Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader Radmulden

Stanje: novo, največja dovoljena obremenitev: 36.360 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Neck (Gooseneck): * Gooseneck with front corners tapered approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading area with rear bevel approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) Kedpeyhkq Uefx Adkjdi * Wheel recesses with square profile climbing strips approx. 15 x 15 mm as well as lower-width extensions * Between the first and second axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (approx. 670 mm wide) – max. point load 5 t/each * Recess in the bevel as well as projecting into the loading area for excavator dipper stick accommodation (approx. 2,900 x 750 x 210/290 mm [L x W x H]) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cutouts in the outer frame of the loading area for fastening ratchet straps (LC 2,000 daN) Two-part steel ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm hardwood covering * Ramp with hydraulically folding ramp sections and hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting and lowering valve Tyres: * Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection * Final painting with 2 coats of 2-component topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL 841GL system * Rims in silver grey Including the following additional equipment: * 2" kingpin * Galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Rear electro-hydraulic unit, under the loading area * On the gooseneck, aluminium side and rear plug-in walls, approx. 2,440 x 400 mm (L x H). The rear galvanized stanchions are removable. (Superstructure length approx. 2,560 mm) * One galvanized toolbox integrated in the tapered gooseneck * 2 pairs of WADER container pockets in the loading area for one 20' or 30' container * 3 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * 3 additional pairs of removable, galvanized covers over the wheel recess – max. point load 3.5 t/pc * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional, hang-in intermediate table, approx. 300 mm wide * Interm

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards Kodpfx Adsh Hm Tzokodi - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 37.820 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment. Complete specification available on request. Gooseneck: - Gooseneck with front corners beveled approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring approx. 30 mm thick Loading Platform: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing stripes approx. 15 x 15 mm, including widenings at the bottom - Between the 1st and 2nd axles, one fixed pair of wheel recesses approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-part removable galvanized covers over the wheel recesses (W approx. 670 mm), max. point load approx. 5 t/piece - Recess in the bevel and extending into the loading platform for accommodating excavator stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of folding-out lashing rings (LC 5,000 daN) - 3 pairs of folding-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) One-Piece Steel Ramps: - 1 pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting system, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm do not need to be considered in the vehicle length in transport position Landing Gear: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load per axle: 12,000 kg - Electro-magnetic reverse lockout, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tool Tyres: - Tyres 235/75 R 17.5 3PMSF, brand of our choice - TPMS tyre monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. To display correctly, the tractor unit must be able to receive and show this data. Brake System: - WABCO brake system in compliance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Kdjdpfow Tpqwex Adksi Steel Construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa); S690QL/S700MC (yield strength 690MPa) Electrical System: - Electrical system in accordance with EU regulations - 24 Volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front terminal bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot blasted with a turbine blasting system after welding - Second blasting process with corundum for optimum coating adhesion - HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection - Final paint with two layers of 2K topcoat, single color in RAL 3002 Carmine Red, according to the RAL 841GL system - Rims in silver - Rear section metallized and in RAL 9010 (con...

Stanje: novo, največja dovoljena obremenitev: 37.635 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete stock of vehicles, including those available immediately or at short notice, can be found on our website. Excerpt from the equipment features. Full equipment list available on request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized, one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramp with hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 40,000 kg Kdodpfx Adjxtc Ubskoi In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not need to be included in the vehicle length when in transport position Loading platform: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and extensions at the lower section * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Includes 3-piece removable galvanized covers over the wheel recesses (approx. 670 mm wide) - max. point load 5 t/piece * Recess in the chamfer and extending into the loading platform for excavator boom (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of flat lashing rings at the front of the loading platform (LC 10,000 daN) * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 3 pairs of outward folding lashing rings (LC 10,000 daN). 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the platform for securing straps (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t static test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, activated via reverse gear and manually * Air suspension with lift and lowering valve * Axle tools Tyres: * Tyres 235/75 R 17.5 3PMSF – manufacturer at our discretion * TPMS: Tyre Pressure Monitoring System in accordance with ECE R 141. Data transmission to the towing vehicle via the standardised EBS interface per ISO 11992. For correct display, the towing vehicle must be able to relay and display this data Braking system: * WABCO braking system compliant with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel structure: * Steel structure made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system compliant with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets * Connections as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paint finish: * Complete steel structure automatically blasted with turbine blasting machine after welding * Secondary shot-blasting with corundum for optimum coating adhesion * Top coat: 2 layers of 2K finish, single colour in RAL 3002 Carmine Red, as per RAL system 841GL * Wheels in silver * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested with salt spray test in accordance with ISO 9227-NSS * Cavity sealing with specialist wax Including the following additional equipment: * 2-inch king pin * One ver

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads Kdjdehlz R Sepfx Adkoi - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, največja dovoljena obremenitev: 38.140 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our full range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Gooseneck: - Gooseneck with approx. 45° chamfered front corners and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Approx. 30 mm thick hardwood flooring Loading platform: - Telescopic loading platform with rear slope approx. 1,000 mm x 8° - Between the 1st and 2nd axle, a pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece, removable, galvanized cover over the wheel recesses (W approx. 670 mm – max. point load 5 t / each) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - 4 pairs of folding external lashing rings (LC 5,000 daN) - 3 pairs of folding external lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - 235/75 R17.5 3PMSF tyres, manufacturer of our choice - TPMS – Tire Pressure Monitoring System according to ECE R 141 - Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992 - The tractor unit must be capable of transmitting and displaying these data for correct indication. Axles: - BPW axles and suspension, 2 axles fixed, 3rd axle trailing steer - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve. Axle tools Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor Electrical system: - Electrical system in accordance with EU regulations - LED lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicators - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: - Steel construction made from high-strength fine-grained steel - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Kdodpow Tpq Dofx Adkei Painting: - Entire steel structure automatically shot-blasted with shot-blast machine after welding - Second blasting with corundum for optimal coating adhesion - HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% Zinc / 15% Aluminum) to ensure best corrosion protection - Final coating with 2 layers of 2K top coat, single color RAL 3002 Carmine Red. Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavities sealed with special wax Including the following accessories: - On both the gooseneck and at the rear left and right, one holder for warning boards, including socket - Spare wheel holder in front of the bulkhead (without spare wheel) - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized connection panel at the front - Galvanized folding supports under the rear slope of the loading platform - Hardwood rear impact protection from gooseneck rear wall to loading platform - 1 pair of recessed lashing rings along the central frame at the rear in the slope (LC 10,000 daN) - On the gooseneck, aluminum side and rear walls

Stanje: novo, skupna masa: 58.000 kg, Leto izdelave: 2026, MAX100 4 A 8.60 U Low Loader Semi-Trailer Technical Specifications Speed: 80 km/h Gross weight: 60,800 kg Fifth-wheel load: 18,000 kg Axle load: 42,800 kg Unladen weight: Payload: Gooseneck length: 3,850 mm Loaded fifth-wheel height: 1,250 mm Loading area length: 8,600 mm Extendable by: 5,400 mm Axle spacing: 1,360 mm Rear steering radius: 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck With front corners chamfered at 45° and rear bevel approx. 760 mm x 10° Kdedpog Sk T Djfx Adksi 3 pairs of lashing rings (LC 5,000 daN) Hardwood flooring, 30 mm thick Loading area, extendable version with rear bevel approx. 1,000 mm x 8° 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) 1 pair of horizontal lashing rings at front of loading area (LC 10,000 daN) Hardwood flooring approx. 48 mm thick, checker plate over axles Ramps Two-piece steel ramps One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 mm x 800 mm with approx. 48 mm thick hardwood covering Ramp with hydraulically folding ramp sections, hydraulic lifting system and hydraulically adjustable. Maximum load capacity per pair: 40,000 kg Tyres 235/75 R 17.5 Braking system in accordance with EU standards with EBS-E (4S3M) without connecting lines to the tractor unit Paintwork First-class, durable corrosion protection of the standard shot-blasted welded frame guaranteed by 2-component zinc-dust primer High-quality 2-component (2K) topcoat, single-color finish in RAL shades of your choice Rear section metallized and painted in RAL 9010 (pure white) Landing Gears: JOST mechanical landing gears with 2-speed gearbox for 24 t Lifting capacity (test load 50 t) Steel structure made of high-strength fine-grain steels. Steel Grades: Steel structure made of high-strength fine-grain steel S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrics in accordance with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Accessories included: One galvanized steel front wall approx. 400 mm high 2" king pin 4 wheel chocks with holder on the front wall Bracket for a rotating beacon at rear of the trailer SAF axles, two fixed axles, one trailing-steering axle, air-suspended, with drum brake, with lifting/lowering function. Trailing steering axle with electro-magnetic reverse lock, can be activated via reverse gear or manually. Axle tools Mounting at the rear of the gooseneck for ALU loading ramps Galvanized folding supports under the bevel of the loading area Mechanical safety lock for the loading area One spare wheel with holder in front of the front wall Yellow reflective tape along the sides, extension and rear of trailer, in accordance with EU regulations. At the galvanized front connection strip, yellow-red air couplings On gooseneck and rear plate left and right, each with mount for warning plates and socket included Mudflap at trailer rear Manual and documentation On gooseneck, plug-in ALU sideboards and rear wall approx. 2,440 x 400 mm (L x H) The rear galvanized stake pockets are removable Body length approx. 2,560 mm, +/- 46 kg 3 pairs WADER container locks in the loading area for a 20', 30' or 40' container (± 30 kg) 6 pairs of stake pockets for plug-in stakes

Stanje: novo, konfiguracija osi: 3 osi, skupna dolžina: 9.300 mm, skupna širina: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R17.5, medosna razdalja: 1.360 mm, barva: modra, Leto izdelave: 2023, Oprema: dvižna zadnja plošča, Farbe: Blau Nutzlast: 54.465 kg Hauptmerkmale: Hersteller: Faymonville Modell: MAX 110-Z-4AA-9.30-U Fahrgestellnummer: YAMT14XX4N0107629 Baujahr: Neu und unbenutzt Gewichte / Ladefähigkeit: Sattellast: 23.000 kg Achslast: 12.000 kg je Achse Gesamte Achslast: 48.000 kg zul. Gesamtgewicht (zGG): 71.000 kg Eigengewicht: 16.535 kg Nutzlast: 54.465 kg Kdodpfx Adsuu Hcfjkei Achsen: Achsenhersteller: BPW Hydraulische Lenkung Luftfederung mit Hub-/Senkventil WABCO-Bremssystem Bereifung: 245/70 R17.5 – Michelin (Lastindex 146/146 F) 1. Achse als Liftachse Abmessungen: Ladeflächenlänge: 9.300 mm ausziehbar um: 6.500 + 6.800 mm Ladeflächenbreite: 2.540 mm Ladehöhe: 900 mm Weitere Ausstattungen: Doppelt ausziehbare Ladefläche Containerverriegelungen Ausschubverbreiterungen + Holzauflagen für Breitenverbreiterung Zurringe Satz doppelt klappbare Auffahrrampen Zentralschmieranlage 1x Ersatzrad + Halterung JOST Stützvorrichtung Elektrik 24 Volt Königszapfen 2.0″ Eine verzinkte Stahlbordwand Elektrisch betriebene Hydraulikpumpe Manuelle Lenkung Twistlocks = Weitere Informationen = Allgemeine Informationen Baujahr: 2023 Achskonfiguration Reifengröße: 245/70 R17.5 Federung: Luftfederung Hinterachse 1: Zwillingsbereifung, Liftachse, max. Achslast: 12.000 kg, gelenkt, BPW Achsen; Reifenprofil links innen: 100%, links außen: 100%, rechts innen: 100%, rechts außen: 100% Hinterachse 2: Zwillingsbereifung, max. Achslast: 12.000 kg, gelenkt; Reifenprofil links innen: 100%, links außen: 100%, rechts innen: 100%, rechts außen: 100% Hinterachse 3: Zwillingsbereifung, max. Achslast: 12.000 kg, gelenkt; Reifenprofil links innen: 100%, links außen: 100%, rechts innen: 100%, rechts außen: 100% Hinterachse 4: Zwillingsbereifung, max. Achslast: 12.000 kg, gelenkt; Reifenprofil links innen: 100%, links außen: 100%, rechts innen: 100%, rechts außen: 100% Gewichte Leergewicht: 16.535 kg Nutzlast: 54.465 kg zul. Gesamtgewicht: 71.000 kg Funktionalität Ladehöhe: 900 mm (Hinweis: Angabe 65535 cm in Daten war fehlerhaft) Aufbau ausziehbar: Ja Zustand Allgemeiner Zustand: Sehr gut Technischer Zustand: Sehr gut Optischer Zustand: Sehr gut Finanzen Preis: Auf Anfrage Weitere Informationen Bitte wenden Sie sich für weitere Informationen an Stefan Schaapveld.

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump Kdodpfx Aek Aht Uedkoi - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2007, dolžina tovornega prostora: 15.220 mm, širina tovornega prostora: 2.520 mm, vzmetenje: zrak, velikost pnevmatike: 235/75/17.5, barva: zelen, Leto izdelave: 2007, Oprema: ABS, = Dodatne opcije i oprema = - Vazdušno oslanjanje - Centralno podmazivanje = Dodatne informacije = Kdjdsxpu Ixepfx Adksi Dimenzije guma: 235/75/17.5 Marka osovina: BPW ECO Oslanjanje: Vazdušno oslanjanje Zadnja osovina 1: Dupli točkovi; Upravljiva; Kočnice: disk kočnice Zadnja osovina 2: Dupli točkovi; Upravljiva; Kočnice: doboš kočnice Prazna masa: 13.780 kg Nosivost: 24.220 kg Dozvoljena ukupna masa: 38.000 kg Izvlačiva platforma: Da NOOTEBOOM EURO-38-02 NISKOPODNI PRIKOLICA VAZDUŠNO OSLANJANJE 2X HIDRAULIČNO UPRAVLJIVA BPW ECO OSOVINE DIMENZIJA GUMA 235/75/R17.5 TRANSPORTNA POVRŠINA DUŽINE 975 CM, IZVLAČIVA DO 700 CM, UKUPNO 16,75 M ŠIRINA 252 CM VISINA TRANSPORTNE POVRŠINE 55 CM DEBLJINA TRANSPORTNE POVRŠINE 31 CM UTOR ZA RUČICU NA ZADNJOJ STRANI 282 X 70 X 30 CM KUKA PRSTENOVI OZNAKE STRANICA ZA PREDNJI I ZADNJI DEO CENTRALNO PODMAZIVANJE REZERVNI TOČAK ZAPATITE NAS NA INSTAGRAMU, FACEBOOKU I TIKTOKU ZA VIDEO SNIMKE NAŠIH KAMIONA I MAŠINA U PONUDI. GOVORIMO NEMAČKI WE SPEAK ENGLISH HABLAMOS ESPAÑOL