Obdelovalni center

HOMAG BAZ

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2003, število osi: 4, največja hitrost vretena: 18.000 obr/min, This 4-axis HOMAG PROFI BAZ20/30/16/V/D was manufactured in 2003. It is equipped with Homatic CNC control, WOODWOP CNC programming system, an 18-position disc tool changer, and a main spindle with a 12 kW three-phase motor. The machine can process workpieces up to 3,000 mm in length and 1,400 mm in width and is fitted with a full-length table with adjustable vacuum clamps. Ask about the availability of this HOMAG PROFI BAZ20/30/16/V/D CNC woodworking center. Contact us for further details. • Control/Software: Homatic CNC controller; WOODWOP CNC programming system; Postprocessor • Workpiece capacity: • Length: 800–3,000 mm; Width: 350–1,400 mm; Max. thickness: 70 mm with edge / 80 mm milling • Minimum rail width: 120 mm; Max. weight: 150 kg • Table/clamping: • Full-length table (D-table) • Longitudinal console 1 fixed; Longitudinal console 2 adjustable manually in Y-direction • 8 vacuum clamps, 125 x 50 x 100 mm • Working height, bottom edge of workpiece: 950 mm • Unit for shifting vacuum clamps on carrier rail with pneumatic extension console (max. 4 clamps per longitudinal console) • Width adjustment (longitudinal console/D-table): Servo drive, per longitudinal console • Stop pins for laminate overhang: lifting/rotating device, max. 20 mm overlay, stroke length 110 mm, individually selectable, end-position monitored (for manual door loading) • Main spindle: • Speed range: 1,500–18,000 rpm (VFD 15 kW), full rated power from 12,000 rpm • Max. tool diameter: 180 mm (milling) / 200 mm (sanding); dust extraction for all tools/units • Unit interface/C-axis: • Pneumatic and tiltable drive interface • C-axis with torque drive and 3-point support • Tool changer: • 18-position disc tool changer for HSK F63; tool weight 6 kg; max. tool length 200 mm • Configurations: 18 x max. Ø 130 mm; or 9 x max. Ø 180 mm + 9 x max. Ø 70 mm; sanding tools max. Ø 200 mm • Toolchanger raised for traveling pickup (left side) • Units (for tool changer unless stated otherwise): • Drilling/milling unit, 4 spindles: ER25 up to shaft Ø16 mm, max. projection 50 mm, max. speed 13,500 rpm, continuously tiltable via C-axis Fgodpfxjzt Avrj Apref • Lock case milling unit, 2 spindles D=16/20: counter-rotating, 12,000 rpm, integrated air blast, unlimited tilt over C-axis • Tilting saw/drilling unit: manually 0–90°, flange Ø30 mm, cutting body Ø52 mm, prepared for crosscut saw max. Ø 180 mm, drill chuck with Weldon D=10 mm, max. speed 9,000 rpm, C-axis tiltable • Cutter holder D=30 with chip guide: arbor length 45/80 mm, chip deflector plate controlled via C-axis, changer space Ø 140 mm • Edge trimming unit: simultaneous top/bottom, edge radius max. R12 mm, min. external radius ~R5 mm / internal radius ~R30 mm at 90°, scanning top/bottom/side, unlimited C-axis tilt, max. speed 12,000 rpm, workpiece thickness max. 50 mm, min. overhang ~35 mm, with narrow sensing shoes • WPL cutterhead: exit angle 5°, Ø 70 mm • Edgebanding/gluing equipment: • Drive spindle/V for gluing units: mounted on the right side of the gantry; cross-slide with Y return lock and Z-axis lift; return lock with C-axis and electric/electronic interface; own Z-axis • Gluing unit for 4 sides, 90 mm (for main spindle): straight edges with direct glue application; 1 pre-press roller + 1 pneumatic post-press roller (programmable); minimum internal radius R40 at 90°; max. edge height

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, število kartuš s črnilom: 10, število tiskalnih glav: 2, EPSON SureColor S80600 10.000 m² Fgsdpfx Aoym A Uvoprof RIP Caldera Ploter Summa S1D140 2 novi tiskalni glavi, manj kot 6 mesecev stari Zelo dobro ohranjeno, možnost priprave za transport in pakiranje v zaboj po dogovoru. Cena na zahtevo.

Stanje: rabljeno, Leto izdelave: 2005, Funkcionalnost: popolnoma funkcionalen, Oprema: CE označba, HOMAG OPTIMAT BAZ211 VENTURE 20 (Rezalni glava št. 5) Letnik proizvodnje: 2005 Osnovna konstrukcija in pogoni • Strojna miza: Močna, stabilna konstrukcija s kompaktnimi linearnimi vodili. • Pogoni osi X in Y: Digitalni AC servomotorji in zobniki s prednapetjem za brezhibno delovanje. • Pogon osi Z: Digitalni AC servomotor s krogličnim vijakom, hod je 535 mm. • Mazanje: Ročno centralno mazanje za vse pogone in linearne vodila. Glavni vreten in os C • Moč: 11 kW pri načinu S6 (7,5 kW pri S1). • Hlajenje: S tekočino hlajen vektorski krmiljeni asinhroni motor. • Območje vrtljajev: Neprekinjeno programirljivo od 0 do 18.000 vrt/min. • Namestitev: HSK F63 po DIN 69893. • Os C: Opremljena z vmesnikom za dodatne naprave, vmesnikom za pneumatiko in 3-točkovno podporo. Sistem za vpenjanje (konzolna miza) • Konzole: 6 kosov z dvokrožnim vakuumskim sistemom brez cevi. • Opora: 6 vzdolžnih opor na konzolah (hod 140 mm) in 2 nastavljivi stranski opori. • Oprema s priseski: • 10x dvosmerni vakuumski priseski (160x115x100 mm), od tega 4 z integriranim dvigalom. • 2x dvosmerni vakuumski priseski (125x75 mm). • Pnevmatski sistem: 4 priključki z enokrožnim sistemom za mehanične objemke. Delovne dimenzije obdelovanca • Dolžina (X): Max. 3050 mm (posamična nastavitev) ali 900 mm (nihačen način delovanja). • Širina (Y): Max. 1220 mm za rezkanje; max. 1150 mm za vse dodatne naprave. Fgedjzr N H Uepfx Aprjf • Debelina (Z): Max. 60 mm s standardnimi priseski; do 300 mm, vključno z objemkami za zgornje rezkanje. • Minimalna debelina: 12 mm za faziranje, 16 mm za oblo rezkanje. Menjalnik orodij in dodatne naprave • Tip: Diskovni menjalnik (12 mest) za orodja in dodatne naprave HSK F63. • Kapaciteta premera: 12x max. 135 mm, ali kombinacija 6x 180 mm in 6x 85 mm. • Vakuumski sistem: Rotacijska vakuumski črpalka z zmogljivostjo 66 m³/h (enakovredno 100 m³/h pri lamelnih črpalkah). Nadzorni sistem (Power Control PC85) • Strojna oprema: Industrijski računalnik (2 GHz) z 512 MB RAM, trdim diskom za podatke in drugim za varnostno kopiranje (kloniranje). • Programska oprema: • woodWOP: Grafični vmesnik za CNC programiranje. • woodDesign: 3D vmesnik za načrtovanje pohištva. • woodScout (opcijsko): Grafični diagnostični sistem. • Komunikacija: Omrežna kartica Ethernet in modem za oddaljeno diagnostiko.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2010, Funkcionalnost: popolnoma funkcionalen, rabljeno CNC obdelovalno središče s 4 osmi Proizvajalec: Homag Tip: BAZ 211 Venture 21L Letnik: 2010 Pomembne lastnosti! - Agregat Flex 5+ - Agregat PowerEdge za lepljenje - Vrtalna glava MPU - in še več. Konzolna miza z 8 ročno nastavljivimi konzolami, vsaka z 2 sesalniki, stranskim in vzdolžnim pritrdilnim vijakom, LED prikazovalnik za vakuumske sesalnike 6 tirnic za dvigovanje, vakuumska priključek za šablone PARAMETRI OBRAZCA: Fodpfx Apjzp Edqerogf – Dimenzije obdelovanca/delovna miza: 4175*1550 mm – Debelina obdelovanca: – Največ 300 mm, vključno z vpenjalnimi pripomočki za frezanja; z običajnim vpenjalom največ 60 mm; lepljenje: največ 40 mm – Do največ 60 mm z običajnim vpenjalom VARNOSTNE IN ZAŠČITNE NAPRAVE: skladno z direktivo ES; VARNOSTNA OGRAJA NA DESNI STRANI Z VRATI na levi in zadnji strani: stenska montaža! Oprema: 18 kW vreteno in 18-kratni menjalnik orodij (krožnik) + 10-kratni menjalnik krožnikov, C-os in vmesnik za agregat Flex5+ Vrtalna glava MPU s 30 vreteni (V20/H10/S360°) (integrirana nagibna os 0-185°) Agregat Flex5+ za žaganje/vrtanje/frezenje Paket za lepljenje Power Edge 360° z vnaprejšnjo postajo za obrezovanje in 1 valj Šoba za pihanje ob robu obdelovanca 2* kombinirani agregat za obrezovanje/frezenje po krivulji Mesto za menjavo orodja na desni strani VAKUUMSKA ČRPALKA 100/140 M3/h Krmilnik: POWERCONTROL PC85 NADZORNA KONZOLA ZA ZAGON PROGRAMA; WOODWOP različica 6.0 DOKUMENTACIJA IN BESEDILA ZA NADZOR: NEMŠČINA Dobava vključuje samo prikazana orodja in HSK vpenjalnike!

Stanje: novo, Leto izdelave: 2024, dolžina gredi pod glavo: 80 mm, dolžina navoja: 55 mm, največja hitrost vožnje: 480 mm/min, Flat Die Thread Rolling Machine E.W. MENN GW63 Fully refurbished to as-new condition. New guides, vibrator, and vibratory discharge system. New electrical system with inverter and PLC. Thread size: M8x80/55 mm. Throughput: 480 pcs/min. Threading diameter (min./max.): 3 - 8 mm. Die length: 115/130 mm. Fgsdpfxot Uucao Aprsf Machine available for inspection and testing at HBR srl - Calolziocorte (LC).

Stanje: rabljeno, številka stroja/vozila: 008495, Delovno območje os X: 3050 mm Fjdpfxsy Edqqj Aprjgf Delovno območje os Y: 1400 mm Delovna površina: z vakuumskimi konzolnimi nosilci Moč glavnega vretena: 11 kW Število kontroliranih osi: 4 osi Največja višina roba: 45 mm Število vrtalnih vreten: 21 Število mest za orodja: 12

Stanje: zelo dobro (rabljeno), Leto izdelave: 2003, Funkcionalnost: popolnoma funkcionalen, - Leto izdelave: 2003, začetek obratovanja: 2004 - Delovne mere: 4000x1600x200 mm - Glavno vreteno: 7,5 kW - C-os - Lepljenje agregat - Svedri: 12x vertikalno Fedpfx Apeza Uryeregf - LED prikaz položaja priseskov - Orodjarna: 12 mest

Stanje: delavnici obnovljeno (rabljeno), For Sale: EOS P100 – Ready for Immediate Use This EOS P100 has been fully inspected and refurbished, making it ready for immediate deployment in your production environment. Fodpfx Apsrm Tdwsrsgf Included in the scope of delivery: • 2 build platforms • Set of hoppers Specifications: • Technology: SLS (Selective Laser Sintering) • Material class: Polymers • Compatible materials: PA2200, PA3200, PA2201, Inframotion PA12, TPU, and more. • Build volume: 200 x 250 x 330 mm • Laser type: Synrad 48-3, 30W CO2 laser • Minimum wall thickness: 0.4 mm Included services: • Transport & Installation: Secure delivery in original EOS packaging as well as professional installation. • Warranty & Maintenance Plans: Flexible options tailored to your specific requirements. About Inframotion 3D (IM3D) At Inframotion 3D B.V., we specialize in high-quality refurbished EOS SLS machines with comprehensive support. As the only provider offering a complete solution for pre-owned EOS equipment, we stand out for our extensive expertise and unique services. What we offer: • Expert Service: Installation, maintenance, repairs, and upgrades carried out by experienced former EOS technicians. • Exclusive Materials: Cost-effective, high-quality consumables such as our plug-and-play PA12, developed specifically for EOS systems. • Comprehensive Support: From transportation to maintenance plans – we take care of everything. Count on IM3D for reliable machines, premium-quality materials, and the expertise to optimize your SLS production. KNOW WHAT YOU'RE BUYING! Completely refurbished and with warranty! Feel free to contact us for further information or inquiries!

Stanje: rabljeno, Leto izdelave: 2011, številka stroja/vozila: 0-201-50-1289, obratovalne ure: 7.062 h, potovalna razdalja osi X: 6.000 mm, pomik osi Y: 1.400 mm, model krmilnika: POWERCONTROL PC 85, višina plošče: 300 mm, največja hitrost vretena: 24.000 obr/min, CNC machining center for milling, drilling, and edge banding! The machine must be collected between 10.06.26 and 30.06.26! TECHNICAL DETAILS Working range X-axis: 6,000 mm Working range Y-axis: 1,400 mm Maximum panel pass-through height: 300 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Number of controlled axes: 5 axes Number of work zones: 4 Maximum edge height: 65 mm Number of drilling units: 1 Total number of drilling spindles: 21 Total number of vertical + horizontal spindles: 25 Number of milling spindles: 2 Total number of tool changer positions: 77 Barcode reader model: DATALOGIC Worktable and Workpiece Clamping Number of rails: 12 Number of pumps: 1 Fsdsy Uviwopfx Aprsgf Vacuum pump flow rate: 300 m³/h NC positioning Vacuum cups for workpiece clamping NC positioning of vacuum cups Drilling unit Drilling unit 1: Top Vertical drilling spindles: 21 Horizontal drilling spindles in X: 2 Horizontal drilling spindles in Y: 2 Total number of vertical + horizontal spindles: 25 Milling units Milling spindle 1: Top Number of controlled axes, milling spindle 1: 5 Motor power, milling spindle 1: 15 kW Spindle speed, milling spindle 1: 24,000 rpm Automatic tool changer Milling spindle 2: Top Number of controlled axes, milling spindle 2: 4 Automatic tool changer, milling spindle 2: Yes Motor power, milling spindle 2: 11 kW Spindle speed, milling spindle 2: 12,000 rpm Edge banding unit Number of edging units: 1 Maximum panel height: 60 mm Model: POWER EDGE 360° Positioning: Mounted on the main machine beam Number of edge roll magazine positions: 2 Gluing unit Glue pot for hot-melt adhesive Hot-melt pre-melter Tool magazines Number of tool magazines: 4 Positions in tool magazine 1: 72 Location tool magazine 1: Rear of the machine Positions in tool magazine 2: 2 Location tool magazine 2: Rear of the machine Positions in tool magazine 3: 2 Location tool magazine 3: Rear of the machine Positions in tool magazine 4: 1 Use for tool magazine 4: Only for saw unit D:350 mm MACHINE DETAILS Control system: WINDOWS 10 Machine programming software: POWERCONTROL PC 85 EQUIPMENT Pod and rail worktable NC-positioned workpiece clamping Vacuum cups Vacuum pump Top drilling unit 2 milling spindles POWER EDGE 360° edge banding unit Glue pot for hot-melt adhesive Hot-melt pre-melter Edge roll magazine 4 tool magazines DATALOGIC barcode reader Protective net Chip conveyor CE marking Safety mats The machine is sold and delivered in its actual and legal state ("as seen and approved") based on photographic documentation and technical/commercial documents of descriptive nature. The buyer has the right to inspect the goods prior to collection and accepts responsibility for the installation, securing, and use of the machine at the destination. External reference: 8527

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, Funkcionalnost: popolnoma funkcionalen, WoodWop7.1 (posodobitev opravljena leta 2018, plačana cca 9.500 €) Delovno območje X: 4000 mm Delovno območje Y: 1600 mm Elektromandrin z osjo C, moč 11 kW, vpenjanje HSK 63F Glave za vertikalno vrtanje: 17 Horizontalna vrtalna glava v križni postavitvi + žaga Enota za rezkanje in čeljenje Enota za 360° lepljenje Kombinirana enota za obrezovanje/strganje Magazin za robni trak z 2 mesti Fodsyprr Nepfx Apregf Krožni magazin z 12 pozicijami Krmilnik: Power Control PC 85 Delovna miza z 8 prečnimi letvami z vakuumskimi priseski Vakuumska črpalka Elmo Rietschle Varnostne preproge Transportni trak za ostružke Vključuje 4 agregate (čelilna žaga, obrezovalec, kombinirani strgalo/obrezovalec, horizontalni 4-izhodni vrtalni agregat) in priseske. Samo cca 4.100 delovnih ur. Stroj v odličnem stanju Na voljo takoj

Leto izdelave: 2015, stanje: novo, We have a MATICA Espresso card printer available. The new price is around €1,599, now available for €999. Fgedpfx Aefnldqspref Year of manufacture: 2015. The printer has always been on display in our showroom; we have printed perhaps 10 cards with it and then decided that this type of system is not suitable for our company. That’s why it is now practically brand new and available for sale. Single- or double-sided edge-to-edge printing Optional magnetic stripe and smart card encoder Ethernet connectivity, optional WiFi Prints up to 850 cards per hour 100-card feeder The Matica Espresso II is a compact yet powerful desktop card printer that combines Italian design and engineering with German reliability for consistently high performance. The Espresso II offers excellent value and versatility, exceptional print speeds, and outstanding print quality. Its robust, durable construction is ideal for both office use and card production environments. The Espresso II is a single-sided desktop ID card printer, perfect for projects where only one side of the card needs to be printed. The printer can be easily upgraded in the field to duplex printing, doubling your card output without requiring additional hardware. On-site upgrades are also possible for contact and contactless smart card encoding. LED status indicators on the front allow you to monitor the production process from a distance, while the blue LED light on the card hopper door shows real-time card input availability. Optional single card manual insertion is available for individualized printing, and each printer features a rear output hopper for efficient handling of large print runs. The flexible setup, with front input and output trays as standard, saves space—perfect for desktop, cabinet, or under-counter installations. Each Espresso II also offers options for integrated magnetic stripe, contact chip, or contactless smart card encoders, making it suitable for a wide range of applications such as access control, time & attendance, payment systems, and more. The complete product line includes Ethernet as standard and optional WiFi for easy, convenient printing and encoding. You can configure your printer to match current requirements and later add features as your needs evolve. This new printer line is ideal for diverse applications, including employee and membership ID cards, service and benefits cards, gift and loyalty cards, access control cards, student IDs, and transit passes, among others. Espresso II is available with various configurations—modules, encoding options, colors, etc.

Stanje: rabljeno, Leto izdelave: 2012, moč: 7,5 kW (10,20 KM), potovalna razdalja osi X: 4.000 mm, pomik osi Y: 1.550 mm, pomik po osi Z: 300 mm, število mest v zalogovniku orodij: 12, No. 3274 CNC Machining Center HOMAG PROFI BAZ 222/40/F/K Used, year of manufacture 2012 Working area X: 4000 mm Working area Y: 1550 mm Fgodpfx Asy S Edxoprof Working area Z: 300 mm 1 milling spindle Main motor 7.5 kW Maximum speed 24,000 rpm Tool holding system: HSK-F63 12 tool changer positions 17 vertical drilling spindles 2 horizontal drilling spindles X 2 horizontal drilling spindles Y Grooving saw, 90° swiveling Edge banding unit Separate Y-axis Console table, 6 consoles Vacuum pump Sale on behalf of customer, ex location near 71063 Sindelfingen, without disassembly, transport, or installation. Disassembly, loading, and transport by us available as an option. Description and price subject to change without notice. To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended. Sale is made in as-is condition. Technical details, condition description, year of manufacture, and scope of delivery according to manufacturer's brochure or previous owner, without guarantee. Subject to prior sale. For used machines, any warranty is excluded; the following applies: “purchased as inspected.” Images and videos are for reference only and do not represent the actual scope of delivery. Payment terms: Prices plus statutory VAT; payment before collection or shipment required. Delivery terms: ex location.

Stanje: dober (rabljeno), Leto izdelave: 2006, Funkcionalnost: popolnoma funkcionalen, CNC MACHINING CENTER WITH EDGE BANDING UNIT AND ASSOCIATED POST-PROCESSING UNITS. Technical specifications: Fjdpfx Aoy Hrh Teprjgf Working dimensions: + X-axis: 3,050 mm in single occupancy + X-axis: 900 mm in pendulum operation + Y-axis: Milling up to 1,220 mm with tool diameter 25 mm Edge banding up to 1,220 mm All units up to 1,170 mm Workpiece thickness up to 60 mm with standard clamps 6 workpiece consoles for hose-free vacuum system 4 workpiece stops in X-direction, integrated into the machine carrier, for large workpieces 6 workpiece stops in X-direction, one per console One workpiece stop each left & right in Y-direction 4 lifting rails for easy positioning of heavy workpieces LED setup assistance for easy positioning of vacuum cups and consoles Equipment: Milling spindle 11 kW, HSK F63 Speed 0 - 18,000 rpm Liquid cooling C-axis for use of processing units, with torque transmission and 3-point support 12-position tool change magazine Drilling head with 17 vertical spindles Spindle spacing 32 mm Air blow nozzle to clean workpiece edges Interchangeable edgebanding unit for 360° edgebanding from butt joints. With single-roll magazine With granulate feed Edge thickness up to 3 mm Adapter units: + Horizontal drilling head, cross-head design + Lock case milling unit, 2 outlets + Saw unit 90 degrees + Swiveling drilling/sawing unit + Combination radius milling / scraper unit Control: POWERCONTROL with: WOOD WOP AV license WOODWOP

Stanje: dober (rabljeno), Funkcionalnost: popolnoma funkcionalen, double tenoning and double drilling machine, step-by-step Equipped with: 1+1 saw units 1+1 milling units Fgjdpfx Aew A A E Ioprsf 1+1 drilling units Maximum length: 2500 mm

Stanje: zelo dobro (rabljeno), CNC MACHINING CENTER (POINT-TO-POINT) – 4 Axis (5 Axis with FLEX 5) Gantry-type machine (mobile in X-axis) Control System: Powertouch (PC85) with woodWOP software Safety enclosure for the working head Clamping table with modular K-Table consoles Fgodpfxow Dc Nie Apref Consoles support arms (qty.): 8 Clamping table dimensions (mm): 1340 Automatic positioning of consoles (X-axis) LED display for programmed vacuum cup positions (Y-axis) Workpiece clamp Automatic power tool change system – POWERCLAMP Disc tool changer – magazine capacity (qty. tool stations): 18 Maximum working area (X – Y – Z): 4000 x 1550 x 60 mm Maximum working area for edging (X – Y – Z): 4000 x 1500 x 60 mm Working area – vacuum pump (capacity in m3/h): 100/140 Chip conveyor Separate electrical and control cabinet Total connected load (52 A) WORKING UNITS (TOP): No. 17 independent vertical drilling spindles (High Speed 7500) No. 4 independent horizontal drilling spindles (2 on X axis + 2 on Y axis) Drilling head motor power (kW): 2.2 No. 1 vertical main spindle (milling unit) HSK 63 (kW: 15) Edge banding unit Power Edge (Y-axis), edge banding aggregate (hot melt glue + premelter) Edge material (rolls) thickness (min/max): 0.4 – 3 mm Edge magazine for rolls (1 compartment) Premilling station (cutting unit) No. 1 crossbeam unit (4 horizontal drilling spindles) No. 1 circular saw unit (diam. 125 mm) Combination unit (flush milling/profiling scraper)