Rezervni deli

WEINIG

Stanje: rabljeno, Leto izdelave: 2006, skupna višina: 1.700 mm, skupna dolžina: 1.200 mm, skupna širina: 1.300 mm, Lastna teža: 750 kg Cena: Po dogovoru - Leto izdelave: 2006 - Dokumentacija na voljo: Ne - CE-certifikat: Ne - Serijska številka: 108442 - Transportne dimenzije: 1200mm x 1300mm x 1700mm (d x š x v) - Transportna teža [kg]: 750 kg - Transportni paketi [kos]: 1 Finančne informacije Hnodjyu Sb Ispfx Adkoi DDV: Naveden cena ne vključuje DDV DDV/obračun razlike: DDV je odbit za podjetja Dostava in odkup možno kadarkoli za vso industrijsko opremo Lukas van Rossum

Stanje: dober (rabljeno), Leto izdelave: 1996, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 226-60368, skupna širina: 2.200 mm, skupna višina: 2.000 mm, skupna dolžina: 4.500 mm, skupna masa: 4.000 kg, WEINIG PROFIMAT 23 Four-Side Planer Hedpfxsyu Iwlo Adksni - Operating voltage: 380 V - Frequency: 50 Hz - Clamping length working spindle: 247 mm, jointing spindle: 130 mm, left spindle: 130 mm, top spindle: 240 mm - Tool length surfacing spindle: 240 mm, jointing spindle: 130 mm, left spindle: 130 mm, top spindle: 240 mm - Spindle diameter on surfacing, jointing, left, and top spindle: each 40 mm - Axial adjustment travel: 5 mm, radial: 15 mm, jointing spindle: 40 mm, radial: 50 mm, axial adjustment travel left spindle: 40 mm, radial: 200 mm, axial adjustment travel top spindle: 40 mm, radial: 120 mm - Max. cutting circle behind fence: 200 mm - Max. cutting circle working spindle: 145 mm, jointing spindle: 200 mm, left spindle: 200 mm - Below table (working spindle): 20 mm, below table (jointing spindle): 15 mm, left spindle: 15 mm - Min. cutting circle diameter working spindle: 125 mm, jointing spindle: 100 mm, left and top spindle: 100 mm - Max. cutting circle diameter working spindle: 145 mm, jointing spindle: 200 mm, left spindle: 200 mm, top spindle: 200 mm - Spindle speed on all spindles: 6,000 rpm - Extraction connection on all spindles: 140 mm - Max. chip removal on all spindles: 10 mm - 2nd bottom spindle – clamping length: 240 mm, tool length: 240 mm, spindle diameter: 40 mm - Axial adjustment travel: 35 mm, radial: 68 mm - Max. cutting circle below table: 200 mm, min. 18 mm - Cutting circle diameter: min. 100 mm, max. 200 mm - Speed: 6,000 rpm - Motor power: 4 – 11 kW - Extraction diameter: 140 mm - Chip removal: from 0 to 0.5 mm - Surfacing table length: 2000/2500 mm - Surfacing table adjustment range high/low: 10 mm - Jointing fence adjustment range: 10 mm Note: The item must be picked up definitively between 01 and 10.06.2016 on a date to be arranged. FCA D-75433 Maulbronn – loaded onto truck

Stanje: dober (rabljeno), Leto izdelave: 1999, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 87960, skupna višina: 2.700 mm, skupna širina: 2.500 mm, skupna dolžina: 9.000 mm, skupna masa: 5.000 kg, premer žaginega lista: 400 mm, vhodna napetost: 380 V, proizvajalec krmilnikov: WEINIG, WEINIG UNICONTROL 06 avtomatski stroj za okna - Obratovalna napetost: 380 V - Frekvenca: 50 Hz - Stranski pritisk, delovna širina: 30 - 220 mm - Obdelovalni profili, širina profila: 30 - 220 mm - Višina profila: 30 - 100 mm - Dolžina profila: 2600 mm - Vključno s transportnim trakom - Širina traku: 250 mm Hnodpsyu Ir Asfx Adkji - Prav tako vključuje razne rezkalne glave Pozor: Izdelek je treba obvezno prevzeti med 01. in 10.06.2016 na dogovorjen datum. FCA D-75433 Maulbronn – naloženo na tovornjak

Stanje: rabljeno, Leto izdelave: 2001, Number of spindles: 5 units Working width: 230 mm Planing height: 120 mm Length of jointer table: 2000 mm Feed speed: 5–24 m/min Four-side planer Weinig Profimat 26 S Summary: - 5 spindles (bottom, right, left, top, bottom) - Combined control of right spindle (axial), top spindle (axial), and glazing bead discharge - Working width (with tool cutting circle 125 mm): 20–230 mm - Working height (with tool cutting circle 125 mm): 8–120 mm Detailed description: 1ST SPINDLE - First lower horizontal spindle - Motor with brake, 5.5 kW - Diameter: 40 mm - Speed: 6,000 rpm - Tool cutting circle: 125–145 mm - Axial adjustment 5 mm - Rebating device - Hardened table insert in front of 1st lower spindle 2ND SPINDLE - First right vertical spindle - Motor with brake, 7.5 kW (shared with left vertical spindle) - Diameter: 40 mm - Speed: 6,000 rpm - Tool cutting circle, 15 mm below table level: 100–200 mm - Tool cutting circle, 40 mm below table level: 100–180 mm - Max. tool diameter behind fence: 180 mm - Max. profiling depth: 35 mm - Axial adjustment 40 mm - Right spindle, pneumatically controlled axially (40 mm) via selector switch, max. saw blade diameter 180 mm - Insertion segment: 125 mm 3RD SPINDLE - First left vertical spindle - Shared motor with 1st right vertical spindle - Diameter: 40 mm - Speed: 6,000 rpm - Tool cutting circle, 15 mm below table level: 100–200 mm - Tool cutting circle, 40 mm below table level: 100–180 mm - Max. tool diameter behind fence: 180 mm - Max. profiling depth: 35 mm - Axial adjustment 40 mm - Insertion segment: 125 mm 4TH SPINDLE - First upper horizontal spindle - Motor with brake, 7.5 kW - Diameter: 40 mm - Speed: 6,000 rpm - Tool cutting circle: 112–200 mm - Max. profiling depth: 35 mm - Axial adjustment 40 mm - Upper horizontal spindle, pneumatically controlled axially (40 mm) via selector switch, max. saw diameter 200 mm - Split pressure shoe in front of upper spindle, adjustable to tool cutting circle and can be swung away from the tool, spring-loaded - Pneumatic glazing bead discharge after upper spindle, height-adjustable 5TH SPINDLE - Second lower horizontal spindle - Motor with brake, 4.0 kW - Diameter: 40 mm - Speed: 6,000 rpm Hedjyuzczopfx Adkjni - Tool cutting circle: 112–200 mm - Max. profiling depth: 15 mm All profiling spindles are dynamically balanced for high concentric running accuracy Combined control of right spindle (axial), top spindle (axial), and glazing bead discharge FEED SYSTEM - Mechanical feed, steplessly adjustable 5–24 m/min, with brake – 2.2 kW - Infeed roller before 1st lower tool pneumatically controlled "up/down" - Durofer pointed tooth rollers (Weinig patent) with depth limiter and self-cleaning - Feed roller adjustment in relation to left spindle, axial 35 mm MACHINE ELECTRICS - Operating voltage: 400 Volt (range 380–420 Volt), 50 Hz - Electrical design according to DIN VDE 0113, electrical equipment for industrial machines EN60204, IEC-204-1 Further information on request.

Stanje: zelo dobro (rabljeno), Leto izdelave: 1998, DONNÉES TECHNIQUES - Largeur de travail max. : 230 mm - Hauteur de travail max. : 130 mm - 5 broches : 1) broche horizontale inférieure, 230 mm, 4 kW 2) broche verticale droite, 130 mm 3) broche verticale gauche, 130 mm (2ème et 3ème broches), 7,5 kW 4) broche horizontale supérieure, 230 mm, réglable pneumatiquement avant/arrière, 5) broche horizontale inférieure, 230 mm, 4 kW - toutes les broches sont réglables (haut/bas, droite/gauche) - toutes les broches avec frein électrique - 4 rouleaux d’entraînement supérieurs dentés, dont 2 doubles Hnedpfx Asyutyfodkei - 2 rouleaux de sortie supérieurs, caoutchoutés et lisses - avance par arbres à cardan - moteur d’avance : 2,2 kW - pression de service : 6-10 bar - réglage de l’épaisseur de rabotage - lubrification de la table - longueur de la table d’entrée : 1980 mm - diamètre des piquages d’aspiration : 5x140 mm - dimensions (L/l/H) : 4000x1800x1700 mm - poids env. 3300 kg Départ entrepôt - Disponibilité rapide -

Stanje: rabljeno, Leto izdelave: 2009, Max. workpiece length: 4,500 mm Milling spindle: 1 unit Main motor: 20 kW Control: Siemens Model: Weinig Conturex 2 C 114 ----- Working width: 40–260 mm Working height: 25–110 mm 2 x PowerGrip clamp tables, 2 x 2,280 mm ----- Workpiece length: 200–4,500 mm Processing of workpieces exceeding 2,700 mm in length is carried out using a repositioning cycle. Main spindle 1: ----- Motor with brake: 20 kW HSK 63F Speed electronically adjustable: 2,000–18,000 rpm Max. tool length from HSK 63F reference surface: 290 mm With C-axis Tool magazine: ----- Number of positions: 30 Slot spacing: 100 mm Hedpfx Aewunwyodkeni Fixed multi-spindle drilling head ----- For horizontal and vertical drilling and milling operations without tool change ----- Price ex-location Prices for Dismantling and loading onto customer’s truck Transport within Germany and abroad as well as reassembly commissioning and, if required, new profiles available on request! Including used tools (drawings available on request!): ----- Wood: IV 68, 78, 88 in- and outward opening, with fitted weather bar Wood-aluminium: IV 68/68, 78/78, 87/68, 97/78 Lift-and-slide doors IV 68 and 78 Front doors IV 68 and 78 Pivot windows Corner joints: mortise/tenon & dowel Technical data as per manufacturer – no guarantee! Detailed technical description available on request!

Stanje: rabljeno, Cena: Na zahtevo - Posebnosti: - Opis: Vključuje: Približno 260 skobeljnih glav, 5 žagarskih agregatov, 70 rezkalnih glav (Spinner) in vse nože na policah na steni - Dokumentacija na voljo: Ne - CE certifikat prisoten: Ne Hedpsytcvajfx Adkeni Finančne informacije DDV: Navedena cena je brez DDV DDV/obračun po razliki: DDV je odbiten za podjetja Dostava in odkup je možen kadarkoli za vso industrijsko opremo Yorick Diebels

Stanje: rabljeno, Leto izdelave: 2004, skupna širina: 800 mm, skupna dolžina: 1.200 mm, skupna višina: 900 mm, Lastna teža: 100 kg Cena: po povpraševanju - Leto izdelave: 2004 - Dokumentacija na voljo: Ne - CE certifikat na voljo: Ne - Serijska številka: 102851 Hnjdpoytbl Hsfx Adkji - Transportne mere: 1200mm x 800mm x 900mm (d x š x v) - Transportna teža [kg]: 100 kg - Število transportnih paketov [kos]: 1 Finančne informacije DDV: Navedena cena je brez DDV DDV/obdavčitev razlike: DDV je odbiten za podjetja Dostava in možnost odkupa možna kadarkoli za vse iz industrijskega področja. Lukas van Rossum

Stanje: rabljeno, Leto izdelave: 2006, skupna višina: 1.600 mm, skupna dolžina: 1.300 mm, skupna širina: 1.500 mm, Lastna masa: 900 kg Cena: po dogovoru - Leto izdelave: 2006 - Dokumentacija na voljo: Ne - CE-certifikat: Ne - Serijska številka: 108088 - Moč motorja: 1,0 kW - Transportne mere: 1300 mm x 1500 mm x 1600 mm (d x š x v) - Transportna teža [kg]: 900 kg - Št. transportnih paketov: 1 Finančne informacije DDV: Cena je navedena brez DDV DDV/diferencirano obdavčenje: DDV odbit za podjetja Dostava in prevzem v račun možna kadarkoli za vse iz industrijskega področja Hodsytbc Sepfx Adksni Lukas van Rossum

Stanje: zelo dobro (rabljeno), CATALOGUE NUMBER 6575 TECHNICAL DATA - Max. working width: 230 mm - Max. working height: 170 mm - 7 spindles: 1) Lower horizontal spindle: 230 mm, 11 kW 2) Right vertical spindle: 170 mm 3) Left vertical spindle (spindles 2 & 3): 11 kW 4) Right horizontal spindle: 170 mm, 5.5 kW 5) Top horizontal spindle: 230 mm, 11 kW 6) Lower horizontal spindle: 230 mm, 7.5 kW 7) Universal spindle: 230 mm, 360° adjustable, 7.5 kW - All spindles adjustable up/down, right/left - Spindles 3 and 5 electrically adjustable - ATS system - Spindle diameter: 40 mm - Electric brakes - Top feeding: 4 geared infeed rollers (incl. 1 double), 1 double rubber infeed roller, 1 double rubber outfeed roller - Bottom feeding: 2 smooth steel feed rollers, 1 double rubber feed roller - Feed on Cardan shafts - Pneumatic pressure on feed rollers - Variable feed speed adjustment: 6–24 m/min - Feed motor: 5.5 kW - Electric thickness adjustment - Table lifting motor: 0.55 kW - Centralised table lubrication - Extraction ports diameter: 7x140 mm - Dimensions (LxWxH): 5800 x 2050 x 1850 mm - Weight: approx. 4500 kg FEATURES – German-made, WEINIG brand Hnjdpfx Asyr Ry Dodkoi – 7-head planer – Universal spindle – Equipped with ATS – Suitable for both wet and dry wood – Used planer in very good condition Net price: 159,900 PLN Net price: 38,070 EUR Net price calculated at exchange rate 4.2 PLN/EUR (Price may change subject to significant exchange rate fluctuations)