Obdelovalni center BLOCK-HOUSE za lesene konstrukcije

Krüsi CM-40

Stanje: dober (rabljeno), Leto izdelave: 1996, Funkcionalnost: popolnoma funkcionalen, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Year of manufacture: 1996 Krüsi CM40, consisting of the following components: - Circular saw (cross-cut saw) - Log home milling unit, horizontal and vertical - Groove milling (horizontal) - Boring unit - Infeed table 6 m - Outfeed table 6 m KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Manufacturer: Krüsi Maschinenbau AG, CH-9105 Schönengrund AR Year of manufacture: 1996 CE marked Condition: Good, technically inspected and cleaned / ready for operation Operating Principle: Processing of timber for chalet / log house construction. Beams can be processed in a single pass - Cross-cutting - Horizontal and vertical milling of tenons/grooves in a single clamping - Drilling - Cutting the end grooves Workpiece capacity: - Maximum cutting height: 200 mm - Maximum cutting width: 250 mm Sturdy construction with welded frame. Machine (horizontal and vertical milling units) equipped with 4 special milling motors, with hardened and ground guideways for maximum machining precision. Carriage guidance via dust-protected and preloaded ball-bearing rollers. Working range up to 200 x 250 mm. Fully operational, with contactor control, Motors protected by thermal relay. Electrical equipment for 380 V, 50 Hz, with protective covers, Central connection for customer-side chip extraction, with 2 eccentric clamps, without milling tools (groovers). With hydropneumatic horizontal and vertical feed, electrically controlled, synchronized with the start of the milling motors. Rapid traverse and feed rate steplessly adjustable. Fully wired and installed, including air maintenance unit. Timbers thicker than 14 cm must be processed in two passes. Machine Description / Equipped with: 1. Saw Unit: Manual feed Spindle adjustment with analogue scale Saw blade Ø max. / bore-Ø: 400 / 30 mm Carbide-tipped with chip depth limiter (synchronous operation) Adjustable riving knife Motor speed [min-1]: 2900 Power (kW): 2.2 2. CM Milling Unit (Log House Unit) Hydropneumatic feed Spindle adjustment with digital readout Horizontal milling unit Cutter Ø: 180 mm Cutter width max.: 130 mm For cutter widths above 60 mm, only alloy cutters with indexable inserts may be used 2 motors, hydropneumatic feed, 2.2 kW each Feed: hydropneumatic Rapid traverse and working feed steplessly adjustable 3. Drilling Unit: Manual feed Spindle adjustment with analogue scale Drill holder: ER 25 collet Clamping Ø max.: 16 mm Drill Ø max.: 32 mm Motor [min-1]: 1450, 1.8 kW 4. Planing Milling Unit: Hydropneumatic feed Hodpfx Agjvfv Tfe Toi Spindle adjustment with digital readout Cutter Ø max.: 230 mm Cutter width max.: 60 mm Motor [min-1]: 2900, 3.0 kW 2 V-belts SPZ 9.5x1000 La Pneumatics Operating pressure on site min/max MPa (bar): 0.7/1 (7/10) Air consumption Nm3/h: 8 Electrical Equipment Operating voltage V/Hz: 380, 50 Rated power (kW): 8.8 - 15.8 depending on version Customer-side fuse protection: 3 x 25 A tr

Stanje: rabljeno, Sečnja hlodovine: 100–150 m³/h Sečnja manjših ostankov: 50–100 m³/h Teža: 3.165 kg Hsdpfx Agshclffe Tsi Največji premer hloda: 254 mm Sekalnik Söderhamn Eriksson 670-56 CC z električnim motorjem. Sekalnik Söderhamn Eriksson 670-56 je namenjen izdelavi sekancev za proizvodnjo celuloze, vlaknenih in ivernih plošč. Za surovino se lahko uporabljata tako okroglo lesno deblo kot tudi odpadek iz žagarskih obratov. Podajanje lesa pri sekalniku 670-56 poteka vodoravno, pod kotom 37,5° glede na vlaknasto smer. Sekanci enakomerne, visoke kakovosti se lahko izločajo na dnu ali pa se odpihnejo naravnost navzgor. Bodite med tistimi lesno-predelovalnimi podjetji, ki znajo pametno upravljati z razpoložljivimi viri.

Stanje: dober (rabljeno), Leto izdelave: 1996, Funkcionalnost: popolnoma funkcionalen, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 POS 1: Motorized Roller Conveyor Working width 400 mm, infinitely variable feed speed 2.0 kW motor, length 6000 mm POS 2: Longitudinal Saw Saw blade diameter 400 mm Pneumatic feed for cutting depth Main motor 4.0 kW POS 5: KRÜSI Chalet Construction Machine / Log House Production Machine Type CM 40 Machine No. 431 Year of manufacture: 1996 Hsdpfx Agehw N Npj Tei Saw Unit: Manual feed Spindle adjustment with analogue readout CM Milling Unit: Hydropneumatic feed Spindle adjustment with digital display Drilling Unit: Manual feed Spindle adjustment with analogue readout Face Milling Unit Hydropneumatic feed Spindle adjustment with digital display POS 6: Motorized Roller Conveyor Working width 400 mm, infinitely variable feed speed 2.0 kW feed motor Length 12000 mm 9 adjustable, pneumatically controlled stop flaps 10 lateral transfer pushers for material transfer POS 7: Assembly Table 4,400 mm x 12,000 mm Manufacturer: Sweden Year of manufacture: approx. 1985 Assembly table for further processing of the manufactured log house beams. 4 chain hoists for crosswise transport Gear motor with 4.0 kW

Stanje: dober (rabljeno), Leto izdelave: 1996, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Manufacturer: Krüsi Maschinenbau AG, CH-9105 Schönengrund AR Year of manufacture: 1996 Condition: Good, technically inspected and cleaned / ready for operation Operating Principle Processing of construction timber for chalet construction / log house manufacturing The beams can be processed in a single pass • Cutting to length • Horizontal and vertical milling of tenons / grooves in a single clamping • Drilling • Milling of end grooves Workpiece: • Max. cutting height: 200 mm • Max. cutting width: 250 mm Robust welded construction design. Machine (horizontal and vertical milling unit) with 4 special milling motors, equipped with hardened and ground guides for maximum machining precision. Carriage guided by dust-protected and preloaded ball bearing rollers. Working area up to 200 x 250 mm. Fully operational, with contactor control, motors protected by thermal relays. Electrical equipment for 380 V, 50 Hz, with protective covers, central connection for on-site chip extraction, with 2 eccentric clamps, Hjdpfju Uh T Dex Ag Tei without milling tools (rebate heads). With hydro-pneumatic horizontal and vertical feed, electrically controlled, operating together with spindle motor start-up. Rapid traverse and feed are steplessly adjustable. Fully wired and installed, including air maintenance unit. Beams with a thickness of more than 14 cm must be processed in two clamping steps. Such beams must be repositioned for re-milling to account for the excess thickness. Safety covers over moving parts with gas strut weight compensation. Machine Description / Equipped with: 1. Saw Unit: Manual feed Spindle adjustment with analog scale display Saw blade Ø max. / Bore Ø: 400 / 30 mm Tungsten carbide tipped with chip depth limiter (same direction of rotation) Adjustable riving knife Motor speed: min⁻¹ 2900 Power kW: 2.2 2. CM Milling Unit (Log House Unit) Hydro-pneumatic feed Spindle adjustment with digital scale display Horizontal milling unit Cutter Ø: 180 mm Max. cutter width: 130 mm For cutter widths above 60 mm, only cutters made from aluminum alloy with indexable inserts are to be used 2 motors, hydro-pneumatic feed, each 2.2 kW Hydro-pneumatic feed Rapid traverse and feed speed steplessly adjustable 3. Drilling Unit: Manual feed Spindle adjustment with analog scale display Drill holder: Collet ER 25 Clamping Ø max.: 16 mm Drill Ø max.: 32 mm Motor: min⁻¹ 1450, 1.8 kW 4. End Milling Unit Hydro-pneumatic feed Spindle adjustment with digital scale display Max. cutter Ø: 230 mm Max. cutter width: 60 mm Motor: min⁻¹ 2900, 3.0 kW 2 V-belts SPZ 9.5x1000 La Pneumatics On-site operating pressure min/max. MPa (bar): 0.7 / 1 (7 / 10) Air consumption Nm³/h: 8 Electrics Operating voltage V / Hz: 380, 50 Rated power kW: 8.8 - 15.8, depending on configuration Required on-site fuse: A 3 x 25 slow-blow Maximum simultaneous power in use: 4.4 kW Dimensions Machine width: 2400 mm Machine depth: 1600 mm Overall height (guard down): 1600 mm Overall height (guard up): 2200 mm Extraction connection Ø (floor extraction): Weight approx.: 1300 kg Incl. roller conveyor 2 x 6 m (2 x 4 m) Technical specifications subject to change!

Stanje: pripravljen za uporabo (rabljen), For turning plates, discs, or bowls up to 250 mm diameter. Machine equipped with vacuum clamping. Hjdpfxsrh Hnts Ag Tei

Stanje: novo, Leto izdelave: 2024, Magnetic separator for chip transport line Tube magnet with 4 magnetic plates (permanent magnet) Hinged door for easy removal of metal parts Tube diameter: 180 mm Hjdpfjcqvhwex Ag Tei Location: In stock at 54634 Bitburg - immediately available -

Stanje: zelo dobro (rabljeno), Leto izdelave: 2020, Kompletná píla na paletové rezivo pozostávajúca z: Hsdpfx Agjx T Azwo Tji 1. Manipulačný dvor Häwa s koreňovým reduktorom a odkornovačkou Valon Kone VK 90. Kalibrované meranie vstupu (výrobca Jörg). Triedenie do 28 boxov. Dĺžka dreva 2,0 - 5,0 m. Priemer kmeňov 20 - 90 cm. 2. Píla: pásová píla Möhringer s vozíkom Flexi Drive. Vyhľadávač štiepania. Podávanie guľatiny so stupňovým samostatným dávkovačom. Laserové meranie Bidac. Porez: Kallfass priečna kapovačka. Sekundárny rez: EWD Optimes so štiepkovačom a dvojvlnovou pílou NKU. Brodbaek automatický omietací stroj. Stohovací automat na hlavnú surovinu, zariadenie na manipuláciu s prázdnymi paletami pre hlavnú aj vedľajšiu surovinu. Robot Kuka na stohovanie vedľajších aj hlavných výrobkov, možné štyri rozmery. Kompletná mechanizácia, elektrické a elektronické rozvádzače, atď. Odvoz zabezpečený. Detailné plány alebo video je možné zaslať na požiadanie.

Stanje: rabljeno, Slot spindle 1 pc. Number of milling units: 4 pcs. Spindle diameter: 50 mm Control: Weinig, PC-Nexus # 2764 Weinig Unicontrol 6 with NC spindles ----- Machine will be cleaned and thoroughly inspected before delivery Technical Data Summary (For any additionally included accessories, please inquire) Pos. 1: Cross-cut saw ----- > Cross-cut saw, electronic, horizontally infinitely adjustable > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Maximum tool diameter: 400 mm > Motor power: 3.0 kW > Laser line for identifying the saw cut > NC length stop, mounted on slotted table included Positioning of the cross-cut saw integrated into control system. > Length: 3500 mm Pos. 2: Tenon and slot spindle ----- > Number of tools: variable, infinitely adjustable NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely adjustable 254 mm NC axis > Spindle speed: 3500 rpm > Spindle diameter: 50 mm > Maximum tool diameter: 320 mm > Motor power: 11 kW Pos. 3: 1st profiling spindle (climb-cut and counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Max. tool swing: 232 mm > Motor power: 7.5 kW Pos. 4: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, infinitely adjustable NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely adjustable 254 mm NC axis > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Max. tool swing: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Sash guide consisting of: Guide rail in the stop (area of climb-cut spindle), Sash support bar from above in the area of vertical right profile milling unit and profiling spindle. Pos. 5: Profile milling unit horizontal, top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed: 5,850 rpm > Max. tool swing: 130 mm > Axial adjustment 30 mm, 8 positions via pneumatic turret > Radial adjustment 125 mm, 8 positions via pneumatic turret Pos. 6: 3rd profiling spindle (hardware spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment 115 mm, 8 positions via pneumatic turret > Radial adjustment 100 mm, 8 positions via pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool swing: 210 mm > Motor power: 3.0 kW Additional features ----- > Network-capable > Rebate unit for tear-free rebating > Double-part package > Return conveyor for one-man operation: pivoting belt > Screen control > Tilt window device > Electronic angle display for tilt windows > Industrial PC, PC control/NEXUS > Weinig type production program > Without machining tools No original pictures available yet. Photos show an identical machine from our archive. ----- Hodpfx Ajvu Hfqjg Toi Price for the above machine on request! ----- Optional at extra cost: EUR 6,500.00 Note...

Stanje: novo, Leto izdelave: 2023, moč: 7 kW (9,52 KM), širina skobljanja: 520 mm, število rezil: 4, skupna masa: 483 kg, vrsta nastavitve višine: električni, premer gredi skobeljnika: 120 mm, višina skobljanja: 240 mm, SCM MiniMax s 52es Thickness Planer Specification: Hsdpfxequ U Dns Ag Tei • Condition: New • Manufacturer: SCM • Planer table width: 520 mm • Planer table length: 850 mm • Minimum workpiece thickness: 3 mm • Maximum workpiece thickness: 240 mm • Maximum cutting depth: 5 mm • Motor power: 7 kW • Supply voltage: 400 V • Cutterblock: 4 conventional knives • Cutterblock diameter: 120 mm • Cutterblock speed: 5000 rpm • Maximum planing width: 520 mm • Feed speed: 5 / 8 / 12 / 18 m/min • Extraction port diameter: 120 mm • Weight (net): approx. 493 kg • Overall dimensions: 144 x 108 x 110 cm (W x L x H) Additional Information: • Factory new machine • Actual item condition shown in the pictures • Possibility to test and inspect the machine on-site • Price listed in the auction does not include VAT or transport costs • Available immediately from stock in Italy

Stanje: novo, Technical data: Working width: 1100 mm Abrasive belt size: 1120 x 2150 mm Max working height: 160 mm Calibrating steel roller diameter: 150 mm Rubber roller diameter: 150 mm Sanding shoe width: 50 mm Total motor power for both sanding units: 11 kW Abrasive belt speed: 16/18 m/s Feed motor power: 0.55 kW Infinitely variable feed belt speed: 4–20 m/min Hjdpfsgtm U Aex Ag Toi Work table motor power: 0.25 kW Pneumatic shoe lift/drop: YES