TRAUB TNX 65/42

TRAUB TNX 65/42

Stanje: rabljeno, Leto izdelave: 2007, Premer obdelovanca 275 mm Dolžina obdelovanca 900 mm Nadzorna enota TRAUB TX8i-s Premer vretena 65 mm Število vrtljajev vretena – brezstopenjsko 1 – 5.000 vrt/min Premer vretena v sprednjem ležaju 110 mm Os C 1 – 500 vrt/min Os X 175 mm Os Z 650/975 mm Os Y +/- 40 mm Hitrost pri hitrem premiku X/Y/Z 20 / 40 / 20 m/min Potisna sila X/Y/Z 5,5 / 5,5 / 10 kN Revolver za orodja – število postaj 10 Število pogonjenih orodij 10 Število vrtljajev orodja 1 – 6.000 vrt/min Knsdpfx Ahszwg Ndsceb Moč pogona 25 % ED 5,50 kW Navor pri 25 % ED 17,50 Nm Nastavek za orodje DIN 69880 Ø30x55 Premer vretena v sprednjem ležaju 110 mm Skupna potrebna moč 95,00 kW Teža stroja približno 16,00 t Potrebna površina približno 10,00 x 3,50 x V3,00 m

Stanje: novo, Leto izdelave: 2024, Funkcionalnost: popolnoma funkcionalen, pritisk: 16 letvica, vhodna frekvenca: 50 Hz, vrsta vhodnega toka: trifazni, temperatura: 400 °C, vhodna napetost: 6.000 V, vrtljajska hitrost (min.): 1.500 obr/min, največja hitrost vrtenja: 1.500 obr/min, vrsta hlajenja: zrak, Industrial Steam Turbogenerator Howden – Model KK&K TWIN CA46, NEW, never installed or commissioned, still under manufacturer’s warranty. Due to a revision of long-term industrial strategy, an industrial Howden KK&K TWIN CA46 steam turbogenerator, complete according to original OEM supply, is available for sale. The unit is BRAND NEW, entirely manufactured and tested at OEM level, but has never been installed or put into service. It remains covered by the manufacturer’s warranty and is stored in a closed, controlled environment. Immediate availability eliminates the standard lead time, which for this class of equipment is typically 24–36 months. Main scope of supply: - Steam turbine on skid with integrated gearbox - Synchronous generator supplied separately Turbine technical configuration: - Model: KK&K TWIN CA46 - Double-casing turbine (Steam Part A + Steam Part B) - Integrated 3-shaft gearbox (2 pinions + central wheel) - Controlled steam extraction between HP and LP sections (included) Key design conditions: - Inlet steam pressure (HP): 16 bar(a) - Inlet steam temperature: 400 °C - Electrical output at terminals: up to 1,595 kW - Rated speed: 1,500 rpm Electrical generator: - Three-phase synchronous generator - Rated power: 1,994 kVA - Voltage: 6 kV – Frequency: 50 Hz - Cooling: IC31, air Knjdpfx Aeyidvdshcob - Brushless design, ready for grid-parallel operation Included systems: - Integrated base-mounted oil system - Main mechanical oil pump and auxiliary electric pump - Local control panel on skid - Control and protection panel with Siemens SIPROTEC 5 - Electronic speed and pressure governor - Independent overspeed protection device - ENC-RfG turbogenerator simulation model Typical applications: - Industrial cogeneration plants - Process steam energy recovery - Biomass and waste-to-energy facilities - Combined generation of electric power and process steam Condition and status: - Condition: NEW - Manufacturing year: late 2024 - Never installed – never commissioned - Still under manufacturer’s warranty - Complete OEM technical documentation available - Installation and commissioning possible with OEM support Possible application fields: - Biomass and waste-to-energy plants for the production of electric power and process steam, with immediate unit availability and no multi-year production lead times - Industrial cogeneration (CHP) in facilities with continuous process steam consumption (paper, food, chemical, manufacturing industries) - Revamping/repowering of existing plants as a rapid alternative to new OEM units with 24–36 month lead times Price: on request. Further technical details and documentation available upon request.

Stanje: dober (rabljeno), Leto izdelave: 2009, Funkcionalnost: popolnoma funkcionalen, CNC Lathe TRAUB TNX 65/42 Year of Manufacture: 2009 Control System: Traub TX 8i-s TECHNICAL DATA - Number of spindles: 2 - Number of axes: 12 - Number of turret heads: 2 MAIN SPINDLE - Spindle nose: A2-6 - Spindle drive power: 24 kW - Spindle speed: 5,000 rpm - Max. bar diameter: 65 mm - Max. main spindle chuck diameter: 175 mm - Minimum C-axis resolution: 0.001° SUB SPINDLE - Spindle nose: A2-5 - Spindle drive power: 28 kW - Spindle speed: 7,000 rpm - Max. bar diameter: 42 mm - Minimum C-axis resolution: 0.001° - Travel distance: 700 mm LEFT UPPER TURRET - Number of positions: 10 - Number of driven positions: 10 - Travel X/Z: 175 / 650 mm - Travel Y: +/- 40 mm - Tool type: VDI 30 - Driven tool speed: 6,000 rpm - Driven tool power: 5.5 kW RIGHT LOWER TURRET - Number of positions: 10 - Number of driven positions: 10 - Travel X/Z: 175 / 650 mm - Travel Y: +/- 40 mm - Tool type: VDI 30 - Driven tool speed: 6,000 rpm - Driven tool power: 5.5 kW ELECTRICAL SUPPLY - Supply voltage: 400 V - Total power consumption: 95 kW WEIGHT AND DIMENSIONS - Footprint: 5,450 x 2,318 mm - Machine height: 2,258 mm - Machine weight: 10,000 kg New spindle installed since 04/26 ACCESSORIES - 3-color status lamp Kodpfx Aeyw H Szshcjnb - Coolant tank: RESY * with high-pressure pump * with paper filter - Chip conveyor - Parts ejector - Parts belt conveyor

Stanje: zelo dobro (rabljeno), Leto izdelave: 2013, premer nad prečnim suportom: 360 mm, maksimalni premer struženja: 366 mm, maksimalna dolžina struženja: 705 mm, prehod pre palico: 80 mm, hitrost vretena: 4.000 o/min, hitrost rezkanja: 10.000 o/min, moč glavnega vretena: 18,5 kW, os C: 0,001 stopinje, os Y: -/+ 50 mm, revolverska glava s 12 postajami. Mori upravljanje M730BM, opremljen z merilcem orodja, transporterjem odrezkov, trivrato vpenjalno glavo, pobiralnikom delov, podajalnikom palic. Kodpfx Aex Eitushcjnb

Stanje: rabljeno, Zasuk nad ležiščem 400 mm Zasuk nad sani 350 mm Razdalja med konicama 610 mm Maks. dolžina pomika 560 mm Maks. prečni pomik 40+120 mm Knjdpfx Asxg Nd Aohceb Vretenove vrtljaje 40-4000 o/min Premer vrtine vretena 52 mm Revolver z 12 postajami Krmiljenje: Fanuc 6T Opremljen z: Glejte fotografije

Stanje: dober (rabljeno), Leto izdelave: 2017, Pomiki X Y Z: 1067 mm x 610 mm x 610 mm, Velikost mize: 1270 mm x 610 mm, 600 mm C-osna miza (360 stopinj) Glava +/- 90 stopinj (B-os), 37 kW motor vretena, Knedpezh Nczofx Ahcob Avtomatski izmenjevalec orodij s 40 mesti (stranska roka), Stožec vretena DIN 40, Vreteno 12.000 vrt/min, Krmilnik Hurco Winmax 5, Hladilna tekočina skozi vreteno, transporter odrezkov, sonda za vreteno.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2006, x-travel 750 mm y-travel 210 mm Knedpfx Ahjy Spuuecob z-travel 1150 + 100 mm Control Fanuc MSX-701III Maximum turning diameter: 660 mm Maximum turning length: 1498 mm Swing diameter over cross slide: max. 400 mm Spindle speed: 3000 rpm Tool magazine with 40 stations Turret with 10 positions Total connected load: 90 kVA Machine weight approx. 26.6 t Space required approx. 5301 x 2997 x 2788 mm Capacity: Swing diameter over cross slide (Tool spindle 1): 750 mm Swing diameter over cross slide (Turret 2): 400 mm Max. turning diameter (Tool spindle 1): 660 mm Max. turning diameter (Turret 2): 275 mm Max. machined workpiece length: 1498 mm Max. bar material: 90 mm Axes travels: X1 axis (tool spindle): 750 mm Y axis (tool spindle): 420 (+/- 210) mm Z1 axis (tool spindle): 1635 + 100 mm for tool change B axis (tool spindle): +/- 120°, full B-axis 1° indexed and 0.0001° clamped X2 axis (turret): 195 mm Z2 axis (turret): 1525 mm SZ axis (sub spindle): 1610 mm Rapid traverses: (X1, Z1) 50 m/min., (Y, X2, Z2, SZ) 30 m/min. Main and sub spindle: Infinitely variable spindle speeds (Spindle 1 + 2): 30-3000 rpm C-axis (Spindle 1 + 2): 0.001° Main spindle motor: 22/18.5 kW Sub spindle motor: 22/18.5 kW Torque (Spindle 1 + 2): 1000 Nm Disc turret: Number of tool stations: 10 Speed of driven tools: 6000 rpm Drive power: 5.5/3.7 kW Milling spindle: Tool holder: HSK A63 Max. speed: 12000 rpm Drive power: 18.5/11 kW Torque: 120/44 Nm Tool changer: 40 positions Tool diameter: 70/140 mm Tool length: 400 mm Tool weight: 8/10 kg Total connected load: 90 kVA Overall dimensions (L x W x H): 5301 x 2997 x 2788 mm Machine weight: 26.6 t Equipment/Accessories: - Upper milling spindle (B-axis), full 4th axis, positioning 0.0001° - 40-position tool magazine - Lower 10-position turret, all positions driven - 2 x 3-jaw quick change chuck KNCS-N 315/91 - KNOLL high-pressure coolant system, pressure selectable 12/25/35/45/55/62 and 72 bar, with maintenance-free rotary filter unit - Chip conveyor - Blow-off system for main spindle chuck (M-function control) - Blow-off system for tool cutting edge (M-function control) - Coolant gun incl. accessories - Oil mist extraction - Direct measuring system for X1, X2, Y axis - Bar feeder interface - Dual foot switch for both spindles - Islands and pockets programming for MAPPS - High speed fixed cycle for MAPPS - Program memory extension to 8 MB - Program restart - 3-stage signal lamp - Memory card 512MB (CF Card) - Measuring arm (image) for tool measurement in machine - Tool holder + case, reduction sleeves, driven tools - Jaw set - Collet set

Stanje: dober (rabljeno), Leto izdelave: 2007, Funkcionalnost: popolnoma funkcionalen, premer struženja: 545 mm, največja hitrost vretena: 12.000 obr/min, potovalna razdalja osi X: 410 mm, pomik osi Y: 140 mm, pomik po osi Z: 570 mm, Oprema: transportni trak za ostružke, MAZAK Integrex 100-IV je kompaktno in izjemno natančno CNC-obdelovalni center za struženje in frezanja, ki je zasnovan za celovito obdelavo kompleksnih obdelovancev v eni namestitvi. Zahvaljujoč kombinaciji funkcij struženja in frezanja ter integrirani B- in Y-osi je stroj še posebej primeren za zahtevne natančne komponente v medicinski tehniki, strojni industriji in finomehaniki. Stroj je bil izdelan leta 2007 in je opremljen z zmogljivo krmilno enoto MAZATROL Matrix. Ta omogoča tako interaktivno kot tudi programiranje v skladu s standardom ISO ter ponuja sodobne funkcije za učinkovito in produktivno proizvodnjo. Tehnični podatki na kratko: Kjdpjzpyvhjfx Ahcenb Hod poti znaša 410 mm v osi X, 140 mm v osi Y (±70 mm) in 570 mm v osi Z. Osi B ima območje nihanja 225°, kar omogoča kompleksno obdelavo na 5 straneh. Os C glavne vretena deluje z visoko natančnostjo pozicioniranja 0,001°. Največji premer struženja in vrtanja znaša 545 mm. Glavna vretena dosega hitrosti do 6.000 vrt/min pri moči približno 11 kW, kar omogoča dinamično in natančno struženje. Integrirana vretena za frezanja deluje s hitrostmi do 12.000 vrt/min pri moči približno 5,5 kW in je odlična za operacije frezanja, vrtanja in navojčkov. Stroj ima menjalnik orodij (na voljo) z največjo dolžino orodja 210 mm in držalo orodja KM, ki zagotavlja visoko togost in hitro menjavo orodij. Oprema: Oprema vključuje: • transporter za odvoz stržkov • sistem za merjenje orodja „Tool Eye“ Z maso stroja približno 5.040 kg, Integrex 100-IV prepriča s svojo kompaktno zasnovo, visoko natančnostjo in prilagodljivostjo – idealen za gospodarno celovito obdelavo v sodobnih proizvodnih okoljih. Pri nas ste v dobrih rokah – strokovno, zanesljivo in s strastjo do strojev! PS CNC Service Germany GmbH & Co. KG Vse informacije so brez garancije.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2020, Pomiki XYZ: 610 x 406 x 406 mm, miza premera 400 mm, največja obremenitev mize 226 kg, Kodpfx Ahozg Enqsconb nagib mize +120°, -35°, 22,4 kW, 10.000 vrt/min, BT40, 30-postajni menjalec orodij, hladilna tekočina, transporter odrezkov

Stanje: dober (rabljeno), Leto izdelave: 2005, obratovalne ure: 32.870 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 6030578, premer struženja: 32 mm, največja hitrost vretena: 8.000 obr/min, Premer palice (maks.): 32 mm, We offer for sale a Traub TNL26K CNC automatic lathe. The machine is connected to power and can be inspected in operation by prior appointment. Year of manufacture: 2005 Kedpevldx Aefx Ahcjnb Spindle bore: 32 mm Main spindle: 6.7/10.7 kW; 8000 rpm Counter spindle: 6.7/10.7 kW; 8000 rpm Upper turret: 12 positions, 12x12/16x16 mm, driven tools 2/5.5 kW, 0-6000 rpm, 6.4/21 Nm Lower turret: 12 positions, 12x12/16x16 mm, driven tools 2/5.5 kW, 0-6000 rpm, 6.4/21 Nm Connected load: 24 kW Bar feeder: FMB Turbo 5-42/4200 mm Swarf conveyor: Knoll 240 S1/100 Coolant compact band filter: Resy The machine comes with a large number of stationary and driven tool holders – please see the attached photo for a complete list.