Ekscentrični pritisk - enojni stolpec

HENSEL EBU H 80 RIV (UVV)

Leto izdelave: 1990, Stanje: rabljeno, Pressure: 75 t Outreach: 300 mm Stroke: 8 – 110 mm Table surface: 750 x 600 mm Ram adjustment: 75 mm Ram surface: 430 x 230 mm Through-hole in table: 250 x 150 mm Pin hole in ram: 40 mm Stroke rate: 60 + 90 strokes/min Machine weight: approx. 4.4 t Total power requirement: 4.5 – 6.8 kW Space requirement: approx. 1.95 x 1.1 x 2.35 m Distance table/ram with stroke down, ram down: 19 mm Distance table/ram with stroke up, ram up: 380 mm Equipment: - With hydraulic clutch-brake combination, new hydraulics and oil cooler Kdedod Nl E Uspfx Afnow - With gear train in oil bath - Fixed table prepared for mounting of tool change consoles - 2 roller strips in the table - Mechanical overload protection in ram (shear plate) The following works are carried out on the machine / Partial overhaul: - Machine completely disassembled, inspected, seals replaced, defective parts exchanged, etc. - Machine repainted - New Balluff cam switch - New hydraulic unit with oil cooler for clutch - New Vogel central lubrication system - New control cabinet with touch panel and ABB safety control - Current UVV safety inspection with brake time measurement

Stanje: rabljeno, številka stroja/vozila: 51568, Pressure: 100 t Stroke: 0–500 mm Table surface: 800 x 650 mm Ram surface: 800 x 600 mm Table through-hole: 355 mm Table height above floor: 800 mm Installation height: 1130 mm Machine weight approx.: 5.7 t Throat depth: 310 mm Space requirement approx. LxWxH: 1.2 x 2.0 x 3.67 m Installation height specified with ram at top dead center. Kdodpfscxxrrex Afnjw Machine will be retrofitted to comply with new safety regulations: Safety distance: 270 mm / Overrun speed measurement: 135 mm/s, Overrun distance: 44 mm.

Stanje: rabljeno, Leto izdelave: 1970, Pressure: 63 t Throat depth: 250 mm Stroke: 8–100 mm Table depth: 710 mm Table width: 500 mm Ram dimensions: 450 x 280 mm Ram adjustment: 63 mm Strokes per minute: 140 spm Kodjcxxx Hopfx Afnodw Total power requirement: 7 kW Machine weight approx.: 3.5 t

Leto izdelave: 1965, Stanje: rabljeno, Pressure: 150 t Outreach: 550 mm Stroke: 10 - 140 mm Table surface: 1180 x 980 mm Strokes per minute: 40 Installation height: 500 mm Ram surface: 1040 x 800 mm Ram adjustment: 70 - 150 mm Pin hole (depth x diameter): 435 x 55 mm Power requirement: 15 kW Machine weight: approx. 12 t Space requirements: approx. 3 x 1.7 x 3 m - with additional brake - ram weight compensation Kodscubatopfx Afnedw - motorised ram adjustment - central grease lubrication (manual) - break plate - table clamping plate - safe for manual feeding operations - operating manual available

Leto izdelave: 1988, Stanje: rabljeno, številka stroja/vozila: 103.071.3156.78192, Saw blade diameter: 400 and 425 mm Cutting capacity at 90° round: 130 mm Cutting capacity at 90° square: 120 x 120 mm Mitre cutting capacity at 45° round: 130 mm Kjdpfx Afez N Amenedw Mitre cutting capacity at 45° square: 110 x 110 mm Cutting speeds: 11 and 22 m/min Feed rates: 670 mm/min Cut-off length: with automatic feed up to 1200 mm Electrical connection: 380 V, approx. 4 kVA Saw drive: 1.6/2.5 kW Space requirement: 1800 x 3800 x 2000 mm Weight: approx. 1800 kg

Leto izdelave: 2002, Stanje: rabljeno, Pressure: 63 t Reach: 315 mm Stroke: 8–100 mm Stroke rate: 140 strokes/min Ram adjustment: 63 mm Table surface: 1200 x 630 mm Ram surface: 800 x 315 mm Through hole in table: Ø 110 mm Table height: 820 mm Ram bore: Ø 50 mm Installation height: 335 mm Total power requirement: 7.5 kW Machine weight: approx. 5 t Pneumatic clutch-brake combination Centralized oil lubrication Hydraulic overload protection Manual stroke adjustment Manual ram adjustment Kedpfx Aolp U D Tsfnedw Two-hand operation Foot control Roller block strips in table Hydraulic clamp on the ram Counterbalance cylinder Approved for manual loading operations

Stanje: rabljeno, Leto izdelave: 1970, številka stroja/vozila: 120895, Pressing force: 63 t Throat depth: 250 mm Stroke: 8 - 100 mm Strokes per minute: 120 s.p.m. Table: 715 x 500 mm Installation height: 330 mm Ram adjustment: 63 mm Ksdpefx Hv Hefx Afnsdw Clamping plate: 700 x 480 mm Pass-through opening in the table: 240 mm Pass-through opening in the clamping plate: 110 mm Ram clamping surface: 450 x 280 mm Machine weight approx.: 5.5 t Required floor space approx.: 1.2 x 1.7 x 2.7 m Single-column eccentric press in tiltable design, via hydraulic adjustment system, tiltable in 4 stages, pass-through opening to the rear (325 x 500 mm) or downward (360 x 160 mm), with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot release can be configured, operation mode selector for continuous or single stroke setup, emergency stop switch, piece counter, various accessories.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 1980, Pressing force: 300 t Table size: 1,200 x 850 mm Throat depth: 400 mm Ram width: 1,100 mm Table opening: 400 x 250 mm Installation height: 500 mm Strokes per minute: 32 1/min Kdjdpfx Asd A Hbcofnsw Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: approx. 19,500 kg Other features - Approved for manual loading operations - Equipped with Herion safety valve Xsz 20 - Motorized central grease lubrication - Pneumatic ram weight compensation cylinder - Motorized ram adjustment - T-slots in ram - Free-standing control panel - Connecting rod bearings overhauled

Leto izdelave: 1987, Stanje: zelo dobro (rabljeno), številka stroja/vozila: 31700987, Technical Data Manufacturer: Stiefelmayer Model: SMM-C Kodpefd Dr Hefx Afnjdw Year of manufacture: 1987 Measuring Range X-axis: 2500 mm Y-axis: 1000 mm Z-axis: 1200 mm Other Features Measurement Counter: MZ200 (retrofitted in 2014) Column cross-section: 100 x 100 mm Horizontal arm cross-section: 60 x 60 mm The machine can be modernised with new accessories according to customer requirements. Price: on request! Installation and commissioning possible! We would be pleased to provide you with a detailed offer! Note: Our offer is directed exclusively towards professional clients! (Subject to modifications and errors in technical details, specifications and prices, as well as prior sale!)

Stanje: kot nova (razstavni stroj), Leto izdelave: 2021, številka stroja/vozila: 06 61 218, Ref. No.: Lg 32821 Single-Sided Decoiler BBT ABH 2000/400 Exhibition machine, unused Machine No.: 06 62 218 Year of manufacture: 2021 Technical Data Load capacity approx.: max. 2,000 kg Strip width: max. 400 mm Inner coil diameter: approx. 450 to 520 mm Outer coil diameter: max. 1,500 mm Unwinding speed: approx. 2 to 15 rpm Equipped with adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase gear motor. Expansion of carrying segments manually via hand crank and joints Number of carrying segments: 3 Coil lateral guidance achieved by robust, lockable boundary arms. Decoiler stand constructed in heavy-duty box design, fabricated as welded assembly. Additional Equipment: Shutdown for "loop too small" via antenna switch, mounted on the column of the base housing of the loop control. Height infinitely adjustable. Kjdpfx Afog U Utvsnjdw Strip side guide on the base housing of the loop control, via lateral guide rods. Pass-through width infinitely adjustable.