Balairka

HSM GmbH + Co. KG VK 8818 FU

Stanje: zelo dobro (rabljeno), Leto izdelave: 2015, obratovalne ure: 20.331 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 970 mm, dolžina polnilne odprtine: 1.800 mm, dolžina bale: 1.200 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 750 kg, skupna masa: 33.000 kg, Good day, We hereby offer, subject to prior sale, a used, complete baling line consisting of a baler from the manufacturer HSM, type VK 8818 R-FU including conveying technology and wire tying stations. The following technical data have been taken from the operating manual and manufacturer brochures. We assume no liability for the correctness or completeness of this information. Technical Data Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours, as of September 2025 Number of bales pressed: 29,020 bales, as of September 2025 Main press force: 1,000 kN Specific press force: 120 N/cm² Shear-edge ejector press force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time in idle operation: 8.3 seconds Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length variable from 600 up to 2000 mm Drive capacity: 2 x 45 kW, frequency-controlled Total connected load: 110 kW Total current consumption: 213 A Fuse protection: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Throughput rates at bulk density of 20 kg/m³: 12.86 t/hour bulk density of 50 kg/m³: 32.15 t/hour Bale weight at a bale length of approx. 1.2 m: 650 to 750 kg per bale, depending on material Hydraulic oil tank volume: 2,000 L HVI 46 PLC: Siemens S7-300 Operator panel: Siemens TP 700 Dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Installation dimensions with conveyor technology: 35,000 x 8,480 x 7,745 mm (L x W x H) Weight baler: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional special equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to standard 2 x 45 kW motors at the same output Manual activation/deactivation of wire tying strands to save tying wire with non-expanding materials Shear-edge ejector with 121 kN press force Wire break/end sensor monitoring, with baler shut-off in the event of wire breakage or wire end Bale slide Optical warning signal mounted on the control cabinet Pgedpfx Ajyz Af Eopmol Condition of the baler: The entire baling system (baler and conveyor technology) is in good, immediately operational condition and has been cleaned, lubricated, and maintained weekly by the operator in accordance with the manufacturer’s specifications. Technical Data Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain belt conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Length of feed belt: 7,000 mm Length of ascending belt: 14,500 mm Length of goose neck: 1,550 mm Inclination: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of delivery: - HSM VK 8818 R-FU baler - Service platform - Bale slide - Wire deflection stations - Wire spool trolleys (without wire spools) - Stadler KF 1800 chain belt conveyor - Crosswise sliding belt conveyor - Pit cover from the feed conveyor to the pit - Second control cabinet for baler operation at the conveyor - Machine documentation in English Delivery time: The entire plant has already been dismantled and stored, and will be ready for loading shortly after payment is received. We would be pleased if this or one of our other balers is of interest to you. Your service team, Mertens & Frowein GmbH

Stanje: rabljeno, Leto izdelave: 2015, obratovalne ure: 25.000 h, Funkcionalnost: popolnoma funkcionalen, dolžina rotorja: 2.200 mm, vrtljajska hitrost (min.): 58 obr/min, skupna masa: 30.000 kg, moč: 220 kW (299,12 KM), vhodna napetost: 400 V, Desfibradora de eje único robusta de baja velocidad, adecuada para la pretrituración de una amplia variedad de materiales sin la presencia de grandes contaminantes. Podpfxjw Tk E As Apmogl Aplicación: Trituración de residuos industriales y comerciales, películas, materiales de embalaje, textiles, papel, caucho, madera de demolición, palets, bobinas de papel, tambores de cable, plásticos mixtos para recuperación térmica y de materiales, sueltos o prensados en balas. Lindner Jupiter 2200 Potencia de accionamiento: 2x 110 kW (ABB) Casete de criba curva: 148 mm Armario de control: completo con (FU-ABB) Refrigerador de recirculación: Sí, incluido Abertura de trabajo: 2190 x 1750 mm Volumen de llenado: aprox. 5 m³ Longitud del rotor: 2190 mm Circunferencia del rotor: 745 mm Velocidad del rotor: 50Hz: 58 rpm Número de cuchillas de rotor: 24 uds Dimensiones de cuchilla, cuchilla de punta: 145x145x47 mm Contracuchillas inferiores: 6 uds Peine rascador superior: 6 uds Alimentación hidráulica: 11 kW Peso: aprox. 30 t Dimensiones LxAnxAl mm: 5300 x 3260 x 3090 mm Tolva: incluida Plazo de entrega: inmediato

Stanje: novo, Leto izdelave: 2025, Features: - Overband neodymium magnetic separator - HP - Dust suppression - Belt speed control Pgodpfx Aew Elbdjpmsl - Self-propelled drive for semi-trailer

Stanje: zelo dobro (rabljeno), Proizvajalec: Strautmann Pgodpfx Apov Aiymomjl Tip: PP 1207 Plus Format bale (DxŠxV): 1200 x 1100 x 730 mm Teža bale: cca 400 - 500 kg Zunanje dimenzije (DxŠxV): 1850 x 1047 x 3079 mm Transportna višina: 2500 mm Polnilna odprtina: 1190 x 600 mm Stiskalna sila: 59 ton / 580 kN Učinkovitost: 1 - 2 bale/uro Število povezav: 4 Teža stiskalnice: 2300 kg Napajanje: 400 V / 50 Hz Moč: 4 kW Mesto namestitve: pokrito-notranje/zunanje Nivo hrupa: manj kot 80 dB(A) Leto izdelave: 2003-2005 Na voljo so tudi stiskalnice Strautmann PP 1207 letniki 2009-2011 cena 5500 EUR Na voljo so tudi stiskalnice Strautmann PP 1208 letnik 2014-2015 Strautmann AutoLoadBaler letniki 2018 cena 7500 EUR

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, leto zadnje generalne obnove: 2025, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed Pgodpfx Apjvf E Avemel - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Stanje: pripravljen za uporabo (rabljen), Number of knives: 6, rotor diameter: 350 mm, motor power: 50 kW, with design as reinforced steel/welded construction and documentation. Inspection is possible. Year of manufacture unknown, comprehensively overhauled in 2022. Pjdpfxon Tpmue Apmsgl

Stanje: rabljeno, Leto izdelave: 2014, obratovalne ure: 18.700 h, skupna masa: 27.000 kg, število rezil: 41, dolžina rotorja: 1.800 mm, moč: 200 kW (271,92 KM), največja hitrost vrtenja: 87 obr/min, vhodna napetost: 400 V, Počasno delujoč robusten enogredni drobilnik. Primeren za grobo predhodno drobljenje različnih materialov brez večjih motilcev. Uporaba: Drobljenje industrijskih in komercialnih odpadkov, folij, embalažnih materialov, tekstila, papirja, gume, lesenih ruševinskih ostankov, palet, papirnih rol, bobnov za kable, mešanih plastik za termično in materialno predelavo — v razsutem ali v balah. Lindner Jupiter 1800 Pogonska moč: 1x 200 kW (ABB) Sito: SK 80 mm Krmilna omara: komplet z (FU-ABB) Vračalni hladilnik: Da, vključeno Delovna odprtina: 1790 x 1750 mm Vstopna prostornina: pribl. 4 m³ Dolžina rotorja: 1770 mm Krožnica rotorja: 745 mm Število vrtljajev rotorja: 50 Hz : 87 min⁻¹ Število rezil rotorja: 41 kos Pgodpfx Aow Tk Udspmsl Dimenzija koničnih rezil: 87x87x38 mm Spodnja proti-rezila: 5 kos Zgornji strgalo: 5 kos Hidravlični dozirnik: 11 kW Teža: pribl. 27 t Dimenzije D x Š x V mm: 4800 x 3260 x 3090 mm Lijak: vključen Dobavni rok: takoj

Stanje: dober (rabljeno), Leto izdelave: 2014, obratovalne ure: 18.520 h, Single-shaft shredder, especially suitable for secondary shredding and granulation of pre-shredded material. Applications: Commercial waste for thermal or material recycling, e.g. paper, cardboard, plastics and foam materials, rubber, leather, textiles, floor coverings, etc. Lindner Power Komet 1800 Year of manufacture: 2014 Control cabinet: fully equipped with ABB frequency converter Recooling unit Operator console Pgedpfxowxmb Ej Apmsl Hopper Drive motors: 200 kW Hydraulic unit: complete Total weight: approx. 21 t Dimensions (LxWxH): approx. 5000 x 2800 x 3000 mm Inspection: possible by prior arrangement Delivery time: immediate

Stanje: pripravljen za uporabo (rabljen), Tehnični podatki za stiskalnico Dixi 60 AUTOMAT Pjdpfx Aev Amw Njpmsgl Nakladalna odprtina (š x v): 1550 x 1000 mm Pogonska moč: 31,5 kW Tlačna sila: 60 t Teža bale (odvisno od materiala): 350–600 kg Dimenzije bale (š x v x g, nastavljivo): 1100 x 800 x 300–1600 mm Čas stiskanja/cikel: 13/24 s Teža stroja: 7000 kg

Stanje: pripravljen za uporabo (rabljen), HSM V-Press 860 baler, year 2008-2009, price: €5,800 Pressing force: 54 kN Specific pressing force: 63.46 N/cm² Drive power: 7.5 kW Cycle time: 25 s Loading height: 1,110 mm Feeding opening (W x H): 1,195 x 650 mm Bale size (L x W x H): 1,200 x 780 x 1,200 mm Bale weight: 480 kg Machine dimensions (W x D x H): 1,797 x 1,247 x 2,985 mm Machine weight: 2,008 kg Binding material: wire Pjdpfjra Rbgex Apmegl Pressable materials: film, mixed paper, cardboard, die cuttings, textiles, Big Bags, EPS HSM V-Press 860 plus baler, year 2013-2015, price: €8,000 HSM V-Press 860 L baler, year 2015, price: €9,000 HSM V-Press 860 plus baler, year 2019, price: €9,000 HSM V-Press 860 plus baler, year 2024, price: €10,000 HSM V-Press 860 new, ex-display, year 2020, price: €13,000 4-fold wire bale tying Bale dimensions (L x W x H) mm: 1,200 x 800 x 1,000–1,200 Bale weight: approx. 500 kg Technical data (L x W x H): 1,213 x 1,824 x 2,987 mm Feed opening: 1,200 x 565 mm Cycle (seconds): 35 Pressing force (T): 54 Power supply: 400 V (three-phase) HSM V-Press 860 plus B baler, year 2020, price: €14,000 Pressing force: 594 kN Voltage/Frequency: 400 V / 50 Hz Power: 4 kW Feed opening (W x H): 1,500 x 651 mm Bale size (L x W x H): 1,500 x 780 x 1,200 mm Bale weight: 550 kg Loading method: manual Machine dimensions (W x D x H): 2,099 x 1,245 x 2,985 mm Machine weight: 2,336 kg Binding material: wire Pressable materials: film, cardboard Idle cycle time: 25 s