Gannomat Protec nakup rabljenega (57)

Stanje: novo, Leto izdelave: 2026, GANNOMAT "PROTEC 571" (vrtanje, rezkanje utorjev, rezkanje) Osnovni stroj v standardni izvedbi za vrtanje in rezkanje utorjev vključuje: Dodatni varnostni sistem z lamelnimi zavesami - Pogoj za horizontalno rezkanje Lamello P-System - Pogoj za premer rezkanja > Ø 16 mm ter za uporabo večdelnih rezkalnih orodij Ncsdpfx Alezgfwletew Podrobni tehnični podatki so navedeni v podatkovnem listu za ProTec tip 0571 Obdelovalna enota z: PowerBlock z 21 vreteni in 1 rezalno žago za utore - 13 navpičnih vrtalnih vreten - 6 horizontalnih vrtalnih vreten v osi Y / 2 horizontalni vrtalni vreteni v osi X - 1 enota za rezkanje utorjev v osi Y 4. vrtalna os v Y Velikosti in teže obdelovanca - Širina obdelovanca (X): min. 60 mm / maks. 1000 mm - Debelina obdelovanca (Z): min. 6 mm / maks. 60 mm - Dolžina obdelovanca (Y): min. 250 mm v režimu kontinuiranega podajanja maks. 5600 mm programsko nastavljiva dolžina obdelovanca v programski opremi - Teža obdelovanca: maks. 75 kg 1 Rezkalna enota Profit HSK63F s 3-kratnim magazinom za samodejno menjavo orodja, Motor 5,5 kW (S1), 1000–18000 vrt/min, z frekvenčnim pretvornikom, desni in levi tek, za vpenjalke HSK63F s vpenjalnim tulecem 462E/OZ25, dolžina rezkala do 130 mm vključuje možnosti 1 Preklopna valjčna miza 765 mm (Y-os) za sprednjo stran stroja, širina 500 mm 1 Preklopna valjčna miza 765 mm (Y-os) za zadnjo stran stroja, širina 500 mm 1 Pomožno vodilo 600 mm z integriranimi valji za valjčne mize 1 ORODJA: komplet svedrov za ProTec 1 HW rezkar za utore Ø 125/30 mm, širina utora (SB) 4 mm, Z=12, levo, znamka Leitz 1 Orodja za rezkalno enoto Profit HSK63F in HSK63F s 3-kratnim magazinom s vpenjalnim tulecem 462E do premera stebla 25 mm, komplet HSK in rezkal 1 HSK montažni set 1 Montažna naprava HSK63F, izjemno enostavna uporaba z maksimalnim udobjem zaradi valjčnega napenjalnega sistema, vpenjanje ali stiskanje ni potrebno, nameščeno na stabilno ogrodje ali delovno mizo, 1 Kljúč s kavljem za vpenjalke HSK63F 462E, 1 Razdelilnik za odsesavanje Ø 160 mm / Ø 80-80-80 mm, razmak 196 mm 1 Proti-tlačna enota od zgoraj 1 LED razsvetljava v delovnem prostoru stroja 1 Orodje za vertikalno rezkanje Lamello P-System Stroj je zelo dobro opremljen, vključno s številnimi svedri in orodji. Nov stroj s polno garancijo. Stroj si lahko ogledate in preizkusite v našem razstavnem prostoru. Posebna cena za naš razstavni stroj na voljo po dogovoru!!!!!

Stanje: rabljeno, Leto izdelave: 2023, Nova demonstracijska naprava! Maloprodajna cena: 86.567 € neto. Osnovna naprava, v standardni izvedbi za vrtanje in utore: Podrobne tehnične podatke si oglejte v tehničnem listu za ProTec tip 0571. Obdelovalna enota z: PowerBlock z 21 vreteni in 1 žago za utore - 13 navpičnih vreten za vrtanje - 6 vodoravnih vreten za vrtanje v osi Y - 2 vodoravnih vreten za vrtanje v osi X - 1 enota za utore v osi Y. 4-osno vrtanje v osi Y. Dimenzije in teža obdelovanca: - Širina obdelovanca (X): min. 60 mm / maks. 1000 mm - Debelina obdelovanca (Z): min. 6 mm / maks. 60 mm - Dolžina obdelovanca (Y): min. 250 mm v načinu neprekinjenega podajanja, maks. 5600 mm programirljiva dolžina obdelovanca v programski opremi - Teža obdelovanca: maks. 75 kg. Rezalna enota Profit HSK63F s 3-mestnim podajalnikom za samodejno menjavo orodja, motor 5,5 kW (S1), 1000-20000 vrt/min z frekvenčnim pretvornikom, desni in levi tek, za držalo orodja HSK63F s vpenjalno glavo 462E/OZ25, dolžina rezalnika do 130 mm. Informacije: Obdelovalna enota MultiUnit z PowerBlock z 21/23 vreteni, žago za utore in neobvezno rezalno enoto Profit. Priključna moč 12 kVA, nazivni tok 17,5 A, varovalka 32 A, napetost 400 V, 50 Hz, 3 faze (brez transformatorja). Omrežje TN ali TT. Pnevmatični priključek 7 bar (102 psi). Na napravi: hitri priključek ¼, DN7,2, medenina, na strani proizvajalca. Za napravo: priključna škatla (hitri priključek) ¼, DN7,2, medenina, na strani stranke. Dovodna cev, notranji premer cevi 12 mm (min.). Potreba po stisnjenem zraku: neprekinjena poraba zraka ca. 230 L/min (ca. 3,8 L/sek) (stisnjen zrak). Priključek za odsesavanje: 3x priključek za odsesavanje premera 80 mm. Hitrost odsesavanja: 30 m/s - merjeno na priključku za odsesavanje. Potreba po odsesavanju: min. ca. 2500 m3/h. Teža naprave: ca. 1650 kg (z dodatno opremo!). Prostor za postavitev naprave: Načeloma lahko ProTec fiksno privijemo na pod. Predpostavlja se betonsko podlago (oz. temelj) (vsaj na vseh 4 robovih/podstavkih naprave). Oprema: Protec 571 Profit HSK63F s 3-mestnim podajalnikom. Miza z valjčki 765 mm (os Y), zložljiva, za sprednjo stran naprave, širina 500 mm. Miza z valjčki 765 mm (os Y), zložljiva, za zadnjo stran naprave, širina 500 mm. Dodatni oprijem 600 mm z integriranimi valjčki za mizo z valjčki. Dodatna varnostna naprava z lamelasto zaveso. Predpostavka za horizontalno rezanje za sistem Lamello P (brez orodij za sistem Lamello P). Komplet vrtal za Protec, premer 10 mm s površino za vpenjanje (JSO). 1 karbidno svedro za pilotno luknjo 5x70 mm (dolžina 35 mm), levo # 30566-5-05035-L3. 1 karbidno svedro za pilotno luknjo 5x70 mm (dolžina 35 mm), desno #30540-5-05035-R4. 1 karbidno svedro za pilotno luknjo 5x70 mm (dolžina 35 mm), levo #30540-5-05035-L3. 1 karbidno svedro za pilotno luknjo 8x70 mm (dolžina 35 mm), desno #30540-5-08035-R. 1 karbidno svedro za pilotno luknjo 8x70 mm (dolžina 35 mm), levo #30540-5-08035-L2. 1 karbidno svedro za pilotno luknjo 10x70 mm (dolžina 35 mm), levo #30540-5-10035-L1. 1 karbidno svedro za utorne luknje 15x70 mm (dolžina 35 mm), levo #30300-5-15070-L1. 1 karbidno svedro za utorne luknje 20x70 mm (dolžina 35 mm), desno #30300-5-20070-R1. 1 karbidno svedro za utorne luknje 35x70 mm (dolžina 35 mm), desno #30300-5-35070-R. Karbidni rezalnik za utore, premer 125/30 mm, širina rezala (SB) 4,0 mm, Z=12, levo, Leitz. Samo za iverne plošče in MDF, masivni les na zahtevo in po dogovoru. Držalo orodja HSK63 F, 3 kosi. Za vpenjalno glavo 462E/OZ25, 3 kosi. Vpenjalna gl Nedpfx Aew Tfzfeltecw

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2018, številka stroja/vozila: 390.829, Funkcionalnost: popolnoma funkcionalen, obratovalne ure: 6.700 h, vhodna napetost: 400 V, vhodna frekvenca: 50 Hz, vrsta vhodnega toka: trifazni, dolžina obdelovanca (maks.): 5.600 mm, širina obdelovanca (maks.): 1.000 mm, višina obdelovanca (maks.): 60 mm, teža obdelovanca (maks.): 75 kg, število osi: 1, število mest v zalogovniku orodij: 1, vrsta aktuacije: električni, skupna višina: 1.409 mm, skupna dolžina: 1.484 mm, skupna širina: 2.325 mm, širina mize: 1.000 mm, Oprema: CE označba, Due to the acquisition of a new machine, we are offering for sale our Gannomat Protec 571 CNC machine, purchased new in 2018. The Gannomat Protec CNC machining center is a high-precision woodworking machine designed for efficient drilling, milling, and grooving operations. Engineered for versatility and accuracy, it is ideal for processing furniture components and panels. With advanced automation and robust construction, it ensures repeatable results and time savings in production. This machining center is particularly suitable for workshops aiming to optimize productivity and achieve seamless processing operations. Technical specifications: Workpiece width X: 60 - 1000 mm Workpiece length Y: 250 - 5600 mm Workpiece height Z: 6 - 60 mm Workpiece weight: 75 kg Fast machining: 21 drilling spindles Stable grooving unit: 8.3 mm saw blade width Powerful milling unit: 5.5 kW (S1), with reversible rotation direction Compact footprint: Less than 3.3 m² Supplied with the machine: - Drilling tools and 1 pc HSK63 chuck and tool for operations required in modern woodworking shops. Optional software: - Gannomat Editor office software: 1000 EUR (installation and activation by Gannomat for an additional fee) - DXF postprocessor for efficient operation: 1000 EUR (installation and activation by Gannomat for an additional fee) NOTE: Low operating hours Nsdpfxszhrdzs Altecw The price of the machine does not include VAT.

Stanje: rabljeno, Leto izdelave: 2019, Machine construction: Through-feed/return Processing size in X-direction: 1300 mm Processing size in Y-direction: 5600 mm Processing thickness (Z-dimension): 60 mm Number of main spindles: 1 unit Main spindle power: 5.5 kW Main spindle speed: 1,000–20,000 rpm Clamping system: HSK-63 F Tool changer: Pick-up changer Tool changer positions: 3 units Rear wall groove units: fixed in Y-direction Nodpsymp N Tofx Altjcw Vertical drilling spindles - in X-direction: 3 units Vertical drilling spindles - in Y-direction: 10 units Horizontal drilling spindle in X-direction: 2 units Horizontal drilling spindle in Y-direction: 6 units Control type: PC control Operating system: Windows Typewriter keyboard: Yes Mouse: Yes Programming system: Gannomat Editor DXF interface: Yes Online connectivity: Possible Table design: Fixed, smooth table Central lubrication: Automatic Tools: Various tools Operating hours: 920 hours Weight approx.: 1,800 kg Extraction diameter: 3 x 80 mm Machine was modernized at the factory; pressure beam and control technology from model 0572! Location: Customer site

Stanje: novo, Leto izdelave: 2026, Gannomat ProTec - CNC Throughfeed Machine for Drilling, Grooving, and Milling Operations Brief Overview: • Compact footprint, less than 3.3 m² • Handles large (1000 x 5600 x 60 mm) and small (60 x 250 x 6 mm) workpiece dimensions • Gentle workpiece handling through air nozzles Nedobiplrjpfx Altscw • Precision ensured by dual laser measurement and workpiece alignment • Fast processing with 21/23 drilling spindles • 21/23 drilling spindles allow for zero setup times • Robust grooving unit for saw blade widths up to 8.3 mm • Powerful milling unit 5.5 kW (S1), optional • Automatic tool changer for milling unit, optional CNC-controlled DRILLING, GROOVING, and MILLING on less than 3.3 m² with high processing precision and zero setup time – this is what the GANNOMAT ProTec stands for. TECHNOLOGY: The robust processing unit is equipped with 13 vertical drilling spindles, 8 double horizontal drilling spindles (6Y & 2X), 1 grooving saw on the Y-axis, and 1 milling unit. This configuration allows all commonly used drills/tools to be ready in a single setup and called up as required. This CNC machining center operates from below and can work in both throughfeed and return-to-operator modes. Steel support tables with air nozzles provide a reference for horizontal drilling, and, combined with robust workpiece clamps and an additional 4th axis at the drilling head, allow for highly precise drilling. A contactless laser sensor detects actual workpiece edges (top and bottom), enabling automatic correction and adjustment of the drilling program. APPLICATION AREA: ProTec offers high-end technology for both operation and application and was developed as an entry-level CNC model for small and medium-sized workshops and, alternatively, as a secondary machine to standard machining centers to prevent production bottlenecks. FIELDS OF APPLICATION: The GANNOMAT ProTec stands out for its universal application range and high customer benefit due to its excellent cost-efficiency. It is specifically designed for maximum flexibility from batch size 1 to series production, as well as for high precision with zero setup time. The GANNOMAT ProTec is designed for complete machining of cabinet side panels, cabinet bottoms, rails, back panels, furniture doors, drawer parts, drawer fronts, countertops, frame parts, tables, sliding doors, templates, and more. Examples of operations include dowel holes, row holes, mounting plate holes, connector and drawer runner bores, fittings, cabinet hanger bores, handle bores, lock bores, etc. The grooving unit enables machining of back panel grooves (also as rebates) or grooves in drawer fronts. The milling unit can perform a variety of milling tasks such as (excerpt): pockets of all kinds, tambour tracks, spot and cable pass-throughs, handle strips, plinth cutouts, recesses for cup handles and furniture locks, lock mortises, ventilation openings in doors, kitchen worktop joints as well as partial routings in, for example, kitchen worktops, furniture frame doors, and much more. Another possible application of the ProTec is the routing of standard milling contours traditionally produced with templates and manual routers. Materials such as chipboard, solid wood, multi-layer boards, lightweight panels, etc., can be efficiently processed with the ProTec.

Stanje: rabljeno, Leto izdelave: 2014, Rabljen stroj Letnik izdelave: 2014 Oprema in tehnični podatki: popolnoma v standardni izvedbi z: - Nosilec z linearnim vodilom, sestavljen iz: 1 kos enovretenske horizontalne vrtalne enote, motor 0,65 kW, gib 70 mm Hitrost orodja je izbirljiva prek uporabniške programske opreme (3000/5000/8000 vrt/min) 1 kos postaje za vpihovanje, nanašanje lepila in vstavljanje lesnih čepov za čep premera 8 mm, dolžina čepa 25–50 mm - Popolnoma avtomatsko, elektronsko upravljano centralno mazanje - Os X, upravljana s CNC, z dolžino delovnega območja 1300 mm, hitrost gibanja največ 105 m/min - Os Z, ročno nastavljiva prek mehanskega digitalnega številčnega prikazovalnika, položaj prek oporne mize 5–40 mm - Previs čepa za vstavljanje, 7–20 mm, nastavljiv prek mehanskega digitalnega številčnega prikazovalnika, globina vrtanja 0–35 mm (pri dolžini svedra GL 70 mm) se samodejno nastavi z previrom za vstavljanje - Zaprt sistem za nanašanje lepila s tlakom lepila 6 bar prek šobe za lepilo, za lepila z viskoznostjo od 150 do 350 mPas - Količina lepila je brezstopenjsko nastavljiva prek uporabniške programske opreme - Izbirno stikalo LEPILO/VODA za čiščenje sistema za nanašanje lepila, vsaka možnost vsebuje: 1 rezervoar iz nerjavečega jekla za 7,5 kg lepila in 7,5 l vode - Nadzorna lučka za prikaz ostanke lepila v rezervoarju za lepilo - 1 kos stranski opornik na levi strani, 1 kos stranski opornik na desni strani in 1 kos sredinskega opornika (vsi odstranljivi) - 4 kos gumbov za vklop za posamično obdelavo 1–4 obdelovancev - 4 kos pnevmatskih nagibnih vpenjalnih valjev 10° za debelino obdelovancev do največ 80 mm, dolžina obdelovanca (Y) najmanj 70 mm - 1 kos sesalne komore, priključek Ø 80 mm - 1 kos nadzora TCT z: Vgrajenim industrijskim osebjem računalnikom, vključno s programljivo logično enoto (PLC) tipa Beckhoff TWINCAT, območje delovne temperature 0–50 °C, Industrijski zaslon TFT 15“ na dotik, kapacitivni, operacijski sistem: WINDOWS 7 - Programiranje prek uporabniku prijazne programske opreme, razmak med vrtinami je prostovoljno programirljiv z absolutnimi, relativnimi ali raster merskimi enotami, samodejna zrcalna obdelava obdelovanca in optimizacija delovnega postopka, 4 delovna polja, ki jih je mogoče opremiti z različnimi programi, grafična predstavitev obdelovanca, parametrično programiranje, premik ničelne točke, programirljivi seznami opravil, diagnoza napak s preprostim besedilom Dodatna oprema: - 1 elektronski, optični sistem za nadzor nanašanja lepila G.I.C. (Glue Insert Control) za 1 kos šobe za nanašanje lepila Nedpfezlbrvsx Altecw - 1 os Z z dinamičnim položajem, ki ga nadzoruje CNC, za nastavitev višine vrtalne in vstavne postaje za čep (programirljivo od 5 do 40 mm), hitrost gibanja največ 30 mm/s - 1 enovretenska navpična vrtalna enota, vrtanje OD ZGORI, 0,65 kW, (3000/5000/8000 vrt/min), položaj (Y), ročno nastavljiv prek mehanskega digitalnega številčnega prikazovalnika od 5 do 40 mm, globina vrtanja (Z) največ 30 mm (pri dolžini svedra GL 57 mm), debelina obdelovanca (Z) največ 50 mm, dolžina obdelovanca (Y) najmanj 130 mm (vključno s kompenzacijo globine vrtanja, npr. za Häfele Minifix) - 4 navpični nagibni vpenjalni valji 10° z nosilcem - 1 tipkovnica z nosilcem Razpoložljivost: po dogovoru; trenutno se v tovarni Ganner prenavlja Lokacija: Avstrija

Stanje: rabljeno, Leto izdelave: 1985, Rabljeni stroj Leto izdelave: 1985 Oprema in tehnični podatki: - Za konstrukcijske izvrtine horizontalno in vertikalno - Za vrtanje vrst lukenj vertikalno z razmakom 32 mm - Vertikalni vrtalni agregat z dvo-vretenskimi glavami, prosto pozicioniranimi na indeksni osi Nedpfxezk N Dwe Altocw - Motor 1,5 kW s 1400 vrt/min - Motor 1,5 kW s 2800 vrt/min - Vrtalne glave s pnevmatskim pomikom - Pnevmatski vpenjalci materiala - Prehodna širina pribl. 850 mm - Vključno z različnimi omejevalniki in svedri Razpoložljivost: takoj Lokacija: Röllbach

Stanje: rabljeno, Leto izdelave: 1986, Rabljeni stroj Leto izdelave: 1986 Oprema in tehnični podatki: Ncsdjzk N Agjpfx Altsw - z vrtalno glavo za vrste lukenj s 7 vreteni in zatiči za pozicioniranje - razdalja 32 mm - z vrtalno glavo za BLUM tečaje - z vrtalno glavo za Hettich tečaje - z ustreznimi vtisnimi matricami - motor 400 V, 0,75 kW, 2800 obr/min - z naslonskimi palicami Razpoložljivost: takoj Lokacija skladišča: 63934 Röllbach

Stanje: rabljeno, Leto izdelave: 1997, Rabljeni stroj Letnik: 1997 Ncjdpfozk Nuisx Altow Stanje: vzdrževan Oprema in tehnični podatki: - Število vrtalnih vreten: 21 kosov v razmiku 32 mm - Smer vrtanja: od spodaj in s čelne strani - Nagib: 0-90 stopinj z ročnim kolesom - Pnevmatski vpenjalci materiala: 3 kosi - Prehod: maksimalno 100 mm v višino in maksimalno 640 mm v širino - Motor: 1,5 kW - Premer odsesovanja: 120 mm - Vključno z različnimi omejilniki (glej slike) Razpoložljivost: takoj Lokacija skladišča: Röllbach

Stanje: novo, Leto izdelave: 2026, AREA - CARCASE PRESS GANNOMAT "CONCEPT 70 EASY 170" Ncsdpfx Aow Sgnksltow Complete in standard version with: - Sturdy, torsion-resistant frame made of steel, welded and bolted construction - SIDE press beam with continuous pressure surface and 25 mm thick, coated support plate - Counterpressure surfaces (side pressure wall, bottom) are 25 mm thick, coated, continuous support plates - Electromotive adjustment of the press beam via precision trapezoidal-thread spindles (with increased pitch and running accuracy) and high-performance slide nuts with grease reservoir - Pressing is performed electromotively via worm gear motor (0.75 kW) - Pressing force of the press beam can be continuously adjusted electronically via potentiometer and regulated via frequency inverter, therefore press force control is completely wear-free - Press force for vertical press beam min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Press and adjustment speed of the press beams with fine positioning, via 3-position selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of the press beam, e.g., for low pressing forces such as drawers, etc. - Very easy operation via two separate pushbuttons; two motion sequences (open/close) can be selected via the controller - Freely adjustable pressing time preselection 0-30 min (switchable to seconds or hours) with individually programmable opening dimensions for both press beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Availability: short-term

Stanje: novo, Leto izdelave: 2025, GANNOMAT “MASTER 325” FRAME DOWEL AND MORTISE DRILLING MACHINE ESPECIALLY DESIGNED FOR STAIRCASE CONSTRUCTION Complete in standard specification according to price list 01/19/D, including: - Precision collet chuck for ER40 collets, Ø 3-26 mm incl. collets Ø 10 / 13 / 16 / 20 - Two-speed motor 1400/2800 rpm, 1.5 kW - Line laser with mount - Drilling unit, infinitely rotatable from the front (65°-0°-65°) - Position setting via digital counter - Position adjustment for 2 levels, pneumatic (0-100 mm) - Maximum drilling depth: 200 mm - Precision index rail with 12 mm pitch and center locking, and cross adjustment 320 mm - Complete stop system including: 1 center stop and 1 stop for extra-wide frames 1 stop bar, approx. 850 mm long (can be reversed from left to right) 2 folding stops - Height-adjustable mortising unit with 2 program cams (400V, 3Ph, 50Hz, 1.5kW) Dust extraction hood, dust-tested, Ø 80 mm Double mitre stop, adjustable 0°-60° Pneumatic clamping of X-axis with on/off switch at the indexing lever Pair of workpiece support arms, swiveling (left and right) Clamping column can be repositioned to the front Chassis with 4 wheels for easy movement of the machine Ncodpfxexdttpe Altew 1 piece Collet extension Ø 20 mm, incl. collet for drill shank Ø 9 mm 1 piece Spindle drill bit Ø 25 mm, made of chrome steel, with centering point Available: short notice

Stanje: novo, Leto izdelave: 2026, Gannomat Concept 70 Eco Lamella case clamp with rapid traverse Technical Specifications: Lamella case clamp from our showroom; Working range: width from 150 to 2,500 mm, height from 150 to 1,400 mm; depth 700 mm; - Top lamella pressure beam with 6 elements, side lamella pressure beam with 5 elements - Lamella pressure beams with proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are continuous 40 mm thick, coated support plates - The pressing force of the pressure beams is infinitely adjustable electronically via 2 potentiometers and set via a frequency converter—thus, torque transmission is absolutely wear-free. - Pressing force for the horizontal pressure beams: min. 500 daN (kg) up to infinitely adjustable max. 2200 daN (kg) Ncjdpfoy Egz Sjx Altew - Pressing force for the vertical pressure beams: min. 300 daN (kg) up to infinitely adjustable max. 2200 daN (kg) - Including options: Rapid traverse speed for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams; pressing speeds 5/10/25 mm/sec and rapid traverse speed 50 mm/sec. The sensors can be deactivated for pressing special parts. - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and 45° carcasses. Simple operation via 6 separate push-buttons, freely selectable pressing time preselection with automatic opening, loading height 300 mm. The machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Stanje: novo, Leto izdelave: 2025, CNC-controlled boring, gluing, and dowel inserting machine Ncjdow Sgm Hspfx Altow fully equipped in standard configuration with: - Support with linear guide, consisting of: 1 pc. single-spindle horizontal drilling unit, motor 0.65 kW, stroke 70 mm Tool rotation speed selectable via operator software (3000/5000/8000 rpm) 1 pc. blowing, gluing, and dowel insertion station for dowels ø 8 mm, dowel length 25-50 mm - Fully automatic electronic central lubrication system - X-axis CNC controlled, working length 700 mm, maximum traversing speed 95 m/min - Z-axis adjustable manually via mechanical digital counter, position over support table 5-40 mm - Dowel insertion projection adjustable from 7-20 mm via mechanical digital counter, drilling depth from 0-35 mm (with drill length GL 70 mm) automatically set with projection - Closed glue system with 6 bar glue pressure via glue nozzle, for adhesives with a viscosity of 150 to 350 mPas - Glue quantity infinitely adjustable via operator software - Selector switch GLUE/WATER for flushing the glue system with: 1 stainless steel container for 7.5 kg glue and 7.5 l water - Indicator lamp for remaining glue level in the glue tank - 1 left side stop, 1 right side stop (both removable) - 2 start buttons for individual operation with 1-2 workpieces - 2 pneumatic angular clamping cylinders 10° for workpiece thickness up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 extraction funnel, connection ø 80 mm - 1 TCT control with: Built-in industrial PC, incl. Soft PLC type Beckhoff TWINCAT, operating temperature range 0-50°C, TFT industrial display 15" capacitive touchscreen, operating system: WINDOWS 10 IoT LTSC (long term support channel) - Programming via user-friendly menu software, freely programmable drilling distances with ABSOLUTE, RELATIVE, or GRID measurement, automatic workpiece mirroring and process optimization, 2 work areas assignable with different programs, graphic workpiece representation, parametric programming, zero-point displacement, programmable work lists, plain-text error diagnostics - Integrated options: - Electronic optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle Art.no. 0470-0810 - 1 EASY CLEAN system for automatic test glue shots before starting the drilling/gluing/dowel inserting work program. E.C.S. for 1 glue nozzle Art.no. 0471-Z010 - 1 single-spindle vertical drilling unit, top drilling, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjustable via mechanical digital counter Adjustable from 5-40 mm, drilling depth (Z) max. 30 mm (with drill length GL 57 mm) Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (incl. drilling depth compensation e.g. for Häfele Minifix) Art.no. 0471-0830 - 4 additional vertical angular clamping cylinders 10° with bracket, Art.no. 0470-0850 Available: at short notice

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2025, GANNOMAT "JUNIOR 323" FRAME DOWEL AND MORTISE BORING MACHINE Completely in standard configuration as per price list 01/22/D with: - Precision collet chuck for ER 40 collets, diameter 3–26 mm. Including collets Ø 10 / 13 / 16 / 20 mm - Motor 1.5 kW, 2800 rpm - Position adjustment via digital counter - Position adjustment for 2 levels, pneumatic (0–100 mm) - Maximum drilling depth 150 mm - Precision indexing rail with 12 mm increments, featuring: - Central detent and transverse adjustment 320 mm - 2 pneumatic safety clamping cylinders - Complete stop system, consisting of: 1 central stop and 1 stop for extra-wide frames 1 stop bar, approx. 850 mm long (can be repositioned from left to right) 2 flip stops - Lowerable mortising device with 2 program cams (400V, 3Ph, 50Hz, 1.5 kW) Ncjdpexdttijfx Altjw Extraction funnel, diameter 80 mm, dust-tested Central mitre stop 45° Pair of auxiliary workpiece supports, swiveling (left and right) Drilling head mount 3-spindle drilling head, 32 mm pitch (can be rotated 90°) Undercarriage with 4 wheels for easy movement of the machine Availability: Short term – immediately –

Stanje: kot nova (razstavni stroj), Leto izdelave: 2026, - NEW - Manufacturer: Ganner Gannomat Model: SELEKTA 253 220 V, 1 Ph, 50 Hz Complete in standard configuration with: - Fully automatic electronic control with program selector switch: RINSE - GLUE - GLUE/INSERT - Dowel feed via electronic vibratory feeder with potentiometer for stepless adjustment of dowel feed rate Ncsdpfx Ajdwi Rkjltsw - Automatic dowel diameter and length control with Auto-DL-Select system (automatic ejection of incorrect dowel lengths +/- 5 mm into collection container) - Closed glue system with 6 bar glue pressure via glue nozzle for adhesives with viscosity from 150 to 350 mPas - Stepless electronic glue quantity adjustment with potentiometer via electronic system time preselection - Selector switch GLUE/WATER for rinsing/cleaning the glue system with EasyClean function button (automatic cleaning program for glue hose and glue nozzle via spray funnel and waste water collection container) - Indicator light for glue remaining quantity display in glue container - 1 stainless steel container for 5 kg of glue and 1 stainless steel container for 5 l of water for rinsing/cleaning - 4 castors for moving the machine Including 1 gun for dowels Ø 8 mm, dowel length 25 - 40 mm, insertion overhang 7 - 20 mm Air connection: 6 bar Price ex stock 54634 Bitburg - immediately available -

Stanje: novo, Leto izdelave: 2025, Gannomat Concept 70 Eco Lamella Case Clamp with Rapid Traverse Technical Data: Lamella case clamp from our showroom; Working range: Width from 150 to 2,500 mm, height from 150 to 1,400 mm; depth 700 mm; - Upper lamella pressure beam with 6 elements, lateral lamella pressure beam with 5 elements - Lamella pressure beams with proven tolerance compensation for tightly glued carcass joints - Counterpressure surfaces: continuous, coated support plates, 40 mm thick - Pressing force of the pressure beams is infinitely electronically adjustable via 2 potentiometers and set using a frequency converter, ensuring absolutely wear-free torque transmission. - Pressing force for horizontal pressure beams: min. 500 daN (kg) up to infinitely adjustable max. 2,200 daN (kg) - Pressing force for vertical pressure beams: min. 300 daN (kg) up to infinitely adjustable max. 2,200 daN (kg) - Included Option: Rapid traverse speed for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors integrated in the pressure beams. Pressing speeds: 5/10/25 mm/sec; rapid traverse speed: 50 mm/sec. Sensors can be deactivated for special workpiece clamping. - Jog mode for precise positioning of both pressure beams, e.g., for low pressing forces, drawer boxes, and 45-degree carcasses. Simple operation via 6 separate pushbuttons. Freely adjustable pressing time pre-selection with automatic opening, loading height 300 mm. The machine is on display at our showroom and available for immediate delivery. Ncedpfx Aeiidm Neltjw Location: ex stock 54634 Bitburg - available immediately -

Stanje: rabljeno, Leto izdelave: 2000, Število vreten po vrsti lukenj: 11 Število vodoravnih vreten: 3 Glava za lončane tečaje: da, Blum Razmak med svedri: 32 mm Nsdpjxc Hi Uefx Altocw Poraba energije: 2,2 kW Vrtalni agregat: vrtljiv

Stanje: rabljeno, Used machine Used line boring machine Ganner Compact 30 Features and technical data: Njdpfezk Nwdex Altocw - 2 drilling beams, each with 15 spindles - 32 mm pitch - Drilling unit position adjustment: 0 - 650 mm - Minimum distance between the rows of boreholes: 190 mm - Spindle speed: 2800 rpm - Motor power: 2 x 0.75 kW - Maximum clamping height of workpieces: 70 mm - Working height: 850 mm - Compressed air connection: 6 bar Availability: by arrangement Location: Solingen

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 1990, Engines: 2 x 1.85 A, 50 Hz, 380 V, 2800 rpm Nodpfev Nptmjx Altjcw Operating air pressure: 6 bar 30 spindles, holder Ø 10 mm Combined foot switch Emergency stop switch Main switch Manual height adjustment Manual lateral adjustment

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 1982, Funkcionalnost: popolnoma funkcionalen, two speeds: 1400 rpm at 1.1 kW, 2800 rpm at 1.5 kW air connection 6 bar fully automatic pneumatic control with foot pedal Ncedpjv Npw Esfx Altew additional switch for "chip removal" program T-drilling head with 7+2 drilling spindles, 32 mm pitch drill shank diameter 10 mm swivable 90°, with locking mechanism undercarriage

Stanje: dober (rabljeno), Leto izdelave: 1982, Funkcionalnost: popolnoma funkcionalen, Power supply: 380V, 3.3A Motor power: 1.1 kW, 2800 rpm automatic pneumatic control with control panel Drilling head with 23 spindles, 32 mm pitch Adjustable drilling depth Drill shank: 10 mm Position adjustment: 5–60 mm Clamping height: 80 mm Pass-through width: 800 mm Dimensions: 1200 x 900 mm Ncjdpfjq Auwtex Altew Weight: approx. 400 kg Includes: 1x row drilling setting gauge 1x side stop setting gauge 1x stop ruler 1500 mm 1x stop ruler 2000 mm

Stanje: delavnici obnovljeno (rabljeno), Funkcionalnost: popolnoma funkcionalen, Drilling and insertion machine for all types of furniture fittings; row drilling and group drilling machine in the 32 mm system. Power supply: 400V, 0.75kW Spindle speed: 2800 rpm Stop rule: 960 mm 2x swiveling stops For drills with 10 mm shank diameter Maximum workpiece thickness: 40 mm Nsdoumw Sbopfx Altecw Includes: 1x 7-spindle drilling head for row drilling with 32 mm pitch, equipped with integrated positioning pins Manual feed Base frame included Available at extra cost: Olive (handle) drilling head: €450.00 Mepla drilling head with press-in die: €550.00 Hettich drilling head with press-in die: €550.00

Stanje: rabljeno, Leto izdelave: 2017, Število vrtalnih vreten: 21 kos Razmak: 32 mm Vpenjanje svedra: vpenjalna površina stebla svedra: 10 mm Upravljanje: nožni pedal Orodja: da Smer vrtanja: od spodaj in čelno Zasuk: ročno Kot zasuka: samo 0° ali 90° Maks. višina prehoda: 80 mm Maks. širina prehoda: 750 mm Število vpenjalcev materiala: 3 kos Vrsta vpenjanja materiala: pnevmatsko Ncedpfx Aleihghretsw Izvedba: stacionarno Sistem zaustavitev: samo za konstrukcijsko serijo Teža približno: 400 kg Moč motorja: 1,5 kW Premer odsesovalnega priključka: 120 mm Skladiščna lokacija: pri stranki

Stanje: rabljeno, Leto izdelave: 2024, New demonstration machine! List price: €32,665 – Complete in standard configuration with: Sturdy, torsion-free steel frame in welded and bolted construction – TOP lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements – Lamella pressure beams feature the proven Ganner system tolerance compensation for tightly pressed carcass joints – Counterpressure surfaces (side pressure wall, base) are continuous, 38 mm thick, coated support panels – Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam – Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir – Pressing is performed electromechanically by two separate worm gear motors (2 x 0.75 kW) – Pressing force of the pressure beams is infinitely adjustable via two potentiometers and regulated by frequency converters, making the pressure regulation absolutely wear-free – Pressing force for the horizontal beam: min. 500 daN (kg) up to max. 2200 daN (kg), stepless – Pressing force for the vertical beam: min. 300 daN (kg) up to max. 2200 daN (kg), stepless – Pressing and adjustment speed of the beams with fine positioning, selectable via 3-step switch: 5 / 10 / 25 mm/second – Simple operation via 6 separate push-buttons, 8 movement sequences selectable via control unit – Freely adjustable pressing time preselection with automatic opening (0–30 min, switchable to seconds or hours) – Working height/loading height: 300 mm – Working dimensions: Length min: 150 mm, max: 2500 mm | Height min: 150 mm, max: 1400 mm | Depth: 700 mm – Weight: approx. 1800 kg net – Dimensions (L x W x H): 3.45 m x 0.95 m x 2.30 m – Electrical connection: 400V, 3Ph, 50Hz (3.2 kVA, 16A). Nedpfx Asuf Hx Heltjcw Additional features: Rapid traverse speed for quick positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams. Pressing speeds: 5 / 10 / 25 mm/sec and rapid traverse: 50 mm/sec. Sensors can be deactivated for pressing custom parts. 1 set of machine feet (working height 500 mm). Location:

Stanje: zelo dobro (rabljeno), Gannomat stroj za vrtanje dolgih lukenj / stroj za vrtanje čepov z motorjem Leroy-Somer - Tip motorja: LS80L2 - Moč: 1,1 kW - Število vrtljajev: 2810/min - Napetost: 220/380 V - Frekvenca: 50 Hz Nsdpfjy Saw Hjx Altscw - Razred zaščite: IP54 3-fazni pogon - Stabilna delovna miza - Precizna vodila - Nastavljivi omejevalniki - Robustna kovinska konstrukcija - Idealno za serijsko delo in natančne lesene spoje – z vrtalnikom in lončastim rezkarjem - Tlak zraka je potrebno zapreti ročno