Linija za odpiranje bal BO 4000

Cross Wrap Oy Ltd., Siilinjärvi, Finnland BO 4000

Leto izdelave: 2011, stanje: pripravljen za uporabo (rabljen), A shredder manufactured by Gross Apparatebau GmbH, previously used in the wood industry, is available. Feed opening (X/Y): 600mm/800mm, hopper volume: 0.6m³, rotor diameter: 252mm, rotor length: 600mm, rotor speed: 90 rpm, drive power: 18.5kW, number of knives: 14, screen perforation: 10mm–40mm, extraction nozzle diameter: 160mm, machine dimensions (X/Y/Z): approx. 1800mm/1200mm/1650mm, weight: approx. 1300kg, operating hours: 4578h. Documentation is available. On-site inspection possible. Hodpfx Aeu Nlkxof Ten

Stanje: skoraj kot novo (rabljeno), The MSP 120 ZK is optimally suited for the crushing and subsequent briquetting of various types of metal chips. The MSP 120 ZK briquetting press with integrated shredder consists of a hydraulic chip briquetting press and a pre-installed crusher, precisely matched to each other. This system enables the size reduction and compaction of chips generated by turning and milling operations. The volume is significantly reduced, and the briquettes are separated from the coolants (coolant emulsion, oil) absorbed during previous machining processes. The system consists of a feed hopper into which the material to be processed is loaded, and an integrated shredder that reduces the chip length. A conveyor system continuously and gradually feeds the shredded chips into the hopper of the chip press via a conveyor belt. There, two augers transport the material into the compaction chamber. The system features a monitored liquid collecting tank and a pump. The cooling fluids can be returned to the production process. Cycle control is managed by a PLC and an electronic level sensor for monitoring the fill level in the hopper. Optionally, a tipping device can be added for manual loading if required. Briquetting Press: Throughput (Aluminum): 15–20 kg/h Throughput (Steel, Copper): 45–60 kg/h Briquette Ø: 60 mm Productivity: 120–180 pcs/h Hsdjw R Ranopfx Af Ten Specific pressure on briquette: 1,050 kg/cm³ Motor pump power: 7 kW Total installed power: 10 kW Voltage: 400 V / 50 Hz Oil tank: 80 l Dimensions: 1,400 x 1,200 x 1,050 mm Weight: 800 kg Shredder: Cutter shaft: 1 pc Motor power: 5.5 kW Number of knives: 16 pcs Knives replaceable: Yes Knife size: 25 mm Knife material: Hardened steel Shaft length: 400 mm Screen size: 20 mm Hopper diameter: 1,000 mm Hopper volume: 1 m³ Weight: 280 kg Power supply: 380 V Overall system dimensions: 2,820 x 1,862 x 2,065 mm Colour: Textured lacquer RAL 7035 light grey

Stanje: novo, Bernardo Universal Lathe Titan 660 x 2000 Technical Specifications Centre distance: 2,000 mm Centre height: 330 mm Swing diameter over bed: 660 mm Swing diameter over gap: 900 mm Swing diameter over cross slide: 460 mm Bed width: 400 mm Spindle bore: 105 mm Spindle mount: DIN 55029, D1-8 Speed range (16): 25 – 1,600 rpm Longitudinal feed range (25): 0.044 – 1.48 mm/rev Cross feed range (25): 0.022 – 0.740 mm/rev Metric threads (54): 0.45 – 120 mm Hodpfxsfbbx Rs Af Tsn Inch threads (54): 7/16 – 80 TPI Quill diameter: 90 mm Quill travel: 235 mm Quill taper: MT 5 Motor power: 7.5 kW (10.0 HP) Machine dimensions (W x D x H): 3,630 x 1,200 x 1,520 mm Weight: approx. 2,900 kg Features Versatile applications in general engineering, production, single-part manufacturing, etc. Central, easy-to-use control for feeds and threads using leadscrew and feed shaft Prism bed made of cast iron, induction-hardened and precision-ground Modern main spindle bearing with precision angular contact roller bearings Hardened and ground gears and shafts, including in the feed gearbox Rapid traverse for longitudinal and cross feeds as standard to reduce idle times Large spindle bore (105 mm) for workpieces with large diameters Smooth start via mechanical multi-disc clutch Electromechanical foot brake for reduced idle times Excellent cutting performance even for facing operations The machine bed is reinforced with sturdy ribs to increase rigidity and minimize vibration influences Scope of delivery 3-axis digital readout ES-12 V with LCD display Slip clutch Rapid traverse longitudinal and cross LED machine light 3-jaw steel chuck PO3-315 mm / D8 Faceplate 450 mm Fixed steady rest – max. dia. 180 mm Travelling steady rest – max. dia. 120 mm 2 centre points Motor with magnetic brake according to CE standards Foot pedal with brake function according to CE Initial fill with Shell Tellus 46 Coolant system Quick-change tool post with 4 holders Protection device for quick-change tool post Change gears Reducing sleeve Chip guard Cable routing via energy chain Operating tools

Leto izdelave: 2010, stanje: dober (rabljeno), 2 SICON shredders Year: 2010 Electrical cabinet is missing Price: €15,000 each Hjdpsiz Tm Iofx Af Ton 4 densimetric tables: €8,000 each

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Mettler Toledo metal detector Metal detector Brand: Mettler Toledo Aperture dimensions: 45 x 17 cm Hodpfx Afowmxl Se Tsn Overall dimensions: 120 x 240 x 130 cm

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, leto zadnje generalne obnove: 2025, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Hjdpovf E Avefx Af Tsn Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Leto izdelave: 2016, stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Znamka: Reifenhauser Model: Mirex-MT-V 1-RZE 120-1800 Leto: 2016 Stanje: Odlično Hedpfx Aevbcbuef Tjn Uporaba: PET / PP / PS folija ali plošča PET: Območje debelin: 0,25 – 2,2 mm Izhodna zmogljivost: 2.000 kg/h Največja širina plošče: 1.600 mm Ekstruder: RZE 120 mm Električna napajana: 3 x 480V 60Hz z N Širina kalandrske valjev: 1.800 mm Premeri kalandrske valjev: 450 / 700 / 700 mm Silikonska kopel, največja širina plošče: 1.600 mm Silikonska kopel, območje debelin plošče: 0,15 – 1,5 mm Vključen štiripozicijski navijalec WOB 1800 za navijanje dvojnega traku. Vse informacije so lahko predmet sprememb in/ali napak. Vsa oprema je na voljo do prodaje ali do umika iz prodaje.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: HBC 140 2x75kW 2001 (210-008-01), stiskalna sila: 155 t, teža bale: 1.500 kg, pritisk: 250 letvica, moč: 150 kW (203,94 KM), leto zadnje generalne obnove: 2024, Oprema: dokumentacija / priročnik, Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Kanaalbalenpers (2x75kW). Pers: Gewicht: 47.100 kg Hsdpfetvau Aex Af Ton Bouwjaar: 2001 Variabele kanaaldrukregeling Kunststof ventiel Anti-ratten bekabeling Draaiuren: 0 na volledige revisie Deze pers wordt volledig gereviseerd verkocht volgens de 'Bollegraaf OEM Certified Refurbishment standards', inclusief 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene principes van revisie Reiniging & demontage Voordat de feitelijke revisie plaatsvindt, wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Toleranties Na demontage worden de toleranties van alle stalen componenten gemeten en opnieuw gelast waar nodig. Dit geldt ten minste voor de volgende onderdelen: • Persplunjer, • Frame, • Perskanaal, • Voorpersklep Na demontage en inspectie wordt de persplunjer opnieuw opgelast en voorzien van nieuwe plunjerwielen. De beschermroosters en de voorpersklep worden deukvrij gemaakt en waar nodig gerepareerd. Opnieuw gespoten Na het meten van de toleranties en alle benodigde reparatie- en laswerkzaamheden, worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydrauliekleidingen en -slangen worden vervangen. De hydraulische componenten worden opnieuw verpakt. De hydrauliekolie wordt vervangen. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vervangen. Alle aansluitkasten worden vervangen en teruggeplaatst op goed toegankelijke plekken. Slijtdelen: Alle slijtdelen worden vervangen. De pennen en assen van de cilinders en het perskanaal worden vernieuwd. Alle slijtdelen van beide naaldinstallaties en knopers worden vervangen door nieuwe. Cilinders: De cilinders worden opnieuw verpakt en indien nodig voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC Kast De schakelkast wordt gecontroleerd en schoongemaakt. Indien nodig worden elektronische componenten vervangen door nieuwe. De PLC en HMI (mens-machine-interface) worden vervangen door de nieuwste Schneider M340-versie, inclusief de meest recente software.

Stanje: dober (rabljeno), Leto izdelave: 2011, Krauss Maffei Injection Moulding Machine KM 850-12000 MX With Krauss Maffei robot Year of manufacture: 2011 Hydraulic-mechanical two-platen clamping system with 4 pressure pads and 4 locking units on the moving platen. PV - injection unit stroke control. MC 5 control system with colour monitor, integrated control panel, and USB data carrier. Plasticizing unit Complete plasticizing unit for thermoplastics with screw diameter 135 mm, with non-return valve and open nozzle. Nozzle radius 25 mm, nozzle orifice 9 mm TECHNICAL DATA Clamping unit - Clamping force: 8500 kN - Opening force: 560 kN - Mounting platen dimensions (h x v): 1600 x 1600 mm - Tie bar clearance (h x v): 1140 x 1140 mm - Opening stroke: 1600 mm - Mould height (min-max): 500 - 1100 mm - Daylight: 2100 mm - Ejector stroke: 300 mm - Ejector force: 200 / 100 kN Injection unit - Screw diameter: 135 mm - Injection pressure: 1389 bar - Shot volume: 8588 cm³ - Shot weight for PS: 6098 g - Injection rate: 1414 cm³/s Electro-hydraulic equipment - Rated motor power (pump): 132 kW - Dry cycle time according to Euromap 6: 965 1/h - Oil tank capacity: 2440 l Hsdpjtrya Refx Af Tsn Weight and dimensions - Net weight with control cabinet: 49 t - Installation space (L x W x H): 11.72 x 2.92 x 2.71 m

Stanje: pripravljen za uporabo (rabljen), Number of knives: 6, rotor diameter: 350 mm, motor power: 50 kW, with design as reinforced steel/welded construction and documentation. Inspection is possible. Year of manufacture unknown, comprehensively overhauled in 2022. Hsdpfx Ajn Tpmuef Tjn