Biesse Techno Logic nakup rabljenega (316)

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, višina obdelovanca (maks.): 90 mm, širina obdelovanca (maks.): 3.200 mm, dolžina obdelovanca (maks.): 3.200 mm, največja debelina roba: 3 mm, The machine has the following configuration: Number of panel sizing/milling units left side: 5 Milling unit (AS10) Double fine millers, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (coarse) Fine trimming for bevel and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 90 mm Panel length max.: 3,200 mm Panel width max.: 3,200 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm EQUIPMENT Conveyor chain with pushers Pressure with rubber belt Panel guiding rails, positioned by NC Edge roll magazine with 6 positions Hot-melt unit for PUR adhesive NORDSON Hnodpsyq Avhjfx Adkoi Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on overhead cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for the installation, securing, and utilization of the machine at the destination. External reference: 7685

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2009, Funkcionalnost: nepreverjeno, število osi: 4, dolžina mize: 4.300 mm, širina mize: 2.200 mm, število vreten: 40, premer orodja: 120 mm, TECHNICAL DETAILS Number of spindles for vertical drilling: 30 Number of spindles for horizontal drilling in X-direction: 6 Hodeyq Ez Tjpfx Adksni Number of spindles for horizontal drilling in Y-direction: 4 Total number of vertical + horizontal spindles: 40 Number of controlled axes: 4 Maximum tool diameter: 120 mm Table dimensions: 4,300 x 2,200 mm Number of positions tool magazine 1: 22 Number of positions tool magazine 2: 8 MACHINE DETAILS Milling motor power: 12 kW Total installed power: 42 kW Control software: BIESSEWORKS EQUIPMENT Automatic panel loading system Automatic panel stacking system Lift table Transport system Vacuum pump Note: The safety fences at the rear and at the loading table are missing and will only be delivered if available. The machine is sold and delivered in its actual and legal condition ("as seen and agreed") based on photo documentation and technical/commercial documentation of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 7087

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2011, Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 6.200 mm, pomik osi Y: 1.935 mm, višina obdelovanca (maks.): 250 mm, število osi: 4, število vreten: 40, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of vertical drilling spindles: 28 Number of horizontal drilling spindles in X direction: 4 Number of horizontal drilling spindles in Y direction: 8 Total number of drilling spindles: 40 Hodpfxsyqzrne Adksni Total number of tool changer positions: 22 Number of suction traverse beams: 10 Milling Unit Number of axes: 4 Motor power: 10.5 kW Automatic tool changer Edge banding unit Gluing unit Tool magazine Grooving unit Number of positions in tool magazine: 22 MACHINE DETAILS Main spindle power: 10.5 kW Total power: 31 kW EQUIPMENT Vacuum pump Safety net Chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8011

Stanje: dober (rabljeno), Koda: 0278 Znamka: COMIL BIESSE Model: COSMO Samonastavljiva spenjalna stiskalnica za pohištvo, opremo, kuhinje, kopalniško pohištvo in različne namene Največja delovna dolžina: 2500 mm Delovna višina: 1200 mm Delovna širina: 700 mm Hitrost pozicioniranja: 3,5 m/min Skupna moč: 3,7 kW Skupne mere: 3760 x 920 x 2280 mm (V) Hedoyuvb Ejpfx Adkeni Teža: 2200 kg

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Koda Ferwood: AGG0062 - Koda proizvajalca: 6314A0111 - Stanje: Rabljeno - Funkcionalnost: Ni testirano - Združljiv stroj: CNC BIESSE ROVER 23/24/27/30/346 - Če ste zainteresirani, nudimo storitev obnove, kontaktirajte nas. Teža in dimenzije za prevoz: 2,5 kg 20x20x20 cm Hnedpfevu Auusx Adkei

Stanje: dober (rabljeno), Koda: 0318 Znamka: BIESSE Model: F 39 E - CE Standard Elektronski večvretenski vrtalni stroj s 39 vreteni za pohištvo, mizarska dela, po meri izdelano pohištvo, panele, kuhinje, kopalniško pohištvo, vrata, okenske okvirje in drugo - CE Standard Hjdpoyrgcbefx Adksni Primeren za horizontalno in vertikalno vrtanje, možno je vsako vmesno vrtanje med 0 in 90° zahvaljujoč zobniškemu motorju in ročnemu kolesu. Elektronski nadzor Tehnični podatki: Število vreten: 39 Hitrost vrtenja vretena: 4000 obr/min Razdalja med vreteni: 32 mm Največja razdalja med središči vrtanja: 1216 mm Globina vrtanja: 65 mm Moč motorja vrtalne glave: 2,3 + 2,3 KM Obratovalni tlak zraka: 6 bar Nameščena električna moč: 4,1 kW Skupne dimenzije (mm): 1800 x 1140 x 1600 h Teža: 700 kg

Stanje: nepreverjeno (rabljeno), Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 3.200 mm, pomik osi Y: 1.300 mm, število vreten: 21, hitro pomikanje X-os: 80 m/min, hitri pomik os Y: 60 m/min, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 3,200 mm Travel range Y-axis: 1,300 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 60 m/min Traverse speed Z-axis: 25 m/min Number of traverses with vacuum suction: 6 Spindles Number of vertical drilling spindles: 15 Number of horizontal drilling spindles in X-direction: 4 Number of horizontal drilling spindles in Y-direction: 2 Total number of spindles: 21 Milling unit Number of axes: 3 Max. speed: 24,000 rpm Motor power: 9 kW Tool changer Number of positions: 10 MACHINE DETAILS Total power requirement: 26 kW EQUIPMENT Vacuum pump WINDOWS control system WRT machine programming software Note: Cones and cutters are not included. Safety fences will be supplied subject to availability (right side missing). The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photographic documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and is solely responsible for installation, securing, and operation of the machine at the destination. External reference: 8174 Hnsdjytr Ryopfx Adkoi

Stanje: rabljeno, BIESSE SAND REGAL 1350 je industrijski širokotrak brusilni stroj, namenjen za kalibracijo in fino brušenje ploščatih kosov v pohištveni in ploščni industriji. Serija REGAL predstavlja robustno proizvodno rešitev, primerno za srednje in velike proizvodne obsege. Hnedpeynb Rfofx Adkoi Stroj je zasnovan modularno in omogoča kombinacijo kalibracijskih ter končnih obdelovalnih operacij v enem prehodu, kar občutno poveča produktivnost.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2018, Funkcionalnost: popolnoma funkcionalen, CNC obdelovalni center Delovno območje X: 3855 mm Delovno območje Y: 1650 mm Delovno območje Z: 245 mm 5-osni elektrovreteno, moč 13 kW, nosilec HSK63F, tekočinsko hlajena Revolverski menjalnik orodij z 12 mesti na vozičku Hsdoyuuw Eopfx Adkjni Menjalnik orodij s 16 mesti na vozičku osi X Glave za vertikalno vrtanje: 20 Glave za horizontalno vrtanje X: 4 Glave za horizontalno vrtanje Y: 4 Rezilo za utore Delovna miza z 8 letvami Programska oprema: bSolid Izmenjevalnik toplote za hladilno tekočino Vakuumska črpalka 250 m3/h Varnostne fotocelice Transportni trak za odrezke Samo 3377 ur delovanja programov z EPS – avtomatsko pozicioniranje letvic in priseskov Vključene priseske in Uniclamps sponke Na voljo julija

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2021, potovalna razdalja osi X: 4.140 mm, pomik osi Y: 1.270 mm, pomik po osi Z: 275 mm, število osi: 5, This 5-axis BIESSE Rover A 1242 was manufactured in 2021. It features a working area of 4140 mm on the X-axis, 1270 mm on the Y-axis, and 275 mm on the Z-axis. The machine is equipped with brushless motors and a PC-based controller for enhanced performance. If you are looking for high-quality CNC woodworking machinery, you should consider the BIESSE Rover A 1242 that we offer for sale. Contact us for further details. • Working Area • Y (5-axis): 1270 mm • Y (4-axis): 1260 mm • Z (with vacuum modules H=74 mm): 230 mm • Z (with H=29 mm vacuum modules): 275 mm • Axes and Drives • X & Y: Rack and pinion drive; accuracy grade 6 • Z: Ball screw with preloaded nut; accuracy grade ISO C7 • Motors: Brushless motors with digital drives via Mechatrolink system • Control System and PC Hardware • Controller: BH660 (PC-based) with WRT (Windows Real Time) technology • CPU: Intel Core i5 or higher • RAM: 16 GB • Storage: 256 GB SSD or higher • Display: 21.5-inch LCD color monitor • Operating system: Windows with real-time process management extension • Connectivity: Ethernet card; USB ports • Electrical and Pneumatic • Power supply: 380 / 400 / 415 V - 50/60 Hz • Control voltage: 24 V DC (stabilized power supply) • Enclosure cooling: Air conditioning system for operation up to 40°C (104°F) • UPS (uninterruptible power supply): 7-10 minutes runtime for data backup • Workpiece Support (ATS system) • Workpiece supports: 8 ATS aluminum beams on linear guides • Module supports: 24 supports (132 × 132 × H41.5 mm) with pneumatic clamping • Set-up assistant (SA): Manual positioning with LED indicators; ±1.5 mm accuracy • Vacuum zones: 2 independent work areas in X; 2 independent clamping areas in X • Software and Licensing • Primary software: NC-HOPS 7 MacroCAM • Safety and Maintenance • Safety system: Bumper system (front and rear) for instant stop in the event of collision • Protection: Transparent polycarbonate front shield and sound-dampening cover • Lubrication: Automatic lubrication system for linear guides and rack/pinion Additional equipment • Vacuum pumps (standard/optional): Up to two units, each 90/100 m³/h or 250 m³/h Hnsdpfx Asyt Rrvsdkoi

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2020, skupna masa: 3.800 kg, Ta 3-osna BIESSE Selco WN 2 je bila izdelana leta 2020. Ima robustno maso stroja 3900 kg in deluje na napetosti 400 VAC s porabo 12 kW. Stroj je zasnovan za učinkovito razrezovanje plošč in ima oznako CE za skladnost. Če iščete visokokakovostno formatno žago, priporočamo, da razmislite o stroju BIESSE Selco WN 2, ki ga prodajamo. Za več informacij nas kontaktirajte. • Teža krmilne omare: 190 kg • Napetost napajanja: 400 VAC • Polni tok: 24 A • Število faz napajanja: 3 • Poraba energije: 12 kW • Frekvenca: 50 Hz Hedpfx Adjyt Rklekjni • Kratkostna vzdržljivost: 10 kA RMS • Dovod stisnjenega zraka: 6,5-7 bar • Zahtevana hitrost odsesavanja: 30 m/s • Oznaka CE: Da

Stanje: rabljeno, Leto izdelave: 2009, BIESSE ARTECH Edge Bander mod. Akron 430 A T - Used Technical Data: - Panel length min/max: 140-3200 mm - Panel width min/max: 85-3200 mm - Panel height min/max: 10-60 mm - Edge thickness (coil) min/max: 0.4-3 mm - Edge thickness (strips) min/max: 0.4-8 mm - Edge height min/max: 14-64 mm - Working height: 900 mm - Panel overhang from feed track: 25 mm - Feed track speed: 12 m/min - Extraction air speed: 30 m/sec - Air supply pressure: 7-10 bar SINTRA LT Control - Infeed guide with mechanical viewer - Pre-milling unit: 2 motors, 1.8 kW, with pad copiers Vertical adjustment of tool position - Gluing unit: glue pot capacity 2 kg 3 pneumatic pressure rollers Hsdpsyt Nvgefx Adksni Digital display for edge thickness - Shear unit with 2 pressure settings depending on edge thickness - Automatic strip edge feeder - End trimming unit: 2 motors, 0.50 kW, pad copier, 2 cutting positions 0°-15°, automatically selectable from the control panel (for increased edge overhang or trimming for best finish) - Multi-function corner rounding unit with 4 selectable positions via control panel Possible operations: flat, chamfer, radius 1, radius 2 For each finishing position, excess edge allowance can be adjusted (+/-) - Edge scraper unit - Glue scraper unit - Program creation for different finishing cycles Machine length: 3880 mm Weight: 1530 kg

Stanje: zelo dobro (rabljeno), Leto izdelave: 2003, Funkcionalnost: popolnoma funkcionalen, Delovna površina 2.893 x 950 mm 6 prečk z 12 priseski Rezkalni vreteno z držalom orodja ISO 30, 3,6 kW, avtomatska vrtalna enota: Hnodpfsymmr Esx Adkoi 10 vertikalnih svedrov 6 horizontalnih svedrov Žaga za utore, Menjalnik orodij s 6 pozicijami. Krmilna enota N500 Barvni zaslon Skupna priključna moč 10 kW 400 V, 50 Hz

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Ferwood koda: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Ni preizkušeno - Združljiv stroj: - Teža: 15KG - Dimenzije: 70X46X34 - V primeru zanimanja nudimo storitev pregleda, kontaktirajte nas. Hedpfx Aeyrqxtodkjni

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Ferwood koda: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Ni preizkušeno - Združljiv stroj: - Teža: 15KG - Dimenzije: 70X46X34 - V primeru zanimanja nudimo storitev pregleda, kontaktirajte nas. Hnedpfx Ajyrqwpedksi

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Ferwood koda: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Ni preizkušeno - Združljiv stroj: - Teža: 15KG - Dimenzije: 70X46X34 - V primeru zanimanja nudimo storitev pregleda, kontaktirajte nas. Hodsyrqv Ejpfx Adkjni

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Ferwood koda: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Ni preizkušeno - Združljiv stroj: - Teža: 15KG - Dimenzije: 70X46X34 - V primeru zanimanja nudimo storitev pregleda, kontaktirajte nas. Hsdpfxjyrqt Re Adkeni

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Koda Ferwood: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Popolnoma delujoče - Združljiv stroj: - Teža: 15 kg - Dimenzije: 70x46x34 - Če ste zainteresirani, nudimo storitev pregleda, kontaktirajte nas. Hnedpeyrqr Hsfx Adkoi

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Koda Ferwood: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Popolnoma delujoče - Združljiv stroj: - Teža: 15 kg - Dimenzije: 70x46x34 - Če ste zainteresirani, nudimo storitev pregleda, kontaktirajte nas. Hnedpfeyrqbbjx Adksi

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Koda Ferwood: RU0009466 - Koda proizvajalca: 03314K00 - Stanje: Rabljeno - Funkcionalnost: Popolnoma delujoče - Združljiv stroj: - Teža: 15 kg - Dimenzije: 70x46x34 - Če ste zainteresirani, nudimo storitev pregleda, kontaktirajte nas. Hnjdpfx Aeyrp U Todkji

Stanje: zelo dobro (rabljeno), Leto izdelave: 2018, Funkcionalnost: popolnoma funkcionalen, Skladišče za shranjevanje in nakladanje plošč Biesse Winstore 3D K1 s kontrolnimi ploščami in transformatorji. Hsdpfx Adjyt Sxdekeni Sistem prijema: Z vakuumskimi priseski, avtomatski na portalu (Gantry) Avtomatsko skladišče za shranjevanje in nakladanje, približno 50x10 m Možnost dodatnega nakupa: Biesse Selco WN6 TwinPusher Na voljo konec leta 2026

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, Funkcionalnost: popolnoma funkcionalen, Delovno območje X: 3060 mm Delovno območje Y: 1260 mm Hnjdpfx Ajytp E Ujdksi Delovno območje Z: 150 mm Elektrovreteno s 3 osmi + možnost 4. osi Rezkalni motor 12 kW z vpenjalom ISO 30 Pripravljeno za delo z agregati 1 agregat ISO 30 z 2 izhodi za horizontalno rezkanje 1 agregat s krožno žago, premer 215 mm Vrtalna glava B21L Revolverski menjalec orodij z 10 pozicijami Delovna miza s 6 prečkami ATS, dolžina 1200 mm 18 podpor, 4 podpori za pomoč pri nakladanju Reakcijska roka vretena Numerično krmiljenje: XP 600, grafični vmesnik Biesse Works Programska oprema: BiesseWorks Advanced Klimatska naprava za elektro omaro 1 vakuumska črpalka 90 m3/h Varnostne preproge Zaščitne mreže 12 priseskov za ozke kose, 12 priseskov 142x136, 6 priseskov 132x75, 6 priseskov 132x54xh48

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2022, Ta panelna žaga BIESSE Selco WNT 630 je bila izdelana leta 2022. Ima maksimalno dolžino reza 3.800 mm, višino izteka žaginega lista 108 mm ter nosilnost dvižne mize 5 ton. Idealna je za obdelavo velikih plošč do mere 3.660 x 2.200 mm. Če iščete kakovosten rezalni stroj, razmislite o nakupu BIESSE Selco WNT 630, ki ga ponujamo v prodajo. Za več informacij nas kontaktirajte. Hnedpfjyf I U Sox Adkoi

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2018, This 4-axis BIESSE Rover S FT 1536 was manufactured in 2018. It features a robust gantry construction, a working area of 3765 × 1560 mm, and a main spindle power of 13.2 kW. It is equipped with an HSK-F63 tool holder system, a 12-position disc-type automatic tool changer, and a BIESSE BH 10 drilling unit offering extensive vertical and horizontal drilling capabilities. Additional features include a grid vacuum table, two 500 m³/h vacuum pumps, and DXF file compatibility. Contact us for more information about this machine. • Weight (kg): 3000 • Main spindle: 1 spindle, 13.2 kW • Axes: 4 • Working area (X × Y): 3765 × 1560 mm • Torque support: 4th axis (C-axis rotation) • Tool holding system: HSK-F63 • Tool change positions: 12 (disc changer) • Tool length measurement: Yes • Drilling unit: Vertical drills: 10, Horizontal drills: 4 (X-direction), 2 (Y-direction) • Grooving saw: In X-direction • Vacuum table: Grid table • Vacuum pumps: 2 × 500 m³/h • Extraction system: Cleaning arm discharge device Hnjdpfxox D Iqvo Adksi • Lubrication: Automatic • Air blast device: Yes • Control system: Interface with DXF file compatibility • CE marked: Yes • Tools, tool holders, aggregates, and mechanical clamps shown in the photos or videos are not included in the scope of delivery.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2007, potovalna razdalja osi X: 4.600 mm, pomik osi Y: 1.935 mm, pomik po osi Z: 275 mm, število osi: 5, This 5-axis Biesse Rover C9.50 was manufactured in 2007. It features a large working area (X = 4600 mm, Y = 1935 mm, Z = 275 mm), an automatic lubrication system, and a control unit for 5-axis interpolation. The machine is equipped with a vacuum system, a chip conveyor belt, and liquid cooling. If you are looking for high-quality CNC machining capabilities, you should consider the Biesse Rover C9.50 machine we offer for sale. Contact us for more information. Working Table and Clamping • 8 ATS panel supports (L = 1525 mm) and 24 sliding rails • Automatic positioning of panel supports and sliding rails (EPS X-Y) • Pneumatic locking system, divided into 2 working zones in X • 8 rear reference stops, stroke 115 mm • 8 stops with 140 mm stroke, positioned at 1175 mm (L = 1280 / 1525 / 1800 mm) • 8 stops with 140 mm stroke, positioned at 770 mm (L = 1280 / 1525 / 1800 mm) • 4 side stops, 140 mm stroke (2 left + 2 right), pneumatic system • 4 removable center stops, 140 mm stroke (2 left + 2 right), with pneumatic system • Sensor for detecting lowered stops • Pneumatic system for lifting support bars • 6 lifting support bars for easy loading (H = 74 mm modules) Vacuum • Vacuum system for a 250 m3/h pump • 250 m3/h rotary vane vacuum pump for the standard vacuum system Processing Units and Configuration Hodpfx Adsx D H Hcokoni • C3-A1 configuration: • Device for fitting chip deflectors with pneumatic or inductive sensors on a 5-axis machining unit • Flange for fitting units on a machining group with 5 interpolating axes (units can only be used when the electric spindle is vertical) • C3-P2 configuration: • Additional Z-carriage for rear machining units, controlled by an independent Z-axis • BH 42 L drilling head • Chain tool changer with 22 positions (180 mm center-to-center) • Iron gripper for chip deflector with pneumatic or inductive sensor, positioned in the chain tool changer • RH chip deflector with inductive sensor for standard electrospindle or 15 kW 5-axis electrospindle (requires chip deflector device; requires flange for mounting units when using a 5-axis electrospindle; requires C-axis when using a standard electrospindle) Systems • Automatic lubrication system • Control unit with 5 interpolating axes Additional Equipment • Conveyor belt for removal of chips and scrap parts (chip conveyor) • Liquid cooling unit for liquid-cooled systems (can cool two electrospindles or one electrospindle plus one liquid-cooled drilling head) Note: The technical data and descriptions are taken from the original order confirmation and are for informational purposes only; they are not binding.