Centrica Business Solutions Mtu 12V4000 L33 nakup rabljenega (9.002)

Stanje: rabljeno, Leto izdelave: 2023, Funkcionalnost: nepreverjeno, številka stroja/vozila: MTU 12V4000 L33, vrsta vhodnega toka: trifazni, skupna višina: 5 mm, skupna dolžina: 25 mm, skupna širina: 3 mm, vrsta hlajenja: voda, Oprema: dokumentacija / priročnik, vrtilna hitrost brezstopenjsko nastavljiva, Installed system never put into operation Cogeneration Unit GAS GENERATOR SET MTU 12V4000 L33 Condition: New – 0 hours Housing: Enclosed container Rated electrical power: 1,262 kW Thermal power: 1,355 kW Electrical efficiency (cos φ = 1.0): 42.1% Thermal efficiency: 45.2% Total efficiency (with full heat utilization): 87.3% Fuel consumption: • at 100% load: 299 Nm³/h • at 75% load: 232 Nm³/h • at 50% load: 167 Nm³/h Manufacturer: MTU – Centrica Business Solutions Srl Equipment designation: Type: E1265 250 Nox L33 Natural Gas CHP Unit Configuration: Containerized Rated current: 1,935 kVA Engine: Genset Rolls-Royce MTU 12V4000L33 Number of cylinders: V12 Maximum engine output: 1,320 kW Generator: Stamford Model: PE734E-312 Type: three-phase, synchronous, brushless, four-pole Nominal voltage: 400 V Frequency: 50 Hz Dimensions (L x W x H): 12,800 x 2,700 x 2,900 mm Absorption Chiller Unit CARRIER 16LJ-F41 Condition: New – 0 hours Housing: Enclosed container Capacity: 1,178 kW Cooling System Flow rate: 56.4 L/sec Pressure: 45 kPa Dkedpfx Aeydqlqopljl Connection (DIN): 8” (inch) Retention: 0.48 m³ Cooling System Flow rate: 93.1 L/sec Pressure: 117 kPa Connection (DIN): 10” (inch) Retention: 1.39 m³ Dimensions (L x H x W): 5,330 x 3,080 x 1,690 mm Weight: 13,700 kg Evaporative Cooling Towers: No. 2 Condition: New – 0 hours

Stanje: rabljeno, Leto izdelave: 2008, Na prodajo ponujamo MTU kogeneracijsko enoto z nazivno električno močjo 1,2 MW. Tehnični podatki: Proizvajalec: MTU Motor: MTU 12V4000L62 Generator: Stamford Dsdpfsxcwlasx Aplskl Leto izdelave: 2008 (generalno obnovljen leta 2015) Delovnih ur: 63.000 Vključno z elektro omarami Vključno z miznim hladilnikom

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, vrsta goriva: plin, moč: 1.521 kW (2.067,98 KM), izhodna napetost: 400 V, izhodna frekvenca: 50 Hz, največja hitrost vrtenja: 1.500 obr/min, proizvajalec motorjev: MTU, 10 kosov na zalogi =Obseg dobave= Agregat mtu 12V4000L64FNER, 400 V, za obratovanje na zemeljski plin. Plinska proga s tlakom na vstopu 116-250 mbar z 1-metrsko gibljivo cevjo iz gume z jekleno ojačitvijo. Komplet sylomer trakov za namestitev agregata na temelje. Komplet gibljivih priključkov za hladilni krog motorja s prirobničnim priključkom. Komplet gibljivih priključkov za hladilni krog mešanice s prirobničnim priključkom. Komplet izpušnih mehov s prirobničnim priključkom in spojno prirobnico. Komplet brez-vzdrževalnih zagonskih akumulatorjev, nameščenih na osnovnem ogrodju. MIP (MTU Interface Panel) vključno z možnostjo Black Start in vmesnikom za daljinsko upravljanje ECU. =Tehnične specifikacije= Dobavni rok – na zalogi Tip motorja – mtu 12V4000L64FNER Električna moč – 1521 kW Hitrost motorja – 1500 vrt/min Električni izkoristek – 43,9 % Skupni izkoristek – 88,6 % Tip alternatorja – Leroy Somer LSA 53.2 VL6 Napetost – 400 V Djdpey Hcvbsfx Apljkl Frekvenca – 50 Hz < 500 mg NOx pri 5 % O2 =Druge informacije= Država proizvodnje – Nemčija

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, moč: 1.521 kW (2.067,98 KM), vhodna napetost: 400 V, V ponudbi, nova Znamka: Mtu Tip: 12v 4000 gs l64 FNER Leto izdelave: 2025 Moč: 1521 kW Napetost: 400V 50Hz Obratovalne ure: 0 Z garancijo proizvajalca Obseg dobave: - agregat - plinska rampa - MMC krmilna plošča Djdoy Hivuepfx Apljkl

Stanje: novo, Leto izdelave: 2024, NOV stroj, nikoli uporabljen!!! DN SOLUTIONS PUMA 5100LMB Leto izdelave 2024 Os C z gnanim orodjem Upravljanje FANUC OiF touch Vpenjalna glava 21 palcev (535mm) Premer vretena 166mm Pomiki: X-362mm Z-2155mm Maksimalna dolžina struženja 2.002mm Maksimalni premer struženja 650mm Revolver z 12 pozicijami BMT 75 Izmetnik ostružkov Knoll Dedpfsy H D Ufex Aplokl

Leto izdelave: 2022, stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: SPE-Spero-LTX-340, Naprava je bila uporabljena za raziskovalne namene, SPE-Spero-LTX-340, MIR-mikroskop s funkcijo »Hyper Spectral Imaging« (spekter 1900 do 950 1/cm). Izboljšano LowMag lečo 4,0X; NA:0,3, 2,0 mm vidno polje. Ekskluzivno IR-transmisijsko delovanje. Širokopasovna mikrobolometerska kamera 480*480 pikslov. Vključuje visoko natančno avtomatizirano mizico (< 1 μm ponovljivost) in hitro zbiranje podatkov, joystick, nadzorni računalnik, Win10. „Discrete Frequency IR-Imaging“ v realnem času. 2000 ur/1 leto garancije. SPE-Spero-LT-EXT-WAR-12-2000. Nova cena: 240.102 evrov. Prodaja brez garancije, kot je vidno. Dedpjyxc Twsfx Aplokl

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, vrsta goriva: plin, moč: 2.539 kW (3.452,08 KM), izhodna napetost: 400 V, izhodna frekvenca: 50 Hz, skupna dolžina: 6.600 mm, skupna širina: 2.000 mm, skupna višina: 2.300 mm, največja hitrost vrtenja: 1.500 obr/min, proizvajalec motorjev: MTU, =Lieferumfang= 2 x Stromerzeuger mtu 20V4000L64FNER, 400 V für den Betrieb mit Erdgas. Dkodpfx Apjy Hddmolel 2 x Gasstrecke für einen Eingangsdruck von 116–250 mbar mit 1 m flexiblem Gummi-Metall-Anschlussschlauch. 2 x Satz Sylomer-Streifen zur Fundamentmontage der Stromaggregate. 2 x Satz flexible Anschlüsse für Kühlmittelkreislauf des Motors mit Flanschverbindung. 2 x Satz flexible Anschlüsse für Gemischkühlmittelkreislauf mit Flanschverbindung. 2 x Satz Abgasbälge mit Flansch und Gegenflansch. 2 x wartungsfreie Starterbatterien, auf dem Grundrahmen montiert. 2 x MIP (MTU Interface Panel) inkl. Black-Start-Option und Schnittstelle für Fernsteuerung des Motorsteuergeräts (ECU). =Technische Daten= Lieferzeit – ab Lager Motortyp – mtu 20V4000L64FNER Elektrische Leistung – 2539 kW Motordrehzahl – 1500 U/min Elektrischer Wirkungsgrad – 43,9 % Gesamtwirkungsgrad – 88,6 % Generator-Typ – Leroy Somer LSA 54.2 L14 Spannung – 400 V Frequenz – 50 Hz < 500 mg NOx bei 5 % O2 =Weitere Informationen= Transportmaße (LxBxH) – 6,6 x 2 x 2,3 m Herstellungsland – Deutschland

Stanje: novo, Leto izdelave: 2024, Funkcionalnost: popolnoma funkcionalen, vrsta goriva: dizel, moč: 2.520 kW (3.426,24 KM), izhodna napetost: 400 V, izhodna frekvenca: 50 Hz, neprekinjena moč: 2.520 kW (3.426,24 KM), neprekinjena (navidezna) moč: 3.150 kVA, skupna dolžina: 5.760 mm, skupna širina: 1.810 mm, skupna višina: 2.350 mm, največja hitrost vrtenja: 1.500 obr/min, =Obseg dobave= Agregat mtu 20V4000 DS3100 brez hladilnika 400 V Agregat mtu 20V4000 DS3100 brez hladilnika 11 kV Dsdoy Hddaopfx Aplokl =Tehnične specifikacije= Dobavni rok – na zalogi Tip motorja – 20V4000G24F Električna moč – 2520 kW Hitrost motorja – 1500 obr/min Skupna učinkovitost – 80 % Tip alternatorja – Leroy Somer LSA 53.2 M9 / Leroy Somer LSA 53.2 ZL14 Napetost – 400 V / 11 kV Frekvenca – 50 Hz =Druge informacije= Transportne dimenzije (DxŠxV) – 5,76x1,81x2,35 m Država proizvodnje – Nemčija

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2022, največja hitrost vretena: 6.000 obr/min, potovalna razdalja osi X: 205 mm, pomik po osi Z: 560 mm, moč vretenovega motorja: 15.000 W, skupna višina: 1.693 mm, skupna širina: 1.595 mm, skupna masa: 3.600 kg, proizvajalec krmilnikov: FANUC, model krmilnika: 0i PLUS, največja dolžina izdelka: 2.805 mm, število osi: 3, This 3-axis DN Solutions LYNX 2100LMSA was manufactured in 2022. It offers a maximum turning diameter of 300 mm and a turning length of 510 mm. The machine features a 6-inch chuck, a 12/24-position turret, and a sub-spindle for enhanced capabilities. If you are looking for a high-quality CNC lathe, consider the DN Solutions LYNX 2100LMSA horizontal turning center we have for sale. Please contact us for further details. • Condition: New, 0 operating hours • CNC control: FANUC 0i PLUS with 15" touchscreen Capacity: • Chuck size: 6 inches • Max. turning diameter: 300 mm • Max. turning length: 510 mm Axes / Travels • X-axis rapid traverse: 30 m/min • Z-axis rapid traverse: 36 m/min • Number of linear axes: 2 (X / Z) • C-axis: Spindle positioning for milling and drilling operations Main Spindle • Max. spindle torque: 127 Nm Sub-Spindle: • Sub-spindle: Yes • Max. sub-spindle speed: 6,000 rpm Turret: • Turret stations: 12 / 24 • Rotating tool speed: 6,000 rpm Integrated options • Automatic tool changer • High-pressure coolant system: 7 bar Dsdpfxsy Ex A Ue Aplokl Additional equipment • Chip conveyor • Robot interface • Automatic door • Parts catcher with conveyor belt Technical Specification Counter Spindle Yes Driven Tools Yes

Stanje: dober (rabljeno), obratovalne ure: 34.700 h, Funkcionalnost: popolnoma funkcionalen, vrsta goriva: dizel, izhodna frekvenca: 50 Hz, nazivna (navidezna) moč: 1.250 kVA, vrsta hlajenja: voda, MTU dizelski agregat za elektriko vključno z obdelavo izpušnih plinov po 44. BImSchV (od 1/2026, 100 mg NOX, 6 mg prahu ipd.) Pri 21.000 obratovalnih urah je bil opravljen generalni servis v vrednosti več kot 100.000 evrov. Vsi filtri sistema za obdelavo izpušnih plinov so bili zamenjani leta 2025. Dsdey Nbt Ropfx Apljkl Sistem za obdelavo izpušnih plinov je na voljo tudi posebej.

Stanje: kot nova (razstavni stroj), Leto izdelave: 2022, CNC stružnica Doosan Puma GT2100M, letnik 2022/10. Stanje: nova naprava, razstavni model. Z napravo je priložen izmetalec odrezkov Cromar. Djdpjy Azraefx Apljkl

Stanje: zelo dobro (rabljeno), Leto izdelave: 2022, obratovalne ure: 7.800 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Puma 2600, premer struženja nad prečnim suportom: 630 mm, stružna dolžina: 1.245 mm, premer struženja: 376 mm, izvrtina vretena: 102 mm, največja hitrost vretena: 2.800 obr/min, moč vretenovega motorja: 26 W, vrsta vhodnega toka: trifazni, proizvajalec krmilnikov: FANUC, število vreten: 2, delovne ure vretena: 7.800 h, število mest v zalogovniku orodij: 12, Oprema: transportni trak za ostružke, For sale: CNC turning center with sub-spindle and Y-axis. Machine is in excellent condition. Purchased brand-new mid-2023 and still in operation. Less than 8,000 working hours to date, producing parts well below its technical capacity. Serviced exclusively by an authorized distributor. Adapted for robot integration: autodoor and communication signals provided. Equipped with parts conveyor and oil mist filter. NOTE: The robot is not included in the offer—possible sale and implementation support available at separate quotation. TECHNICAL DATA (as per manufacturer's specification): 1) Capacity Swing over bed: 680 mm Swing over carriage: 630 mm Max turning diameter: 376 mm Recommended turning diameter: 315 mm Max turning length: 1245 mm Admissible workpiece weight (incl. chuck): In chuck 500 kg (1,000 kg with support) Bar capacity: Ø102 mm 2) Main Spindle Chuck size: 315 mm Spindle type: A2#11 ASA Front spindle bearing diameter: 160 mm Spindle bore: 115 mm Chuck passage: 103 mm Spindle motor power (cont./30 min): 26/22/18.5 kW (S3 25%/S6 60%/S1 Cont.) Spindle speed range: 2,800 rpm Max spindle torque: 1,123 Nm (15 min S3 15%) Power transmission: Belt 3) Sub-Spindle Chuck: 175 mm (option: 210 mm) Spindle type: A2#5 ASA Spindle bore: 62 mm Sub-spindle cylinder clearance: 50 mm (H8) Sub-spindle drive power (cont./30 min): 7.5/5.5 kW (30 min/S1 Cont.) Djdpfx Asx Rqkuoplekl Spindle speed: 4,500 rpm Max torque: 85 Nm (30 min) Power transmission: Belt 4) Axis Travels X-axis: 260 mm Z-axis: 1,350 mm Y-axis: 105 mm (±52.5 mm) B-axis: 1,350 mm C-axis: 360° (0.001° increments) Rapid traverse (X): 30 m/min Rapid traverse (Z): 30 m/min Rapid traverse (Y): 10 m/min Rapid traverse (B): 30 m/min C-axis speed: 200 rpm 5) Bed and Saddle Slant bed, incline angle: 30° Bed guideway width (Z): 437 mm Saddle guideway width (X/Y): 321/325 mm Sub-spindle clearance: 335 mm 6) Tool System Tool holder: BMT 65P Tool stations: 12 Tool size: 25 x 25 mm Max drill diameter: 50/32 mm (main/sub-spindle) Driven tool power: 7.5/1.5 kW (5 min/Cont.) Driven tool speed: 5,000 rpm Driven tool torque: 95.5 Nm Driven tool collets (ER32): Ø3–Ø20 mm (option) Turret indexing: 1 position/0.15 s, 1.2 s full station Max driven tool drilling diameter: Ø20 mm, M20 x P2.5 7) Hydraulic System Tank capacity: 20 l Flow rate (60/50 Hz): 25 / 20.8 l/min Power/Pressure: 2.2 kW x 5.0 MPa 8) Coolant Tank capacity: 250 l Flow rate: 30 l/min Power/Pressure: 0.7 kW x 0.15/0.1 MPa (60/50 Hz) 9) Machine Accuracy Positioning (X, Z, Y, C): 0.01 mm Repeatability: X/Z/Y axes: ±0.002/±0.003/±0.003 mm C axis: ±0.006° 10) Other Electrical control X/Z/Y axes: 0.02 mm C axis: 0.0167° For any questions or further information, please send us a message or contact us by phone.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Djdpovf E Avofx Aplskl Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2000, obratovalne ure: 32.169 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 60 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.320 mm, širina bale: 1.100 mm, višina bale: 720 mm, teža bale: 750 kg, skupna masa: 22.000 kg, kapaciteta rezervoarja za olje: 900 l, For sale is a complete baling press system consisting of conveying technology, baler (partially overhauled and tested), and wire stations. Technical data (baler): Manufacturer: Bollegraaf Recycling Machinery B.V. Model: HBC 60A Year of manufacture: 2000 Operating hours: 32,169 hours (as of November 2024) Main press force: 60 t Pre-press force max.: 25 t Feed chute dimensions: 1,320 x 1,100 mm Theoretical cycle time: 18 seconds Bale size: 1,100 x 720 mm, variable length Drive power: 45 kW Total connected load: 60 kW Tying: 5-fold vertical Throughput rates at a bulk density of 30 kg/m³: approx. 5.5 t/h 50 kg/m³: approx. 10 t/h 100 kg/m³: approx. 16 t/h Bale weights: 400 up to 750 kg, depending on material PLC: Telemecanique TSX Micro Baler weight: approx. 22 t Scope of supply: 1 chain belt conveyor 1 Bollegraaf HBC 60A baler with fluffing unit (wirbulator) 1 maintenance platform with access ladder 2 wire stations with guide pulleys for 10 wire reel stands (without wire) The following repair and overhaul work has been carried out: - Hydraulic oil tank drained, cleaned, and refilled with new oil - Oil filter and air filter replaced - Hydraulic block partially resealed - Hydraulic hose at the hydraulic block replaced - Wire run-in marks at the base passages welded and smoothed Dsdpfxjviwdmo Aplskl - Tying unit cleaned and serviced - Electrical system repaired, door interlock switches partially replaced - Fluffing unit repaired - General maintenance carried out, machine lubricated - Machine tested under power, without material, in manual and automatic mode—see function video Remarks: The system has already been completely dismantled, stored, and is ready for prompt loading. Documentation (operating manual, CE, electrical/hydraulic circuit diagrams) is available. Viewing by appointment is possible. We accept no liability for the technical specifications or any errors.

Leto izdelave: 2022, stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: SPE-Spero QTX-340, Naprava je bila uporabljena za raziskovalne namene, SPE-Spero QTX-340, MIR-mikroskop s funkcijo „Hyper Spectral Imaging“. Spektralna pokritost področja prstnih odtisov (1900 - 950 1/cm). High-Res-IR objektiv: 12,5X; NA:0,7, 650μm FOV. Enhanced LowMag-Lens Za vidno svetlobo: 4,0X; NA:0,13, 650μm FOV. 480*480 slikovnih pik, širokopasovna mikrobolometerska kamera. Kamera za vidno svetlobo. QT-Laser-Performance-Paket vključno z visoko natančnim avtomatiziranim odrom (< 1μm ponovljivost natančnosti). Hitro zajemanje podatkov. Joy Stick, kontrolni računalnik, Win10. »Diskretna frekvenčna IR-slikovna« v realnem času. Delovanje v transmisiji in refleksiji. 4000 ur aktivnega laserja. Dodoy Dcd Hspfx Aplokl

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, moč: 1.013 kW (1.377,30 KM), V ponudbi, nova Znamka: MTU Dsdpey Hiwlofx Apljkl Tip: 8V 4000 GS L64 FNER Leto izdelave: 2025 Moč: 1013 kW Napetost: 400 V 50 Hz Obratovalne ure: 0 Z garancijo proizvajalca Obseg dobave: Generator set Plinska rampa MMC kontrolna plošča

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, stružna dolžina: 300 mm, premer struženja: 300 mm, izvrtina vretena: 52 mm, največja hitrost vretena: 4.500 obr/min, model krmilnika: FANUC CNC, TEHNIČNI PODATKI Maks. premer struženja: 300 mm Maks. dolžina struženja: 300 mm Vretenova odprtina: 52 mm Glavna vretena hitrost: 4.500 min⁻¹ Orodjarski revolver: 12 postaj PODATKI O STROJU Teža stroja: 2.200 kg OPREMA Horizontalni CNC stružnica Visoko zmogljivo glavno vreteno Robustna konstrukcija stroja za visoko dimenzijsko natančnost Orodjarski revolver s hitro indeksacijo Kompaktna zasnova, mala potreba po prostoru Uporabniku prijazna CNC krmiljenje Visoka zanesljivost in nizko vzdrževanje Krmiljenje: FANUC CNC Dkedpfsyvfvusx Apljl

Stanje: dober (rabljeno), CHP plant (natural gas), 2 units Onsite Energy ME3042L3, year 2009. Engine: MTU E3042L9, year 2016, 23,000 operating hours. Dksdoun I N Hepfx Aplol Generator: LSA C47.2M7 C6/4, 400V, 50Hz, 465kVA. Absorption chiller: Carrier 16LJ-A24E, 689kW cooling capacity. Emergency cooler: Güntner GFH 090.2B/2x2-M. 12m chimney, silencer, pumps, actuators, dampers, valves, gas control section. Main control system: synchronisation, load management, island mode, grid support, etc., load distribution cabinets. Electrical output: 714kWe, thermal output: 1,058kW, cooling output: 689kW.

Stanje: dober (rabljeno), Funkcionalnost: popolnoma funkcionalen, Vertical form, fill, and seal packaging machine Brand: Jasa Packaging Solutions B.V. Model: PMT Horizontal seal length: 270 mm Dksdjv Utd Hopfx Aplsl Film width: 620 mm Overall dimensions: 2800 mm x 1450 mm x 2350 mm.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, moč vretenovega motorja: 7.500 W, največja hitrost vretena: 4.000 obr/min, potovalna razdalja osi X: 175 mm, pomik po osi Z: 330 mm, skupna višina: 1.635 mm, skupna širina: 1.690 mm, skupna masa: 2.600 kg, proizvajalec krmilnikov: FANUC, največja dolžina izdelka: 1.850 mm, število osi: 3, This 3-axis turning and milling center DN SOLUTIONS Leo 1600 was manufactured in 2023. It features a maximum turning diameter of 320 mm and a turning length of 303 mm. The machine is equipped with a 6-inch main spindle chuck and offers rapid traverse speeds of 30 m/min in both the X and Z axes. If you are looking for a high-quality lathe, you should consider the DN SOLUTIONS Leo 1600 machine we are offering for sale. Contact us for further details. • Main spindle chuck size: 6 inches (153 mm) • Bar capacity: 45 mm • Rapid traverse X: 30 m/min • Rapid traverse Z: 30 m/min • Main spindle torque: 72 Nm • Maximum turning diameter: 320 mm • Maximum turning length: 303 mm • Number of tool stations: 12 • Guideway type: Linear guide rails • Screen size: 10.4 inches • Electrical connection: 380 V • Electrical supply: 3 phases • Frequency: 50 / 60 Hz • Rated power: 14.97 kVA • Full load current: 22.74 A • Short-circuit rating: 10 kA • Breaking capacity: 5 kA Additional equipment • Optional: • 8 pcs external clamping jaws Dsdeyu R Nwopfx Aplskl • 1 pc facing tool block 850418 (500-5804) • 3 pcs internal turning tool holders • Chip conveyor (hinged belt conveyor), price on request • The machine is supplied with a standard base package: turret fully equipped, including basic tool block Technical Specification Counter Spindle No Driven Tools Yes

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, moč vretenovega motorja: 22.000 W, največja hitrost vretena: 3.000 obr/min, potovalna razdalja osi X: 293 mm, pomik osi Y: 130 mm, pomik po osi Z: 1.350 mm, skupna višina: 2.315 mm, skupna širina: 2.067 mm, skupna masa: 8.000 kg, proizvajalec krmilnikov: FANUC, model krmilnika: 0i-F, največja dolžina izdelka: 4.530 mm, število osi: 4, This 4-axis turning and milling center DN SOLUTIONS 3100 LY was manufactured in 2023. It offers a maximum turning diameter of 420 mm and a turning length of 1285 mm. The machine is equipped with a 12-inch main spindle chuck and rapid traverse speeds of 30 m/min on the X and Y axes. If you are looking for a high-quality turning center, consider the DN SOLUTIONS 3100 LY machine we have for sale. Contact us for more details. • Main spindle chuck size: 12 inches (306 mm) • Bar capacity: 102 mm • Rapid traverse: X 30 m/min; Y 30 m/min; Z 10 m/min • Maximum turning diameter: 420 mm • Maximum turning length: 1285 mm • Driven tool speed: 5000 rpm • Tool turret: 12 stations, BMT65 • Guideway type: Box guideways • Axes/Features: C-axis, Y-axis • Electrical: 380 V, 3-phase, 50/60 Hz • Electrical power: 55.02 kVA; full load current 83.60 A; short-circuit power 10 kA; breaking capacity 5 kA Additional Equipment • Optional: • 1 external turning holder BMT65 25x25, single, left/right (500-0679) • 3 external turning toolholders R/L, high (500-6960) • 1 facing turret BMT65P/SQ 25 mm (500-0834) • 3 boring bar holders (ID: 50 mm) BMT65P (500-5555) • 1 coolant cover (500-0837) • 1 reducing bushing set • 1 reducing bushing set (500-0808) • 1 adapter set PRECI-FLEX Er32 (BMT 65P) (500-0500) • 12 covers BMT 65 (500-1931) • 2 angled externally cooled Eppinger AGWs • 2 straight externally cooled Eppinger AGWs • Chip conveyor (hinge belt conveyor). Price on request • The machine comes with a standard basic package: turret head fully equipped, including base holders Dkedpfxeyu Rn Tj Aplel The machine is a showroom model, never used in production. Like new. Technical Specification Counter Spindle: No Driven Tools: Yes

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, moč vretenovega motorja: 45.000 W, največja hitrost vretena: 1.500 obr/min, potovalna razdalja osi X: 362 mm, pomik osi Y: 110 mm, pomik po osi Z: 1.105 mm, skupna višina: 2.194 mm, skupna širina: 2.056 mm, Premer palice (maks.): 166 mm, skupna masa: 10.750 kg, proizvajalec krmilnikov: FANUC, model krmilnika: 0i-F Plus iHMI Touch, največja dolžina izdelka: 4.759 mm, število osi: 4, This 4-axis DN SOLUTIONS PUMA 5100 MB was manufactured in 2023. It features a maximum turning diameter of 650 mm and a turning length of 952 mm. The machine is equipped with a 21-inch main spindle chuck and offers rapid traverse speeds of up to 20 m/min. If you are looking for high-quality turning capabilities, consider the DN SOLUTIONS PUMA 5100 MB turn-mill center that we have for sale. Contact us for further details. • Main spindle chuck size: 21 inch (535 mm) Dkodpfx Ajyuywkjplsl • Bar capacity: 166 mm • Rapid traverse X: 16 m/min • Rapid traverse Z: 20 m/min • Max. rapid traverse: 20 m/min • Main spindle torque: 2957 Nm • Maximum turning diameter: 650 mm • Maximum turning length: 952 mm • Driven tools speed: 4000 rpm • Number of tool stations: 12 • Tool interface: BMT75 • Guideway type: box ways • Spindle bore: 117–166 mm (depending on configuration) • Coolant system: high-pressure coolant through the turret • Tailstock: programmable tailstock • Tool measurement: automatic hydraulic tool measurement • Cutting force monitoring: yes • Thread cutting: fixed point threading with variable speed • Additional handwheel: yes • Automatic machine door: yes • Electrical connection: 380 V • Electrical connection: 3 phase • Frequency: 50 / 60 Hz • Rated power: 61.56 kVA • Full load current: 93.53 A • Short-circuit resistance: 10 kA • Breaking capacity: 5 kA Additional equipment • Optional: • 4 pcs. external clamping jaws (500-0838) • 1 pc. raised external toolholder • 1 pc. facing toolholder R/L • 6 pcs. internal turning toolholder • 1 pc. internal end cap (500-0839) • 1 pc. reduction sleeve set for boring • 1 pc. U-drill reduction sleeve set • 2 angled, externally cooled Eppinger external toolholders • 2 straight, externally cooled Eppinger external toolholders • Optional: chip conveyor (hinged belt conveyor). Price upon request. • The machine comes with a standard base package: turret fully equipped, including basic holders Technical Specification Counter Spindle: Yes Driven Tools: Yes

Stanje: zelo dobro (rabljeno), Leto izdelave: 2020, Funkcionalnost: popolnoma funkcionalen, skupna širina: 120 mm, skupna dolžina: 220 mm, skupna višina: 245 mm, uporabna prostornina rezervoarja: 3.300 l, Treasure v skladu z Valrem. Ognjevarna zaščita > 120 min Zunanje dimenzije: Djdpfeykapfjx Aplskl Dolžina: 220 cm Širina: 120 cm Višina: 245 cm Notranje dimenzije: Dolžina: 170 cm Širina: 95 cm Višina: 210 cm

Stanje: rabljeno, Leto izdelave: 2006, obratovalne ure: 71.000 h, Funkcionalnost: popolnoma funkcionalen, Plinski generator mtu 16v 4000 gs l61. Leto izdelave: 2006 Delovne ure: 71.000 Dodey At Awepfx Aplekl Napetost: 10.000 V Dobava vključuje: * agregat na okvirju * krmilna plošča za plinsko inštalacijo * črpalna enota * dokumentacija in dnevnik obratovanja V celoti delujoče stanje

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2026, RSS 600 serija Mono Rotor Shredder (nova serija) 18,5 kW Velikost sita po dogovoru Primeren za različne vrste plastike/lesa/ali drugih materialov Možne prilagoditve glede motorjev, sita, okvirja. Možna dovodna in odvodna transportna trakova, skladiščenje, ločevanje kovin. Na voljo tudi večji ali manjši modeli. Odvodni trak ali polž po želji. Za vprašanja nas pokličite ali nam pišite, z veseljem vam svetujemo. POMEMBNO! Prosim navedite vaše ime, ime podjetja in telefonsko številko. Dkedpfx Apoirt H Aolol