Balirka s sistemom za odsesavanje prahu

mütek

Leto izdelave: 2025, stanje: novo, Granulator MVZ 7.5 kW Demonstration unit available at special price Our Granulator MVZ 7.5 is suitable for shredding thin-walled plastic parts or for the secondary size reduction of wood chips. More details can be provided after testing with your material. Our granulators are used for size reduction of a wide range of materials, such as plastics or wood. Shredders and granulators are suitable for a variety of shredding tasks. For example, in injection molding machines, scrap parts and sprues are produced that need to be recycled. In blow molding machines, along with scrap parts, trim waste or start-up parisons must be processed. Materials such as PET bottles, PE/PP bottles, canisters or buckets, and pipes from blow molding can be processed. Material is fed from above via a hopper into the grinding chamber of the granulator. The internal rotor is equipped with knives. The material is shredded between the rotating knives and the stationary knives mounted in the grinding chamber housing until it passes, as defined regrind, through the screen located below the rotor. *Option: The ground material is usually pneumatically conveyed to big bags, silos, or other containers. The price applies only to the size reduction unit as shown in image 1 - Fan, cyclone, and filter are optional components. --- Technical Data: Granulator MVZ 7.5 kW Motor: 7.5 kW *Larger machines available on request (4 to 75 kW) Throughput up to 120 kg/h when shredding plastics *highly dependent on screen size and material Application example: Shredding of PE 1000 plastic Input material: approx. 40 mm chip length Secondary shredding to approx. 6 mm Throughput up to 50 kg/h with a 6 mm screen (Throughput up to 80 kg/h with an 8 mm screen) ___ Significantly higher throughputs can be achieved when re-shredding G 30 wood chips. Up to a maximum of 400 kg/h with a 10 mm screen *metered feed, e.g., via conveyor belt or auger. Details available after a test run with approx. 30 kg. Rotor diameter: 180 mm 6 rotor knives, each 225 mm 4 stator knives, each 225 mm Dimensions: 930 x 730 x 1420 mm Weight: 450 kg Suction nozzle: 100 mm Screens: 5, 6, 8, 10, 12, and 15 mm – other sizes available on request Price per screen: €390 Price for replacement knife set: €679 Suitable for example for: - All types of plastic waste Various materials – HDPE, LDPE, PP, PS, PC, PA - Biomass - Wood - Herbs etc. Parts from injection molding, blow molding, injection molding scrap, small bottles, cables, small pipes, profiles, etc. --- Larger units available as options: Granulator MVZ / 18.5 kW Throughput up to 350 kg/h *dependent on screen and material Opening: 620 x 400 mm Goded N Dn Djpfx Anfjbl *optional with matching extraction/conveying system Granulator MVZ / 30 kW Throughput up to 400 kg/h *dependent on screen and material Opening: 620 x 500 mm *optional with matching extraction/conveying system --- To select the right machine, the following information is required: - Length x width x height of the feed material? - Required screen size (final output size in mm)? - Required throughput per hour in kg? - Wall thickness in mm? - Material description Photos can also be helpful

Stanje: dober (rabljeno), Manufacturer: Haver & Boecker Documentation available Gjdjv Sz Tdjpfx Anfobl Mechanical conversion from 50 kg to 25 kg bags in 1999 Control system: Siemens S7 Upgraded to the latest standard with spare parts support in 2015 Supported bag types: quicklime, hydrated lime, cement, gypsum

Stanje: novo, Leto izdelave: 2026, * Optional features available at extra cost, see below * Production time approx. +/- 6 months The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are characterized by their robust construction, ensuring consistent briquette quality during continuous operation. The compaction process takes place without the addition of binding agents—solely via hydraulic pressing force. Depending on the material, the input material volume can be reduced by up to 90%. The standard silo holds approx. 0.5 m³, but larger silos or special containers for installation below an existing extraction and filter system as a complete disposal unit are also available. Depending on customer requirements, MPP NEM individual machines can be combined into a complete system. The chip hopper of the press can be loaded manually, via conveyor belt, via dust extractor, or with a tilting container trolley. For systems intended for fully automatic operation, the use of a lift-and-tilt device, in conjunction with a shredder, is recommended. The MPP NEM briquetting presses are designed for the production of briquettes from homogeneous material. The length of a briquette depends on the model and ranges from 40 to 80 mm, and the diameter varies by type (50, 65, or 70 mm). To recover emulsions, the briquetting press can be equipped with a drip tray, allowing coolants, cutting fluids, and lubricants to be collected and recovered. Non-ferrous metal chips up to approx. 20 mm in length are filled into the briquetting press's feed hopper. An agitator is built into the bottom of the hopper to prevent bridging and feed the material into the pre-compaction chamber. In this chamber, a hydraulic ram pre-compacts the material and pushes it into the press block. The main press cylinder then compresses the material against a vertical slide until the set pressing pressure is reached. The vertical cylinder subsequently lifts, and the finished, stable briquette is ejected. The more homogeneous the input material, the more uniform the briquette lengths. Advantages of briquette production include: - Volume reduction by up to 90% - Emulsion recovery - Cost savings on storage and transport - Economical disposal - Profitable resale Godpfsgfm Ryjx Anfsbl Briquetting Press NEM 900: For briquetting aluminum chips Throughput capacity: up to 350 kg/h max (material-dependent; chip length less than 10 mm) Last test with aluminum chips < 18 mm: approx. 260 kg/h *More details available after a free test with your material. Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm Technical data: Total connected load: approx. 31 kW Continuous operation: approx. 22 kW 400 Volt / 50 Hz / 3-phase Pump: 120 + 60 litres per minute Silo: 1 m³ Silo diameter: 1200 mm Including agitator Oil tank: 600 litres Dimensions (LxWxH): 2500 x 1700 x 1730 mm Weight: 2250 kg Hydraulic pre-compaction via ram Main press cylinder Vertical cylinder Prepared for connection to a cooling unit

Stanje: novo, Leto izdelave: 2026, Our best-selling briquetting press – the classic choice. + Proven, simple technology for extremely low failure rates + 25 years of experience, ongoing development, and expertise + Several thousand machines in operation with satisfied customers Gbsdpfx Anjgl Nlmefel + Outstanding price-performance ratio Optional extras (available at additional cost): *Surcharge for fill level sensor, enabling automatic operation: + €995 net *Surcharge for large pre-compression chamber + €970 (Recommended for very light materials such as straw, increases machine width by 13 cm) Briquette diameter: 50 mm Front bushing: 50 mm Max. briquette stroke: 40 mm Optimal briquette stroke: 40 mm Throughput (material dependent): up to 60 kg/h* *Depending on bulk density *Based on a bulk density of 200 kg/m³ Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1,680 mm Width: 1,100 mm Height: 1,500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1,000 mm Silo capacity: approx. 0.7 m³ Pump output: 37 liters Hydraulic pre-compressor Press tongs cooling option: No Hydraulic oil cooling option: Yes Fill level monitoring option: Yes CE compliant Raw material requirements: - Moisture content (atro) must be between at least 6% and max. 18% - Maximum chip length 15 mm - Installation temperature: Tempered room, at least +5°C - Customer must provide protection against hydraulic oil loss - Material feed must be free from metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may result

Leto izdelave: 2003, stanje: delavnici obnovljeno (rabljeno), Stock number: 2651 1 used, partially overhauled in 2023, underwater pelletizing system Gjdpfxoiyyf Io Anfjbl Throughput up to approx. 450 kg/h depending on material, consisting of: Type BKG (Nordson) Start-up valve with hydraulic unit Granulator type A300 incl. die plate and cutter bar, drive 4.4 kW By-pass system TVE 1000 ED pellet dryer, drive 4 kW incl. Agglomerate catcher Temperature-controlled water system with Water tank 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15 m³/h Heat exchanger Control system Further UWG pelletizers available ex works Wuppertal (Gala, BKG Nordson, Econ) Available from stock Wuppertal: Complete compounding and pelletizing lines with single-screw or twin-screw extruders.

Stanje: novo, Leto izdelave: 2026, Availability upon request Very robust machine with high pressing force - also suitable for producing marketable briquette quality *depending on material. This is made possible by the large-dimensioned press cylinder and the 70 mm briquette size. Our best-selling briquetting press series + Proven, simple technology, ensuring extremely low susceptibility to failure + 25 years of experience, continuous development, and know-how + Several thousand machines in operation with satisfied customers + Excellent value for money Optional demonstration cooling unit surcharge: + €4,980 net (can also be retrofitted later) * Cools the press clamp (important from 4 hours of operation) and the hydraulic oil * Cooling unit recommended for regular operation exceeding 4 hours continuously Godpfx Anod Nm Siefebl Commodity code: 84793010 Briquette diameter: 70 mm Front sleeve: 125 mm Max. briquetting stroke: 100 mm Optimal briquetting stroke: 80 mm Capacity (material-dependent): up to 150 kg/h* *depending on bulk density *based on a bulk density of 200 kg per cubic meter Motor output: 9.2 kW 400 Volt / 50 Hz / 3-phase Length: 2,095 mm Width: 1,300 mm *with large chamber 1,600 mm Height: 1,700 mm Weight: 1,250 kg Oil volume: 220 liters Silo diameter: 1,200 mm Silo capacity: approx. 1 m³ Pump: 75 liters Hydraulic pre-compressor Press clamp cooling option: yes, with optional coolable press clamp Hydraulic oil cooling option: yes Cooling of press clamp and hydraulic oil possible with optional cooling unit Level monitoring option: yes Continuous strand briquette option: yes (material-dependent) Enlarged filling slider option: yes, with optional enlarged filling slider CE compliant Raw material requirements: - Moisture content (atro) must be between at least 6% and a maximum of 18% - Maximum chip length: 20 mm - Installation temperature: heated room with at least +5°C - Material feed must be free from metals and mineral contaminants such as sand, stones, etc. Damage to the pressing tools and/or increased wear may otherwise occur

Stanje: novo, Leto izdelave: 2026, obratovalne ure: 8 h, Availability upon agreement Very robust machine with high pressing force - Also suitable for producing a marketable briquette quality *depending on material. The large-dimensioned pressing cylinder and the 80 mm briquette diameter make this possible. Gbjdpfx Aexfwdenfsl Our bestselling briquetting press series + Proven, simple technology for extremely low susceptibility to faults + 25 years of experience, ongoing development, and expertise + Several thousand machines in operation with satisfied customers + Excellent price-performance ratio Surcharge for cooling unit + €4,995 net (can also be retrofitted later) * Cools the pressing tongs and hydraulic oil (recommended if the press is operated continuously for more than approx. 3.5 hours without pause) Briquette diameter: 80 mm Front bush: 125 mm Maximum briquette stroke: 100 mm Optimal briquette stroke: 80 mm Throughput (depending on material): up to 200 kg/h* *depending on bulk density *based on a bulk density of 200 kg per cubic meter Motor power: 9.2 kW 400 Volt / 50 Hz / 3-phase Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo capacity: approx. 1 cbm Pump: 75 liters Hydraulic pre-compressor Press jaw cooling option: yes, with special accessory coolable press jaw Hydraulic oil cooling option: yes Cooling of press jaw and hydraulic oil with cooling unit (special accessory) Fill level monitoring option: yes Continuous briquette option: yes (material dependent) Enlarged filling slider option: yes, with special accessory enlarged filling slider CE compliant Requirements for raw material: - The moisture content (atro) must be at least 6% and not exceed 18% - Maximum chip length 20 mm - Installation temperature: heated environment, at least +5°C - The feedstock must be free from metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and/or increased wear may occur as a result.

Stanje: novo, Leto izdelave: 2025, Sheet Metal Decoiler Cantilever 500mm - Load capacity: 1,500 kg - Inner Ø: 480–530 mm - Decoiler mandrel with 4 tensioning arms, ball bearing-mounted, with disc brake - Maximum coil width: 500 mm Godpsfvbxqjfx Anfobl

Stanje: novo, Leto izdelave: 2026, Production time approx. +/- 4 months. The ideal machine, for example, for shredding pallets and wood waste. * prepared for extraction, see pictures 4 and 5 without additional accessories such as -exhibited hopper or -conveyor belt cutout Commodity code: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 phase incl. turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3 phase Knives: 76 pieces, reversible multiple times Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control system: Siemens S7-1200 PLC Hopper opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 cbm Hydraulically operated pusher Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (LxWxH) approx. 2765 x 2520 x 1730 mm Turbo coupling Gedpfxjd Hkqhe Anfebl Standard equipment includes: - V-rotor for maximum throughput - 2nd row of knives on rotor - Control cabinet with Siemens PLC control system - Automatic star/delta start - Fast hydraulic system - Automatic shutdown when rotor is idling - Rotation speed 70-90 rpm for high throughput - Cycle control to avoid idle time - Performance-enhancing step control for hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration dampening machine feet - CE compliant The shredder is designed for shredding natural wood, chipboard and MDF, other materials upon testing and approval by the manufacturer. Requirements for raw material: - Moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Stanje: novo, Leto izdelave: 2025, The ideal machine for shredding both hardwood and softwood Another machine, available immediately (ex works Neckartailfingen) . Motor: 18.5 kW; 400 V - 50 Hz - 3 phase, Blades: 14+2 pieces, 40x40 mm, multiple cutting edges (rotatable), Rotor diameter: 260 mm, Control: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume approx. 0.6 m³, Hydraulically operated pusher Screen perforation of your choice (12 - 40 mm) Extraction port Ø 160 mm Weight approx. 1,300 kg Dimensions (L x W x H) approx. 1737 x 1167 x 1650 mm Gsdpfod E R D Sox Anfobl . The following options are available at extra cost: - Additional blade row + €1,990 net (28 instead of 14) - Surcharge for segmented floor, 4-sided + €2,170 net (Prevents the pusher from jamming. Recommended for material thickness less than 3 mm) - Shredder height increase by 30 cm (for conveyor belt integration) + €1,980 net - Angle conveyor (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (synchronized start/stop with the shredder) - Special bearing + €1,540 net (rarely needed. Sealed, even more robust rotor bearing. worth considering for screens below 15 mm and/or high fines content. Not necessary if bearings are lubricated with grease approximately every 2 weeks in operation) . Requirements for raw material: - The moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. will lead to increased wear. . We are happy to offer a free test using your material. For this, we invite you to visit us in Neckartailfingen. Alternatively, you may send your material to us by freight and we will document the test process with photos and videos.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2003, Funkcionalnost: popolnoma funkcionalen, Well-maintained EMCO Hyperturn 665 MC Plus for sale, equipped with IEMCA Master 880MP-E bar feeder, chip conveyor, and high-pressure coolant pumps! Machine was used exclusively for brass components! CNC Turning and Milling Center | EMCO - HYPERTURN 665 MC Plus with main/ sub-spindle, C + Y axis, 2 turrets each with 12 positions for live tooling! Technical data: Swing diameter over bed: 600 mm Swing diameter over cross slide: 500 mm Control: Siemens Sinumerik 840 D Max. turning diameter: 430 mm Max. turning length: 744 mm Max. bar diameter: 65 mm Travel – X: 270 mm Travel – Z: 750 mm Travel – X2: 205 mm Travel – Z2: 750 mm Travel – Y: 100 (+/- 50) mm Main spindle speed: 0 - 5,000 rpm Sub-spindle speed: 0 - 7,000 rpm Tool turret: 2 x 12 positions, all live! Tool mounting: VDI 30 Upper turret: X, Z, Y axis Lower turret: X, Z axis Sub-spindle left/right movement: Z3 axis Gbsdpfxoxzq Ncj Anfol C11 spindle: 65 mm diameter (hollow clamping cylinder) C12 spindle: 45 mm diameter (solid clamping cylinder) with part ejector Tool turret type: Sauter 2 x 14 bar high-pressure pumps Accessories: - Complete tool cabinet with toolholders (live and static) as well as carbide inserts and toolholders - Collet chucks for main and sub-spindle - Complete documentation - and more Machine available immediately! Machine ready for operation immediately! Machine will be loaded by us! Transport can be organized upon request!

Stanje: kot nova (razstavni stroj), Leto izdelave: 2025, Special price for our demonstration machine Another unit available immediately (ex works Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of residual wood and pallet offcuts. Pallets must be pre-cut with a jigsaw or chainsaw so that they fit upright into the hopper—see image 2. Ideally, dimensions of approx. 40x20x20 cm allow the wood to lie flat on the ram base, which is the most efficient way for the machine to process it. A hydraulically driven ram at the bottom of the shredder pushes the wood against the rotor, with the pressure adjusted according to load. Material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour (*depending on screen size and material preparation). *Discharge conveyor and overband magnet available at additional cost. + Powerful 18.5 kW motor + Concave blades + Heavy-duty large gearbox + Special load-dependent ram control system Commodity code: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15 pieces, multiple-use (reversible) Option: Double blade row + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutting chamber opening: 630 x 820 mm Fill volume: approx. 0.6 m³ Hydraulically actuated ram Screen perforation as requested (10–30mm) Extraction outlet Ø 160 mm Weight: approx. 1,300 kg (depending on configuration) Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm Moisture content: < 30% oven dry Standard equipment includes: - V-rotor for maximum throughput - Control cabinet with Siemens PLC - Automatic star-delta starter - High-speed hydraulics - Automatic shut-off in case of rotor idle Gbsdpfsdwktksx Anfel - 70–90 rpm for high throughput - Cycle control to avoid idle times - Performance-boosting step control of the hydraulic ram - Pertinax guides for hydraulic ram - Vibration-damping machine feet - CE compliant - MADE IN GERMANY Shredder options: - Raise shredder by 30 cm (preparation for conveyor) + €2,080 net - Angled conveyor belt + €8,770 net Horizontal part: 1200 mm Inclined part: 2500 mm Adjustable angle: 0–60 degrees Discharge height: approx. 2000 mm (+/- 100 mm) - Overband magnet + €5,980 net - Control for conveyor and overband magnet + €2,750 net (Start/stop synchronized with shredder) - Extended hopper + €940 net - Eco rings: + €1,980 net (recommended for more than 15% hardwood content) - Special scraper + €990 net (recommended for veneer or paper) - Double blade row + €995 net Raw material requirements: - Moisture content (oven dry) must be below 30% - Metal or mineral contaminants such as sand, stones, etc., increase wear.

Stanje: kot nova (razstavni stroj), Leto izdelave: 2025, Machine available at a special price Another machine immediately available (ex works Neckartailfingen) * Includes 1-year warranty. Your advantages: + Very robust, straightforward technology + Excellent value for money + Suitable for continuous operation + Long-established, reliable machine Includes control cabinet with timer operation The press is manually activated and then runs until the set time on the timer (e.g., 4 hours) has elapsed. The press then switches off automatically. Technical data: Briquette dimensions: approx. 30 x 30 mm (square) Briquette length: 5-40 mm (material-dependent) Throughput capacity: up to 20 kg/h max. (material-dependent) Machine dimensions approx.: 137 x 75 x 148 cm (L x W x H) Machine weight: approx. 250 kg Silo capacity: approx. 250 litres Motor: 2.2 kW, 400 V - 50 Hz Noise emission: 62 dB Material requirements: - Wood shavings and dust smaller than 15 mm in length Gbjdpfx Asd Nnwlonfol - Moisture content less than 18% ATRO - Sand, stones, metals, and minerals accelerate wear --- Options at extra cost: - Timer function + €490 (net) Machine is started manually and switches off automatically after set time X. - Fill level sensor for automatic operation + €1,450 (net) Press starts and stops automatically * NEW!!! Now available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + €890 (net) (delivery time approx. 8 weeks) - Special pressing units + €2,950 (net) ---

Stanje: novo, Leto izdelave: 2026, Funkcionalnost: popolnoma funkcionalen, We deliver the machines wherever you require, and install them upon request by prior arrangement. Optional: Stainless steel discharge element, stainless steel storage silo, blower, and approximately 3 meters of piping. Grinding mill 800 series, 22 kW or 37 kW 3 x 2 blade set configuration. Bwj3E79Mpn 2 x stators Screen deck as per your request with Variable Frequency Drive, optional Product discharge and storage available in various configurations at highly competitive prices when combined. Motor power can be adjusted. Gjdpfx Aet Iw Hujnfjbl Other modifications are negotiable, such as rotor adaptations (e.g., 5 rows of blades or heavy-duty version). Delivery/timeframe to be coordinated. Please call or email us to discuss or if you have any questions. Kindly respond with your name, company name, and correct phone number. Without this information, RSS Recycling Shredders and Solutions (Netherlands) will not be able to respond.

Stanje: novo, Leto izdelave: 2026, Extremely powerful industrial magnet for iron separation Special price: €990 net (Shipping €14.90 net) Gedpfxetqfhxj Anfobl *Please refer to image 2 for construction lengths The active side features a stainless steel end plate (material 1.4301). Threaded holes are provided on the reverse for mounting *Handle available on request The block magnet systems can be used up to a maximum operating temperature of +100°C. The magnet surface should be cleaned regularly of captured iron parts. Attraction heights for all types, e.g.: For an M5 steel nut approx. 60 mm For an M5 x 30 screw approx. 100 mm Mounting Example 1: Mounted above a conveyor belt, the iron parts "jump" onto the magnetic contact surface. Mounting Example 2: Installed in a pipeline system in direct contact with the material flow. For high separation security, a cascade arrangement of several block magnets in series is possible. Installation and safety instructions: When handling, even during unpacking and later mounting, ensure that no loose iron parts, such as tools or screws, are nearby. The magnetic force is so strong that painful injuries can occur if fingers get caught between iron parts and the active surface. No steel parts should be present within a minimum distance of 400 mm underneath the active surface.