Sidel SBO 6/10 stroj za raztezno pihanje

SIDEL SBO 6/10

Sidel stretch blow molding machine
Max. output: 6,000 bottles/hour
Max. bottle size: 3,000 cc
Lredpfsg Ailcjx Akheu
Blow stations: 6

The machine is in very good and well-maintained condition.

GENERAL INFORMATION
The SBO 6/10 features 6 cavities and 10 heating modules.
Operates with a variety of bottle sizes and designs from 0.25 to 3 liters.
Two-stage PET stretch blow molding machines from Sidel require pre-manufactured preforms to be fed into the machine. Separating the processes for producing bottles and preforms allows for production optimization, greater operational flexibility, and provides a higher production capacity and yield.

MAXIMUM PREFORM DIMENSIONS
Neck height: 9 – 41 mm (measured from bottom of support ring)
Minimum ID of neck: 19 mm
Maximum OD of neck: 34 mm
Preform support ring diameter: 29 – 51 mm
Maximum preform length: 210 mm

MAXIMUM BOTTLE DIMENSIONS
Maximum bottle diameter: 130 mm
Maximum bottle height: 380 mm
Bottle capacity: 0.25 – 3 liters

TYPICAL PREFORM WEIGHTS (for still and carbonated liquids)
0.25 liter bottle: 14-20 grams
0.50 liter bottle: 20-33 grams
1.00 liter bottle: 26-40 grams
1.50 liter bottle: 35-51 grams
2.00 liter bottle: 44-58 grams
3.00 liter bottle: 68-84 grams

BLOW WHEEL
Height: 3.5 meters
Number of cavities: 6
Clamping force: 10 tons
Item height (below neck) at discharge: approx. 1.4 meters
Machine DC drive motor power: 4 kW

HEATING UNIT
Height: 2 meters
Number of oven heaters: 10
Number of heating zones per module: 8
Maximum power: 170 kW

ELECTRICAL REQUIREMENTS
Maximum supplied power: 200 kW
Average consumption: 100–150 kWh (varies with bottle produced)

COMPRESSED AIR
Available supply pressure: 7–35 bar
Operating pressure: 7 bar
Flow rate: 50–100 Nm3/h (varies with bottle produced)
Blow pressure – Standard base: up to 25 bar
Blow throughput – Standard base: 110–550 Nm3/h
Blow pressure – Petaloid base: up to 35 bar
Blow throughput – Petaloid base: 155–770 Nm3/h

CHILLED WATER
Temperature: 10–12°C
Pressure: 5–6 bar
Flow rate: up to 6 m3/h
Heat dissipation: up to 16,000 kcal/h

WEIGHT
Blow wheel with molds: 8 tons
Heating unit: 2.2 tons
Preform feeder: 0.65 tons
Control cabinet: 0.85 tons

PREFORM HEATING UNIT
The preforms are transported with the necks facing upward to the heating unit. This module ensures that preforms are rotated before passing neck-down in front of the heating elements, and again afterward. During the heating phase, the preforms are rotated and the necks are shielded from heat to optimize thermal distribution without distorting the neck. Heating is performed via 10 heating modules. Each module can accommodate up to 8 horizontally-stacked IR lamps, with air-cooled ends. The heating output of the 8 zones—matching the 8 lamp rows—is adjustable to optimize the temperature profile. These zones are regulated across all SBO models. After heating, an IR camera monitors preform temperature, enabling automatic adjustment of the controlled zones to maintain the required temperature at all times.

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.