Stroj za ostrenje

WEINIG Rondamat 909

Stanje: novo, Leto izdelave: 2025, Nova brusilna stroj za nože z vrtljivim magnetnim mizo, 1200 mm, hitrost sani brezstopenjsko nastavljiva, avtomatski pomik brusilnega koluta, PLC krmiljenje, barvni zaslonski zaslon na dotik, hladilni sistem. Nsdpfx Ajwamkvearjlc

Stanje: zelo dobro (rabljeno), Leto izdelave: 2021, obratovalne ure: 9.500 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 3284, Standardna različica RUF Lignum R2 z izstopnimi kanali, el. motor 22 kW, velikost briket 150x60 mm, zmogljivost do 500 kg/h Nedpfx Aaeyyl Srorjlc

Stanje: zelo dobro (rabljeno), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG transverse conveyor HighMech E-1, with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG accelerator model 814 Short infeed table with heavy-duty 4-roller feed Planing moulder with reinforced KASCHWIG three-sided soundproof cabin • Maximum working width: 230 mm • Maximum working height: 160 mm • Electronic feed, frequency-controlled, 8 – 80 m/min • Feed motor: 18.5 kW • 1st spindle bottom: 11.0 kW • 2nd spindle right: 11.0 kW • 3rd spindle left: 11.0 kW • 4th spindle right: 11.0 kW • 5th spindle left: 11.0 kW • 6th spindle top: 15.0 kW • 7th spindle bottom: 11.0 kW • 8th spindle top: 15.0 kW • 9th spindle bottom: 15.0 kW • 10th spindle universal: 11.0 kW (4-sided) • Spindle speed: 6,000 rpm • Spindle diameter: ø 50 mm • All spindle motors equipped with NEW motor start/stop combination • Pneumatically assisted top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced feed roller spacing • Hard-chromed table plates • Hard-chromed fences • Pneumatically assisted lateral pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Total connected load approx. 145 kW / approx. 400 A • Free-standing switch cabinet • Operating manual, spare parts list, and circuit diagram included • Machine without planing heads Machine dimensions approx.: Njdpfx Aajwvqklerelc • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 KG Factory-new WEINIG parts used: NEW horizontal / vertical spindle NEW counter bearings All spindles with HL bearings All motors newly mounted NEW electronic motor soft start / braking units NEW hard-chromed table plates NEW hard-chromed fences Many other NEW PARTS installed in the machine Condition: see attached photos – technically in top condition Infeed mechanization unrefurbished – all parts present – operational Payment: Prior to loading, net cash Delivery time: By arrangement Delivery: EXW Inspection: Anytime by appointment Subject to prior sale and errors excepted.

Stanje: rabljeno, No. 3176 WEINIG Hydromat 1000 Planing and Moulding Machine Used, year of manufacture 2007 6 Spindles: bottom-right-left-top-top-bottom Electronic feed: 6 - 60 m/min Working width: 80 - 150 mm Working height: 23 - 65 mm Finished lamella width: 4 - 15 mm Max. number of lamellae: 16 pcs Lamella lengths: 400 - 4000 mm 1st spindle horizontal bottom: Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool circle 125 - 180 mm 2nd spindle vertical right: Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm 3rd spindle vertical left: 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm Pressure shoe in front of spindle, swiveling, pneumatic roller pressure 4th spindle horizontal top: 15 kW, 6000 rpm, diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 5th spindle horizontal top as saw spindle: Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment reduced to 25 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 6th spindle horizontal bottom as saw spindle: Brake motor 30 kW, 5000 rpm Axial adjustment reduced to 25 mm Diameter 45 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm All profiling spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of feed rollers opposite left spindle, axial 35 mm Shortened roller distance opposite right spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in table, lateral pressure roller Automatic Waxilit/lubricant pump Machine with 4-roller outfeed, oscillating shafts extended to 200 mm 2 driven, toothed rollers in outfeed table 2 driven, toothed rollers in machine table Pressure beam ahead of and discharge after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electric height adjustment of upper spindles and feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transport and installation Subject to errors in description and price Transport and loading by us available as an option To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended The sale is made in "as is" condition Technical data, description of condition, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: "sold as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Terms of payment: prices plus statutory VAT, payment before collection or dispatch Nedpfxju Agh So Aarolc Delivery terms: ex site

Stanje: rabljeno, No. 3213 Thermal Treatment Plant / Vacuum Dryer WTT Used, Year of Manufacture 2017 Thermal Treatment Plant / Thermal Chamber for Wood Modification The WTT thermal chamber is a plant for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on wood thickness and type. The plant features a powerful energy and heat transfer system and operates with a gas- or oil-fired boiler using thermal oil as the heat transfer medium. Technical Data: Capacity: 5,950 - 9,900 m³ of wood per year (based on 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions (LxWxH): 10,500 x 1,300 x 1,100 mm Minimum board thickness: 10 mm Power supply: 3 x 400 V, 50 Hz + neutral + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heating output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel Duplex EN 4462 Door opens hydraulically, 1.5 kW drive Operating pressure: 0.1 to 15 bar (absolute) Operating temperature: 0 °C to 220 °C 200 mm glass wool insulation, covered with 1 mm galvanized steel sheet Main Components: 1. Autoclave for heat treatment 2. Vacuum system for extracting air from the autoclave before heating 3. Energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. Nitrogen generator 6. Gas cooling system Heating and Cooling System: Heat exchangers: 8 units (4 each side) Material: Stainless steel tubes (seawater resistant) Total surface area: 165 m² Cooling water consumption: 1,000 l/batch (not contaminated, only heated) Control and Operation: Control system: WTT ExoT (fully automatic) Displays: 22" color monitor with IBM computer and printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special Equipment: Hydraulic rail bridge for easy transport of wood trolleys Automatic trolley extraction with winch (1.5 kW) 2 MW thermal oil boiler (heating) Heating oil tank (4,000 l) with measuring system Insulated 20-foot steel container for heating module Safety chimney made of stainless steel (300 mm diameter, 6,000 mm length) Function Description: 1. Loading the autoclave with wood 2. Generating preliminary vacuum 3. Filling with gas 4. Heating 5. Modification 6. Cooling 7. Pressure equalization 8. Generating final vacuum / drying 9. Pressure equalization 10. Unloading Certified according to EC Pressure Equipment Directive (PED) 97/23/EC Design according to EN 13445 Sale on behalf of customer, ex location near 5020 Salzburg (Austria), without disassembly, without transport or installation Disassembly, loading, and transport by us are possible as an option Errors in description and pricing reserved To avoid misunderstandings, on-site inspection by appointment is possible and recommended Sale takes place as is Technical data, description of condition, year of manufacture and scope of supply according to manufacturer's brochure and/or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded; the following applies: "purchased as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Nodpfev Si Szex Aarjlc Payment terms: Prices plus statutory VAT, payment prior to collection or shipping Delivery terms: ex location

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, Viesmann Vitoplex 100 LS with Weishaupt WM - G10/4A Nodotrl Skjpfx Aarelc

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2024, Double-sided cantilever racking used: Hot-dip galvanized bolt system Scope of delivery: - 4 double-sided racking uprights, height 4,160 mm with base 1,200 mm - 24 cantilever arms, 1,200 mm depth, standard - Including longitudinal and diagonal bracing for 1,300 mm axis distance - Incl. mounting material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts reorder and extension possible at any time) - (*Also available in larger quantities: 20 uprights in stock) Detailed description: - Sturdy steel construction made of IPE profiles - All components hot-dip galvanized - Load capacity per upright side: 2,250 kg - Load capacity per cantilever arm: 750 kg - Height-adjustable cantilever arms in 100 mm increments - 6 bolt-on cantilever arms and 2 base parts per upright, standard depth 1,200 mm = 4 storage levels per upright side - Including longitudinal and diagonal bracing for 1,300 mm uprights distance - Rack length 4,000 mm - Including mounting material (without floor anchors) - Supplied with installation instructions and load capacity plates C4 according to DIN standard - Expert telephone consultation - Made in Germany - Short delivery times - On-site pickup possible Our cantilever racks are exclusively manufactured in Germany. Nlodpfxeh Ek Dao Aaroc We offer reliable freight with advance delivery notification. The material is sensibly packed to allow for easy unloading. For outdoor installation, load capacities are reduced due to wind and snow load. The subsoil must be concrete, level and suitable for anchor fixing and must be able to absorb the acting loads. The floor structure and load-bearing capacity as well as any necessary official permits must be checked and ensured by the customer. The racking uprights must be anchored to the floor on site; wall anchoring is neither necessary nor recommended. According to the professional association, it is recommended that the uprights have at least 500 mm overhang on the top storage level above the upright top end.

Stanje: rabljeno, Leto izdelave: 1996, Vollmer CHC 260, leto izdelave 1996 Nledpfx Aaoyuc Ifersc

Stanje: novo, Leto izdelave: 2024, Funkcionalnost: popolnoma funkcionalen, moč: 5 kW (6,80 KM), največja višina reza: 200 mm, največja širina rezanja: 1.300 mm, premer žaginega lista: 550 mm, dolžina rezanja (maks.): 3.200 mm, širina reza pri vzporednem vodilu: 1.300 mm, dolžina pomične mize: 3.200 mm, Exhibition machine F 45 Elmo Drive - Tilting capability + / - 45° - Cutting height 200 mm - Scoring unit preparation No. M24038 - Double roller carriage with 3200 mm travel - Mitre cross-cut fence 3200 mm Digit L - CNC rip fence 1300 mm - Duplex mitre fence 1350 mm manual - Workpiece holder Njdpeuh R R Eefx Aarslc - On/off switch on the double roller carriage - Front support roller

Stanje: rabljeno, Leto izdelave: 2006, skupna širina: 4.600 mm, skupna višina: 1.830 mm, Dimensions (L x W x H): 217 x 460 x 183 cm Price: On request - Year of manufacture: 2006 - Documentation available: No - CE marking present: Yes - CE certificate available: No - Serial number: 107402 - Number of spindles [pcs]: 4 - Spindle 1: - Spindle diameter [mm]: 40 - Spindle 2: - Spindle diameter [mm]: 40 - Spindle 3: - Spindle diameter [mm]: 40 - Spindle 4: - Spindle diameter [mm]: 40 - Infeed table length [mm]: 1780 - Feed motor [kW]: 5.2 - Feed drive: Cardan drive - Extraction nozzle diameter [mm]: 140 - Voltage [V]: 400 Nlsdpfx Aownig Noarsc - Shipping dimensions: 2170mm x 4600mm x 1830mm (l x w x h) - Shipping units [pcs]: 1 Financial information VAT: The stated price is net, plus VAT VAT/margin scheme: VAT deductible for businesses Delivery and trade-in possible at any time for all types of industrial equipment Yorick Diebels