Balirni stroj z vključenim transporterjem VK 8818 R-FU

HSM GmbH + Co. KG, Germany HSM VK 8818 F-RU

Technical Data Press:
Manufacturer: HSM GmbH + Co. KG, Germany
Model: VK 8818 R-FU
Year of manufacture: 2012
Total operating hours: 12,078 hours (as of September 2025)
Pump operating hours: 6,616 hours (effective pump runtime)
Number of bales pressed: 65,792 bales (as of September 2025)
Main press force: 880 kN
Specific pressure: 120 N/cm²
Cutter edge pressure relief force: 120 kN
Feed hopper dimensions: 970 x 1,800 mm
Theoretical cycle time (idling): 8.3 seconds
Theoretical throughput: 643 m³/hour
Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm
Drive power: 2 x 45 kW, frequency-controlled
Connected load: 98 kW
Total current consumption: 192 A
Fuse protection: 250 A slow-acting
Tying: 5-fold horizontal, fully automatic
Throughput rates at bulk density of 20 kg/m³: 12.86 t/h
Bulk density of 50 kg/m³: 32.15 t/h
Bale weights at approx. 1.2 m bale length: 650 up to 750 kg per bale, material dependent
Hydraulic oil tank capacity: 2,000 L HVI 46
PLC control: Siemens S7-300
Operator panel: Siemens TP 700
Press dimensions (assembled): 18,000 x 4,300 x 3,270 mm (L x W x H)
Installation dimensions (press with conveyor): 18,000 x 22,000 x 5,765 mm (L x W x H)
Press weight approx. 30 t (main press approx. 20 t, press channel with bale clamp approx. 10 t)

Special machine equipment:
- Access lock with key transfer system
- Electro-hydraulic interlock of the press carriage during tying operation, to prevent press ram movement with highly expansive materials

Additionally ordered special equipment:
- Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to standard 2 x 45 kW motorization, at equivalent output
- Manual activation/deactivation of the number of tying wires, to save strapping wire with non-expansive materials
- Cutter edge relief with 121 kN press force
- Wire monitoring by sensors, including press shutdown in the event of wire break or end of wire
- Bale slide
- Visual warning signal mounted on the control cabinet

Condition of the press:
The complete baling system (baler and conveyor system) is in good, ready-to-use condition.

Dedpfx Adsxcngnshjcn
Technical data for the chain belt conveyor:
Manufacturer: Stadler Anlagenbau GmbH
Type: Chain Belt Conveyor KF 1800
Year of manufacture: 2012
Drive power: 7.5 kW
Conveyor speed: 0.05 – 0.4 m/sec
Feeder belt length: 6,000 mm
Feeder belt side wall height: 400 mm
Incline belt length: 9,000 mm
Incline belt side wall height: 800 mm
Gooseneck length: 1,500 mm
Incline: 30°
Nominal belt width: 1,800 mm
Usable belt width: 1,700 mm
Belt quality: EP-500/4
Steel cleats on rubber belt: 50 x 50 mm
Hollow pin chain, pitch: 125 mm, rollers: 36 mm
Drive shaft height above ground: 4,284 mm
Total conveyor height: 5,765 mm
Transport dimensions feeder belt: approx. 7,000 x 2,200 x 1,250 mm (L x W x H)
Transport dimensions incline belt: 13,000 x 2,500 x 2,900 mm (L x W x H)
Pit dimensions for conveyor: 14,765 x 3,260 x 1,250 (L x W x H)

Scope of delivery:
For sale: the feed conveyor, the baler with bale slide, and the wire feed stations, but without wire.

Remarks:
The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is complete. Inspection possible by prior arrangement. We assume no liability for technical data or possible errors.

Oglas je bil preveden samodejno, zaradi česar je morda prišlo do napak pri prevodu.