Stroj za brizganje

KraussMaffei KM 900 – 8100 GX

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2019,

Stanje: zelo dobro (rabljeno), Double pump for Krauss Maffei machines Voith Rexroth 3-stage variable displacement pumps Type: SY2DFE1-21/071-071 KM No.: 6441936 MNR: R900751978 Photos are sample illustrations; pumps may vary in color! Pgjdpfxog I Uyce Afaon

Stanje: novo, *TECHNICAL SPECIFICATION: Heating capacity, hot circuit: 48 kW Heating capacity, cold circuit: 12 kW Cooling capacity, hot circuit: 42 kW Cooling capacity, cold circuit: 270 kW Pedpfx Afog Ey Ufsaogn Medium: Water up to 200°C Maximum external volume: 10 liters at 200°C Max. flow rate: up to 200 l/min Max. delivery pressure: up to 6.5 bar Motor power: 5.5 kW Dimensions (LxWxH): 1,395 x 753 x 1,180 mm Weight: approx. 580 kg *EQUIPMENT HIGHLIGHTS: - Control and operation via PLC with touch screen - Heating with stainless steel tubular heaters made of Incolloy - Heater control via solid-state relays - Control cabinet IP54, externally ventilated - Electrical wiring on terminal blocks - Volt-free input for signal to switch between heating/cooling (front door) - Volt-free contact for collective alarm via 3-pin connector (front door) - Temperature control unit with heating and cooling circuits, for connection to a valve station for rapid switching between hot and cold circuits - Temperature-controlled feed of return water - Level monitoring with automatic level compensation - Dirt filters in cooling water inlet and in return line of the circulation system - Separate automatic filling with strainer - Flow measurement using differential pressure principle in both circuits - Monitoring of heating element surface by temperature sensor - System pressure regulation, required compressed air connection: 6 to 8 bar - Pressure boosting pump type DS 360 for make-up water - Corrosion-resistant components (stainless steel, brass) - Unit mounted on castors and ready for connection *OPTIONS: - EcoTemp system for intermittent operation - Connection for external temperature sensor PT100 or type J/K - Remote touch screen with 15 m cable Visit our website for more details or for alternative performance classes. *This unit is compliant with European directives. Other directives and standards are only fulfilled if specified in the order confirmation. This technical specification reflects the standard configuration; customer-specific deviations from the standard are listed in quotations or order confirmations.

Stanje: rabljeno, Leto izdelave: 2021, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: TWT381P3 - 2200374274, hladilna zmogljivost: 72,2 kW (98,16 KM), vrsta vhodnega toka: trifazni, vrsta hlajenja: voda, skupna masa: 1.385 kg, vhodna napetost: 400 V, pritisk: 6 letvica, temperatura: 7 °C, volumenski pretok: 12,3 m³/h, tlak črpalke: 3,46 letvica, skupna širina: 1.150 mm, skupna dolžina: 2.790 mm, skupna višina: 2.020 mm, trajanje garancije: 3 meseci, vhodna frekvenca: 50 Hz, Oprema: Na voljo je tipska ploščica, Special process water chiller / refrigeration unit / water-cooled chiller, Type: TWEevo Tech 381 P3 Manufacturer: MTA S.p.A. The TWEevo Tech 381 P3 is a water-cooled compact chiller, suitable for indoor installation. Features include a crankcase heater, phase monitoring, 60-litre buffer tank, and integrated P3 pump. The chilled water outlet temperature can be set from -10°C to +30°C. Cooling capacity: 72.2 kW [20.5 tons of cooling] Chilled water temp. outlet/inlet (°C): 7 / 12 Flow rate (m³/h): 12.3 Available pump pressure (bar): 3.46 Cooling water temp. outlet/inlet (°C): 45 / 40 Pedpswqfh Uefx Afaogn Refrigerant: R 410A Electrical data: Voltage: 400 V, Frequency: 50 Hz, Phases: 3 Max. power consumption (kW): 39 Max. current (A): 66 Starting current (A): 234 Protection: IP54 Dimensions: Length (mm): 2790, Width (mm): 1150, Height (mm): 2020 Weight empty/filled (kg): 975 / 1385 Connection Rp 2 1/2" Serial no.: 2200374274 Year of manufacture: 2021 Condition: Visual 2, technically OK Used Price: on request in Euros (plus VAT ex Nettetal) – 3-month warranty Used machines may have visual imperfections due to previous usage. (Technical changes and prior sale subject to confirmation!) Location: MTA Deutschland GmbH, 41334 Nettetal

Stanje: zelo dobro (rabljeno), Leto izdelave: 2011, obratovalne ure: 28.000 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.300 kN, For sale is a hybrid injection molding machine, 2-component, brand KraussMaffei, model KM 130-750 CX. The machine is in excellent condition, ready for immediate use, with low operating hours. Equipped with electronic injection and dosing units as well as a hydraulic clamping unit. Technical data: Year of manufacture: 2011 Operating hours: 28,000 h Clamping force: 130 t Cylinder Ø 30 mm / 40 mm (plus 2x 50 mm additionally) Core pull: 1 hydraulic Needle shut-off: pneumatic Tie bar extension: 160 mm Internal pressure sensor Selector valve Transport and loading can be organised Europe-wide at extra cost upon request. Prices are subject to VAT. Pgodpfx Afsu Hxm Uoaon Inspection possible by appointment. Please contact us—our team will be happy to assist you. Trade-in or exchange possible! Machinery Purchase / Sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Do you need a high-quality yet affordable metalworking machine for your workshop? Or do you want to sell yours? For further information or contact options, please visit our website.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036721, vpenjalna sila: 6.500 kN, premer vijaka: 70 mm, razmak između stupova: 1.110 mm, delovna prostornina: 1.078 cm³, tlak vbrizgavanja: 1.877 letvica, injekcijska masa: 981 g, odmični hod: 3.200 mm, višina plošče: 1.540 mm, vrsta pogona: Hydraulisch, prosta razpetina: 3.200 mm, teža orodja: 2.200.000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and versatile stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX guide shoe, forces are optimally absorbed and the service life of your molds is increased. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly, and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM • MC 6 with 24" TFT color display featuring multitouch functions CLAMPING UNIT • Clamping force kN 6500 • Max. mold opening force kN 455 • Clear width (h x v) mm 1110 x 960 • Mounting platen (h x v) mm 1540 x 1440 • Mold installation height, min. - max. mm 1550 (without center plate) • Max. opening stroke mm 3200 • Max. mold opening path mm 1650 • Max. mold weight kg 22000 INJECTION UNIT 1 SP2000 • Screw diameter/type mm 60 / Thermoplastic • Effective L/D ratio 23.3 • Injection pressure bar 2420 • Shot volume cm³ 792 • Shot weight at max. stroke for PS g 720 • Injection speed mm/s 140 • Injection flow cm³/s 396 • Screw drive/rotation speed 1/min 285 • Plasticizing flow g/s 72.2 • Nozzle contact force kN 82 INJECTION UNIT 2 SP2000 • Screw diameter/type mm 70 / Thermoplastic • Effective L/D ratio 20 • Injection pressure bar 1877 • Shot volume cm³ 1078 • Shot weight at max. stroke for PS g 981 • Injection speed mm/s 140 • Injection flow cm³/s 539 • Screw drive/rotation speed 1/min 285 • Plasticizing flow g/s 98.3 • Nozzle contact force kN 82 Pgodpjw U N Ixofx Afasn ELECTRICAL PARAMETERS Connected load kW 341 • Power supply V/Hz 400/50 (3 phases with neutral conductor) WEIGHT AND DIMENSIONS • Net weight t 43.5 • Length x width x height m 11.89 x 3.22 x 2.77 ADDITIONAL EQUIPMENT • Wear-resistant plasticizing unit • BluePower full insulation for plasticizing cylinder • Open nozzle • BluePower ServoDrive • Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) • Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) • Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) • Mold heating: 96-fold (3.5 kW) • Euromap interface for handling: E18 • Euromap interfaces (mainframe): E67, E77, E78, E63, E82.1 • Adaptive Process Control (APC+) • Graphic analysis package • Sliding table with turning unit, servo-driven • Vertical center plate • Parallel closing and opening pressing during the injection process with parallelism control between FWAP and center plate or BWAP and center plate • ColorForm interface: signal interface for integration of an RPM system • Electrical interface for HRS Flexflow system • Electrical interface and hydraulic valves for "1-K dummy operation" • Interface for connection of a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our Parsdorf facility and is available at short notice. Additional options can be offered on request. We look forward to your inquiry.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036936, vpenjalna sila: 800 kN, premer vijaka: 35 mm, delovna prostornina: 135 cm³, tlak vbrizgavanja: 1.837 letvica, injekcijska masa: 123 g, minimalna višina orodja: 150 mm, izmetalna sila: 22.000 N, hod izmetalca: 100 mm, odmični hod: 750 mm, vgradna višina: 400 mm, skupna dolžina: 4.750 mm, skupna širina: 1.670 mm, skupna višina: 1.820 mm, skupna masa: 5.900 kg, ogrevalna zmogljivost: 8,9 kW (12,10 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 470 mm, teža orodja: 600.000 g, Injection moulding machines directly from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines: The base injection moulding machine, precisionMolding, is the perfect entry-level solution for all-electric injection moulding, enabling rapid and innovative responses to market requirements. It combines high performance, user-friendly operation, and short delivery times. The machine can be used across various application areas, such as the packaging industry, electrical and electronics industry, medical technology, and the automotive sector. Your benefits: – Optimised price-performance ratio for a wide range of applications – High energy efficiency thanks to the all-electric machine concept – Fast delivery times realised through basic machine concept with a broad spectrum of options TECHNICAL DATA: KM 80 / 250 PA G01 (Order 38670013) (Machine no.:61036936, new, Year 2023) CONTROL SYSTEM • MC P1 with 15" TFT colour display and multi-touch function CLAMPING UNIT • Clamping force kN 800 • Maximum mould opening force kN 120 • Daylight (h x v) mm 470 x 420 • Mounting platens (h x v) mm 610 x 560 • Minimum - maximum mould height mm 150 - 400 • Maximum opening stroke mm 750 • Maximum mould opening travel mm 350 • Ejector drive electric • Ejector stroke mm 100 • Ejector force forward/back kN 22 / 22 • Ejector speed forward/back mm/s 300 / 300 • Maximum mould weight kg 600 INJECTION UNIT • Screw diameter / type mm 35 / standard • Effective L/D ratio 20.0 • Injection pressure bar 1837 • Stroke volume cm³ 135 • Shot weight at max. stroke (PS) g 123 Pgodpfeuggb Dsx Afaon • Injection speed mm/s 200 • Injection flow rate cm³/s 192 • Screw drive / speed 1/min 382 • Plastification rate (standard screw) g/s 19.5 • Nozzle contact force kN 30 ELECTRICAL PARAMETERS • Connected load kW 17.8 • Installed heating capacity kW 8.9 • Power supply V / Hz 400 / 50, 3-phase with neutral WEIGHT AND DIMENSIONS • Net weight with control cabinet t 5.9 • Length x Width x Height m 4.75 x 1.67 x 1.82 ADDITIONAL EQUIPMENT • Wear-resistant plastification • BluePower full insulation of plastification cylinder • Open nozzle • Air valve, single (BWAP) • Pneumatic control for hot runner shut-off, single • Electrical interface (cascade), 4-fold • Electrical preparation for hydraulic auxiliary unit • Euromap interface for handling, E18, E63 • Euromap interface (central computer), E67, E77 • Water manifold, 4-fold • Automatic central lubrication • Adaptive Process Control (APC) • Injection-compression moulding function • Graphics analysis package • Swivelling device for injection unit The machine is located at our factory in Parsdorf and is available at short notice. Additional optional features can be offered on request. We look forward to your enquiry.

Stanje: rabljeno, Nosilnost: 0/7 kg Pgsdpoh Au I Ijfx Afajn Doseg roke: 1.800 mm Število osi: 6 Ponovljivost: 0,03 mm Teža robota: 380 kg Način montaže: talna

Stanje: dober (rabljeno), Leto izdelave: 2013, vpenjalna sila: 16.000 kN, Oprema: dokumentacija / priročnik, Zapiralna sila: 1600 t Premer vijaka: 135 mm Razdalja med stebri V: 1420 mm Razdalja med stebri H: 1870 mm Prostornina vbrizga: 9662 cm3 Tip: Horizontalen Pogon: Hidravlični Pgedpjyh I Emsfx Afasn

Stanje: rabljeno, Leto izdelave: 2020, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: NTC20 - 14720, hladilna zmogljivost: 21 kW (28,55 KM), vrsta vhodnega toka: trifazni, vrsta hlajenja: voda, skupna masa: 225 kg, vhodna napetost: 400 V, skupna širina: 950 mm, skupna dolžina: 1.080 mm, skupna višina: 1.400 mm, trajanje garancije: 3 meseci, vhodna frekvenca: 50 Hz, Oprema: Na voljo je tipska ploščica, Chiller / Air-cooled Water Chiller Type: NOVATECH NTC 20 NOVATECH Pgedowcflwopfx Afasn The NOVATECH NTC 20 is a compact, air-cooled water chiller suitable for both indoor and outdoor installation, IP 54 rated. Includes shell-and-tube evaporator, 110-liter buffer tank, and built-in circulation pump. Galvanized steel frame, hot-painted with polyester powder coating. Special equipment: - Installed expansion vessel for internal water volume only - Shut-off valve between water inlet and outlet - Flow-regulating valve at water outlet Cooling capacity: 21 kW Chilled water temp. outlet/inlet (°C): 15 / 20 Max. flow rate (l/min): 100 Available pump pressure (bar) max.: 3.3 Ambient temperature (°C): 35 Refrigerant: R 410A Electrical data: Voltage: 400 V, Frequency: 50 Hz, Phases: 3 Ph Max. power consumption (kW): 8.85 Max. current (A): 12.5 Starting current (A): 19 Protection class: IP54 Dimensions: Length (mm): 1,080; Width (mm): 950; Height (mm): 1,400 Weight (kg): 225 Connection: Rp 1" Serial No.: 14720 Year of Manufacture: 2020 Condition: Visual 1-2, Technically ok Used, as new Price: on request in euros (plus VAT, ex Nettetal) – 3 months warranty Used machines may have visual defects due to previous use. (Technical modifications and prior sale reserved!) Location: MTA Deutschland GmbH, 88131 Lindau