4-osni obdelovalni center CNC

HOMAG BMG 211 / 60 / 15 / K

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2007, potovalna razdalja osi X: 4.600 mm, pomik osi Y: 1.935 mm, pomik po osi Z: 275 mm, število osi: 5, This 5-axis Biesse Rover C9.50 was manufactured in 2007. It offers a large working area (X=4600 mm, Y=1935 mm, Z=275 mm), an automatic lubrication system, and a control unit for 5-axis interpolation. The machine is equipped with a vacuum system, a conveyor belt for chip extraction, and liquid cooling. If you are looking for high-quality CNC machining capabilities, you should consider the Biesse Rover C9.50 that we have for sale. Contact us for more information. Work Table and Clamping • 8 ATS panel holders (L = 1525 mm) and 24 sliding rails • Automatic positioning of panel holders and sliding rails (EPS X-Y) • Pneumatic locking system, divided into 2 working areas in X • 8 rear reference stops, stroke 115 mm • 8 stops, stroke 140 mm, positioned at 1175 mm (L = 1280 / 1525 / 1800 mm) • 8 stops, stroke 140 mm, positioned at 770 mm (L = 1280 / 1525 / 1800 mm) • 4 side stops, stroke 140 mm (2 left + 2 right) with pneumatic system • 4 removable middle stops, stroke 140 mm (2 left + 2 right) with pneumatic system • Sensor for detecting lowered stops • Pneumatic system for lifting bar holders • 6 lifting bar holders for easy loading (H = 74 mm modules) Vacuum • Vacuum system for a 250 m3/h pump • 250 m3/h rotary vane vacuum pump for the standard vacuum system Machining Units and Configuration • C3-A1 composition: • Device for mounting chip deflectors with pneumatic or inductive sensors on a 5-axis machining unit • Flange for mounting units on a working unit with 5 interpolating axes (units only usable when the electric spindle is vertical) • C3-P2 composition: • Additional Z-carriage for rear machining units, controlled by an independent Z-axis • 16 vertical and 4 horizontal drilling spindles in Y-direction • Chain tool changer with 22 positions (180 mm center distance) • Iron gripper for chip deflector with pneumatic or inductive sensor, located in the chain tool changer • RH chip deflector with inductive sensor for standard electric spindle or 15 kW 5-axis electric spindle (requires device for chip deflector; requires flange for mounting units when using a 5-axis electric spindle; requires C-axis when using a standard electric spindle) Systems • Automatic lubrication system • Control unit with 5 interpolating axes Additional Equipment • Additional overhauled 5-axis main spindle available • Conveyor belt for chips and scrap (chip conveyor) • Liquid cooling unit for liquid-cooled systems (can cool two electric spindles or one electric spindle plus a liquid-cooled drilling head) Iedjx D H Hcopfx Ablsaw Note: The technical specifications and descriptions are taken from the original order confirmation and are for informational purposes only; they are not binding.

Stanje: rabljeno, Leto izdelave: 2018, Delivery time approx. 5 months. Machine from school operation – TOP condition, low hours (edge banding unit unused). Without tools. Plus dismantling / delivery / installation and commissioning / training. Includes Maestro 3D and Pro View. MORBIDELLI P200 Working area X-Y: 3,110 x 1,620 mm, workpiece height Z180 mm. Edge banding – Made for You. The CNC machining centre is equipped with an extensive range of edge banding tools to meet every requirement in woodworking. MAIN ADVANTAGES: - High performance, featuring the advanced edge banding unit H80C, drilling spindles with 8,000 rpm and the most robust spindle technology on the market, providing over 1,000 maintenance-free operating hours. - Superior and more comprehensive equipment: suction cups can be excluded and configured with the FLEX worktable to optimally equip the machine according to requirements. - Easier and more intuitive programming thanks to the integrated CAD-CAM module for edge banding technologies 'MAESTRO EDGE'. - Easy to use: the lowered frame keeps the worktable accessible at all times; the control cabinet and vacuum pump are integrated, and in the PRO SPACE configuration, there are no safety barriers necessary. Frame construction: The base structure is a monolithic construction out of thick-walled steel, reinforced throughout the entire machine bed by welded square-section plates, providing exceptional rigidity. The shape of the machine bed, with a broad base, ensures lasting precision and stability. The supporting structure consists of a particularly robust monolithic steel base, heavily ribbed and very rigid; the especially wide footprint is specifically designed to provide stability, guaranteeing consistent accuracy regardless of operating conditions, with no need to anchor the machine to the floor. The base forms a large and solid support for the moving gantry: the working unit therefore benefits from a balanced, stable, and resilient support capable of withstanding maximum loads, ensuring superior performance and higher accuracy. The moving gantry is made from a solid single piece anchored to the base and runs on high-quality prismatic guides with ball-bearing carriages. The working unit is mounted on it and moves along the Y and Z axes on prismatic guides with ball-bearing carriages. Movement of the lower moving unit (X axis) and the working unit along the moving beam (Y axis) is via a helical rack and pinion system, giving more tooth-to-tooth engagement for greater acceleration and higher speeds along the X and Y axes. The specially designed helical teeth reduce wear and lower mechanical noise. Iodpfx Ajyuw Srsbljaw The vertical Z axis is driven by a ball screw, ensuring perfect balance under dynamic loads and supporting rapid acceleration and deceleration. The main milling unit is directly coupled to the Z-axis slide, ensuring absolute machining quality.

Stanje: rabljeno, Leto izdelave: 2013, Funkcionalnost: popolnoma funkcionalen, Naprodaj: prečna lepilka za furnir Fisher+Rueckle FZR-24, letnik 2013! Dolžina traku furnirja: 400–1100 mm (dvojna linija) / 350–2100 mm (enojna linija). Širina traku: 50–500 mm. Debelina traku: 0,3–1,5 mm. Največji nazivni izhod/cikli stroja: 30 ciklov/min. Povprečna hitrost proizvodnje: 17–20 ciklov/min. Učinkovita dolžina grelne cone: 2478 mm. Priključna moč: 22 kW. Komprimiran zrak: 6 bar. Vrste lepila: na osnovi PVA ali UREE. Iaodpfsumrf Aex Abljw

Leto izdelave: 2013, stanje: pripravljen za uporabo (rabljen), Connected load: 4 kW, weight: 1 t. Ijdpehlp Efjfx Abljaw

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2024, Linija za proizvodnjo peletov - popolna linija - popolnoma avtomatizirana Stiskalnica Salmatec Kladivni mlin Rematec Trakasti sušilec Isdpfx Abszg Eudeleaw VAI stroj za pakiranje v vreče Hladilnik Sito Paletizator Manj kot 1000 ur proizvodnje – certificirano Možnost ponovne namestitve na lokaciji Možnost usposabljanja operaterjev na lokaciji

Stanje: novo, Leto izdelave: 2024, nosilnost na konzolno roko: 500 kg, višina police: 3.200 mm, skupna dolžina: 2.100 mm, skupna višina: 3.200 mm, razmak osovin: 1.000 mm, nosilnost na stojalo: 2.500 kg, Cantilever Rack in Hot-Dip Galvanized Design: Scope of delivery: - 3 uprights, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) - 12 cantilever arms with 1.8 m usable depth (for chipboard panels approx. 2.1 m deep) - Longitudinal and diagonal braces for 4 m rack length (upright spacing 1.3 m) - Mounting material (bolts, nuts and washers) Net price: €2,490.00 plus VAT Detailed Description: - Robust steel construction made of IPE profiles (bolted system) - Rack height: 3,200 mm - Load capacity per upright: 2,500 kg - Base section and cantilever arms with 1,800 mm usable depth (for 2,100 mm chipboard depth) - Cantilever arms height adjustable in 100 mm increments - 4 bolted cantilever arms per upright as standard (= 5 storage levels) - Load capacity per cantilever arm: 500 kg - Including longitudinal and diagonal bracing for 1,000 mm upright spacing - Rack length = 2,100 mm Iajdpfxeqt Dmys Ablew - Includes mounting material (excluding floor anchors) - Supplied with assembly instructions and load signs C4 according to DIN standard - Made in Germany - Short delivery times Our cantilever racks are exclusively manufactured in Germany. We offer reliable shipping with prior notification before delivery. Material is sensibly packed for easy unloading. Delivery for stock items can be made approximately 1 week after receipt of order. When installed outdoors, the load capacities are reduced due to wind and snow loads. The subfloor must be concrete, level, suitable for dowelling, and capable of supporting the applied loads. The customer is responsible for checking and ensuring soil condition, bearing capacity, and any necessary official permits. Uprights must be anchored to the floor on site; wall anchoring is neither necessary nor recommended. According to occupational safety regulations, it is recommended that the uprights provide at least 500 mm projection above the top storage level.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2013, obratovalne ure: 3.000 h, 5-axis CNC portal machine; Console table with 6 movable consoles, each with 2 vacuum cups, side and longitudinal positioning pins, LED position display for vacuum cups Venture 316 Future Package 10 lift rails, connection for Power-Clamp, vacuum connection for templates WORKPIECE PARAMETERS: – Maximum workpiece lengths: All units, single: 3300 mm; pendulum max.: 1740 mm Tool diameter 25 mm: single 3475 mm; pendulum max.: 1915 mm – Workpiece width: Front stop: 950 mm, all units / 1050 mm with tool diameter 25 mm Rear stop: up to 1400 mm / 1550 mm – Workpiece thickness: – Max. 250 mm including clamping fixtures – Up to 60 mm with standard clamps SAFETY AND PROTECTION FEATURES: EC-compliant; SAFETY FENCE ON RIGHT WITH DOOR Left and rear: wall installation! Equipment: 10 kW Drive5C spindle and 14-position tool changer (carousel) + 9-position linear changer, side-mounted Drilling head with 16 spindles (vertical 12 / horizontal 4 / none at 90°) AGGREGATE INTERFACE DRIVE5C+ Iaodpfx Aoy E Npfjblew TOOL MEASURING PROBE CHANGER SOFTWARE FOR POSITION MEASUREMENT AND ROTATION OF CNC COORDINATES TOOL TRANSFER STATION COOLANT TANK FOR MACHINING SPINDLE VACUUM PUMP 300/360 m3/h Powerclamp pneumatic package Control: POWERCONTROL PC85 with POWERTouch control system; IPC PowerPack, Operator pedestal for program start; camera system with tablet PC WOODWOP CAD/CAM INTERFACE STANDARD Documentation and control texts: German Delivery includes only the pictured tools and HSK holders!

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2021, potovalna razdalja osi X: 4.000 mm, pomik osi Y: 1.670 mm, pomik po osi Z: 500 mm, število osi: 4, This 4-axis CNC machining center was manufactured in 2020. It features a 12 kW milling spindle with a speed range of 1,000–24,000 rpm and C-axis rotation from 0–360°. The machine is equipped with a linear tool changer with 12 positions and a comprehensive drilling head with 16 spindles. In addition, it has a robust safety system with light curtain. Take advantage of this opportunity and purchase this CNC machining center Felder Format 4 Profit H 200. Contact us for further information about this machine. • Automatic central lubrication • Working area: X 3300 mm / Y 1280 mm / Z 250 mm (clearance height from console level depending on clamping system) Ijdpfx Asx D D Hmsbleaw • Operator terminal on the left side of the machine • Handheld terminal with axis speed control and emergency stop • Software: Woodflash (CNC panel, tool database, program editor) • Position display for workpiece support and vacuum suction pads • Vacuum connection for template routing (left side), connection diameter 12 mm • Vacuum pump: 1x, total suction capacity 90 m³/h @ 50 Hz or 108 m³/h @ 60 Hz • Milling spindle: 12 kW (S6), HSK F63, 1,000–24,000 rpm, full rated power at ~12,000 rpm, air-cooled; C-axis 0–360° • Tool changer: 12-position linear on the left side of the machine frame, including storage for aggregates; max. tool diameter 250 mm; max. tool length 240 mm • Drilling head DH 16 4H 2S: 12 vertical spindles (7X / 5Y); 4 horizontal spindles (2X / 2Y); pre-stroke 70 mm; drilling depth 70 mm; shank diameter 10 mm • Grooving saws: 2 (one X, one Y); max. blade diameter 120 mm; max. thickness 5 mm; continuously adjustable speed up to 7,500 rpm • Safety: Front light curtain system

Stanje: rabljeno, No. 3176 WEINIG Hydromat 1000 Planing and Moulding Machine Used, year of manufacture 2007 6 Spindles: bottom-right-left-top-top-bottom Electronic feed: 6 - 60 m/min Working width: 80 - 150 mm Working height: 23 - 65 mm Finished lamella width: 4 - 15 mm Max. number of lamellae: 16 pcs Lamella lengths: 400 - 4000 mm 1st spindle horizontal bottom: Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool circle 125 - 180 mm 2nd spindle vertical right: Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm 3rd spindle vertical left: 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Iodpju Agh Sefx Abljaw Max. profile depth 35 mm Axial adjustment 80 mm Pressure shoe in front of spindle, swiveling, pneumatic roller pressure 4th spindle horizontal top: 15 kW, 6000 rpm, diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 5th spindle horizontal top as saw spindle: Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment reduced to 25 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 6th spindle horizontal bottom as saw spindle: Brake motor 30 kW, 5000 rpm Axial adjustment reduced to 25 mm Diameter 45 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm All profiling spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of feed rollers opposite left spindle, axial 35 mm Shortened roller distance opposite right spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in table, lateral pressure roller Automatic Waxilit/lubricant pump Machine with 4-roller outfeed, oscillating shafts extended to 200 mm 2 driven, toothed rollers in outfeed table 2 driven, toothed rollers in machine table Pressure beam ahead of and discharge after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electric height adjustment of upper spindles and feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transport and installation Subject to errors in description and price Transport and loading by us available as an option To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended The sale is made in "as is" condition Technical data, description of condition, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: "sold as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Terms of payment: prices plus statutory VAT, payment before collection or dispatch Delivery terms: ex site

Stanje: rabljeno, Leto izdelave: 2004, številka stroja/vozila: 02919475, - Manufacturer: Cefa - Model: KLEENSPRAY - Year of manufacture: 2004 - Working width: 1,200 mm - Working height: 900 mm ± 20 mm - Operator side: left - Spray gun drive: single version - Dry extraction system - Extraction nozzle diameter: 490 x 350 mm - Exhaust air capacity: 6,500 m³/h - Paper belt transport system - Feed speed continuously adjustable: 1.5 – 7 m/min - PLC control with touch screen - Number of installed spray devices: 0 pcs. - Height-adjustable spray devices - Number of paint pumps: 0 pcs. - Suitable for solvent-based paints - Suitable for water-based paints - Length: 4,450 mm - Width: 3,360 mm + 1,000 mm - Height: 2,600 mm - Total connected load: ~7.1 kW / 28.6 A - Voltage, Hz: 400 / 50 Iajdpsv N D Ewsfx Ablsw - Location: in stock - Voltage fluctuations max. +/- 5% _____ Optionally, we can also provide you with an offer for assembly and commissioning of the system, as well as training for your personnel. On request, we also offer regular maintenance and servicing of the machine. For further information, please do not hesitate to contact us!