Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Multimax Plus Satteltieflader Hebebett

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long, rear chamfer approx. 1,000 mm x 6° * For tractor units: 4 x 2 and 6 x 2 * ASPÖCK UNIBOX * On the gooseneck and rear chamfer: grating floor with 5 mm steel reinforcement * 2 inch king pin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Round NATO socket on the front connection rail (Maeler & Kaege VG 96 917) * One pair of plug-in ALU side boards on gooseneck, approx. 400 mm high, anodized finish * One LED work light each mounted top left and right on the front wall, operated by on/off switch (control via tractor unit is not possible in this case) LOADING PLATFORM: * Platform length approx. 9,600 mm, with rear chamfer approx. 900 mm x 6° * Platform behind the gooseneck hydraulically liftable/lowerable, length approx. 3,000 mm, load capacity approx. 9,000 kg * Continuous grating floor on both lift bed and platform with approx. 5 mm steel base as additional reinforcement, suitable for point loads TYRES: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steering * 3rd axle with electro-magnetic reverse lock triggered by reverse gear and manual activation * 1st axle with start assist * Technical axle load: 12,000 kg per axle * Air suspension with lift and lower valve HYDRAULIC LOADING RAMPS: * One pair of two-piece AXS steel ramps with grating surface, approx. 4,920 mm long and approx. 900 mm wide * Hydraulically folding ramp tips * Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward * Flashing lights on the outer edges of ramp tips, switch next to ramp controls * Ramp safety in road position via quick release * Painted sand coating on ramp frame and ramp tip * Mechanical drop-leg type supports on the sides of the ramps for stability when docking to unloading ramps * Ramp operation valves located on the right side of the vehicle BRAKE SYSTEM: WABCO EBS-E brake system according to EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection PAINTWORK: * Trailer in carmine red (RAL 3002) * Rims silver gray * Side boards in bare aluminum * Wheel hubs according to axle manufacturer Dedpfx Alsy Auhhetsuw * Lamp panel pure white (RAL 9010) EQUIPMENT: * Removable front wall made of steel, approx. 1,600 mm high, with supply line connection strip to tractor approx. 1,000 mm from bottom edge of outer frame profile * Lashing chain fixing options on the inside left and right of the front wall, including aluminum trays below left and right for storing chains or tensioning straps * Behind the front wall, approx. 12 mm thick DELIGNIT panel, bolted * 2 additional pairs of bolt-on lashing rings (LC 5,000 daN) * Electric cable winch, approx. 5,400 kg pull capacity, with radio remote control. Steel cable approx. 24 m long, cable diameter approx. 9.5 mm, including cable pressure roller

Stanje: novo, največja dovoljena obremenitev: 36.400 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment. Full specification available upon request. - Gooseneck in SNT design to optimize the platform length, approx. 3,700 mm long, rear with a chamfer of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S, & 15-pin sockets - 3 kW electro-hydraulic power pack to control hydraulic functions, except for hydraulic winches. Without installation of supply connections on the tractor unit - Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then every approx. 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper section of the outer beams of the gooseneck for a bolted lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the outer beam of the gooseneck (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - The gooseneck and rear chamfer feature grating flooring with 5 mm steel reinforcement - 2-inch king pin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable to supply the electro-hydraulic power pack and/or the electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) - On the gooseneck: 1 pair of detachable aluminum side walls, approx. 400 mm high, anodized finish LOAD PLATFORM: - Load area, approx. 9,600 mm long, with rear chamfer approx. 900 mm x 6° - Loading platform behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg - TPMS tire pressure monitoring system according to ECE R 141 - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steered. 3rd axle with electro-magnetic reverse lock activated via reverse gear and manually - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand at our discretion, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel underlay as additional reinforcement, designed for point loads: - on the lift bed - on the load platform Dsdpfx Aljyhkqujtsuw - Painted sand coating on the cover plates of the gooseneck as well as transition areas between gooseneck and lift bed, lift bed and load platform, and between load platform and ramps - 1 spare wheel mounting bracket under the load platform, right side before the axles - Cutouts in the outer frame of the platform and lift bed for hooking in tension belts (LC 2,000 daN) - 11 pairs of recessed lashing rings in the outer frame of the platform, foldable outward (LC 10,000 daN): - 3 pairs in the outer frame of the lift bed - 8 pairs in the outer frame of the platform - 11 pairs of recessed lashing rings along the central girder (LC 5,000 daN): - 3 pairs in the lift bed - 8 pairs in the rear part of the platform - Control valves for the hydraulic ramps on the right side of the vehicle - 1 pair of foldable mechanical rear supports with one-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a...