Linija za formatiranje desk

Weinig, Haist h22al

Stanje: dober (rabljeno), Morsoe mitre guillotine, machine number 48706, in good condition, immediately available. If you are interested, we will be happy to provide you with information about other machines at our facility. You are warmly welcome to inspect the machine at our premises by prior appointment. Hfedsh Aka Ijpfx Af Tob

Leto izdelave: 2011, Stanje: zelo dobro (rabljeno), This is a complete plant for house construction. The prices are listed for each item. Consisting of the following individual components (see attached document): Pictures will follow and are already included in the attached document. Table 1 (Insertion and clamping of the frame work) €34,500 - Height-adjustable longitudinal transport with 3 hinge conveyors and paneling - Pneumatic transverse clamping - Connections for compressed air and electricity Table 2 (Laying and securing the first sheathing) €25,300 - Longitudinal transport with 3 hinge conveyors and paneling - Pneumatic transverse clamping - Connections for compressed air and electricity Intermediate Transport, 3 m long €4,600 (Parking station for multifunction bridge) - Longitudinal transport with 3 hinge conveyors Table 3 (Laying and securing the second sheathing, turning of the element onto the next table) €35,650 - Longitudinal transport with 3 hinge conveyors and paneling - Pneumatic transverse clamping - Connections for compressed air and electricity - Hydraulic turning device Table 4 (Installation of electrical and insulation) €34,500 - Cross transport with rollers and paneling - Cross travel of the table - Connections for compressed air and electricity - Hydraulic turning device Table 5 (Laying the first sheathing and securing the second side) €32,775 - Longitudinal transport with 3 hinge conveyors - Cross transport with rollers - Pneumatic transverse clamping - Connections for compressed air and electricity Intermediate Transport, 3 m long €4,600 (Parking station for multifunction bridge) - Longitudinal transport with 3 hinge conveyors Table 6 (Laying and securing the second sheathing) €28,750 - Longitudinal transport with 3 hinge conveyors - Pneumatic transverse clamping - Connections for compressed air and electricity Table 7 (Erection and distribution table) €29,900 - Longitudinal transport with 3 hinge conveyors - Hydraulic swinging unit - Table cross-travel unit - Upper guide for holding the walls vertically Manual area gantry with vacuum lifter on Table 2 €13,800 (Laying the first sheathing) - Load capacity 85 kg with Schmalz vacuum unit - Steel base frame with lightweight rails - Travel path 12 x 5 m Manual area gantry with vacuum lifter on Table 3 €13,800 (Laying the second sheathing) Hodsu D Amgopfx Af Tofb - Load capacity 85 kg with Schmalz vacuum unit - Steel base frame with lightweight rails - Travel path 12 x 5 m Manual area gantry with vacuum lifter on Table 5 €13,800 (Laying the first sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel base frame with lightweight rails - Travel path 12 x 5 m Manual area gantry with vacuum lifter on Table 6 €13,800 (Laying the second sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel base frame with lightweight rails - Travel path 12 x 5 m Wall rack 1: 12 m long x 24 bays €11,500 Wall rack 2: 12 m long x 20 bays Vacuum lifter with column slewing crane €9,200 1 Spreader beam 2 t Abus €20,125 1 Spreader beam 2 t

Stanje: pripravljen za uporabo (rabljen), De-stacking by layers for layer singulation Stack slat separator with conveyor belt Layer transport to layer buffer Layer buffer with singulation before the feeding unit Hfsdpouzht Tjfx Af Tsb Layer patterns for the two separated timbers including transfer conveyors, for example to the stacking machine

Stanje: zelo dobro (rabljeno), Stehle S820 (avtomatski brusilnik za ravne rezila). Prosimo, preverite tudi v vsiljeni pošti (junk mail), če v roku 24 ur po oddanem povpraševanju ne prejmete odgovora!!! Specifikacije: • Največja širina orodja: 330 mm • Premer orodja – glave za skobljanje (min-max noževne glave): 120 - 230 mm • Hitrost brusilnega kamna: 2850 / 5750 obratov/min Hfsdpsq Dzkusfx Af Tjb • Možno brušenje od 2 do 12 nožev na glavo z indeksnim kolescem • Priložene indeksne plošče za brušenje 4, 6, 8, 10 in 12 nožev • Pogon brusilnega kamna: 1,3 kW • Kot odmika: 10 - 35° • Rezervoar za hladilno tekočino: 125 L • Motor črpalke za hladilno tekočino: 0,28 kW • Priključna moč, skupno: 2 kW Prosimo, preverite tudi v vsiljeni pošti (junk mail), če v roku 24 ur po oddanem povpraševanju ne prejmete odgovora!!!

Stanje: novo, Leto izdelave: 2025, CHIPPING MACHINE, brand KÄLIN Hobeltechnik, model MPC-P: • Approximate wet chip production: 3,800 kg/hour • Log carriage dimensions: 2,800mm x 1,100mm x 1,300mm • Maximum log length: 2,650mm • 2 symmetric, removable cutter heads, diameter 1,140mm each, divided into 3 segments of: - Diameter: 200mm - Length: 380mm - Number of knives: 8 per segment - Complete cutter head sharpening possible without removing knives ULTRA-FAST CUTTER HEAD EXCHANGE, less than 15 minutes! • 2 additional spare cutter sets for exchange during sharpening process • Cutter head motor power: 90kW / 120 HP • Carriage speed controlled by ELECTRONIC INVERTER: 6 to 36 m/min Hedpfx Asvk Saxsf Tsfb • Automatic control of feed-load ratio • 1 feed motor, double heavy-duty chain drive: 15kW / 20 HP • Material level monitoring system within carriage to avoid idle running • Electrical cabinet and control panel. Touchscreen function control • Motorized bottom conveyor for chip extraction: 5,000mm x 800mm • Weight: 11,000 kg • CE CERTIFIED

Stanje: rabljeno, No. 3213 Thermal Treatment Plant / Vacuum Dryer WTT Used, Year of Manufacture 2017 Thermal Treatment Plant / Thermal Chamber for Wood Modification The WTT thermal chamber is a plant for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on wood thickness and type. The plant features a powerful energy and heat transfer system and operates with a gas- or oil-fired boiler using thermal oil as the heat transfer medium. Technical Data: Capacity: 5,950 - 9,900 m³ of wood per year (based on 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions (LxWxH): 10,500 x 1,300 x 1,100 mm Minimum board thickness: 10 mm Power supply: 3 x 400 V, 50 Hz + neutral + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heating output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel Duplex EN 4462 Door opens hydraulically, 1.5 kW drive Operating pressure: 0.1 to 15 bar (absolute) Operating temperature: 0 °C to 220 °C 200 mm glass wool insulation, covered with 1 mm galvanized steel sheet Main Components: 1. Autoclave for heat treatment 2. Vacuum system for extracting air from the autoclave before heating 3. Energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. Nitrogen generator 6. Gas cooling system Heating and Cooling System: Heat exchangers: 8 units (4 each side) Material: Stainless steel tubes (seawater resistant) Total surface area: 165 m² Cooling water consumption: 1,000 l/batch (not contaminated, only heated) Control and Operation: Control system: WTT ExoT (fully automatic) Displays: 22" color monitor with IBM computer and printer Sensors: 4 PT100 temperature sensors Hfsdpsv Si Szsfx Af Tjb 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special Equipment: Hydraulic rail bridge for easy transport of wood trolleys Automatic trolley extraction with winch (1.5 kW) 2 MW thermal oil boiler (heating) Heating oil tank (4,000 l) with measuring system Insulated 20-foot steel container for heating module Safety chimney made of stainless steel (300 mm diameter, 6,000 mm length) Function Description: 1. Loading the autoclave with wood 2. Generating preliminary vacuum 3. Filling with gas 4. Heating 5. Modification 6. Cooling 7. Pressure equalization 8. Generating final vacuum / drying 9. Pressure equalization 10. Unloading Certified according to EC Pressure Equipment Directive (PED) 97/23/EC Design according to EN 13445 Sale on behalf of customer, ex location near 5020 Salzburg (Austria), without disassembly, without transport or installation Disassembly, loading, and transport by us are possible as an option Errors in description and pricing reserved To avoid misunderstandings, on-site inspection by appointment is possible and recommended Sale takes place as is Technical data, description of condition, year of manufacture and scope of supply according to manufacturer's brochure and/or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded; the following applies: "purchased as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Payment terms: Prices plus statutory VAT, payment prior to collection or shipping Delivery terms: ex location

Stanje: rabljeno, No. 3176 WEINIG Hydromat 1000 Planing and Moulding Machine Used, year of manufacture 2007 6 Spindles: bottom-right-left-top-top-bottom Electronic feed: 6 - 60 m/min Working width: 80 - 150 mm Working height: 23 - 65 mm Finished lamella width: 4 - 15 mm Max. number of lamellae: 16 pcs Lamella lengths: 400 - 4000 mm 1st spindle horizontal bottom: Hsdpfeu Agh Sex Af Tjfb Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool circle 125 - 180 mm 2nd spindle vertical right: Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm 3rd spindle vertical left: 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm Pressure shoe in front of spindle, swiveling, pneumatic roller pressure 4th spindle horizontal top: 15 kW, 6000 rpm, diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 5th spindle horizontal top as saw spindle: Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment reduced to 25 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 6th spindle horizontal bottom as saw spindle: Brake motor 30 kW, 5000 rpm Axial adjustment reduced to 25 mm Diameter 45 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm All profiling spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of feed rollers opposite left spindle, axial 35 mm Shortened roller distance opposite right spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in table, lateral pressure roller Automatic Waxilit/lubricant pump Machine with 4-roller outfeed, oscillating shafts extended to 200 mm 2 driven, toothed rollers in outfeed table 2 driven, toothed rollers in machine table Pressure beam ahead of and discharge after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electric height adjustment of upper spindles and feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transport and installation Subject to errors in description and price Transport and loading by us available as an option To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended The sale is made in "as is" condition Technical data, description of condition, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: "sold as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Terms of payment: prices plus statutory VAT, payment before collection or dispatch Delivery terms: ex site

Stanje: rabljeno, Станок для скругления WemaProbst RHM 200 Hjdpsv Ii Tkefx Af Tsfb

Stanje: rabljeno, številka stroja/vozila: IDC000031, Барабан для сушки щепы Длина — 14 м Hfedpfxjrl Ra Hs Af Tjb Ширина — 3,6 м Производительность сушки — 10 т/ч

Leto izdelave: 2000, Stanje: rabljeno, Brucks 100 HP Chipper Hjdpfx Afolxqile Tofb Infeed and discharge conveyor, hopper, screen The machine is sold as is.