Brian James Trailers Nizki Nakladalnik nakup rabljenega (14.337)

Stanje: novo, številka stroja/vozila: b50cac2c60a813b0968994fa0, lastna masa: 5.700 kg, največja dovoljena obremenitev: 18.300 kg, skupna masa: 24.000 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Full-width rear mudflap Preparation for widening to 3,000 mm (holes in outer frame, not in rear bevel) Low-loader lashing rings 1 pair of lashing cutouts embedded in the front longitudinal beam at the gooseneck, each rated for 10 t 7 pairs of lashing mushroom pins embedded on top and side of the outer frame, each rated for 10 t 1 x on the front gooseneck 5 x in the low-bed area 1 x in the rear bevel 12 pairs of lashing holes in the outer frame, each rated for 5 t (for lashing strap hooks) 5 x at the gooseneck, 6 x in the low-bed area, and 1 x in the rear bevel Drawbar system for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles, brand as per manufacturer’s choice Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 unmistakable coupling heads at the front, with connecting lines to the truck, Connecting lines extended by approx. 60 cm No ABS, but with mechanical ALB (automatic load-dependent brake valve), thus maximum 60 km/h permit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 7-pin 12 Volt plug at the front with connecting cable, extended by approx. 60 cm 1 LED beacon with holder, operated via parking light (lamp removable) 2 pairs of illuminated and extendable warning plates up to 3,000 mm Floor Front gooseneck with steel/chequer plate covering Ijdpfxoi Ri Ago Agtsat Toolbox recessed in the drive-over slant to gooseneck Following area with 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-bed loading area including rear bevel: 5,900 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wooden covering Spring-assisted lifting Operating Instructions For axle loads of 10,000 kg, an exemption permit is required; only indivisible loads permitted!!! The stated total weight is technically possible; depending on the load, the total weight may not be achievable within the allowable axle/support and fifth wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate for max. 60 km/h approval, towing vehicle as agricultural/forestry vehicle (LoF), (for Switzerland, max. 40 km/h possible) Prepared for double-line license plate holder No contour markings / reflective tape according to ECE R 048 Painting Frame: DB 7350 Novagrau 10-year corrosion protection warranty Drawbar galvanized or black, according to manufacturer’s choice Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 15431365fe5515297a6a9fb05, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball-bearing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mud flaps Half-shell mudguards on 1st and 2nd axles with antispray mud flaps behind each axle, antispray mud flaps before and after 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points each 5 t located in the excavator arm recess on the side at the main frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf insert, W=620/H=360/D=440 mm, can be locked with a padlock (lock not included) 1 storage box recessed into the floor at the gooseneck, with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm 70 mm timber planks for extension to 3,000 mm Storage compartment for timber planks under the loading platform Lashing eyes (40 securing options) 1 pair lashing eyes on gooseneck, each 5 t 9 pairs lashing mushrooms integrated on top and side of outer frame, each 10 t 2 x on gooseneck to the front 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each 5 t (for tension belt attachment) 3 pairs of additional folding lashing eyes, each 10 t 1 x inside next to the main frame at the beginning of the low-bed 1 x on gooseneck (protruding) 1 x recessed behind the last axle Trailer towing device turntable Drawbar with tested 50 mm towing eye, towing eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum braked axles Parabolic spring suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) front and rear Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 Volt, multi-chamber lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable 1 LED beacon with holder, operated via sidelights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel chequer plate covering Followed by 70 mm softwood floor, wheel arch area with steel chequer plate Rear bevel with 70 mm softwood floor Loading ramps Isdpei Ri A Ssfx Agtoat Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber overlay Spring-assisted lifting Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for double-line licence plate holder Conspicuity marking with reflective strips according to ECE R 048, white at the side and red at the rear Warning panel according to ECE - 70 Coating Frame hot-dip galvanized incl. passivation, 15-year corrosion guarantee Drawbar galvanized or black, as per the manufacturer's choice Loading ramps hot-dip galvanized Attention! Archive pictures shown!

Stanje: novo, številka stroja/vozila: d461243f559015adca5bb372c, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflap Half-shell mudguards on 1st axle with anti-spray mudflaps Anti-spray mudflaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: W=620/H=360/D=440 mm, lockable with a padlock Extendable width up to 3,000 mm Central storage compartment for timber planks on loading area 70 mm timber planks for widening to 3,000 mm Lashing rings for low-bed (40 lashing points) 1 pair of lashing apertures recessed in the front longitudinal beam at the gooseneck, each rated for 10 t 4 pairs of lashing holes in the external frame, each rated for 5 t (for lashing strap hooks) 7 pairs of lashing mushrooms embedded on top and side of the outer frame, each rated for 10 t 1 at the front on the gooseneck 6 in the low-bed section First lashing ring 250 mm from the front, last max. 250 mm from the rear, spacing between lashing rings not greater than 1,100 mm 5 pairs of stake pockets embedded in the external frame, internal dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes) 2 pairs of additional folding lashing eyes, each rated for 10 t 1 on the gooseneck (protruding) 1 recessed behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 40 mm towing eye Axles + Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and tyres 235/75 R 17.5 Manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line pneumatic braking system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connecting lines to towing vehicle ABS and ALB, ABS connector at the front with connecting cable Brand: Wabco, Knorr or Haldex Electrics 24 Volt, multi-chamber rear lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with bracket, controlled via parking lights (removable beacon) 2 pairs of warning boards, double, LED illuminated, extendable to 3,000 mm Floor Gooseneck front with steel tread plate covering Storage box recessed in the transition to the gooseneck Followed by 70 mm softwood flooring, wheel arch areas with steel tread plate covering Rear chamfer with 70 mm softwood flooring Iasdpsi Ri Dlefx Agtjt Low-bed area incl. rear chamfer: 6,500 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber-layered Hydraulically operated via tractor PTO with throttle, operated from left-hand side, front Hydraulic connection with SVK coupling NW 10/3, including connecting hose Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Warning board according to ECE - 70 Paintwork Frame hot-dip galvanized incl. passivation 15-year warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Note: These are archive images!

Stanje: novo, številka stroja/vozila: dd98a7658922be8f2e25bcadb, lastna masa: 2 kg, največja dovoljena obremenitev: 8 kg, skupna masa: 10 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235/75 r 17,5, Further information Chassis Central Axle Trailer Low-bed Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support 2 wheel chocks with holders Steel mudguards over both wheels Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 250 mm Axles & Suspension Euro-axles (manufacturer’s choice), with tapered roller bearings and S-cam brakes Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 (manufacturer’s choice) Factory silver steel rims Braking System 2-line compressed air braking system Spring-loaded parking brake 2 mistake-proof coupling heads at the front, with connection lines to the towing vehicle, ABS and ALB, with ABS plug at the front, including connection cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white marker lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin mistake-proof plugs at the front, including connection cable Iaodpfei Ri Ebox Agtst Body TTS Low-mounted steel trough, bridge floor made of steel/chequer plate covering, steel sidewalls solidly welded to the floor Bridge length 4500 mm; trough at the front and sides with load-lock profile for attaching lashing straps (8 points in front, 12 per side) Note: Slight floor waviness possible due to welding distortion! 2 pairs of lashing rings, one at the corners of the steel trough front and one at the rear floor, each rated 5t 2 additional pairs of lashing rings in the floor, each rated 5t Ramps Steel ramps, 2300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps Wooden covering Gas spring assist for one-man operation Operating instructions The stated gross weight is technically possible; depending on the load, the gross weight may not be achievable while observing the permissible axle/load and saddle loads. (Poor driving and tracking performance possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Outline markings with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame RAL 3002 Carmine red Ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: a3b1347da4aa7f31dceb875db, lastna masa: 2 kg, največja dovoljena obremenitev: 9 kg, skupna masa: 11 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Central Axle Trailer Fine-grained steel welded construction 6 pairs of lashing eyes bolted to the outer floor/frame, each rated at 5 tons Gear support leg at the front Foldable rear support 2 wheel chocks with holder Steel underrun protection Full-width rear mudflap Quarter-shell fenders Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & Suspension BPW drum brake axles Axles/chassis laser-measured for reduced tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Factory silver steel rims Braking System Dual-line air brake system Hand spindle parking brake Integral air reservoir 2 interchange-proof coupling heads at the front with connecting pipes to the towing vehicle ABS and ALB, ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side markers 2 white front position lights 2 white/red rear marker lights 2 x 7-pin interchange-proof plugs at the front, with connecting cable Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness possible due to welding distortion! Iedpfx Agei Ri Ilsteat Platform length approx. 5,200 mm Rear tapering approx. 900 mm Front wall / corner posts 25 mm aluminum hollow profile, 320 mm high Side walls 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / corner posts 1 pair of steel stanchions fixed to the frame and with holders for securing the loading ramps, entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps wooden inlay with gas strut for one-person operation Operating Instructions The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable within the permitted axle/support/coupling loads. (Poor driving and tracking may result from incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau, 10-year warranty against rust-through Front wall aluminum Side wall anodized aluminum Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 628cde0fe99cc2d3c8eaa8dd8, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear spray flap Half-shell mudguards on 1st axle with anti-spray flaps, anti-spray flaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: width=620 mm / height=360 mm / depth=440 mm, lockable with padlock (padlock not included) Extendable width up to 3,000 mm Storage compartment for wooden planks in the centre of the loading area 70 mm wooden planks for extension to 3,000 mm Tie-down lugs for low loader (40 lashing points) 1 pair of lashing cut-outs in the longitudinal beam at the front, recessed into the gooseneck, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for securing with lashing straps) 7 pairs of lashing mushrooms, recessed at the top and side of the outer frame, each rated at 10 t 1 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front, last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, interior dimensions 70 x 40 mm (convertible to 5 t ring lashing points, not included) 2 additional pairs of folding lashing rings, each rated at 10 t 1 on the gooseneck (protruding) 1 behind the last axle, recessed in the floor Towing Device Turntable Trailer Drawbar with certified 40 mm towing eye Axles and Suspension Drum brake axles, manufacturer’s choice Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalisation (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims, twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front with connecting lines to the tractor unit ABS and ALB, with ABS socket at the front and connecting cable Manufacturer: Wabco or Knorr Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with bracket, switched with parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/chequer plate covering Toolbox recessed into transition slope to gooseneck Following area with 70 mm softwood floor, steel/chequer plate in wheel arch area Iodpfei Ri Ddsx Agtoat Rear taper with 70 mm softwood floor Low-loader deck including rear taper: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber surfaced With spring lift assistance Country of Registration / License Plates Country of registration: Germany 24/7-Service Hotline Prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on sides, red at rear Warning sign according to ECE-70 Painting Frame hot-dip galvanized including passivation 15 years’ warranty against corrosion perforation Drawbar galvanized or black, manufacturer’s choice Loading ramps hot-dip galvanized Attention! Archive images shown!

Stanje: novo, številka stroja/vozila: 55d3c5c03e032385649769b1b, lastna masa: 9.900 kg, največja dovoljena obremenitev: 14.100 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with heavy-duty slewing ring, integrated storage box incl. Turntable front structure Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Extendable widenings to 3,000 mm (not at rear taper) (track width of the machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central compartment on loading area for timber planks 70 mm timber planks for widening to 3,000 mm Lashing points Low-loader 3 pairs of integrated lashing points, each rated to 10 t, at the front floor 6 pairs of mushroom lashing points, top and side integrated in outer frame, each 10 t 1 x at neck area remaining points distributed, distance no greater than 1,200 mm 1 x at rear taper 5 pairs of stake pockets integrated in the outer frame, internal size 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly for trailer turntable Drawbar with certified 40 mm towing eye Note: For 40 mm towing eye, the maximum permissible gross weight of the towing vehicle is 18,000 kg. Otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Steel twin wheels, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the truck ABS and ALB, with ABS connector at front, connection cable included Attention: The trailer may only be towed by vehicles that ensure ABS functionality! Electrics 24-volt multi-chamber lights, side yellow LED lighting 2 white front position lights 2 white/red rear lane marker lights 2 x 7-pin non-interchangeable connectors at the front, with connection cable 1 LED beacon with bracket, operated via parking lights (removable beacon) 2 pairs of warning boards, double LED-lit and extendable to 3,000 mm Floor Steel floor at front section thereafter 70 mm softwood floor, in wheel arch area with steel/chequer plate covering Rear taper with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable wooden inlays spring-assisted lifting Operating instructions Exception permit required for 10,000 kg axle load, only indivisible loads allowed!!! The specified total weight is technically possible. Depending on the cargo, the full gross weight may not be achieved while observing permissible axle/pin/support loads (poor tracking and handling may result from incorrect load distribution) Country of Registration / Plates Registration country: Germany 1 with Dekra inspection and report (according to §13 EC-FGV) 24/7 service hotline prepared for 2-line license plate holder Conspicuity markings with reflective strips acc. ECE R 048, white on the sides, red at the rear Paint Frame RAL 3002 Carmine Red 10 years warranty against rust-through Iaedpfxji Ri I Eo Agtet Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Attention: Archive photos!

Stanje: novo, številka stroja/vozila: 6d88bda3a1ee2464a81b34f36, lastna masa: 4 kg, največja dovoljena obremenitev: 13 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction with a slight central camber, turntable with heavy-duty ball bearing slewing ring, chocks with holders, quarter shell mudguards in front of and behind each axle. Lashing Points Low Loader Over front axle: 2 pairs of ring lashing eyes (each 5 t) at the front on the cranked section Low-bed: 4 pairs of lashing eyes (each 6 t) at the sides of the lowbed 5 pairs of lashing eyes (each 5 t) between the longitudinal beams Drawbar Assembly Turntable Trailer Drawbar with certified 40 mm towing eye, mechanically adjustable in length by 6 x 100 mm increments and lockable (Drawbar length 1,700 – 2,300 mm) Axles + Suspension BPW drum brake axles with 10 t axle load each, slack adjusters. Continuous axle brake test up to 105 km/h. Rear axle can be removed manually. To do so, release air locking mechanism, lower the rear section to the ground, disconnect hydraulic hoses from rear section, insert the transport bar into a rear socket, and by gently pushing down and simultaneously pulling backwards, release rear section (parking brake released). After loading/unloading, move rear section into position and hook up to mark. Then raise rear section to driving height and connect hydraulic hoses. Confirm bolt locking (visual inspection if bolt snaps in) and check rear function. Air suspension with lift & lower valve. Wheels and Tires 235/75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver. Braking System 2-line compressed air brake system, spring-loaded parking brake, 2 fool-proof coupling heads at front with connection lines to tractor, EBS, electronic brake system with EBS plug at front with connection cable. Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Ijdpfx Agji Ri N Aetoat Electrics 24 volt, multi-chamber lights, yellow LED side marker lights, 2 white position lights front, 2 white/red lane control lights rear, revolving beacon with bracket, powered via parking light (removable), 2 pairs of warning boards double LED illuminated and extendable up to 3,300 mm, removable with plug, 2 x 7-pin fool-proof plugs at front with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (for electrics only, not for ABS/EBS) Floor Steel/aluminum checker plate floor on cranked section, between longitudinal and cross beams with perforated cover plates. Axle cover not drive-over, widening to 3,000 or 3,300 mm possible. Operating Instructions Note! For 10,000 kg axle load, a special permit is required. Permit must be applied for separately in each federal state; the legislator is not obliged to grant approval for 20 t GVW. Customer’s risk. Special permit required if total train length exceeds 18,750 mm. Observe country-specific registration regulations. The stated gross weight is technically possible; depending on the cargo, the gross weight may not be achievable in compliance with permissible axle, support, and fifth wheel loads. Observe BO-circle!!! Registration / License Plates Registration country: Germany, with Dekra inspection and report (per §13 EC-FGV), prepared for single-line license plate holder, ECE-70-compliant warning board, contour marking with reflective strips per ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL black Attention: Archive images!

Stanje: novo, številka stroja/vozila: f8fb99947a1c19bc4d63549ff, lastna masa: 6 kg, največja dovoljena obremenitev: 17 kg, skupna masa: 24 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Rear foldable support 2 wheel chocks with holders Side underrun protection in aluminium Full-width rear mudflap Half-shell mudguards on the 1st axle with anti-spray mudflaps; anti-spray mudflaps behind 2nd and 3rd axles 1 plastic toolbox with shelf, dimensions: width 620 mm, height 360 mm, depth 440 mm, lockable with padlock (padlock not included) Extendable width up to 3,000 mm (not at rear slope) (track width of machines or vehicles to be transported must not exceed external frame width of 2,550 mm) Central storage compartment for timber planks on the loading platform 70 mm timber planks for widening to 3,000 mm Tie-down eyes for low-loader: 1 pair of flush-mounted ring lashing eyes at the front on the swan neck, each rated at 5t 7 pairs of lashing mushroom pins, recessed on top and sides of outer frame, each rated at 10t 1x front on swan neck 6x in low bed area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not more than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (convertible to 5t ring lashing eyes, not included) 2 additional pairs of foldable lashing eyes, each rated at 10t 1x on swan neck (protruding) 1x behind the last axle, recessed in the floor Drawbar assembly for turntable trailer: Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tyre wear and fuel consumption Iajdpfoi Riwfsx Agtet Parabolic springs with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker compensation) Wheels and Tyres 235/75 R 17.5 Manufacturer's choice, with M&S marking Steel rims in twin arrangement, factory silver finish Braking System 2-line compressed air braking system Spring-actuated parking brake 2 foolproof coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS socket at the front and connecting cable Brand: Wabco or Knorr Note: The trailer may only be towed by vehicles that ensure the proper functioning of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front 2 white/red lane departure lights at the rear 2x 7-pin foolproof plugs at the front with connecting cable 1 LED beacon with bracket, switched via parking lights (lamp removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Floor Front swan neck with steel chequer plate covering Storage box recessed in the approach slope to the swan neck Then 70 mm softwood flooring, in wheel arch area with steel chequer plate Rear slope with 70 mm softwood flooring Low-bed area incl. rear slope 6,500 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety device, foldable at the bottom (prevents lateral displacement of ramps, not in combination with laterally hydraulic ramp adjustment) Wooden covering Spring-assisted lifting support Operating Instructions At 10,000 kg axle load, a special permit is required, only indivisible loads allowed! The specified total weight is technically possible, but depending on the cargo, the total weight may not be achievable while complying with the permissible axle, support, and king pin loads (poor handling or tracking may result from incorrect load distribution) Country of Registration / Pla

Stanje: novo, številka stroja/vozila: f79a9f15e7131d57a512793ab, lastna masa: 8.900 kg, največja dovoljena obremenitev: 15.100 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear supports 2 wheel chocks with holders Side underrun protection, aluminium Rear spray guards across the full width Quarter fender before 1st axle Extendable outriggers up to 3,000 mm (not in the rear slope area) (Note: The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central storage compartment for timber planks on the loading area 70 mm timber planks for extension to 3,000 mm Lashing points Low-bed 1 pair of lashing rings on gooseneck, each rated at 5 t 9 pairs of lashing mushrooms, flush-mounted on the top and side in the outer frame, each rated at 10 t 2 x front on gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated at 5 t (for attaching tie-down straps) Drawbar System Turntable trailer Ijdpfxji Ri Izo Agtsat Drawbar with certified 50 mm towing eye Axles & Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mount and mechanical axle load compensation (rocker balance) front and rear Wheels and Tyres 235/75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 swap-proof coupling heads at the front with connection lines to towing vehicle ABS and ALS, with ABS connector at the front and connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, side amber LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 1 LED beacon with holder, switchable by parking light (removable) 2 pairs of warning boards, double LED illuminated and extendable up to 3,000 mm 2 x 7-pin swap-proof plugs at the front, with connecting cable Floor Gooseneck at front with steel/chequer plate covering Thereafter 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear slope with 70 mm softwood floor Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood plated Hydraulic activation via auxiliary drive on tractor unit with throttle, operation on front left side Hydraulic connection with SVK connector NW 10/3, including connection hose Operating Instructions A special permit is required for an axle load of 10,000 kg; only indivisible loads possible!!! The specified gross weight is technically possible; depending on the freight, the permissible gross weight may not be achieved while respecting axle, support and kingpin loads. (Poor driving and trailing behaviour possible due to incorrect load distribution) Registration Country / Plates Country of registration: Germany With Dekra inspection and report (according to §13 EC-FGV) 24/7 Service Hotline Included Prepared for double-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides, red at rear Paintwork Frame DB 7350 Nova Grey 10-year warranty against rust-through Drawbar galvanised or black, at manufacturer’s choice Access ramps hot-dip galvanised

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake Isdpfx Ajlpav Uogteat * 4 axles * Wheelbase 6,500 mm * Hydraulic ramp length 2,850 mm – width 650 mm * Loading edge height 920 mm * Extendable to 3 m Subject to errors and omissions

Stanje: novo, konfiguracija osi: 2 osi, Leto izdelave: 2020, Payload: 12,000 kg Ijdpfxoytdbwo Agtjat

Stanje: novo, Leto izdelave: 2025, Mac 16 premium nakladalna prikolica Iajdpfjytdbqex Agtot    • Hitrovozne osi (10 ton na os)    • Zračne zavore (Wabco EBS + ACR)    • Dvojne pnevmatike 235/75/17.5    • Hidravlične nakladalne rampe    • Ravna tla 4900 x 2550 mm    • Poševna tla 1500 x 2550 mm    • Vlečna kljuka 50 mm, višina 520 mm    • Hidravlična podpora    • LED osvetlitev    • Shranjevalna škatla    • COC dokumenti    • Registracija tablic Stanje: Novo Leto izdelave: 2025

Stanje: novo, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.800 mm, širina tovornega prostora: 2.550 mm, barva: rdeča, Leto izdelave: 2025, Payload: 15,000 kg Ijdpfx Aoytdbksgtsat

Stanje: rabljeno, DDV/obdavčitev razlike: DDV je odbitna Isdoytc Uiepfx Agtjat

Stanje: novo, konfiguracija osi: 2 osi, barva: srebrn, AGM pocinkovani (pol-) nizkopralniki se lahko sestavijo po meri stranke, da se za vsako stranko ponudi primeren (pol-) nizkopralnik. Standardne dimenzije: 2,1 metra širine, 4 do 11 metrov dolžine. Nosilnost do 25 ton. Število osi je odvisno od dolžine in nosilnosti. Iasdpfjytc S Ijx Agtot Različne možnosti: - Nakladalna površina iz rebraste pločevine ali trdega lesa - Vzmetena trikotna ojnica, nastavljiva po višini, po potrebi z oporno nogo ali podporno kolo - Obodno široko osvetlitev - Zaščitene luči - Pritrdilne ušesca okrog nalagalne površine - Posamične ali fiksne nakladalne rampe, po želji hidravlično in nastavljive po širini - Nagnjen zadnji del, nagnjen "vrat" na sprednjem delu nizkopralnika - Skladiščni predali pod nalagalno površino - Vrtljivi obroč s trikotnikom ali fiksna ojnica - Tovorne ali kmetijske pnevmatike Stanje: Novo

Stanje: novo, konfiguracija osi: 2 osi, Leto izdelave: 2021, Oprema: ABS, Technical Data for EBERT TLS 43 ATV Special Low Loader: Permissible fifth-wheel load: 19,000 kg; Permissible axle load: 24,000 kg; Gross vehicle weight: 43,000 kg; Unladen weight (DIN approx.): 12,500 kg; Low-bed length (internal): approx. 6,650 mm + 4,000 mm; Axle table length: 2,700 mm; Overall width: 2,550 mm; Loading height/low bed: approx. 200 mm – 350 mm; Sliding table length: 500 mm; Low-bed width extension to: 3,050 mm; Low-bed telescoping by: 4,000 mm; B-dimension: 12,000 mm; Entire vehicle flame-spray galvanized, with epoxy primer and 2K finish; Oversize warning signs front and rear with red/white panels. Wheels: 9 x Michelin 245 / 70 R 17.5 X MULTI T VB 143J/146F Steering: TRIDEC DLS with Tritronic Axles: 12,000 kg – DLS independent wheel suspension, hydraulic steering and suspension Front raised platform: - Doors in the corners left and right, accessible from outside - Storage box with lid behind the bulkhead, height 600mm, width 2,480 mm, depth 7,500 mm - Spare wheel on the raised platform, right behind the partition - Staircase on the right side for access from low bed to front raised platform - Hydraulic coupling for decoupling on left side – 6-way Multi-Faster coupling - 6 lashing points 3,000 kg spec. outside on the raised platform (recessed lashing rings) - 2 lashing points 5,000 kg spec. on top of the longitudinal beams (rearward) Low bed: - Climbing aids at the boom – extendable - Low bed telescopic by 4,000 mm, lockable every 500 mm - With sliding table, lockable every 250 mm - 28 lashing points 10,000 kg spec. outside in external frame - 24 stake sleeves 90x90 mm, evenly distributed for low-bed extension to 3,050 mm - 50 mm hardwood planks placed between extension tubes, 10 mm projection Rear raised platform: - Front end angled and perforated, for retrofitting ramps, galvanized through adapters - Ramp intake profiles (Altec) – C rails at the rear - 6 lashing points 10,000 kg spec. outside on rear raised platform - 6 lashing points 5,000 kg spec. in excavator well - 8 lashing points 5,000 kg spec. for oversize loads on external frame - Closure of excavator well front and rear with wooden floorboard (insertable) Electrics: - Use NATO coiled cable, power supplied by towing vehicle - Rotating beacon central at rear - Side marker lights in LED design - Standard upright rear light assembly (LC5) - Work lamp on raised platform for illuminating low bed - Decoupling: safety sensor and pressure switch for suspension Air: - Aluminium air tanks 60 l (2x 10 l, 2x 20 l) - TEBS modulator - Extension locks left and right (valve on side of rear raised platform) - Double-release valve Hydraulics: - Hydraulic system on raised platform for steering, suspension, and detachable gooseneck Iasdeyfvwbjpfx Agtst Accessories: - 2 sets of 4 wooden planks as supports for low-bed extension and sliding table - 2 chocks for decoupling - 4 wheel chocks Upon request, we can provide you with a leasing or financing offer from Mercedes-Benz Bank. Mr. Ebert (Tel. ...) will be happy to assist you. Further information available on our website. Subject to errors and prior sale! New TÜV, Rental possible GVW: 43,000 kg Contact Tobias Ebert for further information.

Stanje: rabljeno, Leto izdelave: 2006, Oprema: ABS, Goldhofer STZ-H6-57/80A Telescopic Low Loader for Wagon Transport Approval                    Technical 1 Speed:                80 km/h                65 km/h Fifth Wheel Load:      23,000 kg           26,000 kg Rear Axle Load:        10,000 kg           11,000 kg Gross Weight:          83,000 kg           92,000 kg Payload:                52,500 kg           61,500 kg Unladen Weight (without equipment): 30,500 kg Gooseneck: Length: 4,000 mm Width: 2,480 mm Construction Height: 235 mm Coupling Height: 1,350 mm Front DLR: 1,420 mm Rear DLR: 2,700 mm King pin: 3.5 inches Chamfer: 10 degrees Front Corners: Beveled 45 degrees Flooring: Spruce 50 mm Landing Legs: Mechanical Width with side walls: 2,550 mm Hydraulic STZ gooseneck with external beams, hydraulically liftable and lowerable With mechanical drop tube supports and hydraulic support cylinders Hydromechanical forced steering (2-circuit steering) in a flat design (construction height 235 mm) with adjustable guide elements and THP steering cylinders. Loading Platform: Type: Platform Liftable: No Length: 13,000 mm Width: 3,000 mm Flooring: Sheet/Spruce 50 mm Wheel recesses: No Extensions: No Extendable: Single-telescopic Length 1: 10,000 mm Loading Heights (laden): Loading height 1: 815 mm Loading platform extendable, implemented as an outer and inner tube construction, with a fixed platform section at the front, 1,070 mm long. Integrated pin-eye coupling in the fixed platform section for coupling deck bridge extension beams; our welded Vkt. rails serve as running rails for track gauges 1,000 mm (track width 1,015 mm) and 1,435 mm (track width 1,450 mm). Locking of the extension stages by spring-loaded cylinders and conical sleeves Platform height at the center frame tube (outer tube) approx. 815 mm (+/- 130 mm) Platform height at the embedded rail elements approx. 790 mm (+/- 130 mm) Rear Undercarriage: Chassis Type: Standard Loaded loading height: 815 mm Width: 3,000 mm Wheelbase: 1,360 mm Flooring: Sheet Extensions: No Wheel recesses: No Excavator recess: No Axles: Number of axles: 6 Lift axle: see accessories Axle type: Drop-arm stub axle Axle equalization: Hydraulic Axle make: BPW/Eco Operating positions: 1 Axle lift (1) +/-: 130/130 mm Axle lift (2) +/-: 0/0 mm Raise/lower valve: Yes 1st axle can be pneumatically lifted with lift airbag Steering: Number of steering axles: 6 Steering axle arrangement: all steered Max steering angle: 45° Steering type: Hydr. 2-circuit Tyres: Iedpfxjyfvf So Agtsat Dimension: 235/75 R 17.5 143/141 J Tyre type: Twin Rim type: Disc Hub centering: Centered Brake Code: Compliant with EU regulations: Yes AGS: Yes ALB: Yes ABS: Yes With ABS del: No Parking brake: Spring-applied EBS: No ECAS: No Note: Brake calculation No.: GH 4324S Chassis Note: Steering designed for the extended mode with greater steering angle of the front axles Open wheel cutouts above the wheels with narrow cross members between (ALU covers see accessories) Control elements protected on the left in the direction of travel...

Stanje: novo, konfiguracija osi: 3 osi, Leto izdelave: 2022, Oprema: ABS, Technical specifications for EBERT TLS 43 ATV Special Low Loader: - Permissible kingpin load: 19,000 kg - Permissible axle load: 36,000 kg - Permissible gross weight: 55,000 kg - Unladen weight (DIN): approx. 15,500 kg - Low-bed loading length (internal): approx. 6,650 mm + 4,000 mm - Axle table length: 3,550 mm - External width: 2,550 mm - Loading edge/low-bed height: approx. 200 mm - 350 mm, sliding table length: 500 mm - Low-bed width extension to: 3,050 mm - Low-bed telescoping extension: 4,000 mm - B-dimension: 13,300 mm - Entire vehicle flame-sprayed galvanized, with epoxy primer and 2K paint finish - Oversize load signage at front and rear with red/white warning boards Iaedpfx Ageyfu N Aetot Wheels: - 13 x Michelin 245 / 70 R 17.5 X MULTI T VB 143J/146F Steering: - TRIDEC DLS with Tritronic Axles: - 12,000 kg – DLS single wheel suspension, hydraulically steered and hydraulically suspended Front high-bed: - Side walls 600 mm high - Angled front corners at the high-bed - Doors in the front corners accessible from the outside - Lockable storage box with lid behind the front bulkhead, height 600 mm, width 2,480 mm, depth 7,500 mm - Spare wheel mounted on the high-bed, behind the partition wall on the right - Staircase on the right side to access the front high-bed from the low-bed - Hydraulic coupling for uncoupling on the left, 6-fold Multi-Faster coupling - 6 lashing points, 3,000 kg rating, external on high-bed (drop-down lashing rings) - 2 lashing points, 5,000 kg rating, on top of the longitudinal members (rearward) Low-bed: - Climbing aids on the boom – extendable - External frame thickness: 8 mm - Low-bed telescoping by 4,000 mm, lockable every 500 mm - With sliding table, lockable every 250 mm - 28 lashing points, 10,000 kg rating, external in the outer frame - 24 plug-in stakes 90 x 90, evenly distributed for extending the low-bed to 3,050 mm width - 50 mm hardwood planks inserted between the extension tubes, 10 mm overhang Rear high-bed: - Rear high-bed sloped and perforated for later fitting of ramp mounting profiles using galvanized adapters - At the rear: ramp mounting profiles (Altec) – C rails - 8 lashing points, 10,000 kg rating, external on high-bed - 6 lashing points, 5,000 kg rating, in the excavator trough - 10 lashing points, 5,000 kg rating, for oversize load in external frame - Closure of excavator trough front and rear with removable wooden floor plate Electrics: - NATO spiral cable connection, power supplied by towing vehicle - Central amber beacon at rear - LED side marker lights - Standard vertical rear lights (LC5) - Work light on high-bed for illuminated low-bed area - Oversize load signage at front and rear, uncoupling control, safety sensor, and suspension pressure switch Air system: - 80 l aluminium air reservoir - TEBS modulator - Extension locking left and right (valve on side at rear high-bed) - Double release valve Hydraulics: - Hydraulic system on high-bed for steering, suspension, and detachable gooseneck Accessories: - 2 x 4 hardwood planks for low-bed extension and intermediate table support - 2 safety wedges for uncoupling - 4 wheel chocks Upon request, we can provide you with a leasing or financing offer. Mr. Ebert (Tel. ...) will be happy to assist you. More information is available on our homepage. Subject to errors and prior sale.

Stanje: rabljeno, konfiguracija osi: 2 osi, Leto izdelave: 2009, Oprema: ABS, = More options and equipment = - EBS - Electronic braking system - Rear air suspension - Front air suspension = Notes = For inquiries about the vehicle, Mr. Seidel will be pleased to assist you (by phone). Dinkel DSAFA 36000 inclined loader Additional rear vehicle spotlights, SAF axles, Wabco ABS, spring-loaded brakes, drum brakes, both axles steered, cargo area dimensions L 9.68 m x W 2.54 m / above the fifth wheel plate L 3.14 m x W 2.54 m, tire tread: 1st axle 10-12 mm, 2nd axle 11 mm, permitted total weight: 36,000 kg, unladen weight: 11,750 kg, payload: 24,250 kg. Upon request we can provide you with a leasing or financing offer. Mr. Seidel (phone) is at your service. You can find more information on our homepage. ... Subject to errors, changes and prior sale! ... Iasdpfxoyfr Hfo Agtot Steering axle = More information = Unladen weight: 11,750 kg Payload: 24,250 kg gross vehicle weight: 36,000 kg Outer dimensions: 0x2550x2800 Please contact Tobias Ebert for more information.

Stanje: rabljeno, Leto izdelave: 2019, For inquiries about the vehicle, Mr. Seidel will be happy to assist you (by phone). Ressenig SATL2-400.1 Telescopic Low Loader for Machines Lightly used articulated low loader – telescopic, equipped with 2 hydraulically steered 12-ton axle lines Manufacturer: Ressenig (Austria) • Lower deck length: approx. 5,500 mm retracted, approx. 8,500 mm extended (telescoped) • First registration: 05/2019 • Permissible total weight: 42,000 kg • Fifth-wheel load: 18,000 kg • Rear axle load: 24,000 kg • Overall length: approx. 12,860 mm retracted, approx. 15,860 mm extended • Unladen weight: 13,180 kg • Payload: 28,820 kg Iodpfx Ajyfrxnsgtjat • Width: 2,550 mm • Axles: DL-S axle lines, 12 tons each • Tridec independent suspension, hydraulically suspended and steered • Radio remote control for steering and air suspension • Tyres: 245/70 R 17.5 • Braking system: BBA air brake, EBS, spring-loaded brakes on both axles • Lowbed: telescopable by up to 3 meters, from 5.50 m to 8.50 m • Ramps: electro-hydraulic Other features: • Yellow revolving beacon • Spare wheel • Aluminium bridge inserts for use in the telescoped lowbed • Red/white extension boards for transporting oversize loads On request, we can provide you with a leasing or financing offer. Mr. Seidel (by phone) will be happy to assist you. You can find more information on our homepage. ... Subject to errors, prior sale, and changes! = Further Information = Please contact Tobias Ebert for further information.

Stanje: rabljeno, konfiguracija osi: 2 osi, Leto izdelave: 2024, Oprema: ABS, Za vprašanja glede vozila vam je na voljo gospod Seidel (po telefonu). Wörmann BauTL 105 55/200 nizkopodni priklopnik SAE-SMB osi, bobnaste zavore, Knorr ABS, zračna vzmetenja, vlečna zanka 40 mm, Duomatik, dimenzije tovornega prostora: dolžina 5.600 mm, širina 1.990 mm, višina 400 mm, profil pnevmatik: 1. os 14 mm, 2. os 13 mm Na željo vam pripravimo ponudbo za leasing ali financiranje. Gospod Seidel (tel.) vam z veseljem pomaga. Iajdpfx Agsyfqa Djtot Več informacij najdete na naši spletni strani. ... Pridržujemo si pravico do napak, sprememb in vmesne prodaje!!! - = Dodatne informacije = Lastna masa: 2.700 kg Nosilnost: 7.800 kg Skupna dovoljena masa: 10.500 kg Zunanje mere: 0x2550x3200 Za več informacij se obrnite na gospoda Tobiasa Eberta.

Stanje: novo, konfiguracija osi: 2 osi, Leto izdelave: 2021, Oprema: ABS, Technical data for EBERT TLS 43 ST Special Low Loader: - Permissible kingpin load: 19,000 kg - Permissible axle load: 24,000 kg - Gross vehicle weight rating (GVWR): 43,000 kg - Payload: approx. 32,200 kg - Low-bed length: 9,350 mm - Axle platform length: 2,700 mm - Overall width: 2,550 mm - Loading edge/low-bed height: approx. 200 mm – 350 mm - Oversize warning signs at front and rear with red/white panels - Tyres: 245/70 R 17.5 Steering system: TRIDEC Axles: 12,000 kg Gigant Axles, hydraulic steering Electrics: - Use of NATO spiral cable, power supplied by the towing vehicle Iodpfx Aoyfp Aqegtoat - Central warning beacon at the rear - Lateral LED marker lights - Standard vertical rear lights (LC5) Hydraulics: - Hydraulic system for steering mounted on the gooseneck Upon request, we can offer you a leasing or financing solution through Mercedes-Benz Bank. Mr. Ebert (Tel.) will be happy to assist you. Further information is available on our homepage. Subject to errors and prior sale! New general inspection, rental possible = Further information = GVWR: 43,000 kg Please contact Tobias Ebert for more details.

Stanje: rabljeno, Leto izdelave: 2014, Country of manufacture: NL Please contact Theo Lelie for further information. Ijdpoyrtnqsfx Agtoat

Stanje: rabljeno, Leto izdelave: 2009, Country of manufacture: NL Please contact Theo Lelie for further information. Isdpjyrtm Tefx Agtjat