Edgebander

BIESSE AKRON 1400

Stanje: rabljeno, Leto izdelave: 2015, Funkcionalnost: popolnoma funkcionalen, BIESSE Edge Banding Machine AKRON 1440-A Automatic single-sided edge banders for bonding and processing flat edges using coil materials (melamine, PVC, ABS, veneer) and strip materials (solid wood, laminate, knife-cut veneers, etc.) • NC control with touchscreen • Automatic start of aggregate motors • Direct selection for second pass • Production data acquisition • Software-guided maintenance TECHNICAL DATA Workpiece thickness: 10–60 mm Workpiece thickness with MFU aggregate (profile-dependent): 10–35/60 mm Edge height: 14–64 mm Edge thickness (coil material): 0.4–3 mm Edge thickness (strip material *): 0.4–10 (12) mm Workpiece projection: 25 mm Minimum panel length: 140 mm Minimum width (at 140 mm length): 85 mm Minimum width (at 250 mm length): 50 mm Feed speed: 12 m/min Extraction*: 8x connection Ø100 mm Compressed air connection: 7 bar Glue pot capacity: 2 (approx.) kg *Depending on configuration. - GLUING UNIT VC-511 Applies hotmelt adhesive to the workpiece, feeds the edge material to the workpiece, automatically trims it from the coil, and presses it in place for optimal positioning. - TRIMMING UNIT IN-801 For trimming the front and rear edge overhangs at angles from 0° to 15°. - 2-MOTOR MULTIFUNCTION PROFILE MILLING UNIT AR02 E For corner rounding and profile milling of workpiece edges made of synthetic material up to a maximum thickness of 3 mm. JOINTING UNIT RT02 Joints the workpiece prior to glue application. Fitted with two 1.8 kW high-frequency motors at 12,000 rpm. SCRAPER UNIT RB02 For post-processing of thick PVC/ABS edges. FLAT SCRAPER UNIT RC02 For removing excess glue at the joint area between edge and panel. Equipped with tracing rollers and a straight knife with insertion control. BUFFING UNIT SZ02 For cleaning and buffing the workpiece edges with cloth polishing discs. The unit automatically adapts to workpiece thickness. ANTI-ADHESIVE SPRAY UNIT ADZ02 Precision application of release agent via injectors actuated by CNC control. KIT PRO-GLUE The PRO-GLUE kit consists of the following components: • TEKNO-GLUE system for optimum gluing, featuring: - controlled glue roller pressure - automatic retraction during feed stops - automatic ON/OFF of glue section REVERSE system for glue roller operation in forward or reverse mode. Bjdpfx Afexzb Iisnjld Electrical and mechanical provision for the use of special glue pots for POLYURETHANE adhesive on machines configured for EVA glue. NC Axis for Fine Trimming Unit Kit for automatic adjustment of tracing rollers and tools according to edge type or thickness, controlled via the CNC. Pair of multi-profile cutters for the fine trimming unit: Bevel cutter 25°, R=2 mm + R=1 mm, and straight profile for solid wood. NC Axis for Profile Milling Unit Kit for automatic adjustment of the sensor relative to edge thickness, controlled via the CNC. Allows activation of corner-only processing. NC Axis for Scraper Unit Kit for automatic adjustment of tracing rollers and tools according to edge type or thickness, controlled via the CNC.

Stanje: dober (rabljeno), Leto izdelave: 2007, številka stroja/vozila: 94323, potovalna razdalja osi X: 3.060 mm, pomik osi Y: 1.260 mm, pomik po osi Z: 150 mm, skupna višina: 2.400 mm, skupna dolžina: 4.400 mm, skupna širina: 2.800 mm, skupna masa: 3.130 kg, For sale: CNC MACHINING CENTER IN CONTINUOUS OPERATION Biesse ROVER 3.03 CNC machining center Fully operational, available for inspection in Wadowice X-axis travel: 3060 mm Blsdjwpthtspfx Afned Y-axis travel: 1260 mm Z-axis travel: 150 mm Control type: CNC XP 600

Stanje: delavnici obnovljeno (rabljeno), Priključna moč 380V 13A, pogonski motor 5,5kW + podajalni motor 0,7kW, širina skobljanja 630 mm, gred Tersa s 4 noži, brezstopenjski podajalni pomik 6-18 m/min, stikalo zvezda-trikot, mehanska nastavitev višine mize s pomočjo ročne ročice – pogon preko nožne gredi, fino nastavljanje z ročnim kolesom, mehanski digitalni prikaz višine oblanja, 1x mizni valj, priključek za odsesavanje 160 mm, 1x jekleni podajalni valj, 1x jekleni izstopni valj. Bsdpfexdl U Ejx Afnold

Stanje: rabljeno, Leto izdelave: 2018, Funkcionalnost: popolnoma funkcionalen, SCM Olimpic K 560 Automatski stroj za kantiranje, godina 2018 na prodaju! Kompletacija: - Lančani transport s brzinom 12/18 m/min - Debljina trake za kantiranje: 0,4–3 mm - EVA ljepilo - Jedinica za glodanje ploča "RT-V" - Jedinica za nanošenje ljepila „VC-S4.1“ - Jedinica za rezanje ruba "K-SEL" - Jedinica za glodanje ruba "R-K" - Jedinica za zaobljenje kutova "ROUND X" - Jedinica za struganje ruba RAS-K - Jedinica za poliranje SP-V Tehničke karakteristike: - Brzina transportera (dvije brzine) m/min: 12 - 18 - Minimalna/maksimalna debljina obratka mm: 8 - 60 - Debljina lijepljenog drvenog ruba mm: 0.4 - 6 (8 mm kod HP kompozicije) - Debljina lijepljenog rubnog traka mm: 0.4 - 3 - Maksimalna površina lijepljene trake mm²: 135 - Promjer nosača kalema („tanjur“) mm: 780 Bljdjw Sw Tkspfx Afnod - Maksimalno preklapanje lijepljenog ruba u odnosu na obradak mm: 2+2 - Minimalni razmak između transportiranih komada mm: 600 - Minimalna duljina obratka (pri minimalnoj širini od 100 mm) mm: 140 - Minimalna duljina trake mm: 180 - Minimalna duljina drvenog ruba mm: 220 - Minimalna širina obratka (pri minimalnoj duljini od 210 mm) mm: 95 (60 mm opc.) - Širina produžetka stola mm: 560 - Visina radne površine od poda mm: 900 Jedinica za glodanje ploča „RT-V“: - Maks. površina skidanja odvarka mm²: 55 - Maks. debljina glodanja mm: 3 - Minimalna/maksimalna debljina obratka mm: 8–45 (60 mm opc.) - Snaga motora kW: 2 x 1,5 - Promjer glodala mm: 100 - Visina glodala mm: 49 (64 mm opc.) - Brzina rotacije alata o/min: 9.000

Stanje: zelo dobro (rabljeno), Leto izdelave: 2018, Funkcionalnost: popolnoma funkcionalen, Smart Touch CNC control with Sintra HD software Panel height: 10 – 60 mm Solid wood: 22 mm PVC/ABS: 3 mm Feed speed up to 25 m/min Working height electronically adjustable via CNC Motorized panel support fence, electronically adjustable via CNC Anti-adhesive unit Pre-milling unit with 2 motors, electronically adjustable via CNC Coil holder plate with 1 position Bljdpfewlbxljx Afned Gluing unit for EVA hot-melt adhesive with glue pot End trimming unit with 2 motors, featuring a dynamic extraction system that follows the blades during all movements Flush and bevel trimming unit with 2 offset motors, electronically adjustable by CNC Anti-adhesive unit Corner rounding unit, multifunction with 2 motors (bevel trimming + corner rounding) Electronic edge scraper unit, electronically adjustable by CNC Glue scraper unit "SP-501" brush unit Automatic return system for workpieces with Winner 4A bridge offload

Stanje: zelo dobro (rabljeno), Leto izdelave: 1995, Max. panel width: 4400 mm Max. panel length: 4300 mm Max. main saw blade projection: 110 mm Bodpfx Afsmt Hhwoneld Number of clamps: 8

Stanje: rabljeno, številka stroja/vozila: 007913, Tip nameščenega roba: tanek rob, debel rob Bodpfx Aewkf Dvjfnold Lepilni sistem: EVA, vroč zrak Spojno rezkanje: da Multifunkcijska enota: da Maksimalna debelina plošče: 60 mm Delovni agregati: 7 št.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2019, Ta formatna žaga razreda SCM SI 400EP je bila proizvedena leta 2019. Ima največji premer žaginega lista 400 mm in širino reza ob vzdolžnem vodilu do 1500 mm. Formatna krožna žaga omogoča kotno rezanje do 3800 mm in je idealna za natančno razrezovanje lesenih plošč. Za več informacij nas kontaktirajte. Bjdpfxsyabkvj Afnold • Stanje stroja: Zelo dobro • Največji premer žaginega lista (z nameščenim predrezilom): 400 mm • Največja višina žaginega lista nad mizo pri 90° / 45°: 140 / 97 mm • Širina reza ob vzdolžnem vodilu (kapaciteta vzdolžnega reza): 1000 - 1500 mm • Največji hod formatnega vozička: 3200 - 3800 × 3200 mm • Moč trifaznega motorja od: 7 kW (8 kW) / 50 Hz (60 Hz)

Stanje: dober (rabljeno), Leto izdelave: 2012, Funkcionalnost: popolnoma funkcionalen, CNC machining center with edge banding for shaped workpieces Working dimensions for Y1 axis: X-axis: 4,300 mm X-axis, pendulum operation: 1,620 mm Y-axis: 1,320 mm Working dimensions for Y2 axis (edge processing): X-axis: 3,300 mm X-axis, pendulum operation: 600 mm Y-axis: 1,240 mm Worktable: 8 ATS workpiece supports, each with 3 vacuum suction cups 8 rear workpiece stops, lowerable via program, integrated in each support 8 workpiece stops, 670 mm from the back, mounted in each support, 2 + 2 lateral workpiece stops 4 removable central stops 6 lifting rails, pneumatically lowerable via program, for positioning heavy workpieces Automatic positioning of workpiece supports and vacuum suction cups via EPS (Electronic Positioning System) Automatic central lubrication Vacuum system divided into 2 separate working zones in X direction Vacuum support system for clamping templates Chip conveyor integrated in the machine table Vacuum pump 90 cbm/h Processing head equipment: Mounted on Z2 axis Drilling head BH 26 2L with: 16 vertical drilling spindles, each individually selectable 2+2 horizontal drilling spindles in X direction 2+2 horizontal drilling spindles in Y direction Grooving saw, diameter 120 mm, fixed in X direction Grooving saw, diameter 120 mm, fixed in Y direction Milling spindle 13.2 kW (11 kW S1 operation), HSK 63 F Mounted on Z1 axis Rotational speed 1,000 – 24,000 rpm Clockwise/counterclockwise rotation C axis, 360° for adapter units Cleaning nozzle for cleaning the milled edge before the edge-banding process 16-position tool magazine Edge banding unit for workpieces up to 60 mm thickness Edge banding unit CNC-controlled, with endless 360° rotation Glue application for hot-melt adhesive Double pressure roller, changeable and switchable Heating lamp for preheating the edge material Bjdpfx Afsxraimonjld End trimming unit for cutting the edge material at an 8° angle to the workpiece edge using a circular saw blade Technical data: Plastic edge thickness 0.4 – 3 mm (*) Solid edge thickness 0.4 – 2 mm (*) (Best results obtained using primed wood edges 0.4 – 1.2 mm) Max. edge height 64 mm Panel thickness min. 14, max. 60 mm Min. internal radius 18 mm (for edge thickness less than 1 mm) Min. internal radius 30 mm (with edge thickness 2 mm) Min. panel size for edge banding: 300 x 300 mm Min. size for internal cutout banding: 350 mm, with plastic edge max. 1 mm thickness and max. panel thickness 18 mm Edge magazine for 2 rolls, positioned outside the machine—this solution limits pendulum processing. Roll diameter for edge material: 800 mm Safety features: * Safety mats in front of the machine * Safety fence on the right with access door Without tools Control system: PC control with BIESSE WORKS ADVANCED Restart after emergency stop BIESSE WORKS office version Aggregates: - Flush/radius milling unit - Combined profile/flat scraper aggregate - Saw unit

Stanje: rabljeno, Leto izdelave: 2014, Centre d’usinage CNC Biesse Skill 12 24 G FT Année de fabrication : 2014 Blsdpfxewnhanj Afnsd Numéro de machine : 60961 Porte-outil : HSK F63 10 têtes de perçage verticales 12 positions de changement d’outil Logiciel : BiesseWorks Axe X : 2465 mm Axe Y : 1260 mm Axe Z : 324 mm Démonté pour le transport sur une remorque standard ; 4500x2200x2400 mm ; poids net 2000 kg - Année de fabrication : 2014 - Documentation disponible : Oui - Certificat CE : Non - Système de serrage d’outil : HSK-F63 - Outil de perçage fourni : Oui └ Broches de perçage verticales [Nb] : 10 - Positions de changeur d’outil [Nb] : 12 - Zone de travail X [mm] : 2465 - Zone de travail Y [mm] : 1260 - Zone de travail axe Z [mm] : 324 Informations financières TVA : Le prix indiqué s’entend TVA en sus TVA/Régime de marge : TVA déductible pour les professionnels Livraison et reprise possibles à tout moment pour tout équipement industriel Glenn Smeets