Tračna žaga

MACC SPECIAL 411 CSO

Stanje: novo, Bandsaw with gravity descent MACC SPECIAL 411 CSO New CE The machine’s fundamental features (blade support rigidity, flywheel sizing, blade guides, blade tensioning) have been thoroughly studied to prevent blade fatigue, increase longevity, and improve cut straightness and speed. – Bandsaw with gravity descent motion of the saw bow controlled by a hydraulic circuit, manual bar feed and vise closing, manual head return – Vertical pivot rotation on play-free, adjustable taper roller bearings – Blade drive with two-speed motor and special gearbox with bronze gear and hardened, ground worm screw – Properly sized flywheels – Robust blade guides made with sealed guide bearings and adjustable carbide wear plates – Blade tensioning achieved via electromechanical device with micro-switch blade rotation control – Vise with rapid approach device – Safety devices on the blade cover, control handle, and blade – Hydraulic cylinder for controlled descent – Cutting thickness: 1.2 mm Fjdpfx Asficb Tobtogc – Cutting range: 45° left, 60° right – Adjustable stop for identical-length cuts – 24V low-voltage electrical system – 0.06 kW electric coolant pump for blade cooling – Base equipped with chip collecting drawer and removable coolant tray – Machine prepared for pallet truck handling

Stanje: rabljeno, Leto izdelave: 2007, Funkcionalnost: popolnoma funkcionalen, Stroj za vrtanje lukenj za moznike URBAN DB 3100, letnik 2007 Fedpfx Abewinq Njtsgc Stanje: zelo dobro - Sistem za vpenjanje profilov in premik vrtalnega agregata upravljan s stopalko - Električni vrtalni motor se ob koncu vrtanja samodejno izklopi - Hitrost podajanja in globina vrtanja sta nastavljivi posamično - Hitro-vpenjalna glava za standardna svedre do max. Ø13mm - Levi in desni podaljšek mize

Stanje: rabljeno, Leto izdelave: 1998, Technical details: Swing diameter: 830 mm Turning length: 4000 mm Swing diameter over bed slide: 540 mm Spindle bore: 130 mm Speed range: 2 - 1,600 rpm Rapid traverse speed: 4 / 5 m/min Feed rate: 1 - 2,000 mm/min Total power requirement: 55 kW Machine weight approx.: 7.5 t Space requirement approx.: 7 x 2.2 x 2 m Equipped with R&D MTC-K cycle control MULTIFIX tool holder, size D Coolant system Fjdpfx Abowwlt Rjtegc *

Stanje: zelo dobro (rabljeno), Leto izdelave: 1982, ULMIA 1710s Table Saw Year of manufacture: 1982 Tilting angle: 45° Cutting length on sliding table: 750 mm Max. blade diameter: 250 mm Max. cutting height: 75 mm Cutting width between saw blade and fence: 650 mm Sliding table with angle cutting scale Fgodpfxsufgnzo Abtjc Table size: 1000 x 630 mm

Leto izdelave: 2001, stanje: skoraj kot novo (rabljeno), Double-aggregate sander, two lower aggregates with 2 x 7.5 kW main motor power, feed motor 4 kW, lifting and lowering motor 2 kW. The machine has been overhauled, the conveyor belt is in very good condition. New graphite shoe. The machine is equipped with two bottom aggregates: the first is a rubber contact roller, the second is a combi system with a graphite pad. Working sanding width is 630 mm. Two feed speeds: slow and fast. Sanding belt length is 1900 mm. Pneumatic oscillation. Pneumatic belt tensioning. Sanding belt speed: 18 m/s. Conveyor belt speed: 9/20 m/min. Number of sanding shoes: 1. CE conformity declaration. Total rated power: 21 kW. Maximum workpiece height: 160 mm. The machine has two lower working rollers. The conveyor belt is positioned above the workpiece. Fgsdpfsfxpbmox Abtoc

Stanje: generalkompletno obnovljen (rabljeno), Leto izdelave: 2011, Rabljena avtomatska hidravlična tračna žaga za kovino MEP SHARK 332 NC EVO Dimenzije lista: 3320x27x0,9mm Kot reza: od 45° do +60° Načini delovanja: ročni, polavtomatski-dinamični, polavtomatski, avtomatski Rezalna hitrost: 15-100m/min (inverter) Kapaciteta reza: pri 0° - okroglo 300mm - kvadrat 260mm - pravokotnik 330x260mm Dimenzije: 2600x2320x2000mm Leto izdelave: 2011 Teža: 1050kg Stroj je v celoti obnovljen in testiran. Fsdpfx Aoul Svlsbtsgc

Leto izdelave: 2002, stanje: rabljeno, Diameter 180 mm Workpiece length 0 mm Workpiece width 1350 mm Fgjdet Hw Shepfx Abtoc Total power requirement 65 kW Machine weight approx. 7,500 kg Required floor space approx. m T I M E S A V E R S (Netherlands) Wide Belt Deburring and Finishing Machine Model 41 Series 1350 WRDOW-N Year of manufacture 2002 Serial No. 2313-03 _____ Sanding width approx. 1,350 mm Max. workpiece height approx. 1 – 50 mm Feed speed variable approx. 1 – 10 m/min Comprising the following units: 1.) Vacuum table with flat workpiece feed belt, 780 mm vacuum track in the center of the belt. Belt feed motor approx. 3 kW, frequency controlled for continuously variable feed rate 1 – 10 m/min. Selector switch for forward and reverse belt run, digital display for belt speed and continuous table height adjustment. Suitable for wet processing. 2.) Contact roller approx. Ø 180 mm x 1350 mm wide, drive approx. 15/19 kW, belt speed approx. 11-22 m/s with fine height adjustment and pneumatic oscil- lation across the width, various sanding belts included. 3.) Vertical sanding/deburring disc (disc brush system) approx. Ø 1200 mm, consisting of self-adhesive nonwoven abrasive in various grades available, specially for deburring and cleaning surfaces as well as for radii rounding on workpieces. Also suitable for workpieces with varying heights. Drive approx. 7.5 kW, disc oscillates motor-driven (2.2 kW) across the entire belt width. 4.) Contact roller approx. Ø 180 mm x 1350 mm wide, drive approx. 18.5 kW, belt speed approx. 11 m/s with fine height adjustment and pneumatic oscil- lation across the width, various sanding belts included. 5.) Wet processing version = complete coolant system consisting of belt filter unit with pump installed in machine base, rotary union on top of the deburring disc spindle, return of coolant via the vacuum table, and water mist separator above the machine, with blower approx. 5.3 kW. Side doors in V2A stainless steel sheet, oil skimmer, etc. 6.) Side-mounted control panel with clear controls and digital position and speed display. Joystick for feed belt and table adjustment, 3 x ammeters, etc. as well as front and rear workpiece pressure rollers, emergency stop Total drive power approx. 65 kW - 400 V – 50Hz Weight approx. 7,500 kg Required room height approx. 3.50 m Condition: good – available for demonstration under power Delivery: ex stock – as inspected Payment: strictly net – upon receipt of invoice

Stanje: rabljeno, Leto izdelave: 2011, Premer reza 260 mm Fgjdpfx Ajwkvq Hobtec Dolžina žaginega traku 3340 x 27 x 0,9 mm Območje reza pri 90 stopinjah: kvadrat 260 mm Območje reza pri 90 stopinjah: ploščat 380 x 260 mm Hitrost traku 37 / 74 m/min Moč motorja žage 1,5 kW Teža stroja pribl. 0,62 t Prostorske zahteve pribl. 1,7 x 1,4 x 1,3 m Poševna tračna žaga - Polavtomatska - Dvojni poševni rez - Zaznavanje materiala pri spuščanju - Vključuje 7 žaginih trakov

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, Power: 1.5 kW, materials: plastic/aluminium, intended use: welding and processing operations, operating pressure: 7 bar, machine dimensions (X/Y/Z): approx. 1500 mm / 1500 mm / 1800 mm, weight: approx. 150 kg. Accessories included. On-site inspection possible. Fgedpfxjukhz Ij Abtsc

Stanje: rabljeno, Leto izdelave: 2016, številka stroja/vozila: 0605-240010, FICEP Flex FRC 1201 Notching System The Ficep FRC 1201 notching and cutting system is part of the modern Ficep Flex series of notching machines. This advanced CNC-controlled notching and cutting system is designed for the fast thermal cutting and notching of H, U, L profiles, flat bars, and square tubes. The steel profile is positioned precisely at the cutting location within the system by a pulling clamping measuring carriage via the roller conveyor. A robotic arm equipped with cutting units (oxy-fuel or plasma) cuts the profiles at the selected positions. The cut or notched finished components either fall into the collection tray or are pushed out of the system by the measuring arm. Thermal Cutting Units: The Ficep profile beam notching system Flex FRC 1201 is equipped for thermal cutting using both oxy-fuel and/or plasma technology. As the plasma power source, a Hypertherm HYPERFORMANCE PLASMA HPR 260 XD suitable for material thicknesses up to 32 mm is used. Thicker materials or bevel cuts greater than 32 mm are processed with the oxy-fuel cutting unit. Transport System: On the infeed side before the Ficep Flex FRC notching system, there is a chain drag cross transporter with a length of 11,150 mm. The profiles (workpieces) can be conveyed in both directions. Subsequently, the profiles are transported into the machine on a robust roller conveyor using a clamping measuring carriage. The system is designed for profiles up to 12 m in length and thus features 12 m roller conveyors with a conveyor width of 1,300 mm on both the infeed and outfeed sides. For the removal of finished components on the outfeed side, there are four chain drag cross transporters, each with a length of 6,450 mm, following the notching system. Mitrol CNC Control and Pegaso Software: The system is operated via a modern CNC control unit from Mitrol. The reliable CNC controller is manufactured by Ficep’s own supplier Mitrol and features Pegaso software, including remote maintenance capability and data transfer interface. Fgedpotwm Ubofx Abtec Torit DCE Filter Unit The extraction filter unit for dust removal is supplied by Donaldson Torit DCE. Safety: Provided by fencing and light barriers Max. profile cross-section: 1,220 x 600 mm Min. material length: 2,500 mm Working height: 865 mm Weight: 7,000 kg Weight of burner unit cover: 1,200 kg This modern Ficep Flex FRC 1201 notching system is in very good condition.