Arburg Allrounder 520 S 1600-290 / 290

Arburg Allrounder 520 S 1600-290 / 290

This 6-axis Arburg Allrounder 520 S 1600-290 / 290 was manufactured in 2015. It features a highly wear-resistant thermoplastic cylinder with a diameter of 30 mm, and a drive unit powered by a 30 kW motor. The machine is equipped with state-of-the-art controls for both injection units and supports multi-component processing. If you are looking for a high-quality injection moulding machine, you should consider the hydraulic Arburg Allrounder 520 S 1600-290 / 290, which we are offering for sale. Please contact us for further details.

• Injection Units and Plasticising
• 1st Injection Unit:
• Complete thermoplastic cylinder, 30 mm, highly wear-resistant
• Nozzle contact force controlled, programmable
• aXw control ScrewPilot
• 2nd Injection Unit:
• 2nd injection unit 290, vertical
• Complete thermoplastic cylinder, 30 mm, highly wear-resistant
• Open nozzle 30 mm with nozzle tip; extended nozzle tip +20 mm; radius 15
• Heating band for open nozzle
• Nozzle contact force controlled, programmable
• aXw control ScrewPilot
• Standard worm gear coupling; coupling geometry: double-sided
• Multi-component processing; separating plane device on short skids for 2nd unit
• Injection with mould closed ("flying injection")
• Drive, Hydraulics, and Cooling
• Drive unit with 30 kW motor
• 65 l/min charging flow rate
• Accumulator module, 64 l capacity (max. 230 bar); accumulator drive
• Continuous oil cooling and filtration; enhanced cooling performance
• Controlled machine cooling circuits
• Clamping System, Ejector, and Core Pulls
• Clamping plate set; central Ø 125 mm
Nksdoyxdwdepfx Advsw
• Minimum installation height 450 mm (extended)
• Ejector pressure P/Q controlled (requires T2); ejector plate
• Core pulls:
• Core pull 1, simultaneous movement (P/Q controlled, programmable)
• Core pull 2, simultaneous movement (P/Q controlled, programmable)
• Core pull 3, simultaneous movement (P/Q controlled, programmable)
• Pneumatic core pull control 4 incl. pressure reducer
• Electric core pull control 1 (requires VE 436/00)
• Mould Connections Pneumatic/Hydraulic
• Electrical connection pneumatic NVD 1 (in the mould)
• Electrical connection pneumatic NVD 2 (in the mould)
• Electrical and hydraulic connection NVD 3 (in the mould)
• Electrical and hydraulic connection NVD 4 (in the mould)
• Blow-off device 1 with pressure reducer; connection for blow-off device 2
• Cooling Water and Mould Circuit
• Shut-off valve for cooling water (inlet); shut-off valve for cooling water (inlet 2)
• Cooling water filter 100 µm (supply)
• 3 cooling water circuits for fixed mould plate; 3 cooling water circuits for moving mould plate
• Basic equipment for 2nd cooling water manifold (manual) with 7 free cooling circuits
• Controls and Electrics
• Selogica direct control; technology level
• Protection of heating circuits (1-6 with 16 A)
• 15 electric heating circuits for mould heating
• Boost function for heating circuits (hot runner)
• Upper guard open, raised to safety distance
• Error indication with warning light
• Operator authorisation via chip card (EUROMAP 65)
• Interfaces and Connectivity
• Interface for conveyor belt (machine base)
• Prepared for six-axis robot with SELOGICA interface
• Robot interface (EUROMAP 67), 50-pin
• Emergency stop interface (24-pin, 2-channel)
• Basic equipment for electric axis control
• Host computer interface OPC-UA

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.