Motor za rezkanje za stroje za obdelavo robov

Perske VS 31.09-4

Stanje: zelo dobro (rabljeno), DOUBLE-SIDED LOADING STATION Vacuum system (with pump) No. 2 vertical support columns for the upper support beam No. 1 upper horizontal support beam (on which the carriage slides) No. 1 motorized carriage with horizontal metal arms External roller conveyor (on the floor) for loading the stack of panels onto the loading station External motorized roller conveyor (for receiving panels from the loading station) Separate electrical control panel Perimeter safety fencing with safety mats Working capacity (cycles/min) approx. 16 Panel thickness (min/max) mm 10 / 50 (approx.) Min. panel dimensions mm 250 x 320 (approx.) Max. panel dimensions mm 1300 x 3000 (approx.) Ledsfi Tg Hspfx Ac Usaf Total connected load kW 30

Stanje: rabljeno, Leto izdelave: 2009, Numerical Control POWER CONTROL PC 22 Machine suitable for the first and second panel pass Mobile motorized shoulder opening via NC, 3000 mm Maximum panel height: 60 mm PVC-ABS edge thickness: 3 mm Feed speed: 40 m/min Feed speed with corner rounding: 20 m/min Motorized rubber pressure belt Support rail with retractable pin (distance between pins: 500 mm) Lajdpfxspp Tkfj Ac Usf Squaring section consisting of: Non-stick unit Time-controlled automatic chip guard unit Double trimming unit Space reserved for future group extensions Gluing unit with pre-melter and glue pot Automatic adjustment of pressure rollers for edging Edge holder magazine with 2 positions Trimming unit with two motors Overlapping cut-off unit Corner rounding group (FK) Scraper unit for edges Glue scraper unit Buffing unit Non-stick unit

Leto izdelave: 2006, stanje: pripravljen za uporabo (rabljen), An on-site inspection is possible. Lasdpfsqvnmbox Ac Uof

Stanje: zelo dobro (rabljeno), DOUBLE-SIDED EDGE-BANDING AND FORMATTING MACHINES – First (1st) machine in line Laedpfxsfi Tkgs Ac Usf Edge thickness from coil (min/max) mm Edge thickness in strips (min/max) mm Panel thickness (min/max) mm 12 - 60 Working width (min/max) mm 1300 Control/software ICOS open Feed speed (adjustable) m/min 9 - 45 No transfer bar (master & slave systems) Pressure belt driven by V-belt FORMATTING UNIT (for each side): Jointing/milling unit 75.30 (kW 6.6 x 1) EDGE-BANDING SECTION (for each side): Gluing unit (P.U.R. glue + pre-melter) 04.1569 + 283.205 Pressure rollers (turret) for straight and softforming edges mm 1,050 Edge magazine for coils (number of slots) 6 End trimming unit 08.42 (kW 0.2 x 2) 40 m/min Pre-milling unit 08.055 (kW 0.66 x 2) 0°-30° Milling unit 08.0582 (kW 0.66 x 2) 0°-30° Scraper unit 08.50 Buffing unit 08.617-2 (kW 0.18 x 2)

Stanje: zelo dobro (rabljeno), Double-sided single machine (or 1st and/or 2nd machine in a production line) Roll material (edge) thickness (min/max) mm: 0.6 - 3 Panel thickness (min/max) mm: 8 - 60 / Working width (min/max) mm: 225 - 3000 Control/Software: Power Control PC 22 - Wood Commander Feed speed (adjustable) m/min: 15 - 32 Cam distance (mm): 400 EDGING PROCESSING (per side): Protection milling cutter (pre-milling) 1 x kW 4.5 Roughing unit KD 11 (2 x kW 6.6) EDGE BANDING SECTION (per side): Gluing unit (Hot melt glue + pre-melter) A3 + SERVO Edge pressure zone “A” Edge magazine for rolls (compartment No. 2) End trimming unit HL 84 (2 x kW 0.22) Pre-milling unit (2 x kW 0.55) Milling unit 2 x kW 0.4 Profile copying milling unit FF 12 (4 motors x kW 0.4) LEFT SIDE: 2 x Universal milling units (electro-pneumatically controlled) UF 11 (kW 4 x 2) 0°-90° Lsdep N D Ngepfx Ac Usaf RIGHT SIDE: 1 x Universal milling unit (electro-pneumatically controlled) UF 11 (kW 4 x 1) 0°-90° Multi-profile scraper unit PN10 (PNEU) Finishing unit (flat scraper + smoothing unit) FA 11

Stanje: potreben popravila (rabljeno), Leto izdelave: 2002, Funkcionalnost: nefunkcionalno, ★ CENA ZNIŽANA – HITRA PRODAJA: 50.000 € (namesto 80.000 €) ★ Prodajamo 3 sušilnice za les Imea 2002 (Imea) + generator pare + kotel (Elbi) 3 sušilnice za les in 1 generator pare: Ljdpfx Acopugxno Ueaf Dimenzije: 12,5 m x 7,2 m x 4,2 m 📐 Kapaciteta za vsako sušilnico: 220 m3 lesa 🌳 Generator pare: 8,5 m x 6 m x 5 m 📐 Aluminijasta konstrukcija, sendvič plošče 🏗️ Kotel za les in žagovino: Opremljen s črpalko, cevovodi in kotlom Moč: 3.500.000 kCal/h (40.000 kW) Vse deluje na avtomatiziranem sistemu. Skupaj: 50.000 € plus DDV 💰 Razstavitev opravi kupec 🔧 Prodajalec lahko pomaga tako, da zagotovi teleskopski viličar. 📍 Naslov za prevzem: Teiu 337291, Romunija 🌍 Za dodatne informacije ali ponudbo nas kontaktirajte.

Stanje: rabljeno, Dimter Profipress L 2500 Leto izdelave: 2006 Dimenzije: • Širina lamele (za plošče): 30-150 mm Lsdpeyhggrofx Ac Ueaf • Debelina: 11-60 mm • Vhodna dolžina: 800-2500 mm • Širina plošče: spremenljiva, do maks. 1300 mm • Širina polnjenja na cikel: min. 650 mm / maks. 1300 mm • Integrirana hidravlična enota za moč stiskanja in hidravlične motorje • Elektrika: • Obratovalna napetost: cca 400 V / 50 Hz • Električna priključna moč za 40 kW HF generator: 56 kW

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, working width 250 mm working height 140 mm 8 heads 3 toothed feed rollers on the infeed table head arrangement: bottom/right/left/right/left/top/top/bottom variable feed speed up to 100 m/min spindle diameter 50 mm spindles supported on both sides feed via cardan shafts spindle speed 6000 rpm Laedpfx Acoww H Rwo Uef pneumatic pressure on feed rollers head adjustment in two axes cast iron body

Stanje: rabljeno, Leto izdelave: 1997, No. 3214 Throughfeed Veneer Press Sergiani LAS Plus Used, year of manufacture 1997, already dismantled and stored Automatic press with continuous operation for the production of flush doors, high-quality doors (veneered doors, HPL, CPL) and pre-finished parquet (2 - 3 layers). The press enables consecutive loading of workpieces while the pressure in the other chambers is kept constant. The line requires up to 2 operators. The multi-daylight press enables very high production output. Pressing time is approx. 3 minutes (180 seconds) distributed across 10 press levels, meaning the press opens every 18 seconds, processing a new panel. The press is already dismantled and stored. The system was in operation until dismantling. The previous owner used the machine for producing 3-layer parquet. The bottom layer was inserted manually. The middle layer consists of one piece, was glued on top and bottom, and automatically loaded into the line. The top layer was also automatically loaded. Glue application machine/glue not included in the scope of supply (available as an option). Number of press levels: 10 Pressing force: approx. 5.5 kg/cm² Total force: 200 tonnes Panel size: approx. 2500 x 1300 mm (L x W) Heating: hot water Application: manufacturing of doors, laminated pressings, veneer and engineered wood processing High productivity with a capacity of up to 1200 doors per shift (manufacturer’s specification) Vacuum loading system with dual-track infeed roller conveyor, without gluing Scissor lift table with conveyor belt (belt approx. 2900 x 1000 mm L x W) Vacuum stacking station with outfeed roller conveyor Space requirement for press with loading table: approx. 6500 x 2365 mm (L x W) Lajdev Sthgjpfx Ac Ujf Space requirement for complete production line: approx. 25000 x 5710 mm (L x W) Sale on behalf of a customer, ex location near 5020 Salzburg (Austria), without transport and assembly Loading and transport by us possible on request Subject to errors in description and price To avoid possible misunderstandings, on-site inspection by appointment is possible and recommended Sale as is Technical data, description of condition, year of manufacture, and scope of supply according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, all warranty is excluded, as is: “sold as seen” Photos and videos are sample images and do not represent the actual scope of supply Payment terms: Prices plus statutory VAT, payment before collection or dispatch Delivery terms: ex location

Stanje: dober (rabljeno), Leto izdelave: 2008, Funkcionalnost: popolnoma funkcionalen, HESSEMANN 3-HEAD SANDER: Abrasive belt dimensions: 2,620 x 1,400 mm 1 Longitudinal sanding unit (with contact roller for calibration work (steel)), Diameter: 250 mm Belt speeds: approx. 18 m/s, 22 kW Anti-wear brake unit, automatic length adjustment Dust extraction device controlled according to the workpiece; reverse-running abrasive belt; abrasive grain compensation via computer. Belt speeds: 1.0 - 18 m/s Drive: 15 kW 1 Longitudinal sanding unit Belt speeds: Laedpfx Ajx Rdn Tec Uof 1.0 - 18 m/s Drive: 15 kW Incl. stepless sanding speed adjustment via electronic frequency controller, with double quantity of suction holes for the dust extraction device. Anti-wear brake unit, automatic adjustment for varying abrasive belt edge lengths, dust extraction device controlled depending on the workpiece, switchable, reverse-running abrasive belt. 2 Pressure beams with selective pressure regulation system – CSD® system Continuously adjustable pressure of individual pressure elements, for both single and multiple feed. Distance: 32 mm. Part tolerance compensation up to 2 mm by maintenance-free pressure magnets. Working width as well as start and end of sanding on the pressure beam are electronically controlled. The pressure elements are actuated by electro-lifting magnets, allowing the sanding shoe pressure to be infinitely variable as the workpiece passes through the machine. This innovative CSD® technology ensures always consistently proportional pressure depending on the shoe’s overlap on the workpiece. The risk of edge-through (“burn through”) is almost eliminated thanks to this continuous dynamic pressure control.