HSM VK 88 + Stadler KF1800

HSM VK 8818

Stanje: zelo dobro (rabljeno), Leto izdelave: 2015, obratovalne ure: 20.331 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 970 mm, dolžina polnilne odprtine: 1.800 mm, dolžina bale: 1.200 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 750 kg, skupna masa: 33.000 kg, Good day, We hereby offer, subject to prior sale, a used, complete baling line consisting of a baler from the manufacturer HSM, type VK 8818 R-FU including conveying technology and wire tying stations. The following technical data have been taken from the operating manual and manufacturer brochures. We assume no liability for the correctness or completeness of this information. Technical Data Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours, as of September 2025 Number of bales pressed: 29,020 bales, as of September 2025 Main press force: 1,000 kN Specific press force: 120 N/cm² Shear-edge ejector press force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time in idle operation: 8.3 seconds Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length variable from 600 up to 2000 mm Drive capacity: 2 x 45 kW, frequency-controlled Total connected load: 110 kW Total current consumption: 213 A Fuse protection: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Throughput rates at bulk density of 20 kg/m³: 12.86 t/hour bulk density of 50 kg/m³: 32.15 t/hour Bale weight at a bale length of approx. 1.2 m: 650 to 750 kg per bale, depending on material Hydraulic oil tank volume: 2,000 L HVI 46 PLC: Siemens S7-300 Operator panel: Siemens TP 700 Dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Installation dimensions with conveyor technology: 35,000 x 8,480 x 7,745 mm (L x W x H) Weight baler: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional special equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to standard 2 x 45 kW motors at the same output Manual activation/deactivation of wire tying strands to save tying wire with non-expanding materials Shear-edge ejector with 121 kN press force Wire break/end sensor monitoring, with baler shut-off in the event of wire breakage or wire end Bale slide Optical warning signal mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor technology) is in good, immediately operational condition and has been cleaned, lubricated, and maintained weekly by the operator in accordance with the manufacturer’s specifications. Technical Data Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain belt conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Length of feed belt: 7,000 mm Length of ascending belt: 14,500 mm Length of goose neck: 1,550 mm Inclination: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of delivery: - HSM VK 8818 R-FU baler Ljdpfx Ahsyz Af Eoushh - Service platform - Bale slide - Wire deflection stations - Wire spool trolleys (without wire spools) - Stadler KF 1800 chain belt conveyor - Crosswise sliding belt conveyor - Pit cover from the feed conveyor to the pit - Second control cabinet for baler operation at the conveyor - Machine documentation in English Delivery time: The entire plant has already been dismantled and stored, and will be ready for loading shortly after payment is received. We would be pleased if this or one of our other balers is of interest to you. Your service team, Mertens & Frowein GmbH

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2008, A SIG Corpoplast blow molding machine is available. Output: 21,600 bottles/hour; bottle formats: 500ml/750ml/1000ml/1500ml; max. blow air pressure: 40 bar; dimensions (L/W/H): approx. 7000mm/4300mm/3100mm; weight: approx. 20,000kg. Includes Transver AG preform feeder, year of manufacture: 2008, silo, elevator, sorting unit, and chute. Documentation available. An on-site inspection is possible. Lhjdpjt Eu Azofx Ahujh

Stanje: zelo dobro (rabljeno), Leto izdelave: 2015, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, Technical data: Press force: 1,000 kN Specific press force: 121.2 N/cm² Drive power: 45 + 45 kW, frequency controlled Voltage/Frequency: 400 V / 50 Hz Cycle time (idle): 8.3 s Idle capacity (theoretical): 643 m³/h Capacity at 50 kg/m³ (theoretical): 32.15 t/h Feed opening width x length: 970 x 1,800 mm Bale width x height x length: 1,100 x 750 x 600–2,000 mm Maximum bale weight: 700 kg or 800 kg, depending on material The baler feed system includes the following components: - 1 fully enclosed STADLER chain conveyor with associated shaft covers - 1 support structure and maintenance platform for conveyor and hopper - 1 STADLER feeder - 1 automatic channel baler HSM VK8818 R FU (100 t) - 1 wire rack for 500 kg soft wire coils - 10 wire reel trolleys - 1 multi-control system for the baler Ledeygud Aepfx Ahushh - Full set of design documentation and maintenance history - Maintained and serviced by the manufacturer Commissioning upon request. Weight: 33,000 kg Binding type: Wire Processable materials: Plastic film, mixed paper, cardboard, hollow containers made of HDPE/LDPE, and plastic bottles The system is operational and can be inspected while running. The machine will be dismantled on 16.02. and can be inspected at our premises thereafter. Available immediately!

Stanje: dober (rabljeno), Leto izdelave: 2011, obratovalne ure: 40.000 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 88 t, širina odprtine za polnjenje: 990 mm, dolžina polnilne odprtine: 1.800 mm, dolžina bale: 1.200 mm, širina bale: 1.100 mm, višina bale: 750 mm, skupna masa: 23.000 kg, kapaciteta rezervoarja za olje: 2.000 l, moč: 90 kW (122,37 KM), volumenski pretok: 643 m³/h, Good day, We hereby offer, without obligation, a used baling press including conveyor belt, wire tying stations, and bale chute, manufactured by HSM GmbH + Co. KG, model VK 8818 FU. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we do not assume any liability for accuracy or completeness. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours (as of July 2025) Main press force: 880 kN Specific pressing force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length variable from 600 up to 2,000 mm Lodpjymmtcjfx Ahushh Drive power: 2 x 45 kW, frequency controlled Tying: 5-fold horizontal, fully automatic Press dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Installation dimensions including conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used at a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced by a new, larger press in May/June 2026. Until then, the machine can be viewed in operation with material feed. We would be pleased if this press is of interest to you. Your service team, Mertens & Frowein GmbH

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2008, - Stroj v zelo dobrem tehničnem in vizualnem stanju - Takoj na voljo Lhsdpfxsy Dc Nvo Ahush - Prodaja vključuje: - Škarje za staro železo: Zato FCE40 ali Genesis GXP400R - Dvigalo - Dodatna priklopna oprema na voljo po dogovoru

Stanje: rabljeno, Leto izdelave: 1992, Avtomatski stroj za pihanje PET steklenic Proizvajalec: SIDEL Tip: SBO 4 S1 Leto izdelave: 1992 Zmogljivost: 4.000 za steklenice 1,5 L / 2 L Vgrajena moč: 150 kW V kompletu kalupi za 1,5 L Podajalnik preform Tehnično stanje: rabljena naprava, zažene se, program deluje Lsdpswa Rhrefx Ahuehh

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, obratovalne ure: 8.900 h, številka stroja/vozila: LP50VH2, Used Presona LP50 VH2 baler in good operating condition with conveyor belt Technical Data: LP 50VH2 - Theoretical volume capacity: 730 m³/h - Maximum throughput under load: 340 m³/h - Throughput based on material bulk density: * 30 kg/m³ = 7-9 t/h * 50 kg/m³ = 8-9 t/h * 100 kg/m³ = 11-14 t/h - Hopper length: 1500 mm - Hopper width: 1100 mm - Feed chamber volume: 2.7 m³ - Bale width: 1100 mm - Bale height: 720 mm - Bale length: adjustable - Bale weight: 400-550 kg - Number of vertical tying wires: 5 pcs. - Press force: 50 t - Specific pressure: 63 N/cm² - Max. hydraulic pressure: 250 N/cm² - Hydraulic tank capacity: 600 l - Motor power 400 V, 50 Hz: 1 x 45 kW - Oil cooler: 1 x 1.5 kW - Net weight approx.: 16 t - Year of manufacture: 2014 2) Feed Conveyor - Conveyor type: Chain conveyor - Year of manufacture: 2014 - Specifications: * Conveyor width: approx. 1300 mm * Length of horizontal section: 5,500 mm * Length of inclined section: approx. 10,800 mm Ledpfx Ahjyrhi Nsuohh * Conveyor weight: approx. 6 t Scope of delivery: - Baler, control cabinet, operator panel, conveyor belt for sale. The documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete. Viewing available by appointment. We assume no liability for technical information or possible errors. Video material can be provided upon request.

Stanje: generalkompletno obnovljen (rabljeno), Leto izdelave: 2012, Funkcionalnost: popolnoma funkcionalen, moč: 261 kW (354,86 KM), Lindner Urraco U75 D na kolesni osi z magnetom in daljinskim upravljalnikom popolnoma obnovljen Orodja: 6-delni 7/7 diski v Hammel dizajnu (stanje 85 %) skupaj 9800 delovnih ur Leta 2024 vgrajen nov menjalnik, nova hidravlična črpalka, novi hidravlični motorji zdaj približno 600 delovnih ur Lhsdpfx Ahoytdkfoush Izmetni trak prenovljen, magnetni del zamenjan Orodja 85 % Nov servis Nova barva Takoj pripravljen za uporabo

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, obratovalne ure: 37.656 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 85 t, širina odprtine za polnjenje: 1.500 mm, dolžina polnilne odprtine: 1.100 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 650 kg, skupna masa: 25.000 kg, kapaciteta rezervoarja za olje: 1.000 l, leto zadnje generalne obnove: 2024, volumenski pretok: 410 m³/h, transportna širina: 2.400 mm, transportna dolžina: 9.300 mm, Good day, We hereby offer you, without obligation, a used baler from the manufacturer Presona AB, type LP 85 VH1. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we cannot assume any liability for the accuracy and completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours (as of March 25) Main press force: 85 t Specific press force: 100 N/cm² Pre-press door force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Ledpsv T I Evjfx Ahuehh Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Machine weight press: approx. 25 t Note: This machine was used in a recycling facility for compacting paper, cardboard, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have already been replaced in the last 3 years. The machine has been serviced regularly. We would be pleased if this press is of interest to you. Your Service Team, Mertens & Frowein GmbH

Leto izdelave: 2012, obratovalne ure: 1 h, stanje: rabljeno, Transmission: Automatic Power: 1 kW (1 HP) Unladen weight: 20,000 kg For further information, please contact Emal Jaweed. Scrap press, Hassel Ariete 480, Bonfiglioli crane, year of manufacture: 2012. Dimensions: length: 9,600 mm, width: 2,500 mm, height: 2,820 mm, weight: 20,000 kg, engine: 6-cylinder Deutz. Body: hook-lift system / easy relocation. Video available. Additional information: Ledpfx Ahex R T D Douohh * We are offering over 200 units for sale. * Our location is 30 km north of Frankfurt/Main Airport. * Financing & leasing options available. * Specialist for worldwide transport & shipping. * No liability for printing or typographical errors. * Subject to prior sale and errors. * Trade-in possible. * For vehicle and used machinery purchases, only the general terms and conditions of Jaweed GmbH apply. * Further information and our GTCs can be found on our website. All sales are subject to our general terms and conditions (listed: ... / GTC).