Ventherm Slikarstvo nakup rabljenega (10)

Stanje: novo, Leto izdelave: 2026, skupna višina: 3.000 mm, skupna dolžina: 4.900 mm, skupna širina: 2.400 mm, volumenski pretok: 3,6 m³/h, vrsta vhodnega toka: trifazni, moč: 1,1 kW (1,50 KM), Oprema: kabina, Wet paint spray booth in enclosure with exhaust and supply air filter, lighting. Lodporvi Risfx Amgsrt

Stanje: novo, Leto izdelave: 2026, Wet-paint spraying/drying booth Internal dimensions: L8000 x W4000 x H3000 mm Air intake: 30,000 m³/h / Air extraction: 30,000 m³/h Paint application temperature: 20°C, adjustable; drying temperature: max. 70°C Indirect gas burner approx. 300 kW (operating range: -10°C to +20°C) Control system integrated in the existing control cabinet Supply air ceiling with G4/EU4 and NF600PA filters Exhaust extraction at floor level via grids, PS50 fiberglass Lighting: recessed wall-mount LED fixtures (4 x 18W), 750 LUX Grid point load capacity max. 750 kg Ledpfxehzbq To Amgsrt

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, skupna višina: 5.600 mm, skupna dolžina: 11.200 mm, skupna širina: 5.100 mm, vrsta vhodnega toka: trifazni, trajanje garancije: 24 meseci, notranja višina: 4.970 mm, notranja dolžina: 11.000 mm, temperatura: 80 °C, notranja širina: 5.000 mm, potreba po zraku: 52.000 m³/h, vhodna napetost: 380 V, ogrevalna zmogljivost: 250 kW (339,91 KM), moč: 45 kW (61,18 KM), gorivo: utekočinjeni naftni plin (LPG), vhodna frekvenca: 50 Hz, poraba energije: 45 kWh, debelina izolacije: 50 mm, nazivna moč: 250 kW (339,91 KM), najv. debelina jeklene pločevine: 2 mm, Oprema: osvetlitev, * Air Treatment Unit: The air treatment unit is a circulation system that supplies the cabin with filtered fresh air and extracts used air during the painting process. It heats the air to 60°C, mixes the exhausted air with 10% fresh air via an automatic multi-damper system, and reheats the air before recirculating it into the cabin. The air is heated by a burner and a heat exchanger, both made of high-grade 304 stainless steel and housed in the fresh air unit. During painting, the air is filtered twice (by pre-filters and ceiling filters) before entering the cabin. The polluted air is also filtered twice (inlet and exhaust filters) before leaving the exhaust unit. Ljdpfx Aswzl Hxsmgjrt Air treatment units are insulated like the sidewalls to minimize heat loss and are protected against possible vibration and noise by rubber seals on the covers. The exhaust air is regulated by a damper in the exhaust duct, contributing to the control of the cabin’s internal pressure. *OPERATING PRINCIPLES OF THE CABIN:* The processes in the cabin are controlled via a control panel, which manages the following steps: *PAINTING PROCESS:* During painting, 100% fresh air is drawn in from outside and passed through the front filters before reaching the plenum at ambient temperature. The air is then discharged via the exhaust unit. Floor filters (paint stop) capture paint particles, and the air passes through the final exhaust filters before being released. *FLASH-OFF PROCESS:* After painting, the cabin runs for another 15 minutes to expel residual solvents and thinners. Fresh air from outside circulates in the cabin during this phase. *DRYING PROCESS* In this phase, 80% of the air flowing through the cabin is heated to 60°C and delivered into the cabin via a plenum. Since 20% of the solvent is released during drying, the solvent is expelled with this air. Industrial paints are typically dried at 60°C; however, the cabin temperature can be adjusted via the control panel as needed. *COOLING PROCESS:* After the 30-minute drying phase, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates into the cabin, and afterwards, the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of the machines and devices integrated into the cabin. The control panel is made of durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Switch Panels: • The control panel contains essential components such as contact breakers, fuses, indicator lights, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • The electrical wiring is designed to allow cabin relocation, if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, skupna višina: 3.500 mm, skupna dolžina: 7.050 mm, skupna širina: 4.100 mm, volumenski pretok: 36.000 m³/h, temperatura: 80 °C, vhodna napetost: 380 V, ogrevalna zmogljivost: 250 kW (339,91 KM), Oprema: kabina, osvetlitev, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. Lodpfx Aoxa H Ewjmgjrt (Alternatively, also available as a separate paint booth with a dedicated dryer). Here, we rely on full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating panels or wall extraction at a position of your choice. If you want to further increase the efficiency of the system beyond heat recovery and stepless control via frequency converter, we are pleased to offer you a sectional control system. This allows you, during repair painting or partial loading of the booth (for example, if you only wish to paint add-on parts), to activate exclusively the section in which the components are located. This way, you can operate with a lower air volume without sacrificing quality, thus saving energy and ultimately real money. Please contact us—we will be happy to demonstrate these options to you. Do you have any questions or suggestions? We are gladly at your service.

Stanje: novo, Leto izdelave: 2025, skupna višina: 4.000 mm, skupna dolžina: 7.000 mm, skupna širina: 3.000 mm, trajanje garancije: 24 meseci, temperatura: 80 °C, potreba po zraku: 36.000 m³/h, vhodna napetost: 380 V, ogrevalna zmogljivost: 345 kW (469,07 KM), moč: 40 kW (54,38 KM), gorivo: utekočinjeni naftni plin (LPG), poraba energije: 40 kWh, izolacijski material: Mineralwolle, debelina izolacije: 50 mm, nazivna moč: 345 kW (469,07 KM), Oprema: osvetlitev, MAIN SPECIFICATION Our spray booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. All processes inside the booth are managed via a PLC system, ensuring consistent adherence to set values. OPERATING PRINCIPLES OF THE BOOTH Processes inside the booth are controlled via an operator panel, which manages the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn from outside, passed through front filters, and directed into the plenum chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) capture paint particles, and the air passes through final exhaust filters before being released. FLASH-OFF PROCESS After painting, the booth continues to run for approximately 15 minutes to extract residual solvents and thinners. During this phase, fresh air from outside continues to circulate within the booth. DRYING PROCESS In this phase, 80% of the air circulating through the booth is heated to 60°C and supplied into the booth through a distribution system. As approximately 20% of the solvent is released during drying, it is expelled together with this air. Industrial coatings are typically cured at 60°C, but booth temperature can be adjusted via the operator panel as needed. COOLING PROCESS After the 30-minute drying phase, the heating coil is deactivated from the operator panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels manage the functions and operation of all machinery and equipment inside the booth. The panel is made of durable galvanized sheet metal and steel sections and is fully enclosed to protect against dust and moisture. Lsdpfx Amswzmcbjgort Electrical devices and control panel: • The control panel contains essential components such as circuit breakers, fuses, signal lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for the command and control connections between the control panel and motors or other electrical equipment. • Electrical wiring is designed to allow for relocation of the booth if required. • Operating equipment uses 380 V 50 Hz, while control devices use 220 V. • The booth operating time can be monitored on the electronic panel for easy maintenance tracking. • Temperature and timer settings for flash-off, intermediate drying, and final drying can be easily programmed to the required values on the electronic control panel’s digital display. • Users can monitor and adjust drying times via the heating thermostat and timer relay.

Stanje: novo, Powder Coating Systems For years, powder coating has been evolving continuously as an alternative to wet painting, and especially recently, it has gained significant importance due to its lower environmental impact, as it does not generate solvent or paint sludge emissions. In particular, the ability to recover unused powder enables especially high efficiency levels. For users, powder coating has the advantage of providing an extremely durable and corrosion-resistant finish that is considerably more impact-resistant than conventional paint. Additionally, reworking, such as grinding or drilling coated parts, poses no problem and will not cause the coating to flake off. Pony Luxury Coating powder coating systems therefore deliver tangible benefits: they are efficient, environmentally friendly, and—true to our tradition—exceptionally flexible. We achieve this through a range of different plant types. Lsdpfjxa Hzxjx Amgjrt Manual Powder Coating Systems Manual powder coating installations are the ideal solution for complex and challenging workpieces. With skilled personnel, there is continuous adaptation to changing circumstances and product sizes. Flexibility is paramount, and these systems also offer a cost-effective entry into the world of powder coating. Large-Capacity Powder Spray Booths No matter how large or demanding your workpieces are—our systems are even larger! Due to the high loads involved in commercial and utility vehicle applications, powder coating has established itself as the ideal solution here. To accommodate ever-larger components, we offer large-capacity powder coating booths that, combined with manual application, place no limits on workpiece size and, when used in conjunction with conveyor systems, can handle any dimension. Automatic Powder Coating Systems If your operation requires high throughput and speed, an automated powder coating installation is your ideal solution. Coupled with conveyor systems, light curtains enable precise part detection and, therefore, exact dosing of powder for optimal efficiency. Of course, we also offer systems equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Flash-Off Dryers The perfect finishing touch for any powder coating process: the curing oven. Our ovens, built to the highest insulation standard, extend our system-wide efficiency to this crucial stage. Detailed temperature control also allows use as a flash-off dryer to dry components after pretreatment. Temperatures of up to 250°C are possible, making these ovens suitable for use as tempering ovens—for example, with hot-dip galvanized parts. Of course, classic use as a powder curing oven is straightforward; optimal air distribution and a visualized control panel prevent overbaking and even enable simultaneous curing of different color shades. Questions or suggestions? We are always happy to help!

Stanje: zelo dobro (rabljeno), Leto izdelave: 2015, Brand: Makor Model: Robospray Twin Ljdpsiu Hbnefx Amgert Year: 2015 Internal length: 670 cm Internal width: 330 cm Internal height: 213 cm Exhaust system: Yes Electrical connection: 400 V Dimensions (L): 11,000 mm Dimensions (W): 4,600 mm Dimensions (H): 4,500 mm Includes: - 2x electric film unwinding units - 1x Beerepoot mobile roller conveyor

Stanje: rabljeno, številka stroja/vozila: 007928, Pozicija 1: Krtačni stroj CEFLA-EASY 2000 + TR2V-FV3 Pozicija 2: Lakirni stroj CEFLA-EASY 2000 + TR2V-FV3 Pozicija 3: Sušilec laka CEFLA-EASY 2000 + TR2V-FV3 Lredpewu Ackofx Amgst

Stanje: rabljeno, številka stroja/vozila: 007466, Pozicija 1: Prenos SUPERFICI-BRAVOROBOT P1 Pozicija 2: Krtačilni stroj SUPERFICI-BRAVOROBOT P1 Lsdpfx Ajwu Aa Nsmgort Pozicija 3: Pršilni robot SUPERFICI-BRAVOROBOT P1 Pozicija 4: Sušenje laka SUPERFICI-BRAVOROBOT P1 Pozicija 5: Prenos SUPERFICI-BRAVOROBOT P1 Pozicija 6: Prenos SUPERFICI-BRAVOROBOT P1

Stanje: rabljeno, številka stroja/vozila: 008157, Položaj 1: Čistilni stroj GIARDINA-1VE - 300 Položaj 2: Naprava za brizganje barve GIARDINA-1VE - 300 Lodsw Sdu Uspfx Amgert Položaj 3: Nakladalnik GIARDINA-1VE - 300