Lider Lowbed 4A nakup rabljenega (1.246)

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 14.680 kg, največja dovoljena obremenitev: 35.320 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 600 mm, skupna dolžina: 15.400 mm, skupna širina: 2.550 mm, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, Tailor-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is just an example. Production and equipment are customized to meet each customer’s needs. Chassis Lowbed semi-trailer Steel welded construction, fifth wheel plate with replaceable 2" king pin 24 t, two-speed landing gear, single-sided operation, with straight base, without shift compensation Rear supports, foldable 2x wheel chocks with holders Aluminum side underrun protection Quarter-shell mudguards in front of and behind axle assembly With splash guards behind each axle 1x storage box, w=2,350 mm x l=730 mm x h=640 mm, mounted transversely at the front of the gooseneck, with 2 storage trays Extendable widenings up to 3,000 mm (not on rear slope) (the track width of the construction machinery or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for wooden beams on the gooseneck, transverse at the front 70 mm wooden beams for extending to 3,000 mm Digger boom recess over the rear axles, extending to the rear, approx. 500 mm wide and approx. 230 mm deep Lashing eyes low loader 3 pairs of lashing eyes rated at 10 t each in front on the gooseneck, 8 pairs at 10 t each in the lowbed, 3 pairs of lashing rails in the track area of the lowbed, 3 pairs of lashing eyes at 10 t each in the axle/rear area Axles and suspension SAF drum brake axles Axles/chassis laser-aligned: reduces tire wear and fuel consumption With steering axle Air suspension Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel twin wheels, factory silver Braking system Two-line compressed air braking system, colored pipes for easier service Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer must only be towed by tractors that ensure ABS functionality! 2 foolproof coupling heads at the front, without connecting line With lift & lower valve, hold function in lower position + auto-reset function Axle load detection via EBS CAN bus signal, for display in the truck cab (truck must be properly prepared, no truck installation, not a certified scale) Vehicle stability system Trailer Info Center, for displaying vehicle data such as axle loads (not a certified scale), mileage, and diagnostics/system messages. Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white LED position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin foolproof sockets at the front 1x additional LED work light at the rear 1x LED beacon with holder, controlled via parking lights 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Guodji Ri Hgopfx Aa Uoc Flooring Gooseneck with steel/chequer plate cover 70 mm softwood flooring in the track area, steel/chequer plate in wheel arch area, lowbed left and right in track area hydraulically liftable via truck PTO Rear slope with 70 mm softwood flooring Lowbed length approx. 6,300 mm Side boards 25 mm aluminum hollow section, 400 mm high, insertable at the front and sides of the gooseneck Loading ramps Steel ramps, 2,800 mm long, 750 mm wide Tailor-made transport solution Configure your Fliegl vehicle to your requirements. The vehicle shown is for illustrative purposes. Production and equipment will be tailored individually according to customer specifications.

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 11.800 kg, največja dovoljena obremenitev: 29.200 kg, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.350 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 13.650 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, Tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customised individually as per the customer’s wishes. Chassis Low-loader semi-trailer Steel welded construction, fifth wheel plate with replaceable 2" kingpin and two kingpin positions 24 t two-speed landing gear, single-sided operation, with semi-circular base and straight mounting plate, with load equalizer Foldable rear support Wheel chocks with holder Side underrun protection, aluminium Mud flaps in front of 1st axle and behind each axle with anti-spray, compliant with EC regulations Toolbox stainless steel, width=600 mm / height=400 mm / depth=500 mm, with polished, lockable door Hydraulic lift table after gooseneck, approx. 3000 mm long, hydraulically liftable for crossing the gooseneck, with mechanical locking in raised position. Operated via radio remote control Electric cable winch, 24 Volt, pulling force 8165 kg, mounted centrally at the very front on the loading area at the gooseneck, housed in a stainless steel box with door (technically achievable subject to detailed verification), operated by radio remote control, cable length 35 m x approx. 10 mm, with roller cable guide and detachable guide rollers on gooseneck and rear incline. Lashing eyes low-loader Gooseneck: 5 pairs of lashing eyes embedded in the outer frame, each rated for 5 t. 2 pairs of central lashing eyes, each for 5 t. 1 pair of lashing mushrooms embedded in the upper outer frame at the neck inclination, each for 10 t. Bed: 4 pairs of lashing eyes embedded in the outer frame, each for 5 t. 4 pairs of central lashing eyes, each for 5 t. 1 pair of lashing mushrooms embedded in the upper outer frame, each for 10 t. Well: 4 pairs of lashing eyes embedded in the outer frame, each for 5 t. 5 pairs of central lashing eyes, each for 5 t. 4 pairs of lashing mushrooms embedded in the upper outer frame, each for 10 t. Axles and Suspension SAF drum brake axles Axles/chassis laser alignment to reduce tyre wear and fuel consumption Last axle is steered, with automatic reverse lockout via reverse light, and additional locking function via manual button on vehicle Air suspension with raise & lower valve, holding function for lowering, auto-reset function Wheels and Tyres 235 / 75 R 17.5 according to manufacturer’s choice Guedpfxei Ri E Uo Aa Uoc Twin-mount steel rims, factory silver Braking System 2-line compressed air brake system Spring-loaded parking brake Vehicle stability control system Axle load detection via EBS-CAN bus signal, for display in the cab (truck must have appropriate pre-installation, no truck installation included, not a calibrated scale) 2 anti-swap coupling heads at front, without connecting line EBS, electronic braking system with EBS socket at front, without connection cable Electrics 24 Volt, multi-chamber lights, yellow LED side marker lighting 2 white position lights at front 2 white/red lane guidance lights at rear All lighting fully in LED design 2 x 7-pin and 1 x 15-pin anti-swap sockets at front Additional LED work light at rear, switched via reverse light LED rotating beacon with bracket, switched via position light Pair of double warning boards with LED illumination, extendable to 3,000 mm Flooring Gooseneck covered with Mega Grip serrated grating / low-loader deck covered with Mega Grip serrated grating / rear incline covered with Mega Grip serrated grating Front wall / front corner posts Steel, 1200 mm high, with c

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 8.900 kg, največja dovoljena obremenitev: 26.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 13.300 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, Customised Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored individually to customer specifications. Chassis Low-bed Semi-Trailer Steel welded construction, fifth wheel plate with interchangeable 2-inch kingpin and two kingpin positions, 24 t two-speed landing gear, single-sided operation, with straight lower section, without load compensation Rear support foldable 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflap Mudguards in front of the 1st axle and behind each axle with antispray, compliant with EC regulations Extendable widenings to 3,000 mm (not in rear slope) Storage compartment for timber planks in the centre of the loading area 70 mm timber planks for extension to 3,000 mm Lashing Points Low-bed 2 pairs of ring lashing eyes each rated for 5 t at the front on the gooseneck 11 pairs of lashing mushrooms embedded on the top and side of the outer frame, each rated for 10 t 2 x on gooseneck 9 x distributed on the low-bed deck First lashing point 250 mm from the front and last one max. 250 mm from the rear, distance between lashing points not greater than 1,100 mm Gsdpji Ri E Rsfx Aa Ujuc 8 pairs of stake pockets embedded in the outer frame, inner dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes) Axles + Suspension SAF drum brake axles Air suspension Wheels and Tyres 235 / 75 R 17.5 Steel rims, twin arrangement, factory silver Braking System 2-line compressed-air braking system Coloured hose arrangement for easy servicing Spring-loaded parking brake EBS, Electronic Braking System with EBS socket at the front, without connection cable 2 anti-mistake couplings at the front, without connection line With lift & lower valve Axle load detection via EBS-Canbus signal, for display in the driver’s cab Vehicle stability control system Electrics 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin anti-mistake sockets at the front, without connecting cable 1 LED beacon with holder 2 pairs of double warning boards, LED lit and extendable to 3,000 mm Floor Gooseneck with steel plate covering Storage box fitted into the ramp to gooseneck Then 70 mm softwood flooring, in wheel arch area with steel/chequer plate covering Rear slope with 70 mm softwood flooring Low-bed area including rear slope: 9,200 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber planked Hydraulic operation via tractor auxiliary drive with throttle, operation on left side in driving direction Hydraulic connection with SVK coupling NW 10/3, without connection hoses Customised Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored individually to customer specifications.

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 8.900 kg, največja dovoljena obremenitev: 32.100 kg, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 13.300 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, Tailored Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Lowbed Semi-Trailer Chassis Steel welded construction, fifth wheel plate with replaceable double kingpin and two kingpin positions 24 t two-speed landing gear, single-sided operation, with straight lower part, without compensating device Rear supports foldable 2 wheel chocks with holders Gujdpfx Aoi Ri Hcea Uec Side underrun protection in aluminium Quarter-shell mudguards in front of and behind the axle assembly 1st pair of wheel recesses recessed after the gooseneck in the lowbed platform area, with ramped entry. Length at the bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note: Main beam area 260 mm higher than the wheel recess. 2nd pair of wheel recesses between axle A and B. Length at the bottom approx. 350 mm, depth approx. 260 mm. Note: Main beam area 260 mm higher than the wheel recess. If wheel loaders are to be transported and the overall height needs to be checked, please provide the technical data sheet for the wheel loader types with precise specifications (if the total height is exceeded). Wheel recess covers sliding out from the main frame, with timber inserts. Extendable widening to 3,000 mm (not in rear ramp slope and not in the bottom of the wheel recesses) Storage compartment for timber planks on the gooseneck, positioned transversely at the front Timber planks 70 mm for widening to 3,000 mm Tie-down points lowloader 2 pairs of ring lashing eyes, each 5 t at the front on the gooseneck 11 pairs of lashing mushrooms recessed into the upper and side outer frame, each 10 t 2 x on the gooseneck, 9 x distributed in the low loader bed, first lashing eye 250 mm from the front and the last max. 250 mm from the rear, distance between lashing eyes not exceeding 1100 mm 8 pairs of stake pockets recessed in the outer frame, inside 70 x 40 mm, or instead of stake pockets, 5 t ring lashing eyes recessed in the floor Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tyre wear and fuel consumption Air suspension Wheels and tyres 235 / 75 R 17.5 to manufacturer’s choice Steel rims in twin configuration, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connection cable 2 fail-safe coupling heads at the front with raise & lower valve Axle load detection via EBS Canbus signal, for display in the driver’s cab, truck must be correspondingly equipped Vehicle Stability Control System Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin fail-safe sockets at the front 1 x LED beacon with holder, switchable via parking light 2 pairs of warning boards, double, LED illuminated and extendable to 3,000 mm, removable with plug Flooring Gooseneck with steel/chequer plate overlay Storage box embedded in the transition slope to the gooseneck After that, with 70 mm softwood flooring; in the bottom of the wheel recesses and wheel arch area steel/chequer plate overlay Lowloader platform including rear ramp slope 9,100 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp securing device below Tailored Transport Solution Configure your Fliegl vehicle according to your individual requireme

Stanje: kot nova (razstavni stroj), Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: VT0479, VC850 Travel ranges: X 850 mm, Y 510 mm, Z 510 mm High-performance milling spindle up to 12,000 rpm as an integrated hybrid spindle with direct drive (no belt) Spindle tool interface: SK40 DIN69871 with pull stud DIN69872-A / ISO 7388-3-AD TOOL MAGAZINE with 32 tool stations DIRECT MEASURING SYSTEMS on X/Y/Z axes SIEMENS 840DE control system with the following standard features: - SPINNER - SPIOS 24" touch control panel for Industry 4.0 applications - Height-adjustable, rotatable, and tiltable operating panel for optimal ergonomics - Includes engraving cycles - 24" liquid crystal color flat panel display with multi-touch functionality - User memory 2 GByte - 15 zero point offsets - 1 free USB port Godpoy S Tpisfx Aa Uouc - Standard Ethernet port Latest SIEMENS control generation "SINUMERIK ONE": - SPINNER - SPIOS 24" touch control panel for Industry 4.0 applications - Height-adjustable, rotatable, and tiltable operating panel for optimal ergonomics - Includes engraving cycles - 24" liquid crystal color flat panel display with multi-touch functionality - User memory 2 GByte - 15 zero point offsets - 1 free USB port - Standard Ethernet port SPINNER MULTI-CONTROL WHEEL integrated in the control panel, offering the following functions in a single control element: - Handwheel function in jog mode - Feed override in automatic mode - Start button and feed adjustment in single-block setup mode, self-resetting to 0% at end of block -> All essential setup functions combined in one control element Features: - SHOPMILL - 3D SIMULATION - REMNANT MATERIAL DETECTION - DXF READER Fully integrated 1-axis TILTING TABLE (SP), centrally mounted on work table with: - Swivel carriage approx. 580 mm long for 3-sided machining - Endless swivel range of the A-tilt axis - Counter bearing for support of the rotary table bridge UNIVERSAL CHIP CONVEYOR for VC850 Spindle PREPARATION FOR HIGH PRESSURE for use of auxiliary tank up to 22 bar HIGH PRESSURE TANK 22 bar Additional air blast at the spindle head Central compressed air feed through milling spindle as an alternative to flushing pistol inside the working area SPINNER STANDARD PROBE PREPARATION Wireless SPINDLE PROBE Universal robot interface (UNIROB) WORKPIECE CLAMPING HYDRAULICS, incl. 2 pcs. 4/4-way valves for hydraulic clamping up to 200 bar STANDARD DOCUMENTATION IN GERMAN consisting of machine manual and CNC manuals, provided in digital form on the control system. Printed manuals available for an additional charge. LIFTING EYE BOLTS for crane unloading, set of 4 pcs. (required for crane transport) STANDARD PAINT, two-tone in light grey RAL7035 and blue-grey RAL5008 Electrical configuration according to EUROPEAN STANDARD: Mains voltage 3x400V +/-10% Mains frequency 50Hz (+/-2%) TN network (5-wire system) Notes: The price includes warranty services only within Germany. For new and demo machines, the images are not necessarily of the specific machine but of comparable units. Accessories shown, such as workholding or tool holders, are only included as stated in the technical specifications. Please request a detailed ex-works quotation. Visit our production facility near Munich or one of our showrooms. We may have additional offers for comparable machines. Subject to prior sale.

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, lastna masa: 11.800 kg, največja dovoljena obremenitev: 27.200 kg, skupna masa: 39.000 kg, konfiguracija osi: 2 osi, prva registracija: 10/2018, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 300 mm, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245.70 R 17.5, odmik od tal: 300 mm, barva: svetlo zelena, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2018, Oprema: ABS, Rabljeni polpriklopnik culla vasca De Angelis, 3 osi, 2 krmiljeni osi Tridec s krmiljenjem iz zgloba in hidravličnim upravljanjem preko žične komande in centralne enote, snemljiv in nastavljiv vrat, podaljšljiva tovorna površina za dodatnih 5,40 m k osnovnim 7,0 m ob zaprti culli, pnevmatsko vzmetenje, odstranljive aluminijaste klančine za vzpon, stranski rud kavlji, stranski razširitveni elementi, leto 2018, tehnično pregledan do 31.10.2026 – PRODAJALEC INTERDRIVESRL-PARMA Guedsy T Sbtjpfx Aa Uec

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 11.500 kg, največja dovoljena obremenitev: 27.500 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2014, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 3.150 mm, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 205.65 r 17.5, odmik od tal: 750 mm, barva: svetlo zelena, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2014, Oprema: ABS, Rabljen polpriklopnik nizkopodna prikolica Meusburger Buche s ponjavo, 4 osi, 3. in 4. krmiljeni, 1. os dvižna, vdolbine v podu z odstranljivimi pokrovi, razširljiva in po višini nastavljiva ponjava, drsna streha, zadnja vrata, priprava za odstranljive zadnje klančine, RUD kavlji ob strani in v podu, ležišča za stebre rulasi s prečkami preko podna, ponjave prilagojene za stranski izredni tovor z izvlečnimi tablami, notranja višina 3,10 m + dodatek 40 cm v vdolbinah, letnik 2014, zadnje stabilizacijske noge. PRODAJALEC INTERDRIVE SRL-PARMA. Gujdpfx Aaey T Ruro Ujc

Stanje: rabljeno, Volt / V Gusdpfx Aasy S Dpms Uoc Amper / A Teža / kg Skupna potrebna moč / kW

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2019, obratovalne ure: 21.000 h, vpenjalna sila: 1.270 kN, skupna širina: 1.500 mm, skupna višina: 1.700 mm, skupna masa: 5.300 kg, največja dolžina izdelka: 5.100 mm, This 3-axis SHIBAURA EC130SXIII-4A was manufactured in 2019. It features a clamping force of 1270 kN and a mold opening stroke of 400 mm. The machine offers a maximum distance between tie bars of 950 mm and a platen size of 720 x 670 mm. If you are looking for a high-quality injection molding machine, consider the all-electric SHIBAURA EC130SXIII-4A that we have for sale. Please contact us for further details. • Tie bar spacing (H x V): 510 x 460 mm • Platen dimensions (H x V): 720 x 670 mm • Mold opening stroke: 400 mm • Max. distance between platens: 950 mm • Mold height (min-max): 180-550 mm • Ejector force: 30 kN (3.0 tf) • Ejector stroke: 90 mm Guodpfxey Iffnj Aa Usc • Injection unit code: 14 • Nozzle contact force: 17.7 kN (1.8 tf) • Injection speed (standard): 300 mm/s • Injection speed (high torque): 200 mm/s • Injection speed (high speed): 400 mm/s • Main switch capacity (standard/high torque): 100 A • Main switch capacity (high speed): 125 A • Transformer (standard): 75 kVA

Stanje: zelo dobro (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 05/2022, dolžina tovornega prostora: 19.190 mm, širina tovornega prostora: 2.550 mm, skupna dolžina: 179.900 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245/70-R17.5, barva: drugo, Leto izdelave: 2022, Oprema: ABS, = Additional Options and Accessories = - BPW axles - EBS (Electronic Braking System) - Lift axle - Air suspension - Drum brakes - Central lubrication system = Remarks = Well-maintained 2022 KASSBOHRER LOWBED LB3E extendable low-loader with ABS/EBS, extendable once (600 cm), hydraulic ramps (265x85 + 140x85 cm), BPW Eco-Plus axles with drum brakes, 1st axle = lift axle, 3rd axle = steering axle (trailing axle), hardwood floor (floor height: 89 cm) with extensions (left + right: trailer width extendable up to 3,150 mm), heavy-duty lashing rings in the side beams (left + right), heavy-duty lashing rings in the floor (left + right), rear support legs, 4x width markers, tyres 245/70-R17.5 (tread left: 6/7, 6/12, 9/4 mm; tread right: 8/4, 5/8, 6/7 mm), unladen weight: 13,060 kg, permissible total weight: 48,000 kg, Belgian registration with valid technical inspection until 24.05.2026 = Further Information = Axle configuration Tyre size: 245/70-R17.5 Axle brand: BPW Eco-Plus Brakes: Drum brakes Suspension: Air suspension Rear axle 1: twin tyres; lift axle; max. axle load: 10,000 kg; tyre tread left inside: 45%; left outside: 40%; right inside: 25%; right outside: 50% Rear axle 2: twin tyres; max. axle load: 10,000 kg; tyre tread left inside: 75%; left outside: 40%; right inside: 50%; right outside: 35% Rear axle 3: twin tyres; max. axle load: 10,000 kg; steered; tyre tread left inside: 25%; left outside: 55%; right inside: 45%; right outside: 40% Weights Unladen weight: 13,060 kg Payload: 34,940 kg Gross vehicle weight: 48,000 kg Functionality Body brand: KASSBOHRER LOWBED LB3E Extendable body: Yes Condition Technical condition: very good Optical condition: very good Gedeyz A Ugspfx Aa Uouc Identification Registration number: QACP318 Further information Please contact Arne Honingh for more information.

Stanje: zelo dobro (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 05/2022, dolžina tovornega prostora: 19.190 mm, širina tovornega prostora: 2.550 mm, skupna dolžina: 179.900 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245/70-R17.5, barva: drugo, Leto izdelave: 2022, Oprema: ABS, = Additional Options and Equipment = - BPW axles - EBS (Electronic Braking System) - Lift axle - Air suspension - Drum brakes - Central lubrication = Notes = Attractive 2022 KASSBOHRER LOWBED LB3E extendable low loader with ABS/EBS, 1x extendable (600 cm), hydraulic ramps (265x85 + 140x85 cm), BPW Eco-Plus axles with drum brakes, 1st axle = lift axle, 3rd axle = steering axle (trailing axle), hardwood floor (floor height: 89 cm) with extensions (left + right: semi-trailer can be widened up to 3150 mm), heavy-duty lashing rings in the side members (left + right), heavy-duty lashing rings in the floor (left + right), rear support legs, 4x width markers, tyres 245/70-R17.5 (tread left: 6/7, 6/12, 9/4 mm; tread right: 8/4, 5/8, 6/7 mm), unladen weight: 13,060 kg, permissible gross weight: 48,000 kg, Belgian registration with valid technical inspection until 24/05/2026 = Further Information = Axle configuration Tyre size: 245/70-R17.5 Gedpjzad Anofx Aa Ueuc Axle manufacturer: BPW Eco-Plus Brakes: Drum brakes Suspension: Air suspension Rear axle 1: twin tyres; lift axle; max. axle load: 10,000 kg; left inner tyre tread: 45%; left outer tyre tread: 40%; right inner tyre tread: 25%; right outer tyre tread: 50% Rear axle 2: twin tyres; max. axle load: 10,000 kg; left inner tyre tread: 75%; left outer tyre tread: 40%; right inner tyre tread: 50%; right outer tyre tread: 35% Rear axle 3: twin tyres; max. axle load: 10,000 kg; steered; left inner tyre tread: 25%; left outer tyre tread: 55%; right inner tyre tread: 45%; right outer tyre tread: 40% Weights Unladen weight: 13,060 kg Payload: 34,940 kg Gross vehicle weight (GVW): 48,000 kg Functional Body manufacturer: KASSBOHRER LOWBED LB3E Extendable body: Yes Condition Technical condition: very good Visual condition: very good Identification Registration number: QACP318

Stanje: rabljeno, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 9.000 kg, dovoljena osna obremenitev (os 2): 9.000 kg, dovoljena osna obremenitev (os 3): 9.000 kg, prva registracija: 02/1996, dolžina tovornega prostora: 13.460 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 3.100 mm, skupna širina: 2.570 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R17.5, stanje pnevmatik: 30 odstotek, medosna razdalja: 9.490 mm, barva: drugo, Leto izdelave: 1996, Oprema: ABS, = Dodatne možnosti in oprema = - BPW osi - Zračno vzmetenje - Bobnaste zavore = Dodatne informacije = Konfiguracija osi Dimenzija pnevmatik: 245/70 R17.5 Godoy Uliyopfx Aa Uouc Znamka osi: SAF Zavore: Bobnaste zavore Zadnja os 1: Največja obremenitev osi: 9.000 kg; Profil pnevmatik: 30% Zadnja os 2: Največja obremenitev osi: 9.000 kg; Profil pnevmatik: 30% Zadnja os 3: Največja obremenitev osi: 9.000 kg; Profil pnevmatik: 40% Teže Lastna teža: 7.040 kg Nosilnost: 31.960 kg Skupna dovoljena masa: 39.000 kg Identifikacija Registrska številka: OD-72-TR

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 8.000 kg, največja dovoljena obremenitev: 39.000 kg, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 13.000 kg, dovoljena osna obremenitev (os 2): 13.000 kg, dovoljena osna obremenitev (os 3): 13.000 kg, prva registracija: 07/1983, dolžina tovornega prostora: 11.870 mm, širina tovornega prostora: 2.500 mm, vzmetenje: parabolično listje (vzmet), barva: bela, Leto izdelave: 1983, Polpriklopnik CTC ZA90SRT47 Gujdpfey Axufjx Aa Uoc Nizkopodni 11,87 m s hidravličnimi rampami in vitlom (4,10 m + 7,35 m) 3 osi Parabolično vzmetenje Dovoljena skupna masa 47.000 kg – nosilnost 39.000 kg Za specialne prevoze, dovoljena skupna masa kompozicije 56.000 kg Neto izvozna cena: 18.000,00 EUR Vse informacije brez garancije/ možnost napake pridržana.

Stanje: delavnici obnovljeno (rabljeno), Funkcionalnost: popolnoma funkcionalen, lastna masa: 11.200 kg, največja dovoljena obremenitev: 25.600 kg, skupna masa: 36.800 kg, konfiguracija osi: 2 osi, prva registracija: 09/2007, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 500 mm, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245.70 R 17.5, barva: svetlo siva, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2007, Oprema: ABS, Rabljen polpriklopnik culla Bertoja, letnik 2007, 2 osi s hidravličnim krmiljenjem, podaljšljiva culla z osrednjim vzdolžnim nosilcem za dodatnih 4,0 m, zaprta culla dolžine 6,20 m, višina od tal 50 cm, nastavljiv in snemljiv vrat, stranski razširitveni elementi na platformi, idealni za kombajne, pnevmatsko vzmetenje, ABS, ventila za regulacijo višine, tehnični pregled do 31.10.2026 – PRODAJALEC INTERDRIVE SRL – PARMA. Godey A Ih Ispfx Aa Uouc

Stanje: rabljeno, Tehnične podrobnosti: Premer vretena: 150 mm x-pomik: 3000 mm y-pomik: 2000 mm Hod vretena: 700 mm Mere nosilne puše: 340 x 340 mm Izvlek nosilne puše: 700 mm Hod stojala: 1500 mm Priklop vretena ISO: 50 Hitrost vrtanja vretena: 3,2 - 1600 min⁻¹ Velikost mize: 2000 x 2500 mm Maksimalna obremenitev mize: 25000 kg Hitrost hitrega pomika: 5 / 10 m/min Hitrost podajanja: 1 - 5000 mm/min Guodpfxey Anpxo Aa Uec Skupna potrebna moč: 100 kW Približna masa stroja: 57 t Približna potrebna površina: 8,4 x 6,8 x 5,9 m z CNC SIEMENS 840 D popolna B-os aerostatična vodila čelna plošča (3,2 - 140 min⁻¹) kotni rezkalni glavi 1000 Nm hladilna naprava z notranjim dovodom hladilne tekočine (IKZ)

Leto izdelave: 1989, stanje: pripravljen za uporabo (rabljen), Višina konic: 150 mm, razdalja med konicama: 800 mm, največja dolžina brušenja: 400 mm, mere mize X/Y: 1245 mm/200 mm, premer brusilnega vretena: 80 mm, dolžina brusilnega vretena: 400 mm, nosilec obdelovanca: ISO50, hitrost vretena: 8000 obr/min. Dokumentacija na voljo. Ogled na lokaciji je možen. Gujdpfx Aajy D Tp To Ujc

Stanje: novo, številka stroja/vozila: 535119ca408d3bd5a8e74be51, lastna masa: 6 kg, največja dovoljena obremenitev: 11 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring, storage box integrated into turntable front section Foldable rear support Wheel chocks with holders Aluminum side underrun protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) Extendable widening to 3,000 mm (not in rear taper) (Track width of construction machines or vehicles to be transported must not exceed 2,550 mm external frame width), storage compartment for wood planks centered in the loading area, 70 mm planks for widening to 3,000 mm, Tie-down eyes low-bed 3 pairs of lashing points integrated in the floor at the front, each rated for 10 t 6 pairs of lashing mushrooms recessed in the top and sides of the external frame, each rated for 10 t 1x after neck area, rest distributed in between, spacing not greater than 1,200 mm 1x rear taper 5 pairs of ring lashing eyes recessed in external frame, each rated for 5 t (instead of stake pockets) Guodpoi Ri N Hofx Aa Ujc Trailer turntable drawbar Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Twin steel rims, factory silver Braking System 2-line air brake system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, ABS and ALB, with ABS connector at the front, with connecting cable Attention: The trailer must only be towed by towing vehicles that ensure the effectiveness of ABS! Electric system 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white/red width marker lights at rear 2 white position lights at front 1 rotating beacon with bracket, switchable via parking lights (removable beacon) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm 2 x 7-pin fail-safe connectors at the front, with connecting cable Floor Front area steel floor, then 70 mm softwood floor, wheel arch area with steel/tread plate covering Rear taper with 70 mm softwood floor Low-bed area incl. rear taper 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety below, foldable (prevents lateral slipping, not in conjunction with hydraulic side shift) wooden planking with spring assist Operational Notes A special permit is required for an axle load of 10,000 kg. The permit must be applied for individually in each federal state, and the legislator is not obliged to grant approval for a 20 t gross vehicle weight. Customer's risk. The specified gross weight is technically possible, depending on the cargo the gross weight may not be achievable while observing the permitted axle, support, and kingpin loads. Registration / Plates Registration country: Germany EC type approval acc. to 2007/46 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paintwork Frame DB Nova grey Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 195f80ad09517628522e33a91, lastna masa: 7.300 kg, največja dovoljena obremenitev: 16.700 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Rear mudflaps across the entire width Quarter shell fenders in front of 1st axle 1st pair of wheel recesses embedded after the kink in the loading bed area, ramped entry, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! The frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses embedded between the axles in the loading bed area, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The frame in the main beam area is 300 mm higher than the wheel recess. Sliding extensions for widening, extendable to 3,000 mm (not in tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Sliding extensions for widening, extendable to 3,000 mm, also at the bottom in the wheel recesses, foldable at the wheel recess extensions (extension not in the tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) 70 mm timber planks for extension to 3,000 mm Tie-down points on low loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front in the kink, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for attaching tie-down straps) 7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated at 10 t 1x at the front in the kink 6x in the loading bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points no greater than 1,100 mm Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Axles & suspension SAF drum brake axles Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-applied parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, LED side marker lights, 2 white position lights at the front 2 white/red lane guidance lights at the rear 2 x 7-pin fail-safe connectors at the front, with connection cable, 1 LED rotating beacon with holder, switched via side light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Front kink with steel/checkered plate covering Storage box embedded in the ramp to the kink, then with 70 mm softwood floor, in the wheel arch area with steel/checkered plate covering Tail ramp with 70 mm softwood floor Low loading area including tail ramp: 6,500 mm Gjdpoi Ri Rvsfx Aa Ueuc Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring assist Operating Instructions For 10,000 kg axle load an exemption is required, only indivisible loads allowed! The stated gross weight is technically possible, but depending on the type of load, the gross weight may not be achievable within the pe

Stanje: novo, številka stroja/vozila: 2dff0c136c85096f36822a0bb, lastna masa: 7.150 kg, največja dovoljena obremenitev: 16.850 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis - Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring, storage box integrated into turntable front section Gjdei Riy Eopfx Aa Ueuc Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflaps Extendable extensions to 3,000 mm (not at the rear bevel) (Note: The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Central storage compartment for timber boards on the loading platform 70 mm timber boards for extension to 3,000 mm Low-bed lashing rings 3 pairs of 10 t lashing points integrated into the front floor 6 pairs of 10 t lashing mushrooms recessed in the top and side of the outer frame 1 x by the neck area The remaining points are distributed at no more than 1200 mm intervals 1 x at the rear bevel 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (can be converted to 5 t ring lashing eyes, not included) Drawbar Turntable Trailer Coupling Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical Axle load equalisation (rocker balancing) Brake System 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake included 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles ensuring the proper function of ABS! Wheels and Tyres 235/75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver finish Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, followed by 70 mm softwood flooring; wheel arch covers in steel/chequer plate Rear bevel with 70 mm softwood flooring Low-bed area incl. rear bevel 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered, included With spring assist Operating Notes An exemption permit is required for 10,000 kg axle load—only indivisible loads allowed! The specified total weight is technically achievable, but depending on the load, the permissible total weight may not be reached due to axle/support/kingpin limits. (Poor driving and tracking may result from incorrect load distribution) Country of Registration/Plates Country of registration: Germany With Dekra inspection and appraisal (according to §13 EU-FGV) 24/7 service hotline Prepared for double-line license plate holder Contour marking with reflective stripes per ECE R 048, white to the side, red to the rear Paintwork Frame DB 7350 Novagrau 10-year guarantee against rust-through Drawbar galvanized or black, manufacturer's choice Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: ee3256d63dd23b3ad1bdf9ab0, lastna masa: 10.280 kg, največja dovoljena obremenitev: 13.720 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support legs 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Quarter shell fenders in front of the 1st axle Excavator arm trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated at 5 t each in the excavator arm trough, positioned laterally on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear taper 1 storage box recessed into the gooseneck on the floor with lid, W=720 mm/ L=520 mm / D=170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 1600 mm, approx. 400 mm deep. Note! Main frame section 400 mm higher than wheel recess. 2nd pair of wheel recesses between the axles, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 600 mm, approx. 300 mm deep. Note! Main frame section 300 mm higher than wheel recess. Removable wheel recess covers from the main frame, with wooden inserts. Distance from main frame longitudinal member to outside member approx. 1280 mm (wheel recess area) Extensions extendable to 3,000 mm, foldable at the wheel recess extensions (extensions not in the rear taper nor at the bottom of the wheel recesses) (The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber planks centrally on load area or underneath depending on technical feasibility 70 mm timber planks for extension to 3,000 mm Low-bed lashing points 1 pair of ring lashing points recessed in the gooseneck, each rated at 5 t 8 pairs of lashing mushrooms recessed in the top and side outer frame, each rated at 10 t 2 x at the front on the gooseneck 6 x in the low-bed – first lashing point 250 mm from the front, last maximum 250 mm from the rear, distance between lashing points not greater than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each rated at 5 t (can be converted to stake pockets) Drawbar Assembly for Turntable Trailer Drawbar with tested 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension with lift & lower valve, separately operable at front and rear Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Guodpfx Aaji Ri I Nj Uec Steel rims in twin arrangement, factory silver Braking System 2-line pneumatic braking system Spring-loaded parking brake Trailer info center, displays vehicle data (e.g., axle load—not a calibrated scale) and odometer Axle load detection via EBS-Canbus signal, for display in the cab (truck must be pre-equipped, not installed in truck, not a calibrated scale) Vehicle Stability System Duomatic coupling at the front with connecting line to the truck tractor EBS, electronic braking system with EBS socket at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 volts, multi-chamber LED lights with resistor, side marker yellow LED lights, LED license plate lights (Note: Certain towing vehicles may show diagnostic errors despite systems working correctly) 2 white front position lights in LED 2 white/red lane marker lights at the rear in LED Additional LED w

Stanje: novo, številka stroja/vozila: 2b58968e34fac93b429a256e9, lastna masa: 5 kg, največja dovoljena obremenitev: 12 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed trailer Steel welded construction Turntable with robust ball-bearing slewing ring, storage box integrated into turntable front section Rear folding support Wheel chocks with holder Aluminum side underrun protection Full-width rear mud flaps Quarter-shell fenders in front of 1st axle Spare wheel holder for 1 spare wheel, including wheel mounting kit Spare wheel, same brand and specification as standard tires, steel rim Plastic tool box with shelf, w=620/h=360/d=440 mm, lockable with padlock (padlock not included) Lashing rings low-loader 3 pairs of lashing points (10 t each) integrated in front floor, 6 pairs of mushroom lashing points (10 t each) fitted on and into the outer frame at the top and sides: 1x at gooseneck, remaining distributed in between (distance max. 1200 mm), 1x on rear slope 5 pairs of recessed ring lashing points in the outer frame (5 t each, convertible to stake pockets) Drawbar equipment trailer turntable Drawbar with certified 40 mm towing eye Axles and suspension SAF drum brake axles Axle/chassis laser alignment for reduced tire wear and improved fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings Wheels and tires 235/75 R17.5 Manufacturer's choice Steel twin wheels, factory silver Braking system 2-line compressed air braking system Gsdpfei Ri Nxjx Aa Ueuc Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, including connection cable, voltage converter for 12/24 Volt operation Note: Tractor/trailer requires a 7-pin 12 Volt socket! (Electric system with voltage converter required!) Attention: Trailer may only be towed by vehicles that ensure proper ABS functionality! Electrics 24 Volt, multi-chamber lights, yellow LED side lighting 2 white/red width marker lights at rear 2 white position lights at front Additional LED work light at rear, controlled via reversing light 2x 7-pin non-interchangeable plugs at front with connecting cable 1x 7-pin agricultural plug, voltage converter 12/24 Volt (for electrics only, not for ABS/EBS) Floor Steel floor in front section, followed by 70 mm softwood flooring, steel/chequered plate in wheel arch area Rear slope section with 70 mm softwood flooring Low-bed area including rear slope 8,200 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, timber-planked, with spring assist Operating notes Special permit required for 10,000 kg axle load; permit must be obtained separately in each federal state; no guarantee from authorities for 20 t GVW. Customer assumes risk. Country of registration / plates Country: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7-service hotline Prepared for double-line number plate holder Outline marking with reflective tape per ECE R 048, white side and red rear Paintwork Frame DB 7350 Nova grey 10-year corrosion warranty Drawbar galvanized or black, manufacturer's choice Ramps hot-dip galvanized Attention: Archive images!

Stanje: novo, številka stroja/vozila: 408ba9a39bbb8087056d6e563, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Flooring Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Gujdpfxoi Ri Dae Aa Uec Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: novo, številka stroja/vozila: ede0610378cbe39cc4883251d, lastna masa: 24.000 kg, največja dovoljena obremenitev: 7.550 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-loader Trailer Steel welded construction 1st pair of wheel recesses embedded in the driving lane area after the steel platform, bevelled for entry, approx. 1,400 mm long at the bottom, approx. 400 mm deep. Note! Frame is 400 mm higher in the main beam area than at the wheel recess. If machines are to be transported where overall height must be verified, we request a technical data sheet for the machine types with precise specifications (if overall height is exceeded -> customer is responsible, approval required). Depending on ground clearance under the machines, inserts for the wheel recesses may be required on the customer side. Turntable with robust ball race ring, storage box integrated in the turntable front section Rear supports foldable 2 wheel chocks with holder Aluminium side underrun protection Full-width rear mudflap Extending wideners to 3,000 mm (not in rear bevel area) (The track width of the construction machines or vehicles to be transported must not exceed the outside frame width of 2,550 mm) Central storage compartment for wooden planks on loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes low-loader 3 pairs of 10 t lashing points integrated in the floor at the front incl. 6 pairs of lashing mushrooms recessed on top and at the side in the outer frame, each 10 t 1 x at the gooseneck The remaining distributed between, spacing not greater than 1,200 mm 1 x rear bevel 5 pairs of stake pockets integrated into the outer frame, internal 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly trailer turntable Drawbar with tested 40 mm towing eye Gujdpfsi Ri Ryex Aa Uec Axles & Suspension SAF drum-braked axles Axles/chassis laser aligned to reduce tyre and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colour-coded piping for easy service Spring loaded parking brake 2 interchange-proof coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by tractor units which ensure the functionality of ABS! Wheels and tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED illumination 2 white position lights at front 2 white/red track marker lights at rear 2 x 7-pin interchange-proof plugs at front with connecting cable 1 LED beacon with bracket, switched via parking light (removable lamp) 2 pairs of double warning boards, LED-lit and extendable up to 3,000 mm Floor Front area steel floor, incl. Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-loader deck incl. rear bevel 8,200 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring lifting aid Operating instructions For 10,000 kg axle load, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achievable while complying with permissible axle/kingpin/saddle loads. (Poor driving and tracking behaviour possible due to incorrect load distribution) Country of registration / Plates Country of registration: Germany incl. With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for two-line number pla

Stanje: novo, številka stroja/vozila: b50cac2c60a813b0968994fa0, lastna masa: 5.700 kg, največja dovoljena obremenitev: 18.300 kg, skupna masa: 24.000 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Full-width rear mudflap Preparation for widening to 3,000 mm (holes in outer frame, not in rear bevel) Low-loader lashing rings 1 pair of lashing cutouts embedded in the front longitudinal beam at the gooseneck, each rated for 10 t 7 pairs of lashing mushroom pins embedded on top and side of the outer frame, each rated for 10 t 1 x on the front gooseneck 5 x in the low-bed area 1 x in the rear bevel 12 pairs of lashing holes in the outer frame, each rated for 5 t (for lashing strap hooks) 5 x at the gooseneck, 6 x in the low-bed area, and 1 x in the rear bevel Drawbar system for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles, brand as per manufacturer’s choice Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 unmistakable coupling heads at the front, with connecting lines to the truck, Connecting lines extended by approx. 60 cm No ABS, but with mechanical ALB (automatic load-dependent brake valve), thus maximum 60 km/h permit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 7-pin 12 Volt plug at the front with connecting cable, extended by approx. 60 cm 1 LED beacon with holder, operated via parking light (lamp removable) 2 pairs of illuminated and extendable warning plates up to 3,000 mm Floor Front gooseneck with steel/chequer plate covering Toolbox recessed in the drive-over slant to gooseneck Following area with 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-bed loading area including rear bevel: 5,900 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wooden covering Spring-assisted lifting Gjdpfoi Ri Agsx Aa Uouc Operating Instructions For axle loads of 10,000 kg, an exemption permit is required; only indivisible loads permitted!!! The stated total weight is technically possible; depending on the load, the total weight may not be achievable within the allowable axle/support and fifth wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate for max. 60 km/h approval, towing vehicle as agricultural/forestry vehicle (LoF), (for Switzerland, max. 40 km/h possible) Prepared for double-line license plate holder No contour markings / reflective tape according to ECE R 048 Painting Frame: DB 7350 Novagrau 10-year corrosion protection warranty Drawbar galvanized or black, according to manufacturer’s choice Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 15431365fe5515297a6a9fb05, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball-bearing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mud flaps Half-shell mudguards on 1st and 2nd axles with antispray mud flaps behind each axle, antispray mud flaps before and after 3rd and 4th axles Gusdpfx Asi Ri A Sea Ujc Excavator arm recess above the rear axles, extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points each 5 t located in the excavator arm recess on the side at the main frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf insert, W=620/H=360/D=440 mm, can be locked with a padlock (lock not included) 1 storage box recessed into the floor at the gooseneck, with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm 70 mm timber planks for extension to 3,000 mm Storage compartment for timber planks under the loading platform Lashing eyes (40 securing options) 1 pair lashing eyes on gooseneck, each 5 t 9 pairs lashing mushrooms integrated on top and side of outer frame, each 10 t 2 x on gooseneck to the front 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each 5 t (for tension belt attachment) 3 pairs of additional folding lashing eyes, each 10 t 1 x inside next to the main frame at the beginning of the low-bed 1 x on gooseneck (protruding) 1 x recessed behind the last axle Trailer towing device turntable Drawbar with tested 50 mm towing eye, towing eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum braked axles Parabolic spring suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) front and rear Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 Volt, multi-chamber lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable 1 LED beacon with holder, operated via sidelights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel chequer plate covering Followed by 70 mm softwood floor, wheel arch area with steel chequer plate Rear bevel with 70 mm softwood floor Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber overlay Spring-assisted lifting Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for double-line licence plate holder Conspicuity marking with reflective strips according to ECE R 048, white at the side and red at the rear Warning panel according to ECE - 70 Coating Frame hot-dip galvanized incl. passivation, 15-year corrosion guarantee Drawbar galvanized or black, as per the manufacturer's choice Loading ramps hot-dip galvanized Attention! Archive pictures shown!