Stroj za globoko vrtanje Mollart - LD8 - 150

Mollart LD8 150 Pellet Die

Stanje: rabljeno, Leto izdelave: 1961, Premer obdelovanca - maks. 100 mm Premer obdelovanca - min. 10 mm Dolžina obdelovanca 1000 mm Skupna potrebna moč 16 kW Lhsdpfowwl I Ijx Aqcjl Teža stroja cca 3 t Potrebni prostor cca 0 m Vodila so bila obnovljena pred 10 leti.

Stanje: rabljeno, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of Manufacture: 2007 Rolling Force: max. 24 tons Tool Diameter: max. 270 mm Roll Spindle Diameter: 69.85 mm Tool Bore Diameter: 70 mm (nominal diameter) Mounting Length, Tool Length: max. 180 mm Workpiece Diameter: max. 50 mm Hydraulic Motor Power: 3 kW Roll Drive Motor Power: approx. 5.5 kW Mains Connection: 400 Volt, 50 Hz, 10 kW - Pivoting roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gear shift - Hydraulic system integrated in machine frame - Operating manual with electrical diagram Space requirements (L x W x H): 2000 x 1450 x 190 mm Weight: approx. 3 tons Very good condition Plunge rolling: The thread rolling dies, with the same pitch as the workpiece, form the thread by pressing into the workpiece up to the nominal diameter. The thread length is at most as long as the width of the rolling dies. Lhedpfouz If Njx Aqcsl Through-feed rolling: Used when the thread length exceeds the width of the rolling dies. Through-feed dies have three functional zones – lead-in, calibration, and lead-out. Knurling Rolls: These rolls have no pitch and are swiveled at the pitch angle of the profile to be rolled. Pitch Rolls: Pitch rolls have a profile with a pitch, differing from knurling rolls. The sum of the pitch angle and swivel angle determines the pitch angle in the finished workpiece.

Stanje: rabljeno, Leto izdelave: 2005, Swing diameter: 275 mm Turning length: 900 mm Control: TRAUB TX8i Spindle bore: 65 mm Drive power 100% duty cycle: 25.20 kW Drive power 40% duty cycle: 30.20 kW Torque at 40% / 100% duty cycle: 180 / 135 Nm Spindle speeds - stepless: 1 - 5,000 rpm Spindle diameter at front bearing: 110 mm C-axis: 1 - 500 rpm Tool carrier No. 1 X-axis: 290 mm Y-axis: 165 mm Z-axis: 600/950 mm B-axis: 360° Rapid traverse X/Y/Z: 18 / 18 / 30 m/min Feed force X/Y/Z: 10 / 10 / 7 kN Number of tools: 2x2 + 2x2 Number of driven tools: 2x2 + 2x2 mm Tool speeds: 8,000 / 2,000 rpm Drive power 25% duty cycle: 5.80 kW Torque at 25% duty cycle: 4x18.6 / 4x74 Nm Tool holder: TRAUB Ø60 Tool carrier No.2 / No.3 / No.4 X-axis: 170 mm Z-axis: 600/950 mm Y-axis: +/- 60 mm Rapid traverse X/Y/Z: 18 / 15 / 30 m/min Feed force X/Y/Z: 10 / 10 / 7 kN Tool turret - number of stations: 10 Number of driven tools: 10 mm Tool speeds: 1 - 6,000 rpm Drive power 25% duty cycle: 5.80 kW Torque at 25% duty cycle: 18.60 Nm Tool holder: DIN 69880 Ø40x63 Bar loading magazine: DNH61 / 3000 Bar lengths: 1,000 - 3,200 mm Ledpfx Asw E Nnbsqcjhl Bar diameter: 18 - 63 mm Hexagon max.: 45 mm Total connected load: 95.00 kW Machine weight approx.: 16.00 t Space requirement approx.: 10.00 x 3.50 x H3.00 m With TRAUB TX8i control, main and counter spindle with C-axis, 3 pcs. turret tool carriers, 1 pc. vertical tool carrier with B-axis, extraction system, chip conveyor, coolant unit with coalescence separator. Bar loader: TRAUB Stamag DNH61 / 3000 2 pcs. 3-jaw chucks SMW KNCS-N 170-43 2 pcs. HAINBUCH Spanntop chucks 40 pcs. various static tool holders 6 pcs. various driven tool holders Spare parts package Machine can be inspected under power.

Leto izdelave: 1995, stanje: rabljeno, številka stroja/vozila: 18891, Tractive force: 10 t. Lhsdpobrcmkjfx Aqcel Lift: 1000 mm 3 clearing stations With chip conveyor + platform for above-floor installation and safety door.

Stanje: dober (rabljeno), Leto izdelave: 2008, Funkcionalnost: popolnoma funkcionalen, Proizvodna linija proizvajalca Brunette iz Kanade, ki jo odlikujeta izjemna moč in vzdržljivost. Ponudba vključuje luščilec hlodovine z dovodnimi mizami, transporterje za odvoz skorje ter sekalnik z instalirano močjo 630 kW in dvojnim polžastim izpraznjevalnim transporterjem. Lhjdpsvu D Dwofx Aqcel

Stanje: zelo dobro (rabljeno), Leto izdelave: 2001, obratovalne ure: 4.500 h, Funkcionalnost: nepreverjeno, številka stroja/vozila: 090119, Country of manufacture: CE – Germany Voltage: 400V Net weight: 7,500 kg Dimensions: 2.9 x 2.3 x 2.3 m Operating hours: 29,731 h – Working hours: 4,500 h TECHNICAL DATA AXES Maximum travel X-axis: 400 mm Maximum travel Y-axis: 300 mm Maximum travel Z1-axis: 475 mm Maximum travel Z2-axis: 475 mm Rotational range B-axis: 0.0001 – 360° Rotational range C1/C2-axis: 0.0001 – 360° Lhjdpjht Hg Dsfx Aqcel WORKPIECE Maximum cubic dimension: 80 x 80 x 80 mm Maximum weight: 5 kg TURRET HEAD Number of stations: 24 Number of driven stations: 18 Number of static stations: 6 Maximum tool holder (round): Ø 20 mm Maximum tool holder (square): 16 x 16 mm (20 x 20) Maximum turret head path above tool tip: 500 mm Speed of rotating tools: 1–9,000 rpm SPINDLE Maximum speed: 6,000 rpm Maximum bar diameter: Ø 42 mm Maximum clamping chuck diameter: 140 mm BAR MACHINING Maximum bar length for bar feeder: 1,000 mm Maximum workpiece size for bar gripper: Ø 42 x 100 mm Maximum diameter for collet gripper: 42 mm Clamping cylinder pull/push force: 20,000 N FEED DRIVES Feed force X-axis: approx. 895 daN Feed force Y-axis: approx. 895 daN Feed force Z1-axis: approx. 895 daN Feed force Z2-axis: approx. 895 daN Rapid traverse X/Y/Z axes: 20 m/min Tool control motor torque: 2.4 Nm Spindle S1 / Spindle S2: 70 Nm COOLING (Performance rate) Chip conveyor submersible pump output: approx. 10 l/min at 4.5 bar      80 l/min at 3.2 bar      150 l/min at 0.7 bar High-pressure pump (in conveyor): 10 l/min at 13.2 bar      50 l/min at 9 bar      90 l/min at 1 bar Lubrication volume in chip conveyor: approx. 134 L Coolant volume in cooling unit: 45 L CONTROLLER: Siemens 840D WORKING PRECISION Resolution X/Y/Z: 0.1 µm Resolution B-axis: 0.0001° Resolution C-axis: 0.0001° Positioning accuracy: 5 µm Repeatability: 0.6 µm Max. runout error: 0.5 µm ELECTRICAL Spindle 1 / Spindle 2 (at 100%): 11 kW Spindle 1 / Spindle 2 (at 40%): 15 kW Feed motor X/Y/Z1/Z2: 1.3 kW B-axis: 1.3 kW Tool control: 2.3 kW Hydraulic pump: 7.5 kW Hydraulic return: 0.75 kW Cooling unit fan 1 / 2: 0.18 kW Cooling unit circulation pump: 1.1 kW Cooling unit compressor: 2.2 kW Chip conveyor: 0.25 kW Emulsion pump 1: 1.1 kW Emulsion pump 2: 2.2 kW Control voltage: 400 V Network frequency: 50Hz (60 optional) Control voltage: 24V DC Total power: 35 kW Nominal current: 63A Connection: TM / TT / IT grid PNEUMATICS Maximum operating pressure: 10 bar Normal operating pressure: 6 bar Minimum operating pressure: 5 bar Air output: approx. 150 L/min Valve voltage: 24V DC Oil mist tank capacity: 12 L Quality standard: 2 according to Pneurop6611 NOISE EMISSION Normal operation: 78–80 dB Technical data subject to change; errors and omissions excepted Inventory No. 2321018; machine configuration: - Chip conveyor - Prepared for bar feeder installation Tool holders: - 6 fixed drill holders ER32 - 8 turning tool holders - 5 powered tool holders ER32 - 4 powered tool holders ER25 - 6 powered tool holders ER20

Stanje: dober (rabljeno), globina vrtanja: 1.500 mm, dolžina podajanja os X: 2.000 mm, dolžina pomika po osi Y: 1.300 mm, dolžina podajanja os Z: 1.500 mm, Manufacturer: TBT Tiefbohrtechnik Model: BW 250-S Control: SIEMENS 840D Year of manufacture: 2007 Drilling, milling, and tapping machine for heat exchanger bases and plates Swiveling A-axis: +25° to -15° Filtration and coolant system: 1,000 L Chip conveyor: 2,000 x 1,200 mm – output height Milling tool changer, tower station, 20 positions ELB drilling capacity: 3 – 35 mm Milling capacity: 250 cc/min Lhodpfxov A Uw Ds Aqcsl Feed rates on all axes (X-Y-W-Z): 15,000 mm/min Approx. 15,000 spindle hours Comes with a large tooling package Specifications Metric / US Standard Max. drill diameter (steel): 40 mm Drilling depth: 1,500 mm X-axis travel: 2,000 mm Y-axis travel: 1,300 mm Z-axis travel: 1,500 mm W-axis travel: 750 mm Table load capacity: 15,000 kg Table dimensions (L x W or Ø): 1,600 x 1,200 mm Spindle taper: HSK 63 Mk Spindle power: 11 kW Spindle speed: 8,000 rpm Dimensions (approx.): Length: 7,200 mm Width: 7,800 mm Height: 4,250 mm Weight: 23,000 kg Please note: The information on this page has been provided by us and, where possible, obtained from the manufacturer to the best of our knowledge. The information is given in good faith, but accuracy cannot be guaranteed. Therefore, they do not constitute representations or contractual terms. We recommend verifying all critical details.

Stanje: rabljeno, Razdalja med konicami: 2.500 mm Višina konice: 250 mm Premer brusnega koluta: 600 mm Skupni pomik brusne podpore: 320 mm Število obratov vretena obdelovanca: 50 - 450 obr/min Vpenjanje: MK5 Konica konjička: MK Cilindrični brusilni stroj | NAXOS-UNION - W-500 Lhjdox Avtcepfx Aqcel Cilindrični brusilni stroj je bil leta 2017 popolnoma obnovljen (RETROFIT) pri KPS-Schleiftechnik (glej potrdilo naročila). Stroj je dobro vzdrževan. Za dodatne tehnične informacije glejte ponudbo.

Stanje: dober (rabljeno), Leto izdelave: 2002, Premer obdelovanca: 40 mm Modul – maks. 2 Modul – min. 0,1 Dolžina obdelovanca – maks. 665 mm Teža: 4,5 t Premer vrtine vretena: 30 mm Krmilni sistem: Siemens Premer ležaja rezkala: 20 mm Skupna potrebna moč: 5,5 kW Tehnični podatki Maks. modul: 2 Izhod: 0,5 – 25 mm Število prestav: večstopenjsko / večkratno Maks. premer obdelovanca: 40 mm Maks. dolžina obdelovanca: 180 mm Premer rezkala: maks. 80 mm Ledsv Ucdvepfx Aqcehl Maks. širina rezkala: 12 mm Os Z (dolžina reza z nasprotno konico): 90 mm Os Z (dolžina reza brez nasprotne konice): 113 mm Kot nagiba rezkalne glave: 30° / 30° Opis Stroj za oblikovanje zobnikov in rezkanje navojev. LAMBERT – 124 CNC Stroj je v dobrem stanju.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 17004A, Premer palice (maks.): 20 mm, Naprodaj: dve popolnoma delujoči stružnici Tsugami HS20M 5-axis. Vse je v delujočem stanju, stroja sta bila nedavno servisirana in tehnično pregledana. Vključeno: Lhsdpfx Aqsyghcrocjl – različni nosilci orodij, – popolna tehnična dokumentacija. Stroja sta bila v glavnem uporabljena za proizvodnjo zobnih implantatov in sta bila kupljena na Švedskem. Če vas zanima, kontaktirajte me za dodatne podrobnosti, fotografije, ceno ali za dogovor o ogledu.