Rabljene tračne žage KASTO - krožne žage

KASTO Band- / Bügel- / und Kreissägen

Stanje: novo, Leto izdelave: 2025, Patented mitre system Continuously adjustable cutting speed Hydraulic feed control Hydraulic lifting and lowering of the saw frame Hydraulic material clamping Powerful frequency-controlled saw band drive Swivel range 30° right / 45° left Fodoh S Nxpepfx Afleft Cutting capacity in mm 45° left round 300, flat 300 x 300 90° round 410, flat 620 x 410 45° right round 360, flat 420 x 360 30° right round 300, flat 300 x 300 Remnant piece length without bundle clamping 60mm Recommended options: Micro-spray system Laser line Clamping pressure regulator Powered chip brush Manual lifting roller Setup elements

Stanje: novo, Cutting diameter round: 900 mm Cutting diameter square: 900 mm Cutting diameter flat: 900x900 mm Saw band length: 9300 x 67 x 1.1 mm Table height: 790 mm Band speed: 14 - 60 m/min Total power requirement: 11 kW Machine weight approx.: 8.45 t Dimensions (L x W x H): 4,485 x 1.68 x 3.15 m The semi-automatic, hydraulic saws of the X-tech line offer top-tier sawing technology and maximum performance when cutting specialty steels. - The electro-welded machine frame and the steel saw frame meet all cutting requirements and eliminate vibrations and noise. - The chip conveyor is hydraulically driven and the speed is adjustable. - All machine motions (saw frame, vice, feed, saw band guides) are enabled by modern linear guides with high static and dynamic load capacity, guaranteeing very low sliding friction. - Another key feature is the material positioning rollers, which are powered by a hydraulic motor. These move at a right angle to the material, allowing for optimal clamping. - Thanks to the saw band position height control, the operator can position the band close to the material’s upper edge. After cutting, the band automatically returns to the previous position; alternatively, the 'remain' option in the lower position can be selected. During the cutting cycle, the software compares cutting force with preset values and can stop the sawing system in case of irregularities. - The saw band is cleaned by two adjustable steel brushes, which are hydraulically driven. - The hydraulic unit, including filter and manometer, ensures especially smooth operation at constant pressure. - Precision ground carbide inserts clamp the saw band, complete with lateral, hardened, and adjustable guide rollers. The adjustable band guide automatically moves as close as possible to the material. - The saw band is tensioned by a hydraulic cylinder, controlled by the machine software. Tension is automatically released after a preset time when the machine is idle or after a cycle is completed. - Automatic version with CNC control available for the X-TECH 900 / 1200 models with a feed length of 500 mm for high production series. - The material is supported by a table with seven rollers, powered by a hydraulic orbital motor, allowing precise material positioning even under maximum load. Fodpofg E Hpefx Afloft - All guided motions are facilitated by four ball circulation guides with high static and dynamic load capacities; significantly reduced feed friction. Hardened and ground prismatic guides. Price on request.

Stanje: delavnici obnovljeno (rabljeno), Stock no. 2553 1 used, partially overhauled and function-tested extruder, consisting of: Material hopper Single-screw extruder BATTENFELD type UNI-EX 1-75-25 B Screw diameter: 75 mm – 25 L/D, barrel air-cooled Ffjdpfoiyyndox Afljt Screw speed up to 130 rpm Drive 120 kW – DC (overhauled), drive via belt pulley Heating zone control sections for downstream equipment Control cabinet, melt pressure sensor Inspection / test run possible at short notice by arrangement at our Wuppertal facility. Matching accessories available: > Screen changer > Pelletizing (strand, hot face cut, or water ring) > Miscellaneous Further extruders and complete lines are available for demonstration ex works Wuppertal. We look forward to your enquiry or your visit.

Stanje: novo, Cutting capacity at 90° (round): 350 mm Cutting capacity at 90° (square): 330 mm Cutting capacity at 90° (rectangle): 450 x 320 mm Saw band length: 4250 x 34 x 1.1 mm Band speed: 40 + 80 m/min Table height: 845 mm Ffedjfgyicopfx Aflet Saw blade width: 34 mm Total power requirement: 2.2 kW Machine weight: approx. 0.985 t Space requirements: approx. 1.4 x 2.0 x 2.2 m Double mitre band saw, hydraulic semi-automatic, DGS 350/450 HA-I • Mitre cuts left & right up to 60° without machine conversion • 34 mm saw blade width • Large, ball-bearing supported, rotary worktable • Saw blade guides adjustable over extra-wide linear rails • Heavy-duty, robust gearbox • Large-area clamping plates • Infeed and outfeed roller • Removable chip tray (for cleaning) • Free-standing, safe, ergonomic control panel • Storage space for blades and consumables • Cutting pressure control and feed rate regulator • Fully hydraulic vice • Quick clamping (front loading) • Material height sensor (automatic cut start detection) Semi-automatic operation: 1. Clamp material 2. Start saw 3. Rapid descent to start of material or direct cutting for series cuts 4. Switch off saw band 5. Raise frame just above the material 6. Open vice Optimal, material-independent cutting results through fine adjustment of the saw frame via: * Pressure control valve (cutting force) * Feed rate control valve (cutting speed) * Clearly arranged selector switch with pictograms for intuitive operation

Stanje: kot nova (razstavni stroj), Leto izdelave: 2022, stiskalna sila: 320 t, delovno območje: 4.100 mm, Naprodaj: Baykal Cnc Stiskalnica (320 ton, 4 metre) Proizvajalec: Baykal Kapaciteta: 4 metre x 320 ton Os: R in X os na zadnjem prislonu – 2-osni zadnji prislon Leto izdelave: 2022 Krmilnik: Esa S660W Opremljena z orodjem: Multi V spodnje orodje in segmentirano orodje Tehnične informacije: - Do 12 mm debeline pri 4 metrih / do 15 mm debeline pri 3 metrih - Upogibna moč: 320 ton - 5 osi - Dolžina upogiba (prek orodja): 4.100 mm Ffjdpfxsvgc R Hj Afljt - Dolžina upogiba (med okvirji): 3.550 mm Avtomatsko spodnje podpiranje in laserski sistem za merjenje kota z neposredno povratno informacijo CNC krmilniku za najbolj natančen postopek upogibanja.

Stanje: dober (rabljeno), Spectro CIROS CCD Water Analysis Device - Height: 105 cm - Width: 150 cm - Depth: 75 cm Good condition, fully functional. Can be inspected and tested on site. International shipping available. Inspection: Ffodpfxofiqn Uo Afljt Please note that, to avoid any misunderstandings, the item can be viewed and tested under power before purchase. If you have any questions, please ask them prior to purchasing to prevent any uncertainties. For general inquiries or to schedule a viewing appointment, I am always available at the phone number listed below. Errors in description and prior sale excepted. VAT will be shown separately on my invoices. Shipping via freight forwarder.

Stanje: novo, Bending capacity: 6.0 mm Working length: 3100 mm Material thickness: 8.0 mm Total power requirement: 11.0 kW Weight approx.: 6.7 t Dimensions (LxWxH): 4,88 x 1,16 x 1,18 m Image similar Bending performance: 8.0 mm » at 3x top roll diameter. Pre-bending: 6.0 mm » at 1.5x top roll diameter. Top roll diameter: 230 mm Lower roll diameter: 210 mm Side roll diameter: 190 mm Max. opening: 30 mm Working height: 825 mm Ffodpfx Aod Ab H Hoflst • Fully hydraulic drive of the top and bottom rolls via planetary gearboxes • Digital display for side roll positions • Hydraulic drop-end bearing • Cone bending device • Hardened rolls • Hydraulic adjustment of the side rolls, synchronized via PLC • Hydraulic adjustment of the lower roll via torsion shaft • Pressure-adjustable lower roll • Electric and hydraulic overload protection • Movable control panel • Operating manual in GERMAN and ENGLISH • Machine and equipment in compliance with CE regulations Catalog, see the following link: Important points for cone rolling: • The max. sheet thickness is 50% of the nominal capacity • Cone length must be a max. of 30% or more than 60% of the roll length • Hardened rolls are recommended

Stanje: novo, Cutting capacity at 90°: round 350 mm Cutting capacity at 90°: square 330 mm Cutting capacity at 90°: rectangle 500 x 310 mm Band speed: 15 - 100 m/min Fsdpfx Afofg E Hljlsft Table height: 844 mm Saw blade dimensions: 4250 x 34 x 1.1 mm Total power requirement: 2.2 kW Machine weight approx. 1.2 t Space requirements approx. 1.4 x 2.4 x 1.935 m SPECIAL OFFER PRICE!!! 2-Column Double Mitre Bandsaw K-tech DG 50/33 HA-I • 2-column mitre saw • Robust yet easy to operate • Material height sensor (automatic cut start detection) • Smooth running thanks to angled cut, feed regulator and cutting pressure regulator • Heavy-duty material infeed roller • Removable chip tray (for cleaning) • Energy-efficient and low vibration thanks to angled cut • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 – 100 m/min • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vices • LEDs for monitoring all safety functions • Large-dimension drive wheels (520 mm) dia. • Intuitive mitre angle adjustment up to 60° Semi-automatic operation: 1. Clamp material 2. Saw starts 3. Rapid downfeed to start of material or immediate cutting for serial cuts 4. Saw band off 5. Raise frame just above material 6. Open vice

Stanje: novo, Cutting capacity at 90°: round 510 mm Cutting capacity at 90°: square 450 mm Cutting capacity at 90°: rectangular 650x450 mm Blade speed: 15 - 100 m/min Table height: 844 mm Saw blade dimensions: 5320 x 34 x 1.1 mm Total power requirement: 3.0 kW Machine weight: approx. 2.1 t Space requirement: approx. 1.9 x 2.87 x 1.3 m SPECIAL PRICE!!! 2-Column Double Mitre Band Saw K-tech DG 62/45 HA-I • 2-column mitre saw Fsdped Iipmsfx Aflsft • Robust yet easy to operate • Material height sensor (automatic cut start detection) • Smooth operation thanks to angled cutting, feed control, and cutting pressure regulator • Heavy-duty material infeed roller • Removable chip tray (for easy cleaning/disinfection) • Energy-efficient and low-vibration due to angled cutting • Ergonomic, safe, and free-standing control panel • Frequency-controlled blade drive 15-100 m/min • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vise • LEDs for monitoring all safety functions • Oversized drive wheels (520 mm each) • Clear mitre adjustment up to 60° Semi-automatic operation: 1. Clamp material 2. Start saw 3. Rapid approach down to start of material, or commence series cutting 4. Switch off saw blade 5. Raise frame just above the material 6. Vise opens

Stanje: novo, Leto izdelave: 2025, dolžina tračnega lista: 3.920 mm, širina tračne žage: 34 mm, Double Column Fully Automatic Bandsaw Everising H-260 HB Cutting range round: 0 - 260 mm Cutting range square: 300 x 260 mm Bundle clamping width: 145 – 190 mm Bundle clamping height: 30 – 130 mm Drive power: 3.7 kW Saw blade dimensions: 3920 x 34 x 1.1 mm Weight: 1759 kg Machine dimensions: 2170 x 2100 mm The standard equipment of the machines is as follows: - Sturdy steel construction with double-column design - NC feed system - Infinitely variable, frequency-controlled cutting speed (inverter-controlled) - Digital cutting speed display - Hydraulically operated double horizontal vices - Hydraulic saw blade tensioning - Saw blade guides (including back guide) made of carbide - Hydraulically pre-tensioned blade guides - Precision PLC control system for all hydraulic and electrical components - Cut counter with automatic shut-off - Automatic out-of-stock shut-off - Multi-job function - Bundle clamping device - Powered chip brush - Automatic blade breakage control incl. emergency shut-off - Chip flushing pistol - Flexible work lamp - 2-metre roller conveyor - Tool box - Carbide function Ffedpfsq Ulxyox Aflst Special equipment included: - Variable clamping pressure reduction - Cut deviation monitoring Extensive and complete German documentation.