Stolpno žerjavno žerjavno žerjavno žerjavno žerjavno žerjavno žerjavno žerjavno žerjavilo Verižno dv

Demag KBK Kran Drehkran Hallenkran L 3m Demag KBK1 250Kg + Demag PK Kettenzug

Leto izdelave: 1979, stanje: rabljeno, številka stroja/vozila: RS82/12, Technical Data: 1x Demag KBK 1 pillar-mounted slewing crane, rated capacity 250 kg, with PK chain hoist Load capacity at full outreach: 250 kg / 0.25 t Height: approx. 3 m Underside of jib: approx. 2.5 m Jib outreach: 3 m Hook height: approx. 2 m Total weight: approx. 350 kg Equipped with 250 kg chain hoist Including bolts, cable trolley, trolley, end cap, etc. Slewing range: 300°, Connection: 400V 16A Crane is dismantled and immediately available Item location: 75053 Gondelsheim, Germany Additional cranes available, load capacity 80–5000 kg – please enquire See photos Hodpfxsvv N Auo Af Ten Shipping via freight forwarding or collection by appointment only

Stanje: rabljeno, številka stroja/vozila: 87 54 41 57, Grinding wheel diameter: 200 mm Grinding wheel width: 30 mm Grinding wheel bore: 51 mm Grinding wheel speed: 3000 rpm Electrical connection: 380 V, 630 W Required space: 600 x 260 x 320 mm Hsdpfedc Swujx Af Ten Weight approx.: 23 kg

Stanje: novo, Load capacity 500 kg Number of suction cups: 6 Diameter of suction cups: 215 mm Vacuum Lifter VH 6-500 For horizontal transport of smooth, dry, and airtight panels. Robust load-bearing structure made of steel, painted in RAL 2000 with low dead weight. Consisting of: - 1x Galvanized longitudinal beam, length 2,400 mm - 3x Galvanized crossbeams, each 1,000 mm in length - 6x Spring-mounted, articulated, and adjustable suction cup holders - 6x Suction cups Ø 215 mm; in case of wear, the sealing ring can be replaced separately from its metal carrier, cost-effectively and without tools - 6x Ball valves for individually shutting off each suction cup, enabling smaller formats to be lifted without moving the suction cups or beams - 1x Spiral connection cable, small coil: * extendable to 3,500 mm, version as extension cable with CEE plug and coupling * routed next to the load chain to the hoisting device - Low-maintenance, high-quality, dry-running rotary vane vacuum pump with a suction capacity of 8 m³/h and a final vacuum of 85% (150 mbar) - Electrical connection: 3-phase 230/400 V + PE, 50 Hz, with cable (approx. 0.5 m long) and CEE plug (16 A). Isolation transformer integrated into the control system (necessary if the vacuum lifter is connected via the crane trolley and there is no neutral conductor) - Extendable operator handle to 1,000 mm from beam center. Sturdy metal pouch for your crane control included at no extra charge. - Operation "Suction / Release" via manual slide valve: Wear-free and highly robust manual slide valve for safe suction and release after pressing the release button (double-action release according to EN 13155) - Control and safety unit for vacuum lifter: * Robust control box * Contactor circuit for the vacuum pump * Safety warning device with audible signal * Vacuum gauge with danger zone indication * Large vacuum reservoir with safety non-return valve * Double-action operation for load release - Fine dust filter to protect the vacuum pump - Comprehensive and easily understandable documentation - Warranty on material and manufacturing defects: one year in single-shift operation (excluding wear parts) Hsdpfxeq Sc Aus Af Ten Initial inspection according to UVV 18, VBG 9a with CE declaration of conformity according to EN 13155 - Packaging suitable for truck transport.

Stanje: rabljeno, Clamping Plate – Table of a Long Planer Machine – Table Width / Clamping Width: 1845 mm Table Length / Clamping Length: 5505 mm Hedpfxebn Amfo Af Tsn 7 longitudinal T-slots for T-slot nuts: M30 T-slot spacing: 263 mm Total length: 6230 mm Total plate height: 350 mm Weight: 11 t

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, leto zadnje generalne obnove: 2025, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced Hjdpfsvf E Avsx Af Tsn - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2000, obratovalne ure: 25.000 h, potovalna razdalja osi X: 10.300 mm, pomik osi Y: 2.000 mm, pomik po osi Z: 1.800 mm, hitrost pomika os X: 10 m/min, hitrost podajanja osi Y: 10 m/min, hitrost podajanja os Z: 10 m/min, položaj glave za glodanje: 2.5 x 2.5 °, največja hitrost vretena: 3.000 obr/min, hitrost vretena (min.): 60 obr/min, širina mize: 3.300 mm, dolžina mize: 12.000 mm, montažni premer: 50 mm, skupna višina: 48.750 mm, skupna širina: 100.000 mm, skupna dolžina: 212.000 mm, skupna masa: 100.000 kg, Duplex-Fräsmaschinen bestehen aus zwei Maschinen, die einander gegenüber angeordnet sind und entweder separat oder als eine Einheit betrieben werden können. Das Werkstück kann dabei mit zwei simultan arbeitenden Spindeln bearbeitet werden. Produktivitätssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen, also Einzel-Fräsmaschinen Verbesserte Bauteilgenauigkeit, da die Bearbeitung in den meisten Fällen in nur einer Aufspannung erfolgt Ein einziger Bediener kann die DUPLEX-Fräsmaschinen steuern Geringerer Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Schnelle Amortisation der Investition aufgrund der hohen Produktivität DUPLEX-Lösungen ermöglichen verschiedene Konfigurationen: Einzelner Arbeitsraum oder Pendelbearbeitung Geeignet zur Bearbeitung von Baggerarmen/-auslegern wie z.B. von CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Achse: 10.300 mm Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Hedpfxjrx Rxts Af Tjn Spindelleistung: 22/30 kW Spindeldrehzahlen: 60 - 3.000 min⁻¹ Spindelaufnahme: 50 ISO / BT / MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf, automatisch indexierend: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg

Stanje: novo, Load capacity in kg: 1000 kg Reach: 4000 mm Height: 3000 mm (underside of jib) Total column height: 3790 mm Slewing range: 270 degrees Total weight: approx. 525 kg Description: - Festoon cable power supply for trolley - Drag chain, cable sag approx. 800 mm - Operation from floor using pendant control Including: - ABUS electric chain hoist - Chain hoist type GM 4 1000.5-2, double-strand - Painted in RAL 5017 traffic blue - Lifting capacity 1 t - Hook travel 3000 mm - Maximum hook position 2442 mm - Design basis FEM 9.901 - Mechanism group 2m / M5 - Lifting, 2-speed (pole-switchable) 1.3 / 5 m/min - Lifting power 0.22 / 0.9 kW - Duty cycle 60% ED - Switching frequency 360 c/h Overload protection The crane system complies with the requirements of Machinery Directive 2006/42/EC as well as current UVV regulations DGUV Regulation 52 (formerly BGV D6). Included: - Anchor rods L200 (set) size LS 200 Hjdoxak Hxspfx Af Ton - Consisting of 8 pieces M27 mm x 800 mm with 1 steel template (500/8) - For foundation anchoring, including grouting accessories For alignment of the slewing jib crane, a mounting gap between the column base and the building floor must be provided. The mounting gap is to be grouted by the customer after approx. 4 weeks of crane operation. Illustration shows a similar crane system.

Stanje: novo, Leto izdelave: 2025, nosilnost: 1.000 kg, various very heavy-duty welding tables, machined, partially plasma-nitrided Hedswu Exzopfx Af Ten Sizes: - 1 x 1 meter, €1,500 - 1.2 x 1.2 meters, €1,700 - 1.5 x 1.5 meters, €1,900 - 2 x 1 meter, €2,300; plasma-nitrided €3,300 - 2.4 x 1.2 meters, €2,900; plasma-nitrided €3,900

Stanje: rabljeno, Leto izdelave: 2006, Technical details: Swing diameter over bed: 500 mm Swing diameter over cross slide: 290 mm Turning length: 850 mm Distance between centers: 850 mm Longitudinal travel (Z axis): 900 mm Cross travel (X axis): 260 mm Control: Manuaplus 4110 Spindle speed: 10 - 3000 / 2x stepless rpm Spindle torque: 920 Nm Spindle bore: 70 mm Cross travel (X axis): 8 m/min Longitudinal travel (Z axis): 10 m/min Operating hours (machine on): approx. 34,600 h Tailstock taper ISO: MT 5 Tailstock quill stroke: 180 mm Total power requirement: 24 kVA Machine weight approx.: 5.2 t Machine dimensions approx. (LxWxH): 2.2 x 3.2 x 1.9 m Multifix toolholder size C Hodpfx Aewtct Hjf Ton 3-jaw chuck Ø 250 mm Chip tray Manual hour counter Live center in tailstock Operation via control panel and monitor Accessories: 4-jaw chuck Ø 250 mm with internal jaws Various chuck keys Machine lighting 8x leveling pads 4x wedge lifters Various pairs of jaws 1x steady rest Ø 100 mm, closed type

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, Manufacturer: Spinner Model: TC-400 Year of manufacture: 2014 Control: Fanuc 32iTB Max. bar capacity: Ø 52 mm Equipment: Short bar loader Spinner Servo-Load 80-1500V2 with support stand Control: Fanuc 32iTB with color LCD screen/operator panel 1 Drive motors for X/Z axes and spindle by GE Fanuc, digital AC technology, travels: X = 200 mm, Z = 515 mm, main spindle up to 5,000 rpm / 52 mm; power 18 kW; torque 113 Nm (S6 = 40%), main spindle as integrated motor spindle with water cooling, spindle nose A6, C-axis for spindle including software option "Transmit" for face machining and "cylindrical interpolation" for cylindrical surface machining, hydraulic hollow clamping cylinder, 12-position turret for tool holders in accordance with DIN 69880/30 mm, 12 live tool stations with turret for milling and drilling operations, tailstock for TC400, Morse taper 4, Hedpfx Aowwucusf Tjn Chip conveyor TC400, with enlarged L-shaped coolant tank, approx. 150 liters with centrifugal pump 50 l/min, 3.3 bar Parts catcher, tool probe arm, high-pressure pump, electrostatic air cleaner