top roll: 16 mm Top roll diameter: 350 mm Bottom roll diameter: 350 mm Hedpfx Asynm Eujg Tji Side roll diameter: 260 mm Rolling speed: 1.5–5 m/min Motor power: 22 kW Length: 5500 mm Width: 2000 mm Height: 1900 mm Weight: 13,000 kg 4 rolls Fully hydraulic drive of top and bottom rolls Hydraulic adjustment of bottom and side rolls Digital display for lower and side roll positions Hardened rolls Cone bending device Hydraulic release of top roll Hydraulic drop-end bearing 2 working speeds Central lubrication Overload protection Movable control panel Equipment according to CE regulations OPTIONS: Infinitely adjustable rolling speed Hydraulic side support Hydraulic top support NC control IMPORTANT NOTES FOR CONICAL BENDING: The maximum sheet thickness is 50% of the nominal capacity The cone length may be max. 30% or must be more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: New Delivery time: approx. 12 weeks from order Country of origin: Turkey Hsdpfxoynm Enj Ag Tji Price: €97,400 Lease rate: €1,840.86 Bending length: 2,050 mm Max. bending capacity (mild steel): 30 mm Max. plate thickness without pre-bending at D=5x upper roll: 30 mm Max. plate thickness without pre-bending at D=1.5x upper roll: 25 mm Max. plate thickness with pre-bending at D=5x upper roll: 25 mm Max. plate thickness with pre-bending at D=1.5x upper roll: 20 mm Upper roll diameter: 350 mm Lower roll diameter: 350 mm Side roll diameter: 260 mm Rolling speed: 1.5–5 m/min Motor power: 22 kW Length: 5,000 mm Width: 2,000 mm Height: 1,900 mm Weight: 11,000 kg 4 rolls Fully hydraulic drive of upper and lower rolls Hydraulic adjustment of lower and side rolls Digital display for lower and side roll positions Hardened rolls Conical bending device Hydraulic top roll release Hydraulic drop-end bearing 2 working speeds Centralized lubrication Overload protection Mobile control panel Equipment according to CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hydraulic top support NC control IMPORTANT NOTES ON CONICAL ROLLING: The max. plate thickness is 50% of the rated capacity The cone length may be a maximum of 30% or must be at least 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: new Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €53,700 Leasing rate: €1,014.93 Bending length: 2,050 mm Max. bending capacity (mild steel): 16 mm Max. sheet thickness without prebending at D=5x top roll: 16 mm Max. sheet thickness without prebending at D=1.5x top roll: 13 mm Max. sheet thickness with prebending at D=5x top roll: 13 mm Max. sheet thickness with prebending at D=1.5x top roll: 10 mm Top roll diameter: 260 mm Lower roll diameter: 260 mm Side roll diameter: 200 mm Rolling speed: 1.5 / 6 m/min Motor power: 7.5 kW Length: 4,300 mm Width: 1,600 mm Height: 1,550 mm Weight: 6,100 kg 4 rolls Top roll drive via hydraulic motor and planetary gearbox, lower roll drive via gear and cardan shaft Hydraulic adjustment of lower and side rolls Digital position display for lower and side rolls Hardened rolls Cone bending device Hydraulic relief for top roll Hydraulic drop-end bearing 2 working speeds Overload protection Mobile control panel Equipment complies with CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hodeynm Ehopfx Ag Tji Hydraulic top support NC control IMPORTANT POINTS FOR CONICAL ROLLING: The max. sheet thickness is 50% of the rated capacity The cone length must be max. 30% or more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: New Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €111,500 Leasing rate: €2,107.35 Bending length: 3,100 mm Max. bending capacity – mild steel: 20 mm Max. plate thickness without pre-bending (D=5x top roll): 20 mm Max. plate thickness without pre-bending (D=1.5x top roll): 16 mm Max. plate thickness with pre-bending (D=5x top roll): 16 mm Max. plate thickness with pre-bending (D=1.5x top roll): 12 mm Top roll diameter: 350 mm Lower roll diameter: 350 mm Side roll diameter: 260 mm Rolling speed: 1.5–5 m/min Motor power: 22 kW Length: 6,000 mm Width: 2,200 mm Height: 1,900 mm Weight: 15,000 kg 4-roll design Full hydraulic drive of top and bottom rolls Hydraulic adjustment of lower and side rolls Digital readout for lower and side roll positions Hardened rolls Conical bending device Hydraulic release of the top roll Hjdpfx Agjynm Ebj Tsi Hydraulic drop-end bearing 2 working speeds Centralized lubrication Overload protection Mobile control panel Equipment according to CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hydraulic top support NC control IMPORTANT POINTS FOR CONICAL BENDING: The maximum plate thickness is 50% of the nominal capacity The cone length must be a maximum of 30% or more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: New Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €60,600 Leasing rate: €1,145.34 Bending length: 3,100 mm Max. bending capacity (mild steel): 10 mm Max. sheet thickness without pre-bending at D = 5x top roller: 10 mm Max. sheet thickness without pre-bending at D = 1.5x top roller: 8 mm Max. sheet thickness with pre-bending at D = 5x top roller: 8 mm Max. sheet thickness with pre-bending at D = 1.5x top roller: 6 mm Top roller diameter: 260 mm Bottom roller diameter: 260 mm Side roller diameter: 200 mm Rolling speed: 1.5 / 6 m/min Motor power: 7.5 kW Length: 5,350 mm Width: 1,600 mm Height: 1,550 mm Weight: 7,685 kg 4 rollers Top roller driven by hydraulic motor and planetary gearbox, bottom rollers driven by gear drive and cardan shaft Hydraulic adjustment of bottom and side rollers Digital display for bottom and side roller positions Hardened rollers Cone bending device Hydraulic release of the top roller Hydraulic drop-end bearing 2 working speeds Overload protection Mobile control console Equipment in accordance with CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hydraulic top support NC control Hsdpfjynm D Rsx Ag Tsi IMPORTANT NOTES FOR CONICAL BENDING: Maximum sheet thickness is 50% of the rated capacity Cone length must be a maximum of 30% or more than 60% of the roller length Hardened rollers are recommended

Stanje: novo, Condition: new Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €32,480 Leasing rate: €620.37 Bending length: 1,550 mm Max. bending capacity - structural steel: 9 mm Max. plate thickness without pre-bending at D=5x upper roll: 9 mm Max. plate thickness without pre-bending at D=1.5x upper roll: 7 mm Max. plate thickness with pre-bending at D=5x upper roll: 7 mm Max. plate thickness with pre-bending at D=1.5x upper roll: 5 mm Upper roll diameter: 180 mm Hodpfxeynmzpo Ag Tei Lower roll diameter: 180 mm Side roll diameter: 150 mm Rolling speed: 1.5 / 6 m/min Motor power: 5.5 kW Length: 3,900 mm Width: 1,150 mm Height: 1,250 mm Weight: 3,250 kg 4 rolls Top roll drive by hydraulic motor and planetary gearbox, lower roll drive via gear and cardan shaft Hydraulic adjustment of lower and side rolls Digital display for lower and side roll positions Hardened rolls Cone bending device Hydraulic top roll release Hydraulic drop-end bearing 2 working speeds Overload protection Mobile control panel Equipment according to CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hydraulic top support NC control IMPORTANT POINTS FOR CONICAL BENDING: The maximum plate thickness is 50% of the nominal capacity The cone length must be a maximum of 30% or more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: New Delivery time: approx. 12 weeks from order Country of origin: Turkey Price: €73,200 Leasing rate: €1,383.48 Bending length: 2,050 mm Max. bending capacity – mild steel: 20 mm Max. sheet thickness without prebending at D=5x upper roll: 20 mm Max. sheet thickness without prebending at D=1.5x upper roll: 16 mm Max. sheet thickness with prebending at D=5x upper roll: 16 mm Max. sheet thickness with prebending at D=1.5x upper roll: 12 mm Upper roll diameter: 280 mm Lower roll diameter: 280 mm Side roll diameter: 220 mm Rolling speed: 1.5 / 5 m/min Motor power: 16.5 kW Length: 4,350 mm Width: 1,700 mm Height: 1,850 mm Weight: 8,550 kg 4 rolls Hsdpfx Agsynmylj Tei Fully hydraulic drive for upper and lower rolls Hydraulic adjustment of lower and side rolls Digital display for lower and side roll positions Hardened rolls Cone bending device Hydraulic release of upper roll Hydraulic drop-end bearing 2 working speeds Centralized lubrication Overload protection Mobile control panel Equipment according to CE regulations OPTIONS (PRICES ON REQUEST): Steplessly variable rolling speed Hydraulic side support Hydraulic top support NC control system IMPORTANT NOTES ON CONICAL BENDING: The max. sheet thickness is 50% of the nominal capacity The cone length must be max. 30% or more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: New Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €40,900 Leasing rate: €781.19 Bending length: 2050 mm Max. bending capacity – mild steel: 10 mm Max. plate thickness without pre-bending (at D = 5x top roll): 10 mm Max. plate thickness without pre-bending (at D = 1.5x top roll): 8 mm Max. plate thickness with pre-bending (at D = 5x top roll): 8 mm Max. plate thickness with pre-bending (at D = 1.5x top roll): 6 mm Top roll diameter: 200 – 220 mm Lower roll diameter: 200 – 220 mm Side roll diameter: 160 mm Rolling speed: 1.5 / 6 m/min Motor power: 5.5 kW Length: 4400 mm Width: 1150 mm Height: 1250 mm Weight: 3950 kg 4 rolls Top roll driven by hydraulic motor and planetary gearbox, lower roll driven by gears and cardan shaft Hydraulic adjustment of lower and side rolls Digital display for lower and side roll positions Hardened rolls Hodsynmyfjpfx Ag Tsi Cone bending device Hydraulic top roll release Hydraulic drop-end bearing 2 working speeds Overload protection Mobile control panel Equipment in accordance with CE regulations OPTIONS: Infinitely variable rolling speed Hydraulic side support Hydraulic top support NC control IMPORTANT POINTS FOR CONE BENDING: The max. sheet thickness is 50% of the nominal capacity The cone length may be a maximum of 30% or must be more than 60% of the roll length Hardened rolls are recommended

Stanje: novo, Condition: new Delivery time: approx. 10 weeks from order Country of origin: Turkey Price: €43,550 Leasing rate: €831.81 Bending length: 1,550 mm Max. bending capacity – mild steel: 12 mm Max. sheet thickness without pre-bending at D=5x top roller: 12 mm Max. sheet thickness without pre-bending at D=1.5x top roller: 10 mm Max. sheet thickness with pre-bending at D=5x top rollers: 10 mm Max. sheet thickness with pre-bending at D=1.5x top roller: 8 mm Top roller diameter: 220 mm Lower roller diameter: 200 mm Side roller diameter: 160 mm Rolling speed: 1.5 / 6 m/min Motor power: 5.5 kW Length: 3,900 mm Width: 1,150 mm Height: 1,250 mm Weight: 3,600 kg 4-roll design Top roll driven by hydromotor and planetary gearbox, lower roll driven by gear and cardan shaft Hydraulic adjustment of lower and side rolls Digital display for lower and side roll positions Hardened rolls Conical bending device Hydraulic top roll lifting Hydraulic drop-end bearing 2 working speeds Overload protection Movable control panel Equipment according to CE regulations OPTIONS: Infinitely variable roll speed Hydraulic side support Hydraulic top support NC control IMPORTANT NOTES FOR CONICAL ROLLING: Max. sheet thickness is 50% of the nominal capacity The cone length may be max. 30% or must be more than 60% of the roll length Hodpfx Agsynmx Io Tei Hardened rolls are recommended

Stanje: novo, Condition: new Delivery time: approx. 12 weeks from order Country of origin: Italy Hedpjynmw Rsfx Ag Tei Price: €153,200 Leasing rate: €2,895.48 Working width: 1350 mm Sheet thickness range – mild steel: 0.4 – 120 mm Abrasive belt dimensions: 1370 x 2200 mm Extraction capacity: 6000 m³/h Connection for extraction: Diameter 150 mm Compressed air connection: 6 bar Length: 4200 mm Width: 2300 mm Height: 2350 mm Weight: 4200 kg WITH 2 WORKING UNITS: 1 X ABRASIVE BELT AND 1 X BRUSH UNIT ABOVE * The machine is built from welded and normalized steel to ensure a stable and rigid structure. * Worktable with motorized height adjustment enabled by synchronized movement of 4 screws. * Independent motors with emergency brakes integrated within the machine frame. * Dust extraction hoods within the machine. The control panel includes: * Automatic star-delta starter for main motors * Digital display for material thickness with decimal accuracy * Thickness adjustment with control (+/- 0.1) * Alarm control center for immediate visualization of emergencies and/or faults. FEED UNIT * Table constructed of a solid metal structure with a ground and wear-resistant gliding surface. * Modified structures for vacuum systems available on request * Table lifts and lowers from 780 mm to a maximum height of 950 mm above floor level. Table height adjustment motor output: 0.25 kW. * Maximum permissible load on the table: 140 kg. * Variable feed speed via inverter from 0.4 to 4.5 m/min, optional: 0.2 to 2.0 m/min or 0.6 to 6.0 m/min. * Conveyor belt made of special natural rubber, oil- and heat-resistant, with automatic centering system. * Side guides preventing the conveyor from lifting. * Rubberized pressure rollers, oil- and heat-resistant, fitted before and after each working unit. * Automatic centering device for the conveyor belt * Automatically servo-cooled motor * Speed motor displayed on the main touchscreen 1ST DEBURRING UNIT WITH ABRASIVE BELT * Rectified and balanced contact roller, 180 mm diameter. Coated with oil- and heat-resistant nitrile rubber. Standard roller hardness 55° Shore. Mounted on an eccentric shaft, allowing control of working position and compensation for abrasive belt wear, up to 8 mm. This system is controlled by a pneumatic cylinder which enables the group to be engaged automatically and, in the event of an emergency and/or machine stop, allows immediate withdrawal of the belt from the working area. Abrasive belts and/or Scotch-Brite can be mounted. * Pneumatic ON/OFF switch. * Roller adjustment up/down ("grain" stroke 10 mm) * Variable speed motor 11 kW with automatic braking in case of emergency. * Rotational speed in feed direction: 4 – 18 m/s. * Adjustable width and duration of oscillation. * Pneumatic abrasive belt tensioning system. LED indicator for wear control. * Abrasive belt centering system with electronic photo cell indicator; amplitude and intensity of oscillation adjustable. 2ND ROTARY BRUSHING UNIT * Consisting of 8 deburring brushes, 4 rotating clockwise and 4 counterclockwise. * Each brush has a diameter of 350 mm and...

Stanje: novo, Condition: New Delivery time: approx. 12 - 14 weeks from order Country of origin: Italy Price: €74,000 Leasing rate: €1,398.60 Working width: 1,350 mm Sheet thickness range (mild steel): 0.5 - 170 mm Abrasive belt dimensions: 1,370 x 2,200 mm Extraction capacity: 4,000 m³/h Extraction connection: diameter 200 mm Compressed air connection: 6 bar Noise level: 78 (+/-2) dB Length: 1,750 mm Width: 2,100 mm Height: 2,180 mm Weight: 2,000 kg EQUIPPED WITH 2 WORKING STATIONS: 1 x ABRASIVE BELT AND 1 x TOP BRUSH UNIT Machine made of stress-relieved steel welded construction for stable and rigid structure. Worktable with motorized height adjustment via 4 synchronized spindles. Independent drive motors for each working station. Extraction hoods inside the machine, one per station. Touch screen for * Automatic star-delta switching of main motors * Analog ammeter for each station * Digital sheet thickness display with decimal point tolerance * Material thickness setting (+/- 0.1 mm) * Machine status monitoring with alarm messages FEED SYSTEM Robust steel structure, wear-resistant surface. Vacuum conveyor belt available on request. Variable feed speed via frequency inverter, 0.6 to 6.5 m/min. Rubber conveyor belt, oil and temperature resistant. Automatic conveyor belt centering. Side guides to prevent the belt from lifting. Rubber pressure rollers before and after each station, oil and temperature resistant. Idler rollers at the front and rear of the table. 1st WORKING STATION – R Balanced contact roller, anti-oil and anti-heat nitrile rubber coating. Adjustable via eccentric shaft for working position and compensation of abrasive belt wear. Pneumatic cylinders for automatic engagement in working position and lifting during emergency stop. Abrasive belts and/or Scotch-Brite can be used. Motorized adjustment and electronic control of contact roller height. Variable-speed motor with automatic emergency brake. Pneumatic belt tensioning system. Abrasive belt centering system with electronic photo cell. Oscillation adjustment for width and timing. Contact roller adjustment precision: ±0.02 mm Contact roller adjustment speed: 10 m/min Contact roller diameter: 180 mm Rubber roller hardness: 55 Shore Contact roller stroke (grit adjustment) up/down: 8 mm Abrasive belt speed: 3 – 18 m/s Motor power: 11 kW 2nd WORKING STATION – X 2 rows of vertical brushes, 10 rotating clockwise and 10 counterclockwise Oscillating cross movement of the whole group Quick-change system for brushes Brush diameter: 115 mm Number of brushes: 20 pcs Oscillation stroke: 15 mm Rotational motor power: 5.5 kW Rotational speed: 300 – 1000 rpm Hedeynmwkopfx Ag Tji Oscillation motor power: 0.37 kW Abrasive brush speed: 10.0 m/s OPTIONS AND ACCESSORIES B Group – External horizontal drum brush Ø 150 mm over Scotch-Brite brush: €5,580.00 over wire brush 0.3 mm: €5,900.00 R Group – ABRASIVE BELT Motor 15 kW: €1,060.00 OPTIONS: Return to Sender system (workpiece is discharged to the front): €1,290.00 Conveyor belt with vacuum system, 300 mm wide, 4.0 kW: €4,780.00 2 additional PVC-coated rollers at infeed and outfeed sides: €2,040.00 Tampico brush system for component cleaning, 0.55 kW, Ø 150 mm: €4,5...

Stanje: novo, Zustand neu Lieferzeit ca. 12 Wochen ab Auftrag Ursprungsland Türkei Preis 22.300 € Leasingrate 428,16 € Biegelänge 1.550 mm Max. Biegekapazität – Baustahl: 4,5 mm Max. Blechstärke ohne Anbiegung – Baustahl: 4,5 mm Max. Blechstärke mit Anbiegung – Baustahl: 3,5 mm Max. Blechstärke ohne Anbiegung bei D=5x Oberwalze: 4,5 mm Max. Blechstärke ohne Anbiegung bei D=1,5x Oberwalze: 3,5 mm Max. Blechstärke mit Anbiegung bei D=5x Oberwalze: 3,5 mm Max. Blechstärke mit Anbiegung bei D=1,5x Oberwalze: 2,5 mm Oberwalzendurchmesser: 130 mm Unterwalzendurchmesser: 130 mm Seitenwalzendurchmesser: 130 mm Rollgeschwindigkeit: 5 m/min Länge: 3.300 mm Breite: 1.150 mm Höhe: 1.110 mm Gewicht: 2.370 kg Motorischer Walzenantrieb Hsdpfoynmwdsx Ag Tji Ober- und Unterwalze angetrieben Hydraulische Seitenwalzenzustellung 3 Digitalanzeigen Hydraulische Abklapplager Gehärtete Walzen Konischbiegevorrichtung Betriebsanleitung in DEUTSCH oder ENGLISCH OPTIONEN: Topsupport Seitensupport Variable Geschwindigkeit NC Steuerung

Leto izdelave: 2015, Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 359, Oprema: CE označba, Stroj za pakiranje primeren za pakiranje v vrečke tipa "ciuffo" in "blazina". Dela z laminirano folijo. - Znamka: ROBYPAK - Model: V500 INOX S KLIPERJEM Hodoymngqspfx Ag Toi - Leto izdelave: 2015 - Trenutne dimenzije vrečk: -- - Konstrukcija: nerjaveče jeklo AISI 304 - Največja širina role folije: 500 mm PRIBOR, KI JE ŽE VKLJUČEN V STROJ ZA PAKIRANJE: - Priprava za datumski tiskalnik - Encoder za nevtralne folije (brez markerja). - Središčna fotocelica za tiskane folije - 1x oblikovalna cev širine 360 mm - 1x zadnji dovajalni trak - Barvni zaslon na dotik - PLC z Omron elektroniko - Širina vodoravnih varilnih letvic: 230 mm - Širina navpične varilne letve: 350 mm - Hitrost: 15/20 pakiranj na minuto s klipom (odvisno od produkta) Stanje: Rabljeno v mlečni industriji, v dobrem stanju, na voljo za ogled v naši poslovalnici. Za vprašanja ali dodatne informacije nas kontaktirajte preko sporočila ali telefona.

Stanje: dober (rabljeno), Leto izdelave: 1982, Maximum wheel diameter: 1250 mm Maximum module: 16 Minimum module: 1 Cutter speeds: 25...250 rpm Maximum face width for spur gears: 1000 mm Milling slide travel: 1000 mm Machine weight: approx. 24.5 t Machine type: L 1202 Maximum machinable module: 16 / DP 1.5 Minimum machinable number of teeth: see group 2.07 Maximum workpiece diameter: 1250 mm / 49.213" Workpiece table diameter: 1100 mm / 43.307" Pitch diameter: 987 mm / 38.858" Workpiece table bore: 250 mm / 9.843" Workpiece insertion depth: 525 mm / 20.669" Minimum cutter position above table: 390 mm / 15.354" Milling slide travel: 1000 mm / 39.370" Hodeynmptepfx Ag Tsi Axial feed: min.: 0.1 mm/rev / 0.0039" max.: 10.0 mm/rev / 0.3937" Radial feed, adjustable: min.: 0.10 mm/min / 0.0039" max.: 10.00 mm/min / 0.3937" Milling slide rapid traverse: 800 mm/min / 31.496" Main motor rated power: 2.6 ... 16 kW Main motor speed: 300 ... 3000 rpm Coolant pump flowrate: 200 litres / 52.835 US gal Table load max.: 8000 kg / 17637 lb Machine weight: approx. 21,000 kg / approx. 46,300 lb Cutter head type: 14.4500

Stanje: zelo dobro (rabljeno), Leto izdelave: 2008, X-hod 800 mm Y-hod 400 mm Z-hod 500 mm Hodpeymqwxefx Ag Tei Krmilnik Siemens Vpenjalna površina mize 1270 x 320 mm Hitrost vretena - brezstopenjska 0 - 6000 obr/min Razdalja vreteno / miza 100 - 600 mm Iztegnitev 510 mm Vpenjalo orodja SK 40 Teža stroja ca. 2,7 t Prostorske zahteve ca. 2,2 x 2,0 x 2,5 m

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2015, Material rezanja in previjanja: - Pocinkano, barvano jeklo in aluminij debeline 0.3 do 3.0 mm - Max. širina vhodne pločevine je 1550mm - širine trakov od 32 do 1550mm - hitrost linije do 50m/min Hsdpfxeygrv Aj Ag Tei - Nosilnost odvijalnika: 12.000 kg Največja širina koluta: 1,550 mm Premer notranje koluta: od 480 mm do 620 mm Razpiranje trna: hidravlično Odrez na dolžino: do 3000mm

Stanje: rabljeno, Leto izdelave: 2006, CNC portalni stroj za rezanje s plamenom Proizvajalec: Bach Tip: ACK-2D Leto izdelave: 2006 CNC krmiljenje: NBS300 Delovna miza: 1,5 x 6 m Hjdpfx Asw El Udog Tji 2 avtogen gorilnika 18226ä

Stanje: zelo dobro (rabljeno), Magnetna vpenjalna plošča 1.460 x 155 mm Vertikalno vreteno Dolžina brušenja tba mm Širina brušenja 225 mm Višina obdelovanca tba mm Plano brusilni stroj Göckel tip G50RSel za natančno obdelavo in ponovno ostrenje nožev, orodij in ravnih rezilnih orodij. Stroj je idealen za uporabo v mizarskih delavnicah, žagalnicah in servisih za orodja. Zaradi robustne konstrukcije in natančnih vodil omogoča natančne rezultate brušenja z visoko ponovljivostjo. Vključno z rezervoarjem za hladilno tekočino z avtomatskim filtrirnim sistemom. Hjdpfsyk Id Rex Ag Tji

Stanje: zelo dobro (rabljeno), Leto izdelave: 2009, Premer kolesa - max. 315 mm Širina kolesa 280 mm Modul - max. 8 Modul - min. 1 Krmiljenje Siemens 840 D Razdalja od sredine rezkala do vpenjalne površine 20 - 245 mm Razdalja vreteno / miza 190 - 470 mm Premer rezkala 160 mm Tangencialni pomik 110 mm Nagibni kot - max. 45 ° Število zob - min. 4 / 8 Dolžina rezkala max. 200 mm Površina mize 295 mm Hitrosti rezkala - brezstopenjske 50 - 400 U/min Skupna potrebna moč 58 kW Teža stroja cca. 8,5 t Prostorska potreba cca. 4,1 x 3,5 x 2,6 m Hodpfxjx N Ndko Ag Tji Stroj je bil leta 2009 generalno obnovljen pri SerWeMa in opremljen z Siemens Sinumerik 840D krmiljenjem. Možnosti uporabe: Ravna in poševna čelna zobnika, izbočena ali stožčasta čelna zobnika, polži in polžasta kolesa za enojne ali večkratne polže, polži, zobniki verige, zadrževalna kolesa, zobate gredi.

Stanje: novo, Leto izdelave: 2024, Stanje: novo Leto izdelave: 2024 Številka zaloge: 9722 Dobavni rok: takoj, vmesna prodaja možna Država izvora: Turčija Cena: 16.600 € Leasing obrok: 318,72 € Na zalogi: 1 Dolžina upogibanja: 2050 mm Maksimalna kapaciteta upogibanja - konstrukcijsko jeklo: 3 mm Premer zgornjega valja: 130 mm Hitrost valjanja: 3,5 m/min Moč motorja: 2,2 kW Dolžina: 3200 mm Širina: 750 mm Višina: 1000 mm Teža: 1500 kg 3 valji Asimetrična postavitev valjev - z predupogibanjem 2 pogonska valja z zavornim motorjem KALJENI VALJI ročno pomikanje stranskih valjev Zgornji valj se lahko izklopi naprej Tek naprej/nazaj Stožčasto valjanje z nastavkom zadnjega valja Premični upravljalni pult Navodila za uporabo v NEMŠČINI MOŽNOSTI: (Dobavni rok z možnostmi približno 8 tednov) motorno pomikanje stranskih valjev Hjdpfx Aewiqpbog Tji digitalni prikaz položaja stranskih valjev

Stanje: novo, Timesavers serija 12-300-WRBW Hedpoymlguofx Ag Tji Vakuumska miza Postaja 1: Predhodno brušenje, odstranjevanje ostankov in brizg Postaja 2: Zaobljanje robov z rotacijsko razigljevalno krtačo Postaja 3: Površinska obdelava s Scotch trakom

Stanje: zelo dobro (rabljeno), Serija 12-225-WRD 1. postaja: brusilni trak za odstranjevanje robov in laserskih sledi Hjdpsymlfdefx Ag Toi 2. postaja: disk za lahko zaobljanje robov Prehodna širina: 225 mm vključno s TEKA odsesovanjem

Stanje: rabljeno, Electrodynamic balancing machine for counterbalance shafts, vertical balancing machine, balancing machine SCHENCK RoTec Type EBLY Serial No. 1FLY Year of manufacture: 2000 Workpiece/Test specimen: Counterbalance shafts Number of measuring planes: 2 Number of correction planes: 2 Angular range for correction components: 145 - 215° Test body weight: max. 10 kg Indicated unbalance: 2 gmm/Div Minimum value per scale division: 8 gmm/Div Balancing spindle speed: 1200 rpm Scale disk with test body mounting: Ø 320 mm Test body diameter: max. 400 mm Vibration sensor: Force transducer P01 Angular position sensor: Incremental encoder HBBC Measuring device: CAB 750 microprocessor Interface: Serial RS232 Workpiece weight: 2.2 kg Workpiece length: 250 mm Workpiece diameter: 70 mm Power supply: 400 Volt, 50 Hz Rated current: 16 A - Balancing indicator SCHENCK M341 Required space (L x W x H): 2000 x 1800 x 2000 mm Weight: 620 kg Hodowgnu Nopfx Ag Tei Good condition

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2015, used Timesavers deburring machine 42-series-1350-WRB Technical Data: Year of manufacture: 2015 Condition: overhauled (2026) The machine is powered up and can be inspected by appointment! Max. working width: 1350 mm Abrasive belt dimensions (W x L): 1380 x 1900 mm Antistatic device Maximum weight: 100 kg Electrical connections: 400 V Frequency: 50 Hz 1st Unit: Contact roller ø 180 mm Contact roller, 55° Shore NI, grooved Pneumatic oscillation Fine adjustment via lifting and lowering of the contact roller Dial gauge Main motor: 15 kW Processing speed: 11 m/s, in feed direction 2nd Unit: Rotary brush unit 8 brushes, ø 350 mm Motorised height adjustment with toggle switch Drive motors: 5 x 1.5 kW Rotary unit speed, frequency-controlled Processing speed: 6–17 m/s 3rd Unit: Hjdpfx Asyk U Szjg Tji Panel edge cleaning brush Feed: Fixed vacuum table Feed belt: flat, perforated, oil- and heat-resistant, flame-retardant Feed motor: 2.6 kW, frequency-controlled, 0.6–8 m/min Toggle switch for feed belt forward/reverse Motorised table height adjustment: 0.18 kW, 0–100 mm, digital display Pressure rollers: Spring-loaded pressure rollers, ø 50 mm, front with limit switch Vacuum pump: 15 kW Machine built to CE guidelines Main switch, hour meter Sound pressure level: ± 80 dB Machine weight: 6,200 kg On request, we can also offer extraction and/or installation!