Optimizacija nakup rabljenega (90)

Stanje: zelo dobro (rabljeno), Leto izdelave: 1993, Funkcionalnost: popolnoma funkcionalen, premer žaginega lista: 450 mm, največja višina reza: 80 mm, največja širina rezanja: 150 mm, pogonska enota žage: 5.500 W, moč: 5,5 kW (7,48 KM), skupna višina: 2.000 mm, skupna dolžina: 20.000 mm, moč servomotorja: 5.500 W, skupna širina: 2.000 mm, vrsta vhodnega toka: trifazni, premer povezave za izpihovanje: 140 mm, priključek za stisnjen zrak: 3,5 letvica, skupna masa: 2.500 kg, Optimiziran prečni rezalni sistem GreCon tip 1004 z vstopnim prečnim transporterjem z izhodnim transporterjem z 10 izmetači z verigo Tehnične specifikacije: Maks. širina obdelovancev: 250 mm Maks. debelina obdelovancev: 80 mm Premer žaginega lista: 450 mm Hitrost rezanja: 90 m/s Motor žage: 5,5 kW Krmiljenje osi žage: pnevmatsko Fsdpfx Ahewy Np Ue Dopn Pogonska veriga: servomotor Min. delovna širina: 40 mm Min. vhodna dolžina: 500 mm Neto teža: pribl. 2500 kg SICK LUT kamera za zaznavanje krede postaja za zaznavanje in sortiranje kakovosti in dolžine

Stanje: rabljeno, Leto izdelave: 2001, Wood processing dimensions: Infeed lengths min/max: 500 - 6500 mm Full optimization up to max: 1500 mm Infeed widths min/max: 40 - 300 mm Infeed thicknesses min/max: 15 - 120 mm Max. wood cross-sections: 300 x 40 mm or 200 x 120 mm Fixed lengths after saw min: 510 – 2800 mm Special application: Cutting blocks, min/max length: 100 – 200 mm (Note: Multiple block lengths during sorting; blocks are conveyed to the end of the sorting line and fall into customer-supplied mesh boxes) Cutting/trim tolerance: +/- 0.8 – 1.5 mm (depending on timber quality with minimal resin content and uniform surface. Tolerance up to 1 m fixed length; maximum tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm Wood curvature in all directions: max. 10 mm per meter length Wood species: Softwood or hardwood System performance: Feed speed, steplessly adjustable up to max. 230 m/min Cutting cycle: 0.6 – 1 s To determine actual daily output, an efficiency factor dependent on the customer’s production conditions must be applied. Working height infeed and saw: 900 mm (to be placed on customer-side platform; saw requires concrete base) Sorting working height: 2000 mm Connection data: Total electrical connection load: approx. 18 kW Operating voltage: 380 Volt / 50 Hz Voltage fluctuations max. 5 % Air consumption: approx. 1200 NL/min Operating pressure: approx. 8 bar Extraction speed: approx. 30 m/s Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge Pos. 2: Support roller without drive, front-facing sheets table for easier loading Pos. 3: Length measuring station with built-in fluorescence camera to detect error markings Pos. 4: Automatic, contactless width measurement Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with integrated waste chute, incl. equipment package for large wood cross-sections Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and system control Available for processing: - max. 16 product groups Fodpow Sy T Hjfx Ah Dopn - max. 8 grades per product group - max. 200 fixed lengths per product group Pos. 6: Outfeed conveyor belt as sorting station with drive unit, length 7500 mm Pos. 7: 2 ejectors mounted on outfeed conveyor Location: Nattheim

Stanje: rabljeno, Circular saw blade diameter: 500 mm Max. cutting height: 120 mm Motor power: 5.5/7.5 kW Working length: 4100 mm Salvapush 2000 optimizing cross-cut saw For complete wood optimization and defect cutting Version 4100 (working length) ----- Technical specifications: - Cutting range: min. 30x12 mm, max. 270x120 / 300x95 mm. Optional special cutting ranges on request. - Plate length before cutting: min. 500 mm, max. 4100 / 5100 / 6100 mm, depending on version - Possibility of a single cut in the last 40 mm of the board. Minimum final trim length: 5 mm. - Maximum wood weight: 120 kg (optional special solution on request) - Feed with pusher, directly controlled by an innovative Fpsdpfx Aswhf Ipsh Don computer-controlled and servo-driven system, digitally connected via EtherCAT. - Special working table inclined at 25 degrees for easy loading and to hold the workpiece securely clamped - Double steel frame construction, highly robust, reinforced and painted. - Special rear safety locking device for appropriate occupational safety. Pusher speed up to 60 m/min in compliance with current safety regulations: Carriage travel speed can be set directly from the computer depending on cutting area. Faster version optionally available. - Very sturdy pusher carriage: extended dimensions approx. 300x345x25 mm. - The aluminum support is large and solid: height 135 mm, width 120 mm. - Special transmission system with 50 mm wide toothed belt with 33 hardened steel bands inside, ensuring high precision and performance - Electronic brushless servo motor with constant torque and digital EtherCAT connection - Photoelectric laser cell for wood detection, and a luminescence reader for fluorescent markings. System is fixed-position, eliminating manual adjustments when wood thickness changes. - Electronic operating system S-OPTIM - Complete management of up to 5 cutting grades - Robust discharge table for collecting the cut workpieces, made of hard steel, length 3000 mm. Inclined at 25 degrees, same as rest of the conveyor, and complete with guide ----- Price of the machine as listed: on request! ----- Optional extras (at surcharge): - Extended discharge (outfeed) table - Gravity preloading system - Zebra label printer - Saw motor upgrade from 5.5 kW to 7.5 kW - Extension of cutting range to 140x240 – 100x300 with circular saw blade diameter 550 mm - Horizontal side discharge - Wide pusher plate Optional alternatives to discharge (outfeed) table: - Version TT: rotary discharge table for full discharge of all cut parts in one cycle - Floor flap for discharge table with rotary function to remove end pieces from trimmed lumber - Version LS: electronic sorting unit For sorting cut pieces by size and grade with 3 high-speed ejectors ----- Prices for the above options: on request! ----- (Technical data as per manufacturer's specifications – subject to change without notice!)

Stanje: zelo dobro (rabljeno), Leto izdelave: 2018, obratovalne ure: 100.000 h, Funkcionalnost: popolnoma funkcionalen, dolžina podajanja os X: 6.000 mm, premer žaginega lista: 700 mm, največja višina reza: 150 mm, teža obdelovanca (maks.): 250 kg, natančnost pozicioniranja: 2 mm, največja širina rezanja: 520 mm, natančnost merjenja poti: 2 mm, vrsta vhodnega toka: trifazni, priključek za stisnjen zrak: 8 letvica, leto zadnje generalne obnove: 2025, CURSAL TRSI 700 z avtomatskim nalaganjem z vakuumsko priseskom, brez operaterja, kompletna z iztokom in vstavnikom v večlistno žago, plus iztok odpadkov in valjčna proga za večlistno žago (brez večlistne žage) Fpjdpfxexdlt Is Ah Dsn

Stanje: novo, Lacquering and Drying Rack 20/2X Fodjtqdl Espfx Ah Djpn Arm length: 780 mm Distance between arms: 120 mm Min/Max workpiece length: 300 / 2650 mm Number of arms: 19

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, Dimter OPTICUT 204R Nadzor OPTICOM ASSIST – programiranje v jezikih CZ/DE/EN Programiranje – po razredih, kakovosti, rezanju po črti, rezanju na dolžino – popolna optimizacija Zelo enostavno programiranje Popolna dokumentacija – navodila za uporabo, katalog delov, pnevmatične in električne sheme Maksimalna dolžina reza 4000 mm (možnost povečave do 6700 mm) Maksimalna višina reza 100 mm Maksimalna širina reza 260 mm Fodpoxgdwdefx Ah Dopn Premer žaginega lista 500 mm Hitrost podajanja 180 m/min Število sortirnikov – 4 (možnost nadgradnje na 10) Dvignitev žage – pnevmatska Natančnost reza +/- 0,5 mm Stroj je priključen na elektriko in ga je mogoče preizkusiti Stroj je kot nov, 100% kompleten in delujoč! Po dogovoru lahko organiziramo prevoz po EU

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2009, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 4421.24, hitrost pomika os X: 60 m/min, potrebna višina: 1.950 mm, zahteva za prostor dolžina: 16.300 mm, potrebna širina: 2.700 mm, TEHNIČNE PODROBNOSTI Avtomatski pomik: do 60 m/min Fodjw Tzh Uopfx Ah Djpn PODROBNOSTI O STROJU Serijska številka: 4421.24 Leto izdelave: 2009 Trifazni tok: 400 V / 50 Hz Krmilna napetost: 24 VAC / 230 VDC Moč: 20 kW Nazivni tok: 40 A Zavarovanje: 50 A Dimenzije stroja (D׊×V): 2.000 x 1.400 x 1.650 mm Dimenzije vhodne mize (D׊×V): 7.450 x 2.100 x 1.100 mm Dimenzije izhodne mize (D׊×V): 4.900 x 2.400 x 1.400 mm Skupne dimenzije (D׊×V): 16.300 x 2.700 x 1.950 mm OPREMA - Avtomatski pomik

Stanje: dober (rabljeno), Leto izdelave: 1992, I am selling an automatic pneumatic cross-cut saw, GreCon Dimter 2004, year of manufacture 1992. Automatic infeed table / through-feed system Outfeed table 3 ejectors on the left outfeed table Fodpfet Ir Nqex Ah Dopn Total length: 15.50 m Optimization with automatic defect detection and automatic cut pattern programming. Available immediately. Spare parts and documentation included.

Stanje: novo, Leto izdelave: 2024, Professional machine for removing defects from wood and wooden elements. It optimizes the cutting process and ensures minimal material loss. The CROSS CUT 306 optimizer is a new technology in woodworking machinery, manufactured by the leading Polish brand CNC Technologies. The machine enables quick, simple, and precise customized cuts, thereby increasing production efficiency. The optimizer crosscuts the material into sections of a specified length, removes material defects marked with a fluorescent marker, and uses a sensor to analyze the marker's position. It is worth noting that the machine is capable of automatic measuring and cutting cycles. Model: TechnologiesCNC CROSS CUT 306-4M Effective processing length – 4000 mm (optionally 6 m) Effective processing width – 30-230 mm Effective processing thickness – 40-80 mm Effective cross-section processing – 250x30 mm Scanning speed – 80 m/min Scanning device – Infrared sensor from German brand SICK Defect scanning/detection – Fluorescence sensor by SICK (Germany) Table height – 800 mm Feed speed – 60 m/min Push servo drive – AC DELTA 750w Saw stroke servo drive – AC DELTA 1 kW Fsdpstvmv Rofx Ah Dspn Cut-off saw motor – 7.5 kW, 3Ph, 2930 rpm Cut-off saw diameter – e.g., 500 mm Extraction port diameter: 100 mm x2 Total power: approx. 10 kW Overall dimensions – 6750 x 1450 x 1800 mm Transport dimensions: 535 x 80 x 110 (table), 200 x 100 x 160 (console) Weight: 1436 kg

Stanje: rabljeno, DIMENSIONS: HEIGHT 100 mm WIDTH 270 mm Fpsdpfx Aow E Eudoh Dsn ELECTRONIC PUSHER LENGTH 6100 mm SAW BLADE MOTOR 4 kW

Stanje: zelo dobro (rabljeno), Leto izdelave: 2017, Optimizer Salvador SuperCut 500 Year of manufacture: 2017 Technical condition: very good Technical specifications: - Maximum installed power: 11.5 kW Fjdpfxouyfx Rj Ah Depn - Saw motor power: 5.5 kW - Maximum material cross-section: 300x60 mm - Minimum element cross-section: 35x15 mm - Minimum element length: 1000 mm - Cutting time: 0.1 – 1 s - Feed speed: 0 – 150 m/min - Number of ejectors: 10 Installation and operator training available at extra cost.

Stanje: novo, Leto izdelave: 2025, COST CUTTING OPTIMIZING SAW The Superangle 600 is the ideal cutting centre for angle cuts and optimization tasks. As the direct technological evolution of traditional cutting methods, the Superangle 600 increases productivity, ensures maximum precision, and maintains a process logic that is both simple and flexible. EXTREMELY ROBUST Entirely constructed from thick, reinforced painted steel. Pusher carriage dimensions: 300x345x25 mm. 50 mm wide toothed belt with 33 internal steel inserts. TECHNOLOGICALLY ADVANCED Electronic system consists of a computer directly connected to a state-of-the-art CNC controller. Windows-based software environment. Includes management of five qualities. 22" LED colour monitor. Online teleservice via internet, plus Excel macro integration. FAST Total optic system. Electronic movement driven by brushless servo motor. Brushless servo motor for angular cutting operations. Adjustable cutting speed. Two pressure arms. RELIABLE AND SAFE Transmission system on double, hardened and ground linear guides. Fpodswk E Uuopfx Ah Don SKF ball bearing carriages with double dust protection and automatic lubrication. Freestanding, electrically separated control cabinet. Independent pneumatic adjustments for various processing types. Maximum safety rear safety guard.

Stanje: novo, Leto izdelave: 2025, New optimization saw SALVACUT 5000 from SALVAMAC Innovative high-speed optimizing saw with optimization and removal of wood defects, featuring dual drive with upper rollers and a lower feed belt with independent control. Based on an idea by Salvador Christian. Fedpsn E Sl Rofx Ah Djpn

Stanje: novo, Tip specifikacije S120/S260 Radna širina 20–120 mm / 20–260 mm Radna debljina 12–50 mm / 12–80 mm Maks. dimenzija rezanja 80x50 mm / 180x80 mm / 150x100 mm Širina radnog stola 330 mm / 330 mm Min. ulazna dužina 400 mm / 400 mm Brzina dovodnog stola 80 m/min / 80 m/min Broj glavnih dovodnih točkova 5 / 5 List pile 405 mm / 455 mm / 455 mm / 510 mm Brzina vretena pile 3500 o/min / 3500 o/min Snaga motora pile 5,5 kW / 5,5 kW Brzina podizanja pile (gore-dole) 2–4 puta / 1 sek. / 2–4 puta / 1 sek. Snaga motora za podizanje 3 kW / 3 kW Snaga motora dovoda 3 kW / 3 kW Snaga motora pritisnog točka 0,18 kW / 0,18 kW Fedpfxsq Ny Efj Ah Djpn Ukupna snaga 12,43 kW / 12,43 kW Potrošnja vazduha 1000 NL/min / 1000 NL/min Radni pritisak 0,6 MPa / 0,6 MPa Prečnik priključka za izvlačenje prašine Ф140 mm x2 / Ф140 mm x2 Brzina izvlačenja 30 m/s / 30 m/s Težina 1000 / 1000 kg Dimenzije 6500 x 1400 x 1800 mm / 6500 x 1400 x 1800 mm Cena: 31.000 / 32.500 € (EXW Jonava, Litvanija)

Leto izdelave: 2004, Stanje: zelo dobro (rabljeno), Dimter Optimizing Crosscut Saw 350 with increased working height 1400 mm Cross feed as shown in pictures Crosscut saw Control cabinet Scanner interface Fpodpfx Ahjncc Icj Djn Sorting line 6500 mm length with 3 pushers Waste flap Machine has already been dismantled and is immediately available Machine was fully functional until dismantling Transport can be organized

Stanje: zelo dobro (rabljeno), GreCon Type 2004 Optimizing Cross-Cut Saw with infeed cross conveyor with outfeed conveyor belt featuring 4 ejectors with chain bed Technical Specifications: Max. workpiece width: 250 mm Max. workpiece thickness: 80 mm Saw blade diameter: 450 mm Cutting speed: 90 m/sec. Saw motor: 5.5 kW Saw shaft control: pneumatic Chain drive: servo motor Min. working width: 40 mm Min. infeed length: 500 mm Net weight: approx. 1,800 kg Fsdpfxon Hwl Ao Ah Dspn Was completely overhauled and then not used again Location: Austria, near Ried im Innkreis

Stanje: novo, Leto izdelave: 2025, Dimensions (Length/Width/Height): 6400x1500x1780 mm Total Power Requirement: 19 kW Weight: 1800 kg Optimizing Cross-Cut Saw WINTER QUICK 100 NC - Minimum workpiece length: 300 mm Fpedpfx Ahjwt Ua Ej Djn - Workpiece width min. / max.: 20–220 mm - Workpiece thickness min. / max.: 15–100 mm - Workpiece thickness tolerance: ±3 mm - Maximum tolerance range (per side) of the workpiece: 10 mm/m - Wood types: softwood or hardwood - Minimum cutting length: 80 mm - Maximum feed speed: 180 m/min - Cutting speed: 0.15–0.3 s - Total power: 19.0 kW - Saw motor: 7.5 kW - Feed servo motor: 5.5 kW - Saw stroke servo motor: 4.5 kW - Conveyor belt motor: 0.75 kW - Beam lift motor: 0.37 kW - Extraction port diameter: 2 × f120 mm - Table height: 900 mm - Overall dimensions L=6400, W=1500, H=1780 mm - Weight: 1800 kg Standard configurations: - Infeed and marking station with servo drive - Infeed conveyor and saw stroke with individual servo motors - 2.5 m outfeed belt with fluorescence sensor and ejection - Saw blade with integrated waste air-blow device - User-friendly 10.1-inch TFT touchscreen - Air tank for stable pressing force - High-performance servo motor - Fully enclosed safety cover for low-noise and safe operation Efficient production: can replace 4–8 conventional manual cross-cut saws; saves on labor and space, with safer operation. Can be combined with a high-speed four-sided planer to form an efficient, automatic production line.

Stanje: novo, Leto izdelave: 2025, Semi-automatic optimizing crosscut saw with electronic positioner, featuring push/stop operation modes COST-OPTIMIZING CROSSCUT SAW Superpush 150 is the entry-level center for cutting and optimization tasks. Designed as a direct technological evolution of traditional cutting methods, it is capable of increasing productivity and yield of the wood material. EXTREMELY ROBUST Heavy-duty, reinforced welded steel frame, fully painted. Horizontal worktable with movable guard for easier loading of workpieces. Carriage acts as both a length stop and pusher. Linear unit with toothed belt featuring internal steel inserts and linear guideways with ball bearings. Continuous horizontal outfeed table, 300 mm wide. TECHNOLOGICALLY INNOVATIVE Electronic system equipped with an integrated CNC and touch screen control panel. Linux-based software with a customized interface. 15.6'' color resistive TOUCH SCREEN display, ensuring comprehensive safety in industrial environments. Program import via USB. Remote service capability via internet. + Excel Macro support. Fodpfog Hzvgex Ah Djpn FAST S4U Lite software Brushless positioner motor with digital servo-driver. Quick selection interface for Stop/Pusher mode. Adjustable cutting speed. RELIABLE AND SAFE Movements with ball bearing slides, featuring dual dust protection. Electrical cabinet free-standing and separate from the machine structure. Independent pneumatic adjustments to accommodate various processing types. Two-hand safety operation for cutting activation. "CE" certified by accredited body – not self-certified.

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, premer žaginega lista: 500 mm, moč: 10 kW (13,60 KM), The automatic optimizing saw SalvaPush_2000 is the result of more than twenty years of experience with wood optimization saws. The operator needs only to mark wood quality and the presence of defects; the rest is handled by the optimizing saw. The machine cuts the best possible combination of dimensions, minimizes waste, and increases productivity, all while maintaining absolute safety. SalvaPush_2000 is a numerically controlled optimizing saw with integrated computer and SALVA-OPTIM software for fast and easy communication. Certain sections of the program are dedicated to statistics and cutting results, with real-time updates and diagnostics. The touchscreen interface with USB and remote service connection allows for easy data reading and input. Fpodpjd Tyf Uofx Ah Don By Christian Salvador

Stanje: dober (rabljeno), Leto izdelave: 1999, številka stroja/vozila: 89257, GreCon Dimter Opticut 704 L saw from 1999. Fpjdpfx Ahetvahlj Den Machine dismantled from an operational line. Available for inspection at our facility.

Stanje: novo, Leto izdelave: 2025, Dimensions (L/W/H): 0x0x0 mm Weight: 1,500 kg Total power requirement: 10.2 kW Fully optimizing automatic cross-cut saw TR-600 MATRIX-6000 - Motor drive power: 9.2 kW - Saw blade diameter: 600 x 30 mm Z=60 - Cutting capacity according to the cutting diagram - Cutting capacity: 150 x 365 mm - Cutting capacity: 130 x 440 mm - Cutting capacity: 100 x 530 mm - Cutting capacity: 60 x 580 mm - Cutting capacity: 30 x 610 mm - Cutting cycle: 6 seconds - Hydraulic cross-cutting unit - 8° inclined worktable - Minimum workpiece thickness: 10 mm - Safety guard over cutting unit - CE standard Fpodpfxjv A Htkj Ah Den - Weight: 1,500 kg Connection data: - Supply voltage: 400 V / 50 Hz - Control voltage: 24 V - Extraction ports: 4 x 100 mm diameter - Extraction capacity: 2,400 m³/h - Air velocity at extraction nozzle center: approx. 25-35 m/s Electronically controlled pusher: - Infeed length: 6,000 mm - Pusher speed: 90 m/min - Drive via brushless servomotor - Feed system with precision rack and pinion, position feedback via servomotor - Pneumatic lift of pusher at end of cycle with overhead return - Photocell for workpiece length measurement - Photocell for defect detection – marking with fluorescent chalk - Worktable inclination: 8° - Positioning tolerance: +/- 0.4 mm Control system: - High-resolution 12" touchscreen monitor (800 x 600 pixels) - Creation of cutting lists directly in machine control - Up to 1,000 cutting lists with 10 dimensions each - Single list with 10,000 sequential dimensions - 3 optimization options (maximum length, sequence, workpiece sequence) - 3 further optimization options (volume, minimal waste, priority) - Standard USB and Ethernet connection - Includes "OPTI" Function for automatic measurement of the workpiece to be cut. Optimal solution for processing material with varying lengths, with single or batch feeding - 6 optimization options (maximum length, sequence, workpiece sequence, volume, minimal waste, priority) - Includes "OPTI PLUS" Function for detection of markings, ensuring full optimization and removal of knots and defects. - Markings with chalk Options: - Pneumatic side clamp: €850.00 - Cutting list creation via PC: €360.00 - Outfeed table: €360.00/m

Stanje: novo, Leto izdelave: 2025, Dimensions (L/W/H): 0 x 0 x 0 mm Weight: 1000 kg Total power requirement: 8.5 kW Fully optimizing automatic cross-cut saw TR-500 MATRIX-6000 - Motor drive power: 7.5 kW - Saw blade diameter: 500 x 30 mm Z=144 - Cutting capacity according to cutting diagram Fpjdsv A Htdspfx Ah Djn - Cutting capacities: - 135 x 280 mm - 125 x 295 mm - 95 x 325 mm - 80 x 340 mm - 55 x 360 mm - Cutting cycle: 4 seconds - Pneumatic cross-cut unit - 8° inclined work table - Minimum workpiece thickness: 10 mm - Safety cover over cross-cut unit - CE standard - Weight: 1000 kg Connection data: - Supply voltage: 400 V / 50 Hz - Control voltage: 24 V - Extraction ports: 4 x diameter 100 mm - Extraction performance: 2400 m³/h - Air consumption per cycle: 4 Nl - Extraction air speed at port center: approx. 25-35 m/s Electronically controlled pusher: - Feed length: 6000 mm - Pusher speed: 90 m/min - Driven by brushless servo motor - Feed system with precision rack and mass measurement via servo motor - Pneumatic pusher lift at end of cycle and overhead return - Photocell for workpiece length measurement - Photocell for defect reading – marking with fluorescent chalk - Working surface inclination: 8° - Positioning tolerance: +/- 0.4 mm Control system: - High-resolution 12" touchscreen monitor (800 x 600 pixels) - Creation of cutting lists directly on the machine control - Up to 1000 cutting lists with 10 dimensions each - Single list with up to 10,000 dimensions in sequence - 3 optimization options (maximum length, sequence, and workpiece sequence) - 3 optimization options (volume, minimal waste, and priority) - Standard USB and Ethernet ports - Includes "OPTI" Automatic measuring function for the workpiece to be cut. Optimal solution for processing material with variable lengths, with single or pack feeding - 6 optimization options (maximum length, sequence, workpiece sequence, volume, minimal waste, and priority) - Includes "OPTI PLUS" Function for reading markings to ensure full optimization and removal of knots and defects. - Markings with chalk Option: - Pneumatic side clamp €850.00 - Cutting list creation via PC €360.00 - Outfeed table €360.00/m

Stanje: novo, Leto izdelave: 2025, Dimensions (L x W x H) 0 x 0 x 0 mm Weight 900 kg Total power requirement 5 kW Fully optimizing automatic cross-cut saw TR-450 MATRIX-6000 - Motor drive power: 4.0 kW - Saw blade diameter: 450 x 30 mm Z=72 - Cutting capacity according to diagram - Cutting capacity 95 x 265 mm - Cutting capacity 85 x 277 mm - Cutting capacity 60 x 290 mm - Cutting capacity 40 x 310 mm Fsdpfx Asv A Hr Toh Djpn - Cutting capacity 25 x 330 mm - Cutting cycle 4 seconds - Pneumatic cutting unit - Work table inclined by 8° - Minimum workpiece thickness 10 mm - Safety cover over cutting unit - CE standard - Weight 900 kg Connection values: - Supply voltage 400 V / 50 Hz - Control voltage 24 V - Extraction ports 2 x 100 mm diameter - Extraction capacity 2400 m3/h - Air consumption per cycle 6 Nl - Airspeed at extraction port center approx. 25-35 m/s Electronically controlled pusher: - Feed length: 6000 mm - Pusher speed 90 m/min - Drive via brushless servomotor - Feed system with precision rack and pinion and position feedback via servomotor - Pneumatic pusher lifting at cycle end and overhead return - Photocell for workpiece length measurement - Photocell for defect detection – marking with fluorescent chalk - Work table inclination 8° - Positioning tolerance +/- 0.4 mm Control: - High-resolution 12" touchscreen monitor (800 x 600 pixels) - Creation of cutting lists directly on the machine control - Up to 1000 cutting lists with 10 dimensions each - Single list with up to 10,000 dimensions in sequence - 3 optimization options (maximum length, sequence, and item sequence) - 3 optimization options (volume, minimum waste, priority) - Standard USB and Ethernet port - Includes "OPTI" Function for automatic measurement of the workpiece to be cut. Optimal solution for processing material with variable lengths, with single piece or bundle feeding - 6 optimization options (maximum length, sequence, item sequence, volume, minimum waste, priority) - Includes "OPTI PLUS" Function for detection of markings, enabling full optimization and removal of knots and defects. - Marking with chalk Options: - Pneumatic side clamp €850.00 - Creation of cutting lists on PC €360.00 - Outfeed table €360.00/m

Stanje: novo, Leto izdelave: 2025, Dimensions (L x W x H): 4500 x 1200 x 1200 mm Weight: 1,500 kg Total power requirement: 8 kW Optimizing cross-cut saw WS1 - Cutting height Position A: 130x175, 120x200, 100x230, 85x250, 50x280, 15x305 mm Position B: 100x290, 80x315, 50x340, 30x355, 15x365 mm - Cutting speed: up to 100 cycles/min. - Feed speed: 120 m/min. - Motor power: 7.5 kW - Voltage: 400 V / 50 Hz - Saw blade diameter: 500 mm, bore 30 mm - Speed: 3,600 rpm - Min. workpiece length: 550 mm - Min. workpiece width: 40 mm - Min. workpiece height: 15 mm - Cutting accuracy: +/- 0.8 mm - Infeed roller conveyor right: 2,000 mm with double marking station - Outfeed table left: 1,000 mm - Extraction socket diameter: 200 mm - Air consumption: 20 NL/cycle - Operating pressure: 6 bar - Working height: 930 mm - PLC control with 7" color touchscreen for easy operation + Fixed-length cross-cut mode + Sequential cross-cut mode (stores up to 10 different dimensions) Fpsdpfx Ahsvz Hz Ej Don + Cross-cut by marked chalk lines + Cross-cut fixed-length and by marked chalk lines - CE conformity - Dimensions: L = 4,500, W = 1,200, H = 1,200 mm - Weight: 1,500 kg

Stanje: novo, Leto izdelave: 2025, Dimensions (L/W/H): 3000 x 1070 x 1200 mm Weight: 1150 kg Total power requirement: 10 kW Optimizing Crosscut Saw OPTIMAX 100 - Saw motor: 7.5 kW - Speed: 3200 rpm - Feed motor: 2.0 kW - Feed speed steplessly adjustable up to max. 80 m/min - Cutting cycle rate up to 80 strokes/min - Saw blade diameter Ø 455 mm Fpsdjvz Hzxepfx Ah Dsn - Saw blade bore 30 mm - Cutting height 100 mm (according to cutting diagram) - High cutting accuracy ±1 mm - Min. workpiece length 300 mm - Min. distance between markings 20 mm - Min. workpiece size 300 x 30 x 10 mm - PLC control with touchscreen for simple operation + Fixed-length crosscut mode + Sequential crosscut mode (10 different dimensions can be stored) + Crosscutting of marked chalk lines + Fixed-length and marked chalk line crosscutting - Infeed roller table right 1200 mm - Outfeed table left 1000 mm - Compressed air connection 8 bar - CE conformity - Dimensions: L=3000, W=1070, H=1200 mm - Weight: 1150 kg