Karbida konec mlin

Prototyp 10 x 22 /R 2

Stanje: zelo dobro (rabljeno), Leto izdelave: 2013, Nosilnost: največ 1.500 kg Območje debeline žice: 0,5 - 8,0 mm Zunanji premer tuljave: največ 1.000 mm Notranji premer tuljave: najmanj 300 mm Število obratov: 0 - 80 obr/min Fedpfx Asvam Iijpljpg

Leto izdelave: 1991, stanje: pripravljen za uporabo (rabljen), Axes: 5, max. grinding wheel diameter: 150 mm, spindle speed: 9,000 rpm, workpiece spindle speed: 1,500 rpm, clamping spindle speed: 13,000 rpm, travel X/Y/Z: 200 mm / 190 mm / 150 mm, tool holder: HSK-50. Machine dimensions X/Y/Z: approx. 1,700 mm / 1,400 mm / 1,800 mm. Control: NumRoto 1060. Control unit is defective. Includes coolant pump and coolant tank, set of grinding wheels with 12 holders. Documentation available. On-site inspection possible. Fpsdpfx Aevu Dfbeplsg

Stanje: zelo dobro (rabljeno), Leto izdelave: 2008, Funkcionalnost: popolnoma funkcionalen, vrsta vhodnega toka: Klimatska naprava, hladilna zmogljivost: 56 kW (76,14 KM), vrsta hlajenja: voda, vhodna frekvenca: 50 Hz, ogrevalna zmogljivost: 67 kW (91,09 KM), vrsta goriva: plin, "SANYO" PANASONIC ECO G Gas Heat Pump Air Conditioner Model: SGP-E190J2GU2W Nissan FY5 engine Power supply: 230 V AC, 1 phase, 50 Hz Max. electrical power input: 1.16 kW, 5.4 A (continuous operation) Device protection rating: IP24 Cooling capacity: 56 kW Heating capacity: 67 kW Thermal input (GCV) (cooling): 43.5 kW Thermal input (GCV) (heating): 46 kW Fedpfx Aod Tiu Eoplopg Refrigerant: R407C, 17 kg Design pressure high-side: 30 bar Design pressure low-side: 16 bar FOR OUTDOOR USE ONLY! We have 4 units in stock!

Stanje: rabljeno, Leto izdelave: 1997, - Edge banding unit Fjdpfx Apod Inktelspg - Cross-cutting unit - Milling unit - Fine milling unit - Scraper - Buffing unit

Stanje: rabljeno, številka stroja/vozila: 7979, Table diameter: 400 mm Table with 8 T-slots: 12 mm Fedpfxjb Ez R Ue Aplepg Overall height: 175 mm Required space: 600 x 450 x 175 mm Weight: approx. 100 kg

Stanje: zelo dobro (rabljeno), Leto izdelave: 2013, Traub TNL 18-7B CNC Automatic Lathe Base Machine: 2441 x 1396 mm Weight: 3800 kg Spindle Height Above Floor: 3800 mm Connected Load: 24 kW Main Spindle Max. Bar Capacity: 18 mm Max. Speed: 12,000 rpm Corner Speed: 5,000 rpm Z-axis Stroke: 205 mm Rapid Traverse: 40 m/min Measuring System Resolution Z: 0.001 mm Feed Force: 3000 N Spindle Nose / Short Taper: Traub short taper interface Max. Clamping Force: 1400 daN Max. Clamping Pressure: 40 bar Min. Clamping Pressure: 7.5 bar Piston Area: 40 cm² Total Cylinder Stroke: 5 mm Draw Tube Thread: M25 x 1 Counter Spindle Workpiece Diameter: 21 mm Clamping Depth Workpiece: 180 mm Max. Speed: 12,000 rpm Travel: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid Traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Max. Clamping Pressure: 30 bar Min. Clamping Pressure: 10 bar Upper Tool Turret with B-axis Number of Stations: 8 Shank Cross-section, Turning Tool: 16 x 16 mm Travel: X: 120 mm Y: -25/+40 mm Z: 250 mm Rapid Traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Tool Change Time: 0.5 sec Measuring System Resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Lower Tool Turret Fpsdpfx Apjwg Takeljg Number of Stations: 7 + counter spindle Shank Cross-section, Turning Tool: 16 x 16 mm Travel: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid Traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Tool Change Time: 0.5 sec Measuring System Resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Driven Tools for Upper Tool Turret Number of Driven Stations: Max. 8 Drive Power: 2 kW Max. Speed: 12,000 rpm Torque: 3.9 Nm Driven Tools for Lower Tool Turret Number of Driven Stations: 7 + counter spindle Drive Power: 3.4 kW Max. Speed: 12,000 rpm Torque: 7.3 Nm Driven Tools for Rear Unit Number of Stations: 7 Number of Drivable Stations: Max. 3 Station Pitch: 46 mm Drive Power: 2 kW Max. Speed: 7,500 rpm Torque: 4.7 Nm Drive Power: 2 kW Max. Speed: 4,000 rpm Torque: 11.8 Nm SCOPE OF SUPPLY Includes (not exhaustive): Traub CNC Lathe Tool holders, driven and non-driven High-pressure and belt filter system Oil mist separator Fire suppression system Chip conveyor Bar loader Operating documentation Exact scope of supply as per photo documentation No guarantee is given for the correctness, completeness or timeliness of the information provided.

Leto izdelave: 2013, stanje: pripravljen za uporabo (rabljen), Connected load: 4 kW, weight: 1 t. Fpjdshlp Efspfx Apljg

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2013, obratovalne ure: 5.446 h, največja hitrost vretena: 12.000 obr/min, potovalna razdalja osi X: 762 mm, pomik osi Y: 508 mm, pomik po osi Z: 508 mm, moč vretenovega motorja: 22.000 W, obremenitev mize: 300 kg, število mest v zalogovniku orodij: 41, število osi: 5, This 5-axis HAAS UMC 750 was manufactured in 2013. It offers a spindle speed of 12,000 rpm and a tool capacity of 41 tools, making it suitable for a variety of machining applications. The machine provides a maximum table load of 300 kg and is equipped with advanced coolant systems for efficient operation. If you are looking for high-quality machining capabilities, consider the HAAS UMC 750 universal machining center we have for sale. Contact us for further details. • Spindle type: Inline direct drive • Tool holder: SK40 • Tool changer: SMTC • Rotary axes: 2 axes with support bearings • B-axis travel range: -35° to +110° • C-axis travel range: 360° Fedpfjyid Hvex Aplspg • Clamping surface: Ø 630 × 500 mm • Coolant system: Standard coolant, P-Cool, through-spindle coolant (TSC) • Renishaw probe: WIPS system with workpiece and tool measurement • Control functions: 8M functions, rotation and scaling • Memory: 16 MB • HSM: High-speed milling • Rigid tapping: yes • Cycle time hours: 5,446 h • Power-on hours: 21,246 h Technical Specification Taper Size SK 40

Stanje: rabljeno, Leto izdelave: 1998, Premer struženja nad ležiščem: 0400 mm Premer struženja nad suportom: 260 mm Dolžina struženja: 1500 mm Fpjdexp Rzbepfx Apleg Višina konic: 200 mm Razdalja med konicami: 1500 mm Vrtina vretena: 50,8 mm Obrati: 20–3150 min⁻¹ Pomiki vzdolžni suport: 0,01–3,24 mm/obrat Pomiki prečni suport: 0,005–1,62 mm/obrat Teža stroja pribl.: 2 t Prostorska zahteva pribl.: 3,35 x 1,4 x 1,9 m Obratovalna napetost: 400 V Priključna moč: 7,7 kVA Z vpenjalom, Multifixom in digitalnim prikazovalnikom.

Leto izdelave: 1988, stanje: rabljeno, številka stroja/vozila: 103.071.3156.78192, Saw blade diameter: 400 and 425 mm Cutting capacity at 90° round: 130 mm Cutting capacity at 90° square: 120 x 120 mm Mitre cutting capacity at 45° round: 130 mm Mitre cutting capacity at 45° square: 110 x 110 mm Cutting speeds: 11 and 22 m/min Feed rates: 670 mm/min Cut-off length: with automatic feed up to 1200 mm Electrical connection: 380 V, approx. 4 kVA Saw drive: 1.6/2.5 kW Space requirement: 1800 x 3800 x 2000 mm Fpsdez N Amopfx Aplsg Weight: approx. 1800 kg