Okenski sistem

WEINIG Unicontrol 6 NC Spindeln

Stanje: rabljeno, Keyway Spindle 1 pc. Number of Milling Units: 5 pcs. Spindle Diameter: 50 mm Control System: Weinig, PC-Nexus #2774 Weinig Unicontrol 6 with NC Spindles Machine is cleaned and fully inspected prior to delivery Technical Data Summary (Please enquire about any additional included accessories) Pos. 1: Cross-Cut Saw ----- > Number of Tools: 1 pc. > Spindle Speed: 2,800 rpm > Spindle Diameter: 40 mm > Max. Tool Diameter: 400 mm > Motor Power: 3 kW > Radial Adjustment pneumatically controlled across 8 positions, e.g., for top edge rounding > Laser Guidance for cutting section detection Pos. 2: Rounding Unit, Horizontal Lower ----- > Position: horizontal, lower > Motor Power: 1.5 kW > Spindle Diameter: 20 mm > Clamping Length: 25 mm > Spindle Speed: 9,000 rpm > Max. Cutting Circle: 130 mm > Axial Adjustment mechanically linked with cross-cut saw > Radial Adjustment pneumatically controlled, on/off NC-Controlled Length Stop ----- > Length: 3,500 mm > Electronic length stop Pos. 3: Tenoning and Keyway Spindle ----- > Number of Tools: variable, stepless adjustment, NC controlled > Tool Clamping Length: 320 mm > Vertical Spindle Stroke: variable, 254 mm, stepless, NC controlled > Spindle Speed: 3,500 rpm > Max. Cutting Circle: 320 mm Djdpevu Hghjfx Afljul > Spindle Diameter: 50 mm > Max. Tool Diameter: 320 mm > Motor Power: 11 kW Pos. 4: 1st Profiling Spindle (Climb and Conventional Milling) ----- > Position: vertical, right > Number of Tools: 1 pc. > Tool Clamping Length: 120 mm > Spindle Speed: 6,000 rpm > Spindle Diameter: 50 mm > Max. Cutting Circle: 232 mm > Motor Power: 7.5 kW Pos. 5: 2nd Profiling Spindle ----- > Position: vertical, right > Number of Tools: variable, stepless adjustment, NC controlled > Tool Clamping Length: 320 mm > Vertical Spindle Stroke: variable, 254 mm, stepless, NC controlled > Spindle Speed: 6,000 rpm > Spindle Diameter: 50 mm > Max. Cutting Circle: 232 mm > Motor Power: 11 kW 2 Feed Rollers opposite the spindle, axially pneumatically controlled, 2 positions Sash Bar Guide consisting of: Guide rail at the stop (climb milling section), Sash bar support rail from above in the area of the vertical right profile milling unit and profiling spindle. Pos. 6: Profiling Milling Unit, Horizontal Upper ----- > Clamping Length: 40 mm > Spindle Diameter: 40 mm > Motor Power: 3.0 kW > Speed: 9,000 rpm > Max. Cutting Circle: 130 mm > Axial Adjustment: 30 mm, 8 positions > Radial Adjustment: 125 mm, 8 positions Pos. 7: 3rd Profiling Spindle (Fitting Spindle) ----- > Position: vertical, right > Tool Clamping Length: 160 mm > Axial Adjustment: 115 mm, 8 positions > Radial Adjustment: 110 mm, 8-position turret > Spindle Speed: 5,850 rpm > Spindle Diameter: 40 mm > Max. Cutting Circle: 210 mm > Motor Power: 3.0 kW Pos. 8: Profile Milling/Grooving Unit, Bottom ----- > Motor Power: 3.0 kW > Tool Clamping Length: 125 mm > ...

Stanje: zelo dobro (rabljeno), Leto izdelave: 1977, Grinding diameter: 350 mm Dedpjunt Eyjfx Aflsul Grinding length: 1000 mm Centre height: 100 mm Grinding wheel diameter: 360 mm Total power requirement: kW Machine weight approx. 3.8 t Space requirement approx. 3.5 x 1.3 x 1.5 m Machine in very good condition! External and internal spindle. Extensive accessories included.

Leto izdelave: 1998, Stanje: dober (rabljeno), I am selling a dowel drilling machine with dowel inserter KOCH Sprint-PTP Dueded Exwgopfx Aflol Year of manufacture: 1998 Number of dowel spindles: 1 Number of insertion heads: 1 Programming CNC-controlled Z-axis Working width: 1200 mm Maximum working height: 36 mm Available for immediate sale

Stanje: rabljeno, Leto izdelave: 1985, Teža: cca 3000 kg Dimenzije: cca 3700 x 2000 x 1600 mm Lokacija skladišča: Nattheim Dujdpfx Aevvi Ttsflel

Stanje: zelo dobro (rabljeno), Leto izdelave: 2012, Set for finger jointing in medium and high volume production. The machine is technically efficient and in good condition. The set includes several tool kits. Features: – Industrial set with a single tenoning machine. Operator-supervised pack loading allows for processing of lower grade raw material, – Process controlled by microprocessors (automatic control), – Rotation of the pack after each cycle on a rotary table (butt joint) or flipping the pack on its back (face jointing for furniture, unique GOMA solution), – Set includes an automatic press loading station, – Possibility of intermediate cutting on the press, TENONER WITH FEED TABLE Specification Values Spindle diameter (milling): 50 x 210 mm Spindle speed: 6,000 rpm Main motor: 18.5 kW Tool dimensions: 250 x 160 mm Saw spindle: for trimming board ends Dusdpfx Afolu D Tfolol Special chipper: 300 x 8 mm Chipper motor: 6 kW / 3,000 rpm Feed table: infinitely variable speed Working width x height: 600 x 30–160 mm Glue nozzle profile: according to tooling FC-10 PZ6/2 PRESS Specification Values Board width: 30–160 mm Board thickness: 20–70 mm Finished board length: 6,000 mm Pressing force: 3 – 7.5 – 10 T Hydraulic power unit: 3 kW / 140 bar

Stanje: zelo dobro (rabljeno), Leto izdelave: 1988, automatic wide belt sander with 2 belts for lacquers, wood, veneer, composites, and various materials Machine can be integrated into a production line Technical specifications: Working width: 1350 mm Maximum usable height: 130 mm Belt size: 2450 x 1350 mm Configuration: 1st Group: Sanding roller diameter 320 mm - grit 60 - blower cleaning belts - 11 kW motor with variator 2nd Group: Sanding roller diameter 320 mm - grit 40 - blower cleaning belts - 11 kW motor with variator Dujdpogmbu Isfx Aflol Scotch Brite - 1.5 kW motor Vacuum table Belt speed variator: 4–19 m/min Operating pressure: 7 bar External dimensions: Machine: 2000 x 2750 x 2200 mm Vacuum pump: 800 x 700 x 900 h mm

Stanje: rabljeno, prevoženi kilometri: 306.127 km, prva registracija: 10/2013, skupna dolžina: 10.600 mm, skupna širina: 2.520 mm, skupna višina: 300 mm, Leto izdelave: 2013, Oprema: ABS, EBS (Elektronski zavorni sistem), elektronski program stabilnosti (ESP), klimatska naprava, nadzor oprijema, servovolan, tempomat, žerjav, - Stability control = Additional options and accessories = - Differential lock = Notes = MB Actros 4146 AK MP3 8x8 crane truck with Fassi 660 loading crane / winch and slewing drive !! SINGLE TIRES !! • All-wheel drive • Fully leaf-sprung • EURO 5 • Telligent 16-speed transmission with clutch pedal • Air conditioning • Reinforced engine brake • Cruise control • Auxiliary heater • Hill start assist • 2 x differential lock • ABS deactivatable • Signal horn • Lamp bar with LED work lights • Rotating beacons Djdpfx Afowmn Tlsloul • Multifunction steering wheel • Radio CD player • Telephone • Tires: 395/85 R20 • Good tire tread! • Unladen weight: 22,544 kg • Gross weight: 32,000 kg (36,000 kg technically possible!) • Trailer coupling – towing eye • Permissible towing capacity: 12,500 kg • 2-line trailer brake system • Overall vehicle length: 10,600 mm Body: FASSI 660 XD Type F600A / 660 AXP 24 • Remote control • 4 hydraulic extensions • Hydraulic slewing head • Hydraulic winch • 4-point stabilizer supports • 10-ton spreader beam • Flatbed body by MÜLLER with drop sides Special equipment: 2-line trailer brake, trailer coupling G 150, trailer socket 24V / 15-pin, brushed steel dashboard, audio system: CD radio (Bluetooth incl. fixed installation for telephone), 220 Ah battery, compressed air horn(s) on cab roof, cab: reinforced shock absorber, cab: moveable entry, cab: comfort suspension (1.8 Hz), construction site vehicle filter, 100 A alternator, fuel tank 400 liters, reinforced clutch, reinforced cooling, PTO MB 10C, programmable special module, rotating beacon left/right, side windows with heat-insulating glass, circuit breaker, seats in cab: comfort driver's seat with air suspension and horizontal suspension, sun visor, roller sunblind for side windows, driver’s and passenger doors, inverter 24V/12V 15A, reinforced stabilizer rear axle, 12 volt socket, front bumper in steel, cross member for trailer coupling, additional heat insulation, auxiliary water heater, gearbox oil cooler Additional features: 2nd steerable front axle, EURO 5 emission standard, axle configuration: 8x8/4, front axle load 9.0 t, trailer coupling: towing coupling, upright exhaust silencer behind cab, mirrors electrically adjustable and heated, steel roof hatch, rear axle differential lock, front axle differential lock, cab version: S (short), suspension leaf/leaf, electric window lifters, 16-speed gearbox, rear axle H 7, 13 t, crown wheel 300, hydraulic pump (Meiller – 6-piston pump), body/chassis for tipper (additional AV), body/chassis: tipper, model update from 06/2008, engine 12.0 ltr – 335 kW V6 diesel (OM 501 LA), engine brake with constant throttle, wheelbase 4800 mm, rear window, Telligent shift system, Telligent braking system with ABS, drum brake front and rear axle, transfer case with differential lock, CB radio preparation, telephone/fax preparation, immobiliser, heat-insulating glass, central locking Cab: single

Stanje: rabljeno, Number of spindles: 6 pcs. Working width: 230 mm Planing height: 120 mm Planer table length: 2500 mm Feed motor: 3 kW Feed speed: 5–24 m/min Total power requirement: 27 kW Dimensions (L/W/H): 3900 x 2200 x 2000 mm Machine weight approx.: 2500 kg Dujdpfxju Su Hus Afljl Weinig Four-Sided Planer Profimat 23, window version with glass bead separation (can also be used as a grooving spindle) ATS control and program control ----- Machine is currently being overhauled and functionally tested Technical data summary (please ask for details on any additional included accessories) General ----- > Working width: 230 mm > Working height: 120 mm > Number of spindles: 6 pcs. > Planer table length: 2500 mm > Feed motor: 3 kW > Feed speed: 5–24 m/min > Total power requirement: 27 kW > Dimensions: 3900 x 2200 x 2000 mm > Machine weight approx.: 2500 kg Spindle configuration ----- > Spindle 1: bottom > Spindle 2: right, pneumatically cycling up/down > Spindle 3: left > Spindle 4: top > Spindle 5: bottom > Spindle 6: glass bead saw, pneumatically cycling up/down Spindle specifications ----- > Spindle 1: 4 kW, 6000 rpm, 40 mm diameter > Spindle 2: 7.5 kW, 6000 rpm, 40 mm diameter > Spindle 3: 6000 rpm, 40 mm diameter > Spindle 4: 5.5 kW, 6000 rpm, 40 mm diameter > Spindle 5: 4 kW, 6000 rpm, 40 mm diameter > Spindle 6: glass bead saw, 2.2 kW, 6000 rpm, 40 mm diameter Other features ----- > Glass bead separation or usable as a grooving device > ATS control: automatic 2-axis positioning for width and height (left and top spindle) with program memory for 99 programs > Machine operation: window package Joint operation of the right spindle and the glass bead discharge via manual selector switch on the control panel > Spindles with mechanical digital readout Option: Used planer heads available (technical data according to manufacturer – subject to prior sale and not guaranteed!)

Stanje: rabljeno, Corner Processing Line Weinig Unicontrol 10 (UC 10) for the production of windows, components, and doors. Suitable for frame-based, series, or single-piece production, featuring 2 tenoning and slotting spindles including Oertli tool set. - Units: 1. Crosscut saw, NC axis, 3 kW, ø 40 mm, 2,800 rpm 2. First tenoning and slotting spindle, NC axis, ø 50 mm, 15 kW, clamping length: 640 mm (8 x 80 mm) 3. Second tenoning and slotting spindle, NC axis, ø 50 mm, 11 kW, clamping length: 400 mm 4. Profiling spindle 1, NC axis, ø 50 mm, 11 kW, clamping length: 4 x 80 mm 5. Profile milling unit, horizontal from above, 3 kW 6. Profiling spindle 2, NC axis, ø 50 mm, 11 kW, clamping length: 4 x 80 mm 7. Profiling spindle 3, NC axis, ø 50 mm, 11 kW, clamping length: 400 mm 8. Profile milling unit, vertical right, 3 kW Duedpfx Afjv Ag Tdelol 9. Profile milling unit, vertical right from above, 3 kW 10. Profile milling unit, horizontal from below, NC axis, 3 kW - Double workpiece package - Profiling rework package with rework carriage - Automatic flipping system - NEXUS PC control - CNC-controlled length stop - Studio window setup - Unit for edge rounding from below with crosscut saw - Georgian bar support rail - Incl. extraction pipe system - Incl. Oertli tool set - Additional technical data and tool drawings available on request.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2006, Funkcionalnost: popolnoma funkcionalen, Popolnoma delujoč UniControl 12, letnik 2006, iz Norveške. - Za natančne tehnične specifikacije prosim odprite priloženi PDF dokument. Prečni prerez UniTec 12: - žagalna enota - rezkar za zaobljanje robov od spodaj - dvigovalno vreteno št. 1 - dvigovalno vreteno št. 2 - dvigovalno vreteno št. 3 Dolga, profilna sekcija UniVar 12: - profilni rezkar - profilni rezkar - profilni rezkar vodoravno - profilni rezkar - profilni rezkar - profilni rezkar Skupna električna moč 114 kW, 400 V AC Potrebna moč odsesavanja 270 m3/min Djdpjmgc I Nefx Afloul Potrebni stisnjen zrak 1000 L/min Stroj je bil v uporabi do 15.08.2023 Plačilo: pred nakladom Dostava: ex tovarna Rendalen - Norveška Stroj se nahaja na Norveškem (v bližini Trondheima) Trenutno je stroj odklopljen, shranjen v suhem in toplem skladišču ter je pripravljen za pošiljanje. Rekman Maskin & Service - servis lesnoobdelovalnih strojev od 1986.