Skupina za zbiranje klasja

HOMAG

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2005, Funkcionalnost: nepreverjeno, višina obdelovanca (maks.): 40 mm, največja debelina roba: 3 mm, hitrost pomika os X: 35 m/min, največja hitrost vrtenja: 12.000 obr/min, število mest v zalogovniku orodij: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Buffing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure application with rubber band Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melting device for EVA hot-melt adhesive Laser system (model: LaserTec) Roller set for pressing the edge with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for installation, securing, and use of the machine at the place of destination. Ijdpfx Aoyqybuedkjtd External reference: 5321

Leto izdelave: 2023, stanje: novo, Max. chipping height: 200 mm Infeed width: 500 mm Feed rollers: 3 units Rotor flight circle: 600 mm Chipping length approx.: 20–30 mm Throughput – output: 16–20 cubic meters (solid/cut wood) per hour wood chips Chipper knives: 2 units Feed motors: 2 x 2.2 kW Net weight approx.: 4,100 kg Infeed: horizontal Machine frame: steel, welded with shielding gas Rotor: steel, welded with shielding gas, dynamically balanced Bearing: oversized roller bearings Bearing housings: flanged steel housings Feed rollers: steel, specially toothed Chip discharge: underneath the machine Machine grate (screen): for re-shredding of oversized chips Drive pulley: matched to main motor N = 1,500 rpm Hydraulic system: consisting of a hydraulic pump, membrane accumulator, cylinder, pressure gauge, and control valves for lifting the upper feed roller Itjdpfx Adjncd Azokod Feed: via two geared motors, manufacturer NORD GETRIEBE

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2007, Funkcionalnost: nepreverjeno, delovna širina: 1.935 mm, število vreten: 40, višina plošče: 350 mm, delovna dolžina: 6.200 mm, število osi: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge banding magazines: 3 Number of tools in the tool magazine: 22 (at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Itodpeyqx U Hefx Adkjd Spindles for horizontal drilling in X-direction: 4 Spindles for horizontal drilling in Y-direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Vacuum pods for securing the workpiece Safety mats at the front Vacuum pump Chip conveyor Fixed grooving unit for grooves in X-direction The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and accepts responsibility for installation, securing, and use of the machine at the destination. External reference: 8105

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2005, Funkcionalnost: nepreverjeno, moč: 19 kW (25,83 KM), potovalna razdalja osi X: 4.175 mm, pomik osi Y: 1.730 mm, število vreten: 20, Število orodnih postaj v orodni glavi 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverse beams: 8 Number of tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling in X-direction: 2 Number of spindles for horizontal drilling in Y-direction: 1 Total number of spindles: 20 Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Isdjyttf Sopfx Adkotd CNC controller model: PC85 EQUIPMENT CE marking Front safety cover Note: Cones, cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied as available (left side only). The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 6906

Stanje: rabljeno, Leto izdelave: 2004, WEINIG GRECON DOUBLE-END FINGER JOINT LINE MOD. PJ 150/500 - CE - USED - Infeed wood length: 150 - 700 mm - Wood width: 40 - 150 mm - Wood thickness: 18 - 80 mm Itodpfswry I Esx Adked - Press length: 6100 mm - Pressing force: 120 kN - Milling motor: 15 kW - Scorer: 5.5 kW - Year: 2004 CE

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 4.175 mm, pomik osi Y: 1.550 mm, višina obdelovanca (maks.): 40 mm, število vreten: 30, največja hitrost vožnje: 80.000 mm/min, TECHNICAL DETAILS Travel Range X-axis: 4,175 mm Travel Range Y-axis: 1,550 mm Traverse Speed X-axis: 80 m/min Traverse Speed Y-axis: 80 m/min Traverse Speed Z-axis: 30 m/min Max. Workpiece Height: 40 mm Number of Suction Traverse Bars: 8 Spindles Number of Spindles for Vertical Drilling: 20 Number of Spindles for Horizontal Drilling in X-direction: 10 Total Number of Spindles: 30 Milling Unit Number of Controlled Axes: 4 + Flex5 Motor Power: 15 kW Automatic Tool Changer Liquid-cooled Isdpsyttcwofx Adkstd Saw Unit Tool Magazine 1 Number of Positions: 18 Tool Magazine 2 Number of Positions: 10 EQUIPMENT NC Positioning Suction Units Vacuum Pump PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and technical/commercial documents of descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7350

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, največja debelina roba: 3 mm, hitrost pomika os X: 25 m/min, največja hitrost vrtenja: 12.000 obr/min, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Trimming Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 Ijdpfx Ajytr Hbodketd with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW FEATURES Spraying unit Software for machine programming: PowerControl PC22 CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial descriptive documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6216

Leto izdelave: 2013, stanje: rabljeno, Drying chamber with intermediate ceiling ventilation and front-end wagon loading for the production and conditioning of 3 mm oak lamellae, with initial moisture content of 12 to max. 15% / final moisture content 7% Used, in good condition Manufacturer: Mühlböck Model: ZSWM2110-1180C – 1.0 l/h at 40° C above 30% RH Year of manufacture: 2013 Rated power: 7 kW / 15A Frequency: 50 Hz Control voltage: 24VDC/230VAC Protection class: IP54 Capacity: The chamber holds: - 2 packs in width, each 1.10 m, with 0.20 m spacing - 1 pack in height, 1.80 m, with 0.10 m thick supporting timbers plus a 0.10 m free space - 2 packs in length, each 2.20 m, plus 0.60 m free space The chamber contains 4 stacked packages and has a gross total volume of 17.4 m³. The net capacity is 4 m³ of wood – with a wood thickness of 3 mm and stack batten thickness of 10 mm, utilizing 90% of the width for edged timber. Usable internal dimensions per chamber: Width 2.40 m x Height 2.30 m x Length 5.00 m - Aluminum cassette construction - Aluminum frame - Dimensionally stable rock wool insulation - Aluminum trapezoidal sheeting - Snow load 100 kg/m² - Double-wing swing door - Front-end loading - 2 fans, each 3 kW (D=800 mm) - Stainless steel/aluminum finned tube heat exchanger, 50 kW, flow temperature of 80°C, return temperature 73°C - Servo-controlled supply and exhaust air flaps - Cold water spray system - Chambers operate fully automatically - K5 computer control system Dismantling: Customer location Itedpfx Asvwfhijdkjd Delivery as inspected, in current condition No warranty or guarantee

Stanje: rabljeno, Leto izdelave: 2007, skupna višina: 1.200 mm, skupna dolžina: 3.600 mm, skupna širina: 1.480 mm, - Machine available from: 2025-12-15 - Year of manufacture: 2007 - Documentation available: Yes Itedpfx Adox Ei Syoksd - └ Type of documentation: Technical data, electrical schematics, user manual, operating system - └ Language: NL - CE marking present: Yes - CE certificate available: No - Serial number: - Number of units [pcs.]: 8 - └ 1st unit type: - - Tools included: Yes - └ 3rd unit type: - - Tools included: Yes - └ 4th unit type: - - Tools included: Yes - └ 5th unit type: - - Tools included: Yes - └ 6th unit type: - - Tools included: Yes - └ 7th unit type: - - Tools included: Yes - Voltage [V]: 400 - Current consumption [A]: 50 - Transport dimensions: 3600mm x 1480mm x 1200mm (L x W x H) - Transport packages [pcs.]: 4 Financial Information VAT: The indicated price is plus VAT. VAT/margin taxation: VAT deductible for businesses. Delivery and trade-in possible at any time for all items in the industrial sector. Yorick Diebels

Stanje: rabljeno, Leto izdelave: 2018, skupna višina: 1.650 mm, skupna dolžina: 4.400 mm, skupna širina: 1.000 mm, Price: On request - Special features: - Description: The machine currently has a fault that needs to be fixed - Year of manufacture: 2018 - Documentation available: No - CE marking present: Yes - CE certificate available: No - Serial number: - Number of units: 9 - 1st unit type: - Tools included: Yes - 3rd unit type: - Tools included: Yes Itjdoyvf Nbopfx Adked - 4th unit type: - Tools included: Yes - 5th unit type: - Tools included: Yes - 6th unit type: - Tools included: Yes - 7th unit type: - Tools included: Yes - 8th unit type: - Tools included: Yes - 9th unit type: - Tools included: Yes - Voltage [V]: 400 - Power consumption [A]: 10.3 - Fuse [A]: 16 - Transport dimensions: 4400mm x 1000mm x 1650mm (L x W x H) - Number of transport packages: 1 Financial information VAT: The listed price is exclusive of VAT VAT/margin scheme: VAT refundable for businesses Delivery and trade-in possible at any time for all types of industrial equipment Yorick Diebels

Leto izdelave: 1990, stanje: pripravljen za uporabo (rabljen), Funkcionalnost: omejena funkcionalnost, Ponujamo ta Schiepejev avtomat za zlaganje s 4 stranskimi stenami, letnik pribl. 1990. Priložen je tudi polagalec letev za avtomatsko polaganje do 3 vmesnih letvic z vključenimi zalogovniki. Krmiljenje stroja je bilo leta 2009 obnovljeno in je popolnoma funkcionalno. Tudi mehansko je stroj v osnovi delujoč, vendar bi priporočili zamenjavo določenih komponent. Na stroju tipna ploščica žal ni več prisotna. Možno je odlaganje materiala do dolžine 6,5 m. Dolžina stroja pribl. 7 m. Stroj je bil maja 2025 odstranjen iz naše proizvodne linije in je do takrat deloval. Zaradi starosti se prodaja kot nosilec rezervnih delov brez garancije za delovanje. Proizvajalec: Schiepe Itjdpfxjx Tg Hqe Adkjd Model: Avtomat za zlaganje s 4 stranskimi stenami Letnik: cca 1990 V primeru vprašanj ali potrebe po dodatnih informacijah nam pošljite sporočilo ali nas pokličite.

Stanje: zelo dobro (rabljeno), 3-axis (X-Y-Z) CNC-controlled 'FLEXIBLE' MACHINING CENTER Moving platen (workpiece), static workhead – horizontal platen (workpiece) Control: PowerControl PC86 powerTouch (woodWOP software) Safety enclosure for the working head Itjdpfeyu S I Iox Adksd 2 workpiece clamping cylinders within the working area WEEKE pre-positioning unit for rapid positioning of workpieces in machines with clamping grippers. Support table (workpiece support) at infeed – outfeed table (with powered conveyor belt) With automatic plate pusher Minimum workpiece dimensions (X-Y-Z): 200 x 70 x 8 mm (2 x 4 mm) Maximum workpiece dimensions (X-Y-Z): 3000 x 1000 (option 1300) x 80 mm (2 x 40 mm) Simultaneous processing of two workpieces (in Z-axis) With separate electrical and control cabinet WORKING UNITS (TOP): 2V42, 2H8X/2Y, N2 X-Y90, F2-ETP-6 KW - 42 Independent vertical drilling spindles (drilling head power 2.3 kW) - 10 Independent horizontal drilling spindles (8 in X, 2 in Y) - 1 Grooving saw unit (pivotable 90° in X-Y direction), blade diameter: 125 mm - 1 Vertical main spindle (milling unit) ETP (vertical main spindle power: 6 kW) WORKING UNITS (BOTTOM): 2V42, 2H8X/2Y, N2 X-Y90, F2-ETP-6 KW - 42 Independent vertical drilling spindles (drilling head power 2.3 kW) - 10 Independent horizontal drilling spindles (8 in X, 2 in Y) - 1 Grooving saw unit (pivotable 90° in X-Y direction), blade diameter: 125 mm - 1 Vertical main spindle (milling unit) ETP (vertical main spindle power: 6 kW)

Stanje: zelo dobro (rabljeno), Leto izdelave: 2018, Funkcionalnost: popolnoma funkcionalen, Specifikacija: Dolžina reza: 4300 mm Širina reza: 4300 mm Izmet žaginega lista: 80 mm Upravljalni zaslon na desni strani Delovna miza stroja popolnoma zračno oblazinjena Itsdpfx Adoyuw Umskjd Hitrost programskega prislona naprej: 25 m/min Hitrost programskega prislona nazaj: 90 m/min Standardne spone: 225, 325, 475, 775, 1075, 1825, 3425 mm Power Concept – omogoča sočasno rezanje več trakov z različnimi dolžinami prečnega reza z do 40 % večjo zmogljivostjo Nadzor višine pritisne letve Hitrost vozička žage: 130 m/min Glavni motor žage: 11 kW s pnevmatskim dvigom Predrezovalna enota: 1,5 kW s pnevmatskim dvigom Elektronska nastavitev predrezovalne žage preko upravljalnega zaslona 4 zračne mize: 2160 x 650 mm Tiskalnik etiket 400 V, 50 Hz Upravljalni zaslon na dotik Control Touch Prenos podatkov prek omrežja in USB priključka CE Eco Plus tehnologije omogočajo do 20 % prihranka energije

Stanje: novo, Semi-automatic drilling machine - Precision lift frame for exact drilling results and demanding applications - Infinitely variable feed adjustment with automatic return via limit switch - Two-hand safety operation - Horizontal and vertical workpiece clamping via foot switch - Automatic or manual mode Itoded Rhy Dopfx Adked - Position-accurate adjustment on the Y-axis - Support table right/left with scale and folding stops We would be pleased to provide you with a customised offer tailored to your requirements.

Stanje: rabljeno, Leto izdelave: 2014, CNC-controlled 5-axis machining centre in gantry design for milling and drilling workpieces made of wood or wood-based materials. Console table with 8 consoles Vacuum system WoodWop package for AV-PC LED position display system for manual positioning of vacuum clamps and consoles. Positioning accuracy +/- 2.5 mm 5-axis main spindle, 10 kW Drive5C. Cardanic 5-axis head for milling, drilling, and sawing at any angle. - HSK F 63 interface - Z-axis travel: 450 mm - Liquid cooling with temperature monitoring - Spindle with hybrid bearings for highest precision and long service life - Frequency converter for electronic speed control 0-24,000 rpm - Maximum tool weight: 6 kg incl. holder - Maximum tool length: 230 mm from lower edge of motor spindle - 18-fold disc tool changer underneath Drilling head, 21 spindles, 2.2 kW Vertical spindles: 17 Max. drill diameter: 35 mm Itjdoxvaymspfx Adksd Total drill length: 70 mm Shank diameter: 10 mm Horizontal spindles: 4 One reinforced spindle with adapter for groove saw Max. drill diameter: 10 mm Total drill length: 70 mm Drill shank: 10 mm