Brusilnik s širokim trakom

SCM dmc sd 60

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2018, Glavni pogon Moč motorja vretena: 11 kW Tračna brusilka SCM DMC sd60 je bila izdelana leta 2018. Pokriva delovno širino 1.100 mm ter obdeluje materiale višine od 4 do 170 mm. Opremljena je z glavnim motorjem 15 kW ter omogoča podajalne hitrosti 4,5/9 m/min. Dodatne funkcije vključujejo kalibracijski valj, obložen z gumo, brusilni valj, trdo brusilno nogo in elektronske kontrole za natančno delo. Razmislite o nakupu te tračne brusilke SCM DMC sd60. Za več informacij nas kontaktirajte. Isdpjw R E Imefx Agpsa Vrste uporabe Brušenje

Stanje: kot nova (razstavni stroj), Leto izdelave: 2021, Funkcionalnost: popolnoma funkcionalen, širina brušenja: 1.350 mm, SCM Wide-Belt Calibration and Fine Finishing Sander Model: dmc sd 60 RCS 135 Technical Data: Working width: 1,350 mm Min./max. working height: 4–170 mm Abrasive belt width: 1,370 mm Abrasive belt length: 2,150 mm Main motor power: 11 (15) kW (HP) Feed motor: 0.45/0.8 (0.6/1.1) kW (HP) Feed speed: 4.5/9 m/min Standard Equipment: - R140/85 rubber-coated calibrating roller, 140 mm diameter, 85 Shore hardness – 1st position - R160/45 rubber-coated sanding roller, 160 mm diameter, 45 Shore hardness – 2nd position - Hard sanding pad with manual adjustment of working height - Motor power for 1st unit: 11 kW (15 HP) Ijdpfx Agetwqn Sjpoa - Electronic ammeter for main motor, indicates power consumption - Electronic digital display for working height - Electronically controlled abrasive belt oscillation - Rubber pressure rollers - Anti-kickback device at infeed before the first unit - Rubber feed belt, 60 Shore hardness - Roller table with two rollers at infeed and outfeed of the working table - Conveyor feed with two speeds: 4.5 / 9 m/min, via geared motor - Automatic conveyor belt tracking Including the following special equipment: 1 pc. Version "B" for RCS with: pneumatic on/off switching of roller for 1st unit “R” + pneumatic on/off switching of roller for 2nd unit “CS” + “MESAR” elastic segmented pad + pneumatic on/off for sanding pad unit + electronic programming unit “LOGIC 50” + electronic adjustment of working height 1 pc. CE safety compliance 1 pc. roller table at infeed and outfeed for long workpieces, equipped with 5 non-driven rollers 1 pc. "RA" diagonally grooved steel contact roller for 1st unit 1 pc. main motor 18.5 kW (25 HP)

Stanje: novo, - NEW - GENERAL FEATURES: Machine Frame and Work Table * Steel structure with electrical control cabinet located at the front of the machine * Sanding belts inserted from the left side of the machine * Motorized table height adjustment * Main motor integrated into the machine frame Electrical Equipment * Electromechanical control panel on the left front side of the machine * Automatic star-delta starter for the main motor * Motor protection switches for the motors * Motors with insulation class IP 54 Emergency and Safety Devices * Safety microswitch for thickness limit exceedance * Automatic brake for immediate stop of the aggregates * Emergency stop bar at the workpiece infeed * Mushroom emergency stop buttons at workpiece infeed and outfeed * Lockable main switch * Automatic emergency shutdown of the machine in case of: - Sanding belt breakage - Unsufficiently tensioned sanding belt - Lateral deviation of the sanding belt - Lack of compressed air - Main motor overload Note: The standard version with 400 Volt 50 Hz requires a three-phase mains supply + neutral wire + earth wire. If the 400 Volt power supply has no neutral wire, a single-phase transformer from the price list must be ordered. The same transformer must also be ordered for machines with voltage higher than 400 Volts, regardless of whether a neutral wire is present. The version of the machine with 220 or 230 Volts (50 or 60 Hz) is available at a surcharge (see price list). STANDARD BASIC MACHINE EQUIPMENT - R140/85 rubber-coated calibration roller, diameter 140 mm, 85 Sh - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm, 45 Sh - 2nd position - Hard sanding pad with manual working height adjustment - Main motor 11 kW (15 HP) - Electronic ammeter for the main motor to display current consumption - Electronic display for working height - Electronically controlled sanding belt oscillation - Rubber pressure rollers - Kickback protection at infeed before the first aggregate - Rubber feed belt 60 Sh - Roller table with two rollers at infeed and outfeed of the work table - Feed belt with two speeds 4.5 / 9 m/min with geared motor - Automatic belt centering Working width mm 1,100 Min./Max. working height mm 4 - 170 Sanding belt width mm 1,115 Sanding belt length mm 2,150 Main motor output kW (HP) 11 (15) Isdpovwfrnsfx Agpea Geared motor kW (HP) 0.45/0.8 (0.6/1.1) Feed speed m/min 4.5/9 Consisting of: 10.90.87 European safety standards (C.E. mark) 93.07.31 Volt 400 EU 93.12.01 Frequency 50 Hz 44.44.19 Version "B" for RCS 33.31.50 Roller table at infeed and outfeed for long workpieces 62.44.50 10-inch control panel with "eye-S" software integration 31.21.60 "RA" helical-grooved steel contact roller - 1st aggregate 97.50.71 Main motor 15 kW (20 HP)