HSK HOMAG OBREZNI AGREGAT

HOMAG

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2005, Funkcionalnost: nepreverjeno, višina obdelovanca (maks.): 40 mm, največja debelina roba: 3 mm, hitrost pomika os X: 35 m/min, največja hitrost vrtenja: 12.000 obr/min, število mest v zalogovniku orodij: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Godpfjyqybusx Ab Eotw Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Buffing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure application with rubber band Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melting device for EVA hot-melt adhesive Laser system (model: LaserTec) Roller set for pressing the edge with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for installation, securing, and use of the machine at the place of destination. External reference: 5321

Stanje: kot nova (razstavni stroj), ►►► FRONIUS TPS 3200 SET – OFFER ✅ Scope of Delivery: ➤ Fronius TPS 3200 Power Source (320A TRANS PULSE SYNERGIC) ➤ Fronius FK 4000 FC Cooling Unit – Standard-equipped with Flow Control, Thermocontrol, and coolant filter. The chiller will automatically shut down if the water cooling fails or overheats to protect the hosepack. These features alone cost approx. €400 extra from Fronius. Gtedpfx Abowbil Ss Eew ➤ Fronius VR 7000 Wire Feed Case – Compact and practical – in our opinion, the most sensible feed case; wire is safely stored in a closed case. ➤ Fronius Long Intermediate Hosepack – Each unit is supplied with a 5-meter connection hosepack between the power source and wire feed case for increased flexibility and easier handling. Take the wire feed case to hard-to-reach spots! The hosepack is neatly placed on a hook attached to the side of the machine. (Hooks are custom-made by us) ➤ Fronius Large Trolley – Probably the best trolley with cylinder holder on the market. ➤ Binzel Hosepack – With up/down amperage control on the torch. ➤ Earth Cable 3-4m ➤ New Messer Pressure Regulator ➤ New Drum Adapter for large wire reels This unit can weld almost all materials, including aluminium, steel, and stainless (V2A). It has pulse wire programs and is suitable for MIG brazing (CuSi), commonly used in bodywork and sheet metal workshops. Additional options available at extra cost E.g. Fronius Aw4000/Aw5000 Job Master hosepack (torch display) + EUR 550.00 ----- IMMEDIATELY AVAILABLE PROPER INVOICE Viewing possible in Austria, Vienna 1230! ✔ Insured pallet shipping is no problem! ✔ We are also available via Whatsapp and Viber. ✅Questions✅Questions✅Questions✅ Questions: ✅Questions✅Questions✅ Questions✅ ►►►What is the condition of the units? For your information, we purchase nearly-new used units, fully strip and inspect them, replace wear parts as needed, and only release them for sale after successful test welding. All machines are clean and have no burn or melt holes in the displays, nor are they covered in burn marks or dents! You buy from us an item that is ⭐worth seeing and not worn out! ►►►Do we receive an invoice when purchasing from you? Yes, you will receive a proper invoice. If you have a valid VAT ID and meet the criteria for intra-community EU supply, we can issue a net (tax-free) invoice. ►►►Which payment methods do you offer? Advance bank transfer or cash upon personal collection. ►►►Why buy from us? We are professionals for this series of Fronius welding machines and always keep 60-80 units in stock – exclusively Fronius, no other brands! We are experts with these machines and never sell anything we do not know inside and out.

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2007, Funkcionalnost: nepreverjeno, delovna širina: 1.935 mm, število vreten: 40, višina plošče: 350 mm, delovna dolžina: 6.200 mm, število osi: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Gedpfx Abeyqx U Ho Eotw Maximum panel thickness: 350 mm Number of edge banding magazines: 3 Number of tools in the tool magazine: 22 (at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X-direction: 4 Spindles for horizontal drilling in Y-direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Vacuum pods for securing the workpiece Safety mats at the front Vacuum pump Chip conveyor Fixed grooving unit for grooves in X-direction The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and accepts responsibility for installation, securing, and use of the machine at the destination. External reference: 8105

Stanje: zelo dobro (rabljeno), EINSEITIGER KANTENANLEIMER (links) Kanten (Band auf Rollen) Dicke (min/max) mm 0,3 / 3 Kantenstärke in Streifen / Leisten (min/max) mm 0,4 / 20 Plattenstärke (min/max) mm 8 / 60 NEU (2024) Numerische Steuerung EDGETEQ MOD - Power Touch (WoodCommander) Einstellbare Vorschubgeschwindigkeit bis zu 25 m/min Zuführsystem EZ 14 Sprühvorrichtung (Antihaftmittel) Anschlaglineal, per N.C. verstellbar Vorfräseinheit (vertikale Fugenfräser) 2 x 3 kW Leimeinheit (P.U.R.-Leim + Schnellschmelzsystem) Druckzone für das Band, per N.C. einstellbar Kantenrollen-Halteeinheit (mit 2 Abrollern) Abschneideeinheit HL 84 (2 x ca. 0,5 kW) Pneumatisch schwenk- und einstellbar Grobschneideeinheit BF 20 (2 x ca. 1,5 kW) Gtjdpfeyt Izbsx Ab Eew Multifunktionseinheit (Konturfräsen) FK 11 (2 x ca. 0,4 kW) Konturabzieheinheit Feineinheit (Leimabzieher + Poliereinheit) FA 11 Plattenrückführungssystem "LIGMATECH" Mod. ZHR 541/L/095 (mit Portalbrücke und 360° drehbarem Vakuumkopf)

Leto izdelave: 2022, stanje: novo, Stroj ZIM T1200 lahko proizvaja cevi s premerom 300 mm – 1200 mm in višino 500 mm – 2500 mm z enojnim, dvojnim ali trojnim stiskanjem. Cevi premera 150 mm in 200 mm je mogoče izdelati po posebnem naročilu. Stroji so lahko zasnovani kot polavtomatski ali popolnoma avtomatski, glede na zahteve kupca. Gsdpfjibbikjx Ab Estw Na avtomatskih strojih uporabljamo PLC mikroprocesorje blagovne znamke SIEMENS. Stroj ima bunker za malto in sistem za polnjenje malte. Izdelane cevi se lahko prevažajo do sušilnega prostora s transportnimi vozički ali viličarji. Proizvodnja poteka na proizvodnih paletah. Materiali do premera 800 mm se do sušilnice prevažajo s transportnimi vozički, cevi z večjim premerom od 800 mm pa z viličarjem. Za pospešitev proizvodnje lahko tudi cevi premera nad 300 mm v sušilnico prevažate z viličarjem. Stroj proizvaja z uporabo hidravličnega stiskanja in vibracij. Vibracijski sistem stroja je posebna zasnova inženirjev ZIM ter vključuje oljni hladilni sistem in posebno oljno enoto. Ta sistem je možno elektronsko upravljati. Posebno ojačano ohišje omogoča dolgo življenjsko dobo stroja in zanesljivo delovanje brez napak.

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2005, Funkcionalnost: nepreverjeno, moč: 19 kW (25,83 KM), potovalna razdalja osi X: 4.175 mm, pomik osi Y: 1.730 mm, število vreten: 20, Število orodnih postaj v orodni glavi 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of traverses with suction: 8 Number of tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling in X direction: 2 Number of spindles for horizontal drilling in Y direction: 1 Total number of spindles: 20 Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 Gtodpfxeyttf Ss Ab Eew EQUIPMENT CE marking Safety cover at the front The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for the installation, securing, and operation of the machine at the destination. External reference: 6906

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 4.175 mm, pomik osi Y: 1.550 mm, višina obdelovanca (maks.): 40 mm, število vreten: 30, največja hitrost vožnje: 80.000 mm/min, TECHNICAL DETAILS Gtjdpfeyttcwsx Ab Eow Travel distance X-axis: 4,175 mm Travel distance Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Max. workpiece height: 40 mm Number of traverse beams with suction cups: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X direction: 10 Total number of spindles: 30 Milling Unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid cooled Saw Unit Tool Magazine 1 Number of slots: 18 Tool Magazine 2 Number of slots: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software The machine is sold and delivered in its actual and legal condition ("as seen and approved"), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the place of destination. External reference: 7350

Leto izdelave: 2005, stanje: dober (rabljeno), številka stroja/vozila: C9 15840, Stroj za profilno krtačenje Tagliabue LB 2 Model: LB 2 Gedpfx Aog Rn Iaob Estw TEHNIČNI PODATKI: Leto izdelave: 2005 Tagliabue robni brusilnik s 4 nihajnimi brusilnimi enotami. Dva navpična valja in dva notranja prečna valja za prečno krtačenje.

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, največja debelina roba: 3 mm, hitrost pomika os X: 25 m/min, največja hitrost vrtenja: 12.000 obr/min, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Gtedeytr Hbspfx Ab Eew Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Trimming Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW FEATURES Spraying unit Software for machine programming: PowerControl PC22 CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial descriptive documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6216

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, Edge banding machine from 2006. The HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, allowing for workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It is equipped with a single-sided edge banding unit capable of processing various edge materials up to 20 mm thick. If you are looking for high-quality edge processing solutions, consider the HOMAG Optimat KAL 330 edge banding machine that we have for sale. Contact us for further details. • Line workpiece capacity: • Length: 250–3000 mm • Width: 120–1200 mm • Thickness: 8–60 mm • Edge banding machine (KAL 330) – Base and transport • Solid machine frame; extendable workpiece support with roller rail, ~800 mm • Transport chain, 80 mm wide with rubber pad; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed: 18–25 m/min • Working height: 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece offset/overhang: 30 mm • Workpiece thickness: 12–60 mm • Edge material from strip: 0.4–20 mm (max. cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max. cross-section: PVC 135 mm², veneer 100 mm²) • Max. coil diameter: 830 mm • Pneumatic connection: 7–8 bar • Feed system and control (integrated with KAL 330) • Flexible workpiece feed system wz10 for automatic feeding (longitudinal and transverse); for dimensionally accurate, square parts • Stepless adjustment of infeed guide (axis), speed adjustable at the entry terminal • Automatic lateral adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Entry terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granulate storage • Quick-change system for QA/QE application unit; QA front glue reservoir for color change • Base glue unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max. Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Milling unit HL84 with fixed milling fence for sensitive edges • Pneumatic milling motor adjustment (2 positions: flush/even and with overhang for contour milling) • Pneumatic bevel/straight switching; manual side milling fence adjustment for changing edge thickness • Rough trimming unit: 2 motors arranged vertically, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: rough trimming with approx. 0.2 mm overhang / without overhang • Reserved space for a fine trimming unit • Contour milling unit Servo FK13 automatic: • 2 motors, each 0.4 kW, 200 Hz, 12,000 rpm Gtjdoytf Irjpfx Ab Eew • Servo-driven movements; automatic 8-position tool changer • Feed speed max. 20 m/min; minimum distance between workpieces: 500 mm • Workpiece thickness: 12–60 mm • Automatic FK adjustment for consistent radii with varying edge thicknesses; automatic retraction • FK workpiece guide with additional clamping for min. 120 mm workpiece length (single-sided) • Finishing and cleaning • Multi cleaning system MN21 automatic:

Stanje: novo, Leto izdelave: 2021, Model: i7 Working area: 3048*1524 mm Overall machine dimensions: 4960×2280×2200 mm Laser output power: 3000W / 2000W / 1500W Gtjdjg D Nypjpfx Ab Eow X / Y-axis positioning accuracy: ±0.05 mm X / Y-axis repeat positioning accuracy: ±0.03 mm Max. X / Y-axis linkage speed: 100 m/min 1. Compact design with full protection The small footprint offers full enclosure and enhanced safety. 2. Active anti-collision function Effectively reduces the laser head damage rate, helping you lower maintenance costs. 3. Cast iron bed With excellent vibration absorption, the cast iron bed maintains its shape for long-term durability and optimal mechanical properties. 4. Burr-free cutting for thin sheets The i series can achieve clean edge cuts on thin sheets, ensuring no vibration marks are left.

Stanje: rabljeno, Leto izdelave: 2007, obratovalne ure: 39.359 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 0-201-04-0605, Opis glavne opreme: Vpenjalna miza z matriks aluminijasto konstrukcijo Vakuumski sistem pripravljen za nesting tehnologijo 1000 m³/h Nadzorna plošča Power Control s PC85 Glavno vreteno 15 kW s senzorjem vibracij Godsyucyzspfx Ab Ejtw C-os z agregatnim vmesnikom Vmesnik za agregat FLEX-5 Menjalnik orodij tipa disk z 10 mesti Vrtalna enota: 13 vreten – 9 navpičnih in 2+2 vodoravni Programski paket za pisarniški računalnik Programska oprema WoodWOP Tools Največja hitrost pozicioniranja: 80 m/min v smereh X in Y (vektorska hitrost X/Y = 113 m/min) / 30 m/min v smeri Z

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, This HOMAG KFL 526 / C was manufactured in 2006. The robust double-sided edge banding machine processes workpiece thicknesses from 12 to 40 mm and formats up to 2500 x 1200 mm. The equipment includes a gluing unit, a profile milling unit, and a finishing unit for precise edge processing. Ideal for efficient edge banding at speeds of up to 35 m/min. Contact us for more information about this machine. Additional Equipment • Top/bottom separating agent spraying device / Double hogger unit longitudinal/crosswise: 6.6 kW with electro-pneumatic control / Gluing unit A3 - 2 rollers / Profile milling unit FF12 top/bottom with motors at 12,000 rpm / Finishing unit FA11 top/bottom / Stepless stop cams with a maximum cam overhang of 25 mm / Standard milling unit SF20 6.6 kW / Rough trimming unit 0.55 kW • PUR Nordson melting station / tool set / extraction duct Machine advantages Technical machine advantages Gtsdpfex U Uzrex Ab Ejw • Workpiece thickness: 12 - 40 mm / minimum workpiece size (LxW): 250 x 240 mm / maximum workpiece size (LxW): 2500 x 1200 mm / maximum workpiece weight: 50 kg • Edgebanding tape thickness: 0.4 - 3 mm / maximum edge cross-section (plastic): 135 mm² / maximum edge cross-section (veneer): 100 mm² / maximum roll diameter: 830 mm • Longitudinal processing speed: up to 35 m/min for thin edges up to 0.6 mm / up to 30 m/min for thick edges up to 3 mm • Cross processing speed: up to 30 m/min for panel dividing / up to 20 m/min for edge processing • Minimum workpiece spacing: 500 mm

Stanje: zelo dobro (rabljeno), Leto izdelave: 1999, Zapiralna sila: 25 ton Razdalja med stebri: 270x270 mm Največja odprtina: 275 mm Višina orodja: 200 mm Velikost orodne plošče: 400 x 400 mm Gsdpovl Skgsfx Ab Estw Premer polža: 18 mm Volumen vbrizga: 20 cm3 Masa brizga: 17 g Tlak vbrizga: 2500 bar Delovne ure: 38.035 h

Leto izdelave: 2011, stanje: pripravljen za uporabo (rabljen), Glavni pogon Število osi: 3 Ta 3-osni stroj HOMAG WEEKE OPTIMAT BHX 500 je bil izdelan leta 2011. Ponaša se z robustnim CNC obdelovalnim centrom z delovnim območjem 2500 mm x 1300 mm, glavno elektro vreteno ima moč 6 kW, največja debelina obdelovanca pa je 80 mm. Vključuje 84 vrtalnih vreten in dvojni rezkalni vreteni, vsaka z močjo 6 kW pri 18.000 vrtljajih/min. Če želite kakovostne CNC zmogljivosti, razmislite o stroju HOMAG WEEKE OPTIMAT BHX 500, ki je na voljo za prodajo. Za več informacij nas kontaktirajte. Vrste uporabe Gsdpfx Abjx D Nvgs Ejtw CNC obdelava lesa