Transporter za drobtine

DGS SSF650P50

Stanje: rabljeno, Leto izdelave: 2013, Technical Details: Belt width: 600 mm Voltage: 460 V / 60 Hz Total power requirement: 3.5 kW Approximate machine weight: 2,300 kg Approximate machine dimensions (LxWxH): approx. 9.0 x 1.4 x 3.0 m Hinged Belt Conveyor, Unused With coolant tank including pump (submersible centrifugal pump), delivery rate 250 l/min, sufficient for a delivery height of 25 m Chip inlet length (A) max. 3,000 mm (extension with sheet metal tray with rubber lining 3,000 x 1,100 mm) Total insertion length: 5,000 mm Belt width (H): 600 mm Discharge height (C) above floor: 1,800 mm Rjdpfx Ageu Nupdetet The chip conveyor has 4x swivel casters below and can be fixed to the floor with anchor bolts.

Stanje: dober (rabljeno), Spindle diameter: 80 mm Spindle taper: SK50 Spindle speeds: 11 - 1000 rpm X-axis travel: 1700 mm Rjdpfsphl Ecex Agtet Y-axis travel: 1800 mm Z-axis travel: 1800 mm Spindle extension (W-axis): 710 mm Table dimensions: 1100 x 900 mm Elbo digital readout: On Y-axis and Z-axis Equipped with: - Rotary table - Several tool holders Spindle motor: 7.5 kW Machine dimensions (LxWxH): 5100 x 2650 x 3300 mm Machine weight: 10 tons

Stanje: rabljeno, Leto izdelave: 2003, Drehdurchmesser 190 mm Drehlänge 620 mm Steuerung Fanuc Series 18i-TB Gesamtleistungsbedarf 15 kW Maschinengewicht ca. 13,5 t Raumbedarf ca. 5350X3350x2395 m CNC Dreh- und Fräszentrum NAKAMURA TOME Rjdpfx Ajxiy Auogtot Super NTJ Baujahr 2003 Steuerung Fanuc Series 18i-TB - Hauptspindel muss überholt werden. - Oberer Revolver ist mit einer G42 Turbo- Luftangetriebenen Spindel 60000 U/min und Steuergerät GTR 3 nachgerüstet. Anzahl der Achsen: 9 Anzahl der Revolver: 2 Max. Drehdurchmesser: 190 mm Max. Drehlänge: 620 mm Stangendurchlass: bis zu 65 mm Umlaufdurchmesser über Bett: 190 mm Anzahl: 2 (Haupt- und Gegenspindel) Spindelnase: A2-6 Antriebsleistung: 15 kW Max. Drehzahl: 60000 U/min X-Achse: 345 mm Y-Achse: +/- 45 mm Z-Achse: 1240 mm B-Achse: +/- 91° oben voll Servogesteuert 0,001° Stangendurchlass: D 65 mm - 12-fach Revolver für angetriebene Werkzeuge - 24-fach Revolver für Drehwerkzeuge (Doppelhaltertechnik) - mit viel Zubehören - 2 x HB-Futter Hainbuch

Stanje: dober (rabljeno), The driven tools listed here, VDI 50, are designed for a tool turret manufactured by SAUTER. They are in good condition and fully functional, previously used on a GILDEMEISTER CTX 600 CNC lathe. 6 x driven tools, straight type, manufacturers NACKE + WTO, VDI 50 for SAUTER tool turret: Article No.: XVI 24275 1 drilling and milling tool, straight type, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, No. 40.5040 / 80 96 / 027.1, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €545.00 plus statutory VAT Article No.: XVI 24277 1 drilling and milling tool, straight type, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, No. 40.5040 / 80 96 / 027.3, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €400.00 plus statutory VAT Article No.: XVI 2687 1 drilling and milling tool, straight type, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT Article No.: XVI 2687 1 drilling and milling tool, straight type, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT Article No.: XVI 2687 1 drilling and milling tool, straight type, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT Article No.: XVI 2687 1 drilling and milling tool, straight type, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT Rodpfx Ajbql S Hsgtjt Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Leto izdelave: 2009, stanje: dober (rabljeno), številka stroja/vozila: 120P1109, OFFER 21407 Motorized Vessel/Drum Rotator with Rail-Mounted Carriage Technical Specifications: - Total load capacity (powered + idler unit): 40,000 kg - Load capacity per vessel rotator: 20,000 kg - Workpiece diameter approx.: 500 – 3,500 mm - Support roller center distance adjustable via trapezoidal-thread spindle - Roller diameter: 500 mm - Roller width: 150 mm - Powered unit with dual-side drive - Infinitely variable rotation speed - Handheld remote for forward and reverse operation - Drive: 400 V - Both units mounted on rail carriages - Required space for powered unit: approx. W 3,800 x H 1,150 x D 1,350 mm - Required space for idler unit: approx. W 3,600 x H 1,150 x D 1,350 mm - Weight powered unit: approx. 2,500 kg Rodohcnhmspfx Agtst - Weight idler unit: approx. 1,800 kg

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, največja hitrost vretena: 6.000 obr/min, pomik po osi Z: 700 mm, moč vretenovega motorja: 32.000 W, proizvajalec krmilnikov: SIEMENS, model krmilnika: C200-sl, število osi: 5, This 5-axis Index C200 was manufactured in 2023 and offers advanced features for horizontal turning. This machine is ideal for precision and efficiency in metalworking, providing a significant upgrade for improving production quality. Take advantage of the opportunity to purchase this Index C200 horizontal lathe. Contact us for further information. Additional Equipment • Software options: OPC UA for host computer integration (up to 200 variables). ChipMaster cycle for chip breaking control. • Environmental data: Noise level: 73.8 dB(A) Machine Advantages Technical Advantages • Control system: Based on SINUMERIK 840D SolutionLine (SL) with SINAMICS S120 drives. 18.5" TFT color display with PCT touch (IP65). Siemens operating interface in German. • Interfaces: 4x USB 2.0 (2 on the control panel, 2 in the panel). Network enabled for NC data transfer (logical drives). • Safety: Siemens Safety Integrated (ProfiSafe). • Turret mechanics: Hydraulic locking, AC motor with spur gear. Drive power per tool carrier: 10 kW (25% duty cycle), max. 8,000 rpm. • Tool holder: Cylindrical shank D25x48 (DIN69880) with W-slots for higher repeat accuracy. Driven tools possible at every station (can only be rotated in working position). • Cooling unit: 13 kW for hydraulics, spindles and control cabinet. Connection for cooling water (20°C ±2°C, 30 l/min, 25% glycol). • Chip conveyor: Hinge belt conveyor (by KNOLL) with 180-liter container, discharge height 840 mm. Coolant system: 750-liter tank, 8-bar/20-80-bar pumps. • Interface for bar loader: UNIMAG4-compatible (external loaders require a special cover). Maximum bar length: 1,035 mm (short bar operation). Gantry loading device: Pneumatic gripper (Ø 10-90 mm, max. 3.5 kg). Conveyor belt with switch for finished parts/cut-offs. Additional Information Control Panel Operating voltage: 400V Control voltage: 24V DC Frequency: 50Hz Nominal output: 54kW Connected load: 65kVA Rated current: 94A Max. pre-fuse: 100A Main Drive Main and counter spindle Spindle head mount: OD 140mm, ID 85mm Front bearing diameter: 110 mm Max. torque (100%/40%): 125/170 Nm Min./max. clamping pressure: 8/80 bar Piston area pressure: 57 cm² Piston area tension: 57 cm² Max. clamping force: 45,600 N Max. traction force: 45,600 N C-Axis: Drive: Spindle hollow shaft motor; direct spindle angle measurement system Position deviation (VDI/DGQ 3441): Psmax = 0.01 degrees Turret Tool Carrier 1 X-axis travel: 110 mm X-axis rapid traverse: 30 m/min X-axis acceleration: 9 m/s² X-axis feed force: 5,000 N Z-axis travel: 320 mm Z-axis rapid traverse: 50 m/min Z-axis acceleration: 9 m/s² Z-axis feed force: 5,000 N Y-axis travel: 100 mm Y-axis rapid traverse: 15 m/min Y-axis acceleration: 9 m/s² Y-axis feed force: 5,000 N Stations: 14 with cylindrical shank holder D25x48 Tool Carrier 2 X-axis travel: 110 mm X-axis rapid traverse: 30 m/min Rodpfxsyyuvto Agtst X-axis acceleration: 9 m/s² X-axis feed force: 5,000 N Z-axis travel: 550 mm Z-axis rapid traverse: 50 m/min Z-axis acceleration: 9 m/s² Z-axis feed force: 5,000 N Y-axis travel: 100 mm Y-axis rapid traverse: 15 m/min Y-axis acceleration: 9 m/s² Y-axis feed force: 5,000 N Stations: 14 with cylindrical shank holder D25x48 Tool Carrier 3

Stanje: zelo dobro (rabljeno), Leto izdelave: 2001, X-travel: 185 mm Z-travel: 360 mm B-travel: 460 mm Control: Mazatrol 640 T Max. swing diameter: 550 mm Max. turning diameter: 280 mm Max. workpiece weight: 200 kg Bar capacity: 51 mm Main spindle speed: 35–6,000 rpm Milling spindle speed range: 25–4,500 rpm Rapid traverse (X/Z axes): 30/33 m/min Rapid traverse (B axis): 30 m/min Tool turret: 12 stations Approx. machine weight: 4,100 kg Capacity: Chuck size: 6” Max. swing diameter: 550 mm Standard turning diameter: 221 mm Max. turning diameter: 280 mm Max. bar capacity: 51 mm Distance between spindle nose and turret face: 80–535 mm Main spindle: Speed: 35–6,000 rpm Rodoyukf Sopfx Agtjt Spindle bore: 61 mm Sub-spindle: Speed: 35–6,000 rpm Spindle bore: 52 mm Turret: Number of stations: 12 Tool dimensions: External turning tool: 20 mm Internal turning tool: 32 mm Milling drill: 16 mm Tapping tool: M12 End mill: 16 mm Milling spindle speed: 25–4,500 rpm Equipment/Accessories: Tool holders Tools Driven tools Turning tool holders Coolant system Chip conveyor Documentation

Stanje: rabljeno, Leto izdelave: 2008, x-axis travel: 410 mm y-axis travel: 570 mm z-axis travel: 140 mm Control: Mazatrol Matrix Maximum machining diameter: 545 mm Maximum machining length: 519 mm Main spindle speed: 35 - 6,000 rpm Tool holder: Capto C6 Rapid traverse (X/Y/Z axes): 30/26/33 m/min Performance / Capacity: Maximum swing: 545 mm Maximum machining diameter: 545 mm Maximum outside diameter for bar work: 51 mm Maximum machining length: 519 mm Maximum workpiece weight: - Chuck work: 150 kg - Bar work: 200 kg Main Spindle: Spindle speed: 35-6,000 rpm Spindle bore diameter: 61 mm Maximum torque: 161 Nm Tailstock: Rapid traverse: 8 m/min Travel range (engaged/retracted): 434/281 mm Milling Head: Type: Single spindle with ATC Tool shank type: Capto C6 Tool dimensions: External turning tool: 20 mm Internal turning tool: 32 mm Milling tool: Max. 90 mm diameter x 200 mm length Milling spindle speed: 15-12,000 rpm Equipment/Accessories: -Chip conveyor -Mist extraction Rsdpfjyt R Idjx Agtot -Tools -Documentation

Stanje: rabljeno, Leto izdelave: 2014, INDEX C200 CNC stružnica 3 revolverske glave 2 vretena Fanuc krmilnik: 31i-Model B Motorna aksialna stikala: 6 kos Motorna radialna stikala: 13 kos Nosilci orodij: 11 kos Nosilci vrtalnih palic: 21 kos Zatič: 1 kos Vložki za polnjenje + tulke: Ø51/Ø46/Ø41 Nove MBL vložke za polnjenje: 2 kompleta 2 optični merili obnovljeni pri HEIDENHAIN 1 Balluff škatla z robotskimi rokami z različnimi senzorji, bližinskimi stikali in kabli Motorizirani jermeni: 6 kos Set antivibracijskih vložkov za MBL polnilnike Čas obratovanja: Redpfxoxxm Hfj Agtjt Čas vklopa: 37.946 Hidravlične ure: 37.500 Proizvodni čas: 26.500 Z MBL podajalnikom palic

Stanje: rabljeno, TECHNICAL SPECIFICATIONS - Number of axes: 4 MILLING SPINDLE - Tool holder: BT50 - Spindle drive power: 45 kW Rodjw D Hwwspfx Agtjt - Spindle speed: 12,000 rpm LINEAR AXES - Travel X/Y/Z axes: 1700/1400/1240 mm - Rapid traverse speed (X/Y/Z): 48 m/min - Feed speed (X/Y/Z): 20 m/min SWIVEL AXIS B - Travel: 360° - Minimum resolution: 0.001° TOOL CHANGER - Tool changer type: Bras chargeur - Number of tools in magazine: 60 - Tool change time: 6 s PALLET CHANGER - Pallet changer type: Rotopalette - Pallet size: 1250x1250 mm - Number of pallets: 2 - Max. pallet load: 3,000 kg - Distance from table center to spindle nose: 70–1470 mm - Max. workpiece diameter: 1,970 mm ELECTRICAL SUPPLY - Supply voltage: 400 V WEIGHT AND DIMENSIONS - Machine weight: 32,500 kg MACHINE HOURS - Power-on hours: 34,422 h ACCESSORIES - Control: Fanuc 31i-model B5 - Interface: Ethernet / RS232 / USB / PCMCIA - Electronic handwheel - Synchronized tapping - 3-color status light - Coolant tank * with high-pressure pump: 70 bar * internal coolant supply (through-spindle coolant) * paper filter * coolant chiller * cabin washing system - Chip conveyor - Tool measurement probe - Workpiece measuring probe: Renishaw RMP60 - Electrical transformer