Mütek Systemtechnik Hawk-Eye nakup rabljenega (3.293)

Stanje: novo, Leto izdelave: 2026, Premer: 160 mm Za doplačilo je možno dobiti tudi v premerih: 180, 200, 250, 300 mm; dodatni premeri na zahtevo. Lrjdpfxechuvrs Amljn Zelo robustna industrijska izvedba. Idealno za ločevanje žebljev/kovinskih delov iz materialnih tokov. Na primer za uporabo po lesnem drobilniku. Vključno s 3 izjemno zmogljivimi magneti. * Po želji je mogoče vgraditi do največ 6 magnetov v element – doplačilo za vsak dodatni magnet + 49 € - Za doplačilo so na voljo tudi neodim magneti namesto feritnih. Vaše prednosti: + Izjemno velika revizijska vrata s tesnilom za lahko odstranjevanje žebljev + Stabilno hitro zapiranje + Izdelano v Nemčiji Revizijska vrata/odprtina: 35x18 cm Vgradna dolžina je lahko različna

Leto izdelave: 2026, stanje: novo, *Only the neodymium overband magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have extremely high holding force and cannot be compared to ferrite magnets. Extremely high separation efficiency, depending on the material height and input material. Probably the most compact overband magnet on the market. Competitors often use the less powerful ferrite magnets to save costs. Approximate dimensions: Length: 104 cm Width: 22 cm Height: 28 cm (at the motor) *Without control system Surcharge for simple manual start/stop control: + €495 A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600 x 68 x 36.5 mm * Over a length of 600 mm, nails are attracted and discharged sideways once outside the magnetic zone. Lodpfxodubpuo Amlsrn This overband magnet should be installed approx. 7–10 cm above the material flow. *Mounting/suspension to be provided by the customer *depending on the maximum length of the metal pieces. Ideal for separating nails from wood chips. Optionally used in a single-shaft shredder with extraction. Requirements: * Your belt width or effective inner width (of the existing conveyor belt) should ideally be less than 55 cm *Suitable for separating nails from material flows less than 12 mm high, as well as chip lengths less than 25 mm. ----- Optional at extra cost: Cross and incline conveyor demo units from €8,770 net

Stanje: novo, Leto izdelave: 2026, Extremely powerful industrial magnet for iron separation Special price: €990 net (Shipping €14.90 net) *Please refer to image 2 for construction lengths The active side features a stainless steel end plate (material 1.4301). Threaded holes are provided on the reverse for mounting *Handle available on request The block magnet systems can be used up to a maximum operating temperature of +100°C. The magnet surface should be cleaned regularly of captured iron parts. Attraction heights for all types, e.g.: For an M5 steel nut approx. 60 mm Lodstqfhxopfx Amljrn For an M5 x 30 screw approx. 100 mm Mounting Example 1: Mounted above a conveyor belt, the iron parts "jump" onto the magnetic contact surface. Mounting Example 2: Installed in a pipeline system in direct contact with the material flow. For high separation security, a cascade arrangement of several block magnets in series is possible. Installation and safety instructions: When handling, even during unpacking and later mounting, ensure that no loose iron parts, such as tools or screws, are nearby. The magnetic force is so strong that painful injuries can occur if fingers get caught between iron parts and the active surface. No steel parts should be present within a minimum distance of 400 mm underneath the active surface.

Stanje: novo, Leto izdelave: 2026, Our best-selling briquetting press – the classic choice. + Proven, simple technology for extremely low failure rates + 25 years of experience, ongoing development, and expertise + Several thousand machines in operation with satisfied customers + Outstanding price-performance ratio Optional extras (available at additional cost): *Surcharge for fill level sensor, enabling automatic operation: + €995 net *Surcharge for large pre-compression chamber + €970 (Recommended for very light materials such as straw, increases machine width by 13 cm) Briquette diameter: 50 mm Front bushing: 50 mm Max. briquette stroke: 40 mm Optimal briquette stroke: 40 mm Throughput (material dependent): up to 60 kg/h* *Depending on bulk density *Based on a bulk density of 200 kg/m³ Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1,680 mm Width: 1,100 mm Height: 1,500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1,000 mm Silo capacity: approx. 0.7 m³ Pump output: 37 liters Hydraulic pre-compressor Press tongs cooling option: No Hydraulic oil cooling option: Yes Fill level monitoring option: Yes CE compliant Raw material requirements: - Moisture content (atro) must be between at least 6% and max. 18% - Maximum chip length 15 mm Lrjdpfx Aegl Nlmemljn - Installation temperature: Tempered room, at least +5°C - Customer must provide protection against hydraulic oil loss - Material feed must be free from metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may result

Stanje: novo, Leto izdelave: 2025, Še en stroj na voljo takoj! Briketirka s krmilnikom PLC in avtomatiko za dolžino briketa Zmogljivost: do največ 60 kg/h Briket: 50 mm valjaste oblike Motor: 5,5 kW Dimenzije: 1.900 x 1.350 x 1.410 mm Teža: pribl. 860 kg. Lrjdpfx Aev Rpxlemljn Zahteve: Izhodni material idealno krajši od 25 mm dolžine ostružkov Vsebnost vlage 6–12 % ATRO Stroj je primeren za občasno delovanje. Npr. do 2,5 ure briketiranja, 1 ura premora itd. Če naj stroj deluje neprekinjeno več kot 2,5 ure, je treba priključiti opcijsko hlajenje.

Stanje: novo, Leto izdelave: 2026, * Optional features available at extra cost, see below * Production time approx. +/- 6 months The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are characterized by their robust construction, ensuring consistent briquette quality during continuous operation. The compaction process takes place without the addition of binding agents—solely via hydraulic pressing force. Depending on the material, the input material volume can be reduced by up to 90%. The standard silo holds approx. 0.5 m³, but larger silos or special containers for installation below an existing extraction and filter system as a complete disposal unit are also available. Depending on customer requirements, MPP NEM individual machines can be combined into a complete system. The chip hopper of the press can be loaded manually, via conveyor belt, via dust extractor, or with a tilting container trolley. For systems intended for fully automatic operation, the use of a lift-and-tilt device, in conjunction with a shredder, is recommended. The MPP NEM briquetting presses are designed for the production of briquettes from homogeneous material. Ljdogfm Ryspfx Amlorn The length of a briquette depends on the model and ranges from 40 to 80 mm, and the diameter varies by type (50, 65, or 70 mm). To recover emulsions, the briquetting press can be equipped with a drip tray, allowing coolants, cutting fluids, and lubricants to be collected and recovered. Non-ferrous metal chips up to approx. 20 mm in length are filled into the briquetting press's feed hopper. An agitator is built into the bottom of the hopper to prevent bridging and feed the material into the pre-compaction chamber. In this chamber, a hydraulic ram pre-compacts the material and pushes it into the press block. The main press cylinder then compresses the material against a vertical slide until the set pressing pressure is reached. The vertical cylinder subsequently lifts, and the finished, stable briquette is ejected. The more homogeneous the input material, the more uniform the briquette lengths. Advantages of briquette production include: - Volume reduction by up to 90% - Emulsion recovery - Cost savings on storage and transport - Economical disposal - Profitable resale Briquetting Press NEM 900: For briquetting aluminum chips Throughput capacity: up to 350 kg/h max (material-dependent; chip length less than 10 mm) Last test with aluminum chips < 18 mm: approx. 260 kg/h *More details available after a free test with your material. Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm Technical data: Total connected load: approx. 31 kW Continuous operation: approx. 22 kW 400 Volt / 50 Hz / 3-phase Pump: 120 + 60 litres per minute Silo: 1 m³ Silo diameter: 1200 mm Including agitator Oil tank: 600 litres Dimensions (LxWxH): 2500 x 1700 x 1730 mm Weight: 2250 kg Hydraulic pre-compaction via ram Main press cylinder Vertical cylinder Prepared for connection to a cooling unit

Stanje: novo, Leto izdelave: 2026, Production time for the machine approx. 3.5 months Very robust machine with high pressing force - Also suitable for already producing a saleable briquette quality, depending on the material. The large-dimensioned press cylinder and the 65 mm briquette diameter make this possible. Our best-selling briquetting press series + Proven, simple technology for extremely low susceptibility to faults + 25 years of experience, ongoing development and expertise + Several thousand machines in use with satisfied customers + Good price-performance ratio Options: Surcharge for cooling unit + €3,995 net (can also be retrofitted) * cools the pressing tongs (important from 3.5 hours of operation) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a stretch. Large pre-compactor chamber + €1,975 net Recommended for lightweight input materials such as planing shavings Customs tariff number: 84793010 Briquette diameter: 65 mm Front bushing: 65 mm Max. briquette stroke: 50 mm Optimal briquette stroke: 50 mm Capacity (depending on material): up to 110 kg/h* Last test: approx. 87 kg/h *Depending on bulk density *Based on a bulk density of 200 kg per cubic meter . Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1,925 mm Width: 1,100 mm Height: 1,500 mm Weight: 800 kg Oil volume: 110 liters Ledpfxjffh Ate Amlorn Silo diameter: 1,000 mm Silo capacity: approx. 0.7 m³ Pump: 37 liters Hydraulic pre-compactor Press tong cooling option: yes, with special accessory of coolable press tongs Cooling of the press tongs via a water tank (must be supplied by the customer) Hydraulic oil cooling option: yes Fill level monitoring option: yes Continuous briquette option: yes (material-dependent) CE compliant . Requirements for the raw material: - The moisture content (oven dry basis) must be at least 6% and no more than 18% - Maximum chip length: 15 mm - Installation temperature: heated room of at least +5°C - The feed material must be free of metal and mineral contaminants such as sand, stones, etc. Damage to the pressing tools and/or increased wear may result

Stanje: kot nova (razstavni stroj), Leto izdelave: 2025, Special price for our demonstration machine Another unit available immediately (ex works Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of residual wood and pallet offcuts. Pallets must be pre-cut with a jigsaw or chainsaw so that they fit upright into the hopper—see image 2. Ideally, dimensions of approx. 40x20x20 cm allow the wood to lie flat on the ram base, which is the most efficient way for the machine to process it. A hydraulically driven ram at the bottom of the shredder pushes the wood against the rotor, with the pressure adjusted according to load. Material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour (*depending on screen size and material preparation). *Discharge conveyor and overband magnet available at additional cost. + Powerful 18.5 kW motor + Concave blades + Heavy-duty large gearbox + Special load-dependent ram control system Commodity code: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15 pieces, multiple-use (reversible) Option: Double blade row + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutting chamber opening: 630 x 820 mm Fill volume: approx. 0.6 m³ Hydraulically actuated ram Screen perforation as requested (10–30mm) Extraction outlet Ø 160 mm Weight: approx. 1,300 kg (depending on configuration) Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm Moisture content: < 30% oven dry Standard equipment includes: - V-rotor for maximum throughput - Control cabinet with Siemens PLC - Automatic star-delta starter - High-speed hydraulics - Automatic shut-off in case of rotor idle - 70–90 rpm for high throughput - Cycle control to avoid idle times - Performance-boosting step control of the hydraulic ram - Pertinax guides for hydraulic ram - Vibration-damping machine feet - CE compliant - MADE IN GERMANY Shredder options: - Raise shredder by 30 cm (preparation for conveyor) + €2,080 net - Angled conveyor belt + €8,770 net Horizontal part: 1200 mm Inclined part: 2500 mm Adjustable angle: 0–60 degrees Discharge height: approx. 2000 mm (+/- 100 mm) - Overband magnet + €5,980 net - Control for conveyor and overband magnet + €2,750 net (Start/stop synchronized with shredder) - Extended hopper + €940 net - Eco rings: + €1,980 net (recommended for more than 15% hardwood content) - Special scraper + €990 net (recommended for veneer or paper) - Double blade row + €995 net Lredpfx Amedwktkjlsn Raw material requirements: - Moisture content (oven dry) must be below 30% - Metal or mineral contaminants such as sand, stones, etc., increase wear.

Stanje: dober (rabljeno), Clean air extraction Used machine, good condition Pictures to follow Mobile Jet 160 Lredpfxorb D Nj Amlsn Connection: 160 mm Fan: 2.2 kW Airflow: 1,850 m³/h / 400 V

Stanje: kot nova (razstavni stroj), Leto izdelave: 2024, The ideal machine for shredding cables including optimized cutting geometry approx. 9 operating hours Motor: 18.5 kW; 400 V - 50 Hz - 3 phase, Blades: 14 pieces, 40x40 mm, reversible multiple times, Rotor diameter: 260 mm, Control unit: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume: approx. 0.6 cbm, Hydraulically operated pusher, Screen perforation as required (15–40 mm), Extraction port Ø 160 mm, Weight: approx. 1,300 kg, Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm The following options available at extra cost: - Double knife row + €1,990 net (28 instead of 14) - Surcharge for sectional floor, 4-sided + €2,170 net (Prevents pusher blockage. Recommended when shredding plastics, paper, veneer with thickness < 3 mm). - Raise shredder by 30 cm (ready for conveyor belt) + €1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €6,980 net Lrsdpfx Aogmfa Asmlen - Conveyor belt and overband magnet controls + €2,750 net (Start and stop synchronized with the shredder) Bea9ia3l27 Raw material requirements: - Mineral contamination such as sand, stones, etc., leads to increased wear. We are pleased to offer a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can ship your material to us via freight forwarder, and we will document the test with photos and videos.

Stanje: kot nova (razstavni stroj), Demonstracijska naprava s 7 delovnimi urami na voljo takoj (iz tovarne Neckartailfingen) Šreder MRZ 830 Carinska tarifna številka: 84659600 Vhodna odprtina 800x1000 mm Motor: 18,5/22 kW; 400 V - 50 Hz - 3 faze Noži: večkrat vrtljivi Hidravlično gnani pomik Velikost mreže po izboru (10 - 40 mm) Teža cca 1.600 kg Dimenzije (d x š x v) cca 2290 x 1420 x 1750 mm Turbo sklopka Serijska oprema vključuje: - avtomatski zvezda/trikot zagon - hitra hidravlika - avtomatski izklop pri prostem teku rotorja - Hitrost 70-90 obr/min za visoko zmogljivost pretoka - Intervalno krmiljenje za preprečevanje prostega teka - Učinkovito krmiljenje gibanja hidravličnega pomika - Vodila iz pertinaksa za hidravlični pomik - Vibracijsko dušeča podporna stopala - V skladu s CE . Razrezovalnik je zasnovan za drobljenje neobdelanega lesa, ivernih in MDF plošč ter drugih materialov po testiranju in odobritvi proizvajalca . Vključeno: - Dvig šrederja za 30 cm (priprava za transportni trak) Dodatne možnosti šrederja: - Kotni transportni trak + 8.770 € netto Horizontalni del: 1200 mm Naraščajoči del: 2500 mm Kot: nastavljiv 0-60 stopinj Ledpfov Sqrpox Amlsrn Izhodna višina: cca 2000 mm +/- 100 mm - Nadtrakovni magnet + 6.780 € netto - Krmiljenje transportnega traku in nadtrakovnega magneta + 2.750 € netto (Zagon in zaustavitev vedno sinhronizirana z drobilcem) . Zahteve za vhodni material: - Vsebnost vlage (atro) mora biti pod 30 % - Kovina in mineralne nečistoče kot so pesek, kamenje itd. povzročajo večjo obrabo

Stanje: novo, Leto izdelave: 2026, Production time approx. +/- 4 months. The ideal machine, for example, for shredding pallets and wood waste. * prepared for extraction, see pictures 4 and 5 without additional accessories such as -exhibited hopper or -conveyor belt cutout Commodity code: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 phase incl. turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3 phase Knives: 76 pieces, reversible multiple times Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control system: Siemens S7-1200 PLC Hopper opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 cbm Hydraulically operated pusher Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (LxWxH) approx. 2765 x 2520 x 1730 mm Turbo coupling Standard equipment includes: - V-rotor for maximum throughput - 2nd row of knives on rotor - Control cabinet with Siemens PLC control system - Automatic star/delta start - Fast hydraulic system - Automatic shutdown when rotor is idling Lrodpfed Hkqhsx Amlsn - Rotation speed 70-90 rpm for high throughput - Cycle control to avoid idle time - Performance-enhancing step control for hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration dampening machine feet - CE compliant The shredder is designed for shredding natural wood, chipboard and MDF, other materials upon testing and approval by the manufacturer. Requirements for raw material: - Moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 100 kg, skupna višina: 1.660 mm, Leto izdelave: 2025, vhodna napetost: 230 V, laserska moč: 20 W, valovna dolžina laserja: 1.064 nm, vrsta hlajenja: zrak, vrsta vhodnega toka: Klimatska naprava, Laser for Product Marking – The universally applicable laser marking system LAS 28 from Systemtechnik Hölzer GmbH is suitable for a very wide range of marking applications. With the integrated fiber laser, you can mark nearly all materials such as steel, carbide, aluminum, and plastics. Depending on requirements, the system can be equipped with a 20, 30, or 50 watt fiber laser. In many industries, laser technology has become indispensable for durable marking. The powerful laser software allows you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks and without extensive programming knowledge. The software increases serial and article numbers automatically after initial setup. Furthermore, the software can extract data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. Lrjdowkpwaopfx Amljn Standard equipment includes a laptop with a holder and Windows operating system. Optionally, the LAS 28 laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Additional options, such as side extensions for marking long parts, are also available. Made in Germany • Fiber laser 20W (optional: 30W, 50W) • Wavelength 1064nm • Marking field size 150x150mm (optional: 200x200mm) • Optional: rotary axis (3-jaw chuck) • Optional: digital height measuring system • Optional: extraction system (incl. activated carbon filter) • Optional: autofocus system – system for automatic focus distance determination • Signal tower for operating status display • Marking software EZCAD (optional additional laser software) • Pilot laser (simple preview, contour preview) • Focus finder (easy focus adjustment) • Max. component height approx. 270mm • Electrically adjustable Z-axis (work level adjustment) • Frame made of aluminum profile • 230V connection • Air cooled • Laptop with Windows operating system • Dimensions: 800 x 600 x 1660 mm (L x W x H) • Weight: approx. 80 kg

Leto izdelave: 2026, stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 120 kg, skupna dolžina: 900 mm, skupna širina: 1.500 mm, skupna višina: 2.050 mm, vhodna napetost: 230 V, laserska moč: 30 W, valovna dolžina laserja: 1.064 nm, natančnost ponavljanja: 0,01 mm, vrsta vhodnega toka: Klimatska naprava, vrsta laserja: vlakenski laser, Oprema: USB priključek, osvetlitev, The universally applicable LAS 28 XLe laser marking system by Systemtechnik Hölzer GmbH is suitable for a wide range of marking applications. The integrated fiber laser allows you to mark almost any material, such as steel, hard metal, aluminum, and plastics. Depending on your requirements, the system can be equipped with a 20, 30, or 50-watt fiber laser. For permanent marking, the use of a laser has become indispensable in many industries. The powerful laser software enables you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks and without extensive programming knowledge. The software automatically increments serial and item numbers after initial setup. Additionally, the software can import data (variable information such as drawing numbers, project names, etc.) from existing tables and automatically transfer them into predefined fields. The use of a handheld scanner is also possible. Standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the LAS 28 XLe laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as side cantilevers for marking long parts, movable Z-axis, drawer systems, etc., are available upon request. Made in Germany Fiber laser: 30W, 20W, or 50W • Laser class 1 • Wavelength: 1064 nm Lrodpoyxccrofx Amljn • Marking field size: 150x150 mm (larger optional) • Marking software EZCAD in German/English • Optional: rotary axis (3-jaw chuck) • Optional: digital height measurement system • Optional: autofocus system – automatic focus distance determination • Optional: extraction unit (including activated carbon filter) • Pilot laser (easy preview, contour preview) • Focus finder (easy focus adjustment) • Signal tower for operating status display • Max. component height approx. 300 mm • Electrically adjustable Z-axis • Integrated PC with Windows OS • IPS PCAP touchscreen and height-adjustable keyboard platform • Aluminum profile frame • Air-cooled • Door width approx. 700 mm / door height (pass-through): 400 mm • Connection: 230V • Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) • Weight: approx. 120 kg

Leto izdelave: 2026, stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 45 kg, skupna dolžina: 350 mm, skupna širina: 605 mm, skupna višina: 1.080 mm, vhodna napetost: 230 V, laserska moč: 20 W, valovna dolžina laserja: 1.064 nm, dolžina območja skeniranja: 70 mm, širina območja skeniranja: 70 mm, vrsta hlajenja: zrak, vrsta vhodnega toka: Klimatska naprava, vrsta laserja: vlakenski laser, The mobile LAS 23 portable laser is distinguished by its compact design. Small, handy, and equipped with custom-made attachments that can be individually exchanged using a quick-change system. Its mobile base allows it to be conveniently moved to the workpieces to be marked. This makes it suitable for both large and heavy as well as small workpieces. The powerful laser software enables texts, numbers, 2D codes, QR codes, and logos to be created with just a few clicks and without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after the initial setup. Additionally, it can read data (such as variable information like drawing numbers, project names, etc.) from existing tables and automatically transfer them to predefined fields. Using a handheld scanner is also possible. Made in Germany • Fiber laser 20W (optional: 30 Watt, 50 Watt) • Laser class 1 • CE compliant, according to EU regulations • Wavelength 1064nm • Marking field size 70x70mm (optional: 110x110mm) • Status signal light (integrated in handheld unit) • Marking software EZCAD • Connection 230V • Air-cooled Ljdpou Smcbefx Amlorn • Laptop with Windows operating system • Dimensions: 350 x 605 x 1080mm (LxWxH) • Weight: approx. 45 kg • Weight of portable laser unit (handpiece): 2.8 kg • Fiber optic cable: approx. 2.50 m • Integrated extraction system

Leto izdelave: 2026, stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 120 kg, laserska moč: 30 W, valovna dolžina laserja: 1.064 nm, dolžina območja skeniranja: 150 mm, širina območja skeniranja: 150 mm, vrsta hlajenja: zrak, vrsta vhodnega toka: Klimatska naprava, vrsta laserja: vlakenski laser, The universally applicable LAS 28 XLe laser marking system from Systemtechnik Hölzer GmbH is suitable for a wide range of marking applications. With the integrated fiber laser, you can mark almost any material, including steel, carbide, aluminum, and plastics. Depending on your requirements, the system can be equipped with a 20, 30, or 50 watt fiber laser. The use of lasers for permanent marking has become indispensable in many industries. The powerful laser software allows you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks and without extensive programming knowledge. Lot and article numbers can be automatically incremented by the software after prior configuration. Additionally, the software can read data (such as drawing numbers, project names, etc.) from existing tables and automatically transfer it to predefined areas. The use of a handheld scanner is also supported. Standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the LAS 28 XLe laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Additional options, such as side arms for marking long parts, movable Z-axis, drawer systems, etc., are available. Programmable, software-controlled axes (X, Y, Z axes) and database connectivity are also possible. Made in Germany Ljdpfx Ajwkpvvsmlern Fiber laser: 30 W, 20 W or 50 W • Laser class 1 • Wavelength: 1064 nm • Marking field size: 150x150 mm (larger optionally available) • Marking software: EZCAD in German / English • Optional: rotary axis (3-jaw chuck) • Optional: digital height measurement system • Optional: extraction system (incl. activated carbon filter) • Optional: autofocus system – for automatic focal distance determination • Optional: programmable X, Y, and Z axes (software-controlled) • Pilot laser (easy preview, contour preview) • Focus finder (for easy focus adjustment) • Signal beacon for operating status display • Max. workpiece height approx. 300 mm • Electrically adjustable Z-axis • Integrated PC with Windows operating system • Height-adjustable monitor and keyboard support • Frame made of aluminum profiles • Air cooled • Door width approx. 700 mm / Pass-through door height: 400 mm • 230 V power connection • Dimensions: approx. 900 x 800 x 1900 mm (L x W x H) • Weight: approx. 120 kg

Leto izdelave: 2026, obratovalne ure: 1 h, stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 560 kg, skupna dolžina: 1.870 mm, skupna širina: 1.040 mm, skupna višina: 1.550 mm, priključek za stisnjen zrak: 6 letvica, natančnost pozicioniranja: 0,01 mm, natančnost ponavljanja: 0,01 mm, največja hitrost vrtenja: 60.000 obr/min, vrsta vhodnega toka: trifazni, Polavtomatsko razrezovanje uporab – Osnovni stroj s paralelnim preklopnikom Dinamični uporabni rezalnik LOW 4322 je posebej primeren za srednje do velike količine izdelkov in izpolnjuje naraščajoče zahteve v proizvodnem procesu. Uporabne plošče iz različnih materialov se s pomočjo žaginih in rezkalnih tehnik z malo prahu in napetosti razrezujejo z najvišjo produktivno prilagodljivostjo, natančnostjo in zmogljivostjo. Visoko dinamične linearne motorske osi, orodja in prijemala izpolnjujejo najvišje standarde kakovosti, s čimer zagotavljajo dolgo življenjsko dobo in zanesljivost rezalnika. Izdelano v Nemčiji Polavtomatsko razrezovanje uporab – rešitve po meri Uporabni rezalnik LOW 4322 omogoča hitro menjavo izdelkov ob hkratnem ohranjanju kratkih časov rezanja in rokovanja. Vstavljanje uporabnih tiskanih vezij poteka s paralelnim preklopnikom, prijem in pritrditev s tehnologijo zatičnega vpenjanja, po potrebi v kombinaciji z vakuumskimi priseski. Lsdpfx Aext Dmxemlorn Stroj je opremljen z: • Grednim in kolutnim orodnim razrezovalnim modulom na Z-osi (samodejno vrtljiv 0–90°) • X-Y križni vbodni modul v tehnologiji linearnega motorja z visoko ločljivim merilnim sistemom • Dvojni nakladalni modul, izdelan kot paralelni preklopnik, ločeno levo in desno s pomičnimi vrati • Okvir iz aluminijastih profilov z dvema servisnima vratoma – levo in desno • Osnovni modul standardnega vision sistema za Teach-In programiranje (kamera 400 × 330 mm) • Delovno območje 420 × 330 mm • Samodejna obdelava dolžine rezkarjev (samo v kombinaciji z modulom za gredni rez) • Oddaljeno vzdrževanje/podpora preko oddaljene povezave (TeamViewer) ali s strani stranke • Touch IPC z operacijskim sistemom Windows • Lasersko merjenje osi z dokumentacijo • Ionizacija zraka • Kontrola loma rezkarjev samo za gredne rezkarje • Priprava na vakuumsko vpenjalno tehniko • ESD-zaščitno steklo in drsna vrata Opcijsko je mogoče naknadno ponuditi tudi enoto za odsesavanje prahu. Visoka zmogljivost rezalnika z vgrajenim žaginim ali rezkalnim modulom, polavtomatsko obdelavo dolžine rezkarja, slikovno podprtim Teach-In kamerami in dvema enostavno naloženima napravama za tiskanine se lahko razširi z veliko prilagodljivimi rešitvami in dodatno opremo (npr. vision sistem). Natančna laserska meritev osi pred zagonom je pri vseh linijskih in samostojnih uporabniških sistemih Systemtechnik Hölzer del individualne storitve za stranke.

Leto izdelave: 2026, stanje: novo, Funkcionalnost: popolnoma funkcionalen, skupna masa: 45 kg, vhodna napetost: 230 V, vhodna frekvenca: 50 Hz, laserska moč: 30 W, valovna dolžina laserja: 1.064 nm, dolžina območja skeniranja: 110 mm, širina območja skeniranja: 110 mm, vrsta hlajenja: zrak, vrsta vhodnega toka: Klimatska naprava, vrsta laserja: vlakenski laser, The LAS 22 is a compact tabletop device with a small working area, ideally suited for small components. Due to its compact design, the system is highly practical and can be used anywhere. Lsdowkpxkspfx Amlern The device is very easy to operate even without programming skills. With the powerful laser software, texts, numbers, 2D codes, QR codes, and logos can be created with just a few clicks and without extensive programming knowledge. Serial and item numbers are automatically incremented by the software after prior configuration. Additionally, the software can read data (variable information such as drawing numbers, project names, etc.) from existing tables and automatically transfer them to predefined fields. The use of a handheld scanner is also possible. Standard equipment includes a laptop with Windows operating system and laser software. Optionally, the LAS 22 laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. - Fiber laser 30 watt (optionally: 20 watt) - Laser class 1 - Wavelength 1064nm - Marking field size 110 x 110 mm - Marking software EZCAD in German / English - Pilot laser (simple preview/contour preview) - Focus finder (easy focusing) - Max. component height approx. 95 mm - Grid holes for fixtures - Clamping surface 310 x 190 mm - Electrically adjustable Z-axis - Electric door with pinch protection stop - Optional: extraction system (incl. activated carbon filter) - Optional: 3-jaw chuck for marking cylindrical parts - Welded steel sheet construction - Connection 230V - Air-cooled - Laptop with Windows operating system (German or English) - Dimensions (LxWxH): 600 x 400 x 690 mm - Weight: approx. 45 kg

Stanje: novo, Leto izdelave: 2026, Funkcionalnost: popolnoma funkcionalen, vhodna napetost: 230 V, vrsta vhodnega toka: Klimatska naprava, laserska moč: 30 W, vrsta hlajenja: zrak, skupna širina: 1.550 mm, skupna višina: 2.050 mm, skupna dolžina: 900 mm, skupna masa: 120 kg, vrsta nastavitve višine: električni, širina odprtine vrat: 700 mm, višina odprtine vrat: 400 mm, potrebna širina: 1.550 mm, potrebna višina: 2.100 mm, valovna dolžina laserja: 1.064 nm, temperatura okolja (min.): 15 °C, okoljska temperatura (maks.): 35 °C, The universally applicable LAS 28 XLe laser marking system from Systemtechnik Hölzer GmbH can be used for a wide range of marking applications. With the integrated fiber laser, you can mark almost all materials such as steel, carbide, aluminum, and plastics. Depending on requirements, the system can be equipped with a 20, 30, or 50 watt fiber laser. In many industries, the use of a laser has become indispensable for permanent marking. The powerful laser software allows you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks and without extensive programming knowledge. The software can automatically increment serial and part numbers after prior setup. In addition, it can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined fields. Use of a handheld scanner is also possible. Lrjdpfx Aewlc Stjmljn The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the LAS 28 XLe can be fitted with a rotary axis (3-jaw chuck) for marking cylindrical components. Further options, such as lateral extensions for marking long parts, motorized Z-axis, drawer systems, etc., are also available. Made in Germany Fiber laser 30 Watt (optionally 20 Watt or 50 Watt) • Class 1 laser • Wavelength 1064 nm • Marking field size 150x150 mm (optionally larger) • Signal lamp to indicate operating status • Optional: rotary axis (3-jaw chuck) • Optional: extraction system (incl. activated carbon filter) • Optional: digital height measurement system • Optional: autofocus system for automatic determination of focus distance • Marking software EZCAD available in German / English (other software available on request) • Pilot laser (simple preview, plain text preview) • Focus finder (easy focus adjustment) • Max. part height approx. 300 mm • Electrically adjustable Z-axis • Integrated PC with Windows operating system • IPS PCAP touch screen and keyboard tray, height adjustable • Frame made of aluminum profile • Air-cooled • Door width approx. 700 mm / door height (pass-through): approx. 400 mm • Power supply 230V • Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) with monitor holder approx. 1500 x 800 x 1900 mm (LxWxH) • Weight: approx. 120 kg

Stanje: novo, Leto izdelave: 2026, Funkcionalnost: popolnoma funkcionalen, vhodna napetost: 230 V, laserska moč: 30 W, vrsta hlajenja: zrak, skupna širina: 1.550 mm, skupna višina: 2.050 mm, skupna dolžina: 900 mm, skupna masa: 120 kg, vrsta nastavitve višine: električni, širina odprtine vrat: 700 mm, višina odprtine vrat: 400 mm, dolžina območja skeniranja: 150 mm, širina območja skeniranja: 150 mm, temperatura okolja (min.): 15 °C, okoljska temperatura (maks.): 35 °C, The LAS 28 XLe laser marking system from Systemtechnik Hölzer GmbH is a universally applicable, high-performance marking solution designed for industrial applications. It is suitable for precise and permanent marking of a wide range of materials including metals such as steel, aluminum, and hard metals, as well as plastics. The integration of a fiber laser ensures high marking quality while keeping maintenance requirements to a minimum. The system can be configured with fiber lasers in power classes of 20 W, 30 W, or 50 W, enabling optimal adaptation to different requirements concerning material type, marking depth, and cycle time. In many industrial sectors, the use of this technology is indispensable due to the durability and abrasion resistance of the markings. The included laser software allows the creation and positioning of content such as texts, numbering, 2D codes (e.g., DataMatrix), QR codes, and logos. Automatic serialization logic enables the generation of consecutive serial numbers without manual intervention. Additionally, the software supports importing and processing of external data sources (e.g., Excel spreadsheets) for variable contents like drawing numbers or project names. Integration of a hand scanner for data capture is optionally available. By default, the LAS 28 XLe is delivered with an integrated industrial PC (Windows-based) and fully installed laser software. Various options are available to expand its functionality, including a rotary axis (3-jaw chuck) for marking cylindrical components, side arms for processing long parts, a motorized Z-axis, and modular drawer systems for part feeding. Made in Germany Fiber laser: 30 W, 20 W, or 50 W • Laser class 1 • Wavelength: 1064 nm • Marking field size: 150 x 150 mm (optionally larger) • Signal tower for operating status display • Optional: Rotary axis (3-jaw chuck) • Optional: Extraction system (incl. activated carbon filter) • Optional: Digital height measurement system • Optional: Autofocus system – automatic focus distance determination • Optional: Side arms for large components (single or double-sided) • Optional: Programmable X, Y, and Z axes (software controlled) • EZCAD marking software (German/English) • Pilot laser (easy preview, plain text preview) • Focus finder (simple focus adjustment) • Max. component height approx. 300 mm • Electrically adjustable Z-axis • Integrated PC with Windows OS • Height-adjustable monitor and keyboard shelf • Aluminium profile frame • Air-cooled • Door width approx. 700 mm / Door height (pass-through): approx. 400 mm • Power supply: 230 V • Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) Lrodpfx Amjwkpx Relsn with monitor holder: approx. 1500 x 800 x 1900 mm (LxWxH) • Weight: approx. 120 kg

Stanje: novo, Leto izdelave: 2026, Funkcionalnost: popolnoma funkcionalen, laserska moč: 30 W, vrsta hlajenja: zrak, skupna masa: 45 kg, vrsta nastavitve višine: električni, dolžina območja skeniranja: 110 mm, širina območja skeniranja: 110 mm, valovna dolžina laserja: 1.064 nm, temperatura okolja (min.): 15 °C, okoljska temperatura (maks.): 35 °C, The LAS 22 is a compact desktop unit with a small working area, ideal for marking small components. Thanks to its compact design, the system is extremely user-friendly and can be used virtually anywhere. The universally applicable LAS 22 laser marking system from Systemtechnik Hölzer GmbH is suitable for a very wide range of marking applications. With the integrated fiber laser, you can mark almost any material, such as steel, carbide, aluminum, and plastics. Depending on requirements, the system can be equipped with a 20 or 30-watt fiber laser. In many industries, laser marking is essential for permanent markings. Lrjdpfx Aouy H Nqomlsn The powerful laser software allows you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks, without requiring extensive programming knowledge. The software can automatically increment serial and article numbers after initial configuration. Moreover, the software can read data (variable information such as drawing numbers, project names, etc.) from existing tables and automatically transfer it to predefined fields. Using a hand scanner is also possible. Standard equipment includes a laptop with Windows operating system and laser software. Optionally, the LAS 22 laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. - Fiber laser 30 watt (optional: 20 watt) - Laser class 1 - Wavelength: 1064 nm - Marking field size: 110 x 110 mm - Marking software EZCAD in German / English - Pilot laser (easy preview, contour preview) - Focus finder (simple focusing) - Max. workpiece height approx. 95 mm - Grid holes for fixtures - Clamping area: 310 x 190 mm - Electrically adjustable Z-axis - Electric door with pinch protection stop - Optional: extraction system (incl. activated carbon filter) - Welded steel sheet construction - Connection: 230 V - Air-cooled - Laptop with Windows OS (German or English) - Dimensions (LxWxH): 600 x 400 x 690 mm - Weight: approx. 45 kg

Stanje: novo, Leto izdelave: 2026, Funkcionalnost: popolnoma funkcionalen, vhodna napetost: 230 V, vrsta vhodnega toka: Klimatska naprava, laserska moč: 30 W, vrsta hlajenja: zrak, skupna širina: 400 mm, skupna višina: 690 mm, skupna dolžina: 600 mm, skupna masa: 45 kg, vrsta nastavitve višine: električni, dolžina območja skeniranja: 110 mm, širina območja skeniranja: 110 mm, potrebna višina: 900 mm, valovna dolžina laserja: 1.064 nm, temperatura okolja (min.): 15 °C, okoljska temperatura (maks.): 35 °C, vhodna frekvenca: 50 Hz, vrsta laserja: vlakenski laser, The LAS 22 is a compact tabletop unit with a small working area, making it ideally suited for small parts or, for example, nameplates. Due to its compact design, the machine is very practical and can be used virtually anywhere. The device is very easy to operate and requires no programming knowledge. With the powerful laser software, texts, numbers, 2D codes, QR codes, and logos can be created in just a few clicks, without extensive programming skills. The software automatically increments serial and item numbers after initial setup. In addition, the software can retrieve data (such as variable information like drawing numbers, project names, etc.) from existing tables and automatically transfer it to predefined fields. The use of a handheld scanner is also possible. A laptop with a Windows operating system and laser software comes as standard. Optionally, the LAS 22 laser model can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. - 30-watt fiber laser (optional: 20 watts, 50 watts) - Laser class 1 - Wavelength 1064 nm - Marking field size 110 x 110 mm - Marking software EZCAD in German/English - Pilot laser (easy preview/contour preview) - Focus finder (easy focusing) - Max. component height approx. 95 mm - Grid bores for fixtures - Clamping area 310 x 190 mm - Electrically adjustable Z-axis - Electric door with pinch protection - Optional: Fume extraction (incl. activated carbon filter) - Welded construction made of sheet steel - 230 V connection Lrsdpfey I Nbmox Amlsn - Air-cooled - Laptop with Windows operating system (German or English) - Dimensions (W x D x H): 600 x 400 x 690 mm - Weight: approx. 45 kg - Low operating costs

Stanje: novo, Leto izdelave: 2026, * Production time approx. 4-5 months --- Our bestselling briquetting press series + Proven, simple technology for extremely low susceptibility to faults + 25 years of experience, continual development, and expertise + Several hundred machines in operation with satisfied customers + Excellent price-performance ratio The hydraulic briquetting presses of the MPP NEM series compress materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. The machines feature a robust construction that ensures consistent briquette quality during continuous operation. The pressing process is performed without the addition of binding agents, using only hydraulic pressing force. Depending on the material, the volume of the input material can be reduced by up to 90%. The standard silo has a capacity of approx. 0.5 m³. Silos with larger capacities or special containers designed for integration under existing extraction and filtration systems for complete disposal units are also available. Depending on customer requirements, individual MPP NEM units can be combined into a system. The press’s chip hopper can be loaded manually, via conveyor belt, with a dust extractor, or by a tipping container cart. For fully automated system operation, the use of a lift-and-tip device in combination with a shredder is recommended. The briquetting presses of the MPP NEM series are designed for the production of briquettes from homogeneous material. The length of a briquette is, depending on the model, 40 to 75 mm; the diameter is, depending on the type, 50, 65, or 70 mm. For emulsion recovery, the briquetting press can be equipped with a collection tray, allowing cooling, cutting, and lubricating fluids to be collected and recovered. Non-ferrous metal chips up to approx. 20 mm in length are filled into the storage hopper of the briquetting press. A stirrer is installed at the bottom of the hopper to prevent bridging and to feed the material into the pre-compaction chamber. In this chamber, a hydraulic slide pre-compacts the material and pushes it into the pressing block. The main press cylinder presses the material against a vertical slide until the set pressing pressure is reached. The vertical cylinder then moves upward, ejecting the stable briquette. Advantages of briquette production include: • Volume reduction of up to 90% • Emulsion recovery • Cost savings in storage and transport • Cost-effective disposal • Profitable sale Lrjdpfx Amochqxxoljn -- Briquetting Press NEM 300 Throughput approx. up to 200 kg per hour (highly depending on material). - In the last test with aluminum granulate under 5 mm: approx. 186 kg per hour + recovered emulsion. - In the last test with aluminum chips under 18 mm: approx. 120 kg per hour + recovered emulsion. Technical specifications: Motor: 7.5 kW (+ 0.55 kW on the cooler) 400 Volt / 50 Hz / 3-phase Front bushing: 125 mm Max. briquette stroke: 100 mm Optimal briquette stroke: 80 mm Pump: 80 liters Storage hopper approx. 0.5 m³ capacity (extendable)

Stanje: kot nova (razstavni stroj), Leto izdelave: 2024, Special price: €29,970 net One machine is currently available for immediate delivery. The ideal solution for shredding bulky, lightweight aluminum chips or turnings. Not suitable for larger, solid aluminum parts. Included features: + Optimized cutter geometry + Customized pusher control + Load-dependent hydraulically controlled pusher (presses the chips against the cutting unit) Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Knives: 40x40 mm, multiple rotatable Rotor diameter: 260 mm Control: Omron PLC Cutting unit opening: 600 x 800 mm Hopper volume: approx. 0.6 m³ Hydraulically operated pusher Screen perforation as desired (15 - 40 mm) Extraction port Ø 160 mm Weight: approx. 1,300 kg Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm The following options are available at an extra charge: - Raise shredder by 30 cm (preparation for conveyor belt): +€2,990 net - Angled conveyor belt (discharge height approx. 220 cm): +€9,770 net - Overband magnet: +€6,980 net Lrsdpfxegmh H To Amlon - Conveyor belt and overband magnet control: +€2,750 net (Start and stop synchronized with the shredder) We are happy to offer a free test using your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send your material to us via a freight forwarder, and we will document the test with photos and videos.

Stanje: novo, Leto izdelave: 2026, Availability upon request Lrjdpfx Ajd Nm Sijmlon Very robust machine with high pressing force - also suitable for producing marketable briquette quality *depending on material. This is made possible by the large-dimensioned press cylinder and the 70 mm briquette size. Our best-selling briquetting press series + Proven, simple technology, ensuring extremely low susceptibility to failure + 25 years of experience, continuous development, and know-how + Several thousand machines in operation with satisfied customers + Excellent value for money Optional demonstration cooling unit surcharge: + €4,980 net (can also be retrofitted later) * Cools the press clamp (important from 4 hours of operation) and the hydraulic oil * Cooling unit recommended for regular operation exceeding 4 hours continuously Commodity code: 84793010 Briquette diameter: 70 mm Front sleeve: 125 mm Max. briquetting stroke: 100 mm Optimal briquetting stroke: 80 mm Capacity (material-dependent): up to 150 kg/h* *depending on bulk density *based on a bulk density of 200 kg per cubic meter Motor output: 9.2 kW 400 Volt / 50 Hz / 3-phase Length: 2,095 mm Width: 1,300 mm *with large chamber 1,600 mm Height: 1,700 mm Weight: 1,250 kg Oil volume: 220 liters Silo diameter: 1,200 mm Silo capacity: approx. 1 m³ Pump: 75 liters Hydraulic pre-compressor Press clamp cooling option: yes, with optional coolable press clamp Hydraulic oil cooling option: yes Cooling of press clamp and hydraulic oil possible with optional cooling unit Level monitoring option: yes Continuous strand briquette option: yes (material-dependent) Enlarged filling slider option: yes, with optional enlarged filling slider CE compliant Raw material requirements: - Moisture content (atro) must be between at least 6% and a maximum of 18% - Maximum chip length: 20 mm - Installation temperature: heated room with at least +5°C - Material feed must be free from metals and mineral contaminants such as sand, stones, etc. Damage to the pressing tools and/or increased wear may otherwise occur