Razdelilnik kolutov Rezalnik kolutov Giljotina

Klanke RGS20

Stanje: novo, - Motor power: 7.5 kW - Cutting force: 20 tons Cutting channel designed for: - maximum roll length: 1100 mm - maximum roll diameter: 900 mm - Machine weight: approx. 2500 kg - Tank capacity: approx. 100 litres - Safety guard in the operating panel area and on the opposite side - Colour scheme: machine body in RAL as per customer's request Bsdpfx Akjftnt Nsrjdc Safety guard/cutter bar in RAL 1028 melon yellow Custom order item Price and further information upon request

Stanje: dober (rabljeno), Leto izdelave: 2004, Funkcionalnost: popolnoma funkcionalen, Proizvajalec: HABERMEHL Anlagenbau GmbH Naslov: Hauptstr.1, 35510 Butzbach-Ebersgöns, Nemčija Tip: EH 400/1 Serijska številka: 901 Letnik: 2004 Napetost / frekvenca: 400 V / 50 Hz Nazivna moč: 3 kW CE-certifikat: Da 🛠️ Opis naprave Industrijski drobilnik oz. granulator (shredder/granulator). Bdsdpfxow Niuhe Akrsc Značilne lastnosti na fotografijah: Sistem z rotacijskimi noži (drobilna enota) na 2-mm gredi 3 kW SEW motor z reduktorjem 8 mm sito (na situ označeno: „8 mm Sieb“) – določa velikost izhodnih delcev Premična, transportna konstrukcija Posoda za izpust materiala in spodnja motorizacija Takšni stroji se običajno uporabljajo za drobljenje naslednjih materialov: Plastika Guma Les Lahki kovinski ostružki Elektronski odpadki 📝 Tehnične informacije, ki jih lahko zahtevate Za dodatne informacije se lahko pri dobavitelju ali proizvajalcu pozanimate za naslednje podrobnosti:

Stanje: novo, Leto izdelave: 2024, Hacker knives 40 x 40 concave Blades for Weima, Gross, etc. For almost all common chippers/shredders Available from stock in Bitburg Subject to prior sale Bdjdpfx Akjbxu Dhsrec

Stanje: novo, Leto izdelave: 2026, Consisting of bale breaker for large bales type MHB and straw shredder type MHZ 1) Bale Breaker MHB: Special price from €22,975 net (approx. 15 weeks production time) Suitable for round or square bales. Includes frequency converter (FU) – this controls the speed of the scraper floor. The bales are placed on the scraper floor and the feed of the milling unit is activated. The tines of the milling unit tear the straw from the bale and throw it into the hopper. Ideally, the combination of the bale breaker and straw shredder is recommended here. Technical data of the bale breaker: Capacity: 1–2 bales per hour, up to a maximum of 600 kg per hour (depending on the sieve size used in the straw mill and the kW rating of the straw mill). Without the straw mill, the bale breaker can process up to 900 kg/h of straw. Max. size of square bales: 2400 x 1200 x 800 mm (L x W x H) Milling unit motor: 5.5 kW, 380 Volt Scraper floor feed: 0.75 kW, 380 Volt Dimensions: 3750 x 1730 x 2460 mm (L x W x H) Weight: 400 kg 2) Straw Shredder MHZ 600 – 11/15 kW; available immediately Special price from €6,995 net Surcharge for the even larger straw shredder (18.5 kW): +€2,750 net Technical data, MHZ with special hopper: 15 kW 380 Volt electric motor Diameter: 600 mm Hardened cutting blades Screen with interchangeable inserts, optional perforations: (10, 12, 15), 22, 30, 45 mm With star-delta switch, overload protection, and 8 m connection cable ready to plug in Discharge nozzle: 160 mm Blowing distance: approx. 12 m Dimensions: approx. 1600 x 1020 x 1360 mm (L x W x H) Weight: approx. 240 kg --- Optional extras at a surcharge: Feed screw: +€970 net Cyclone (suspension to be installed by customer) *Should be installed no more than 10 m away +€2,970 net Simple filter: €1,750 net --- Further options: Industrial extraction system (demonstration unit) + from €9,950 net Optional with rotary valve (makes the material pressureless): +€5,750 net Control system: from €1,620 net Special extension for the bale breaker 3 m (other sizes on request) +€9,750 net Briquetting press MPP 180 S; lightly used demonstration unit 70 mm briquettes – up to a maximum of 100 kg/h from €39,700 net * Larger machines available on request Bsdpsb Nulhsfx Akredc --- Description: The muetek bale breaker was developed for breaking up round and square bales of hay and straw. The attached shredder attached to the bale breaker shreds straw from all cereal varieties, hay, maize, and miscanthus. The muetek machines of the MHZ/MHB series stand out due to their robust design and heavy-duty construction. muetek MHB series bale breakers are equipped with a chain conveyor on which the straw bale is placed using a front loader. The platform is adjustable depending on the bale type. The chain conveyor pushes the bale against the milling rotor, and the feed speed is adjustable. The milling rotor is equipped with multiple teeth that tear apart the straw bale. The straw separated from the bale is expelled. --- Basically, the machines are suitable for dry feedstocks: – Straw – Hay --- Processing hemp is only possible with a special bale breaker Surcharge approx. €9,720 net * depending on version. Shredding hemp is not possible with the straw mill. Requirements for the feed material: Moisture content max. 12%

Stanje: novo, Leto izdelave: 2025, Nova brusilna stroj za nože z vrtljivim magnetnim mizo, 1200 mm, hitrost sani brezstopenjsko nastavljiva, avtomatski pomik brusilnega koluta, PLC krmiljenje, barvni zaslonski zaslon na dotik, hladilni sistem. Bdedpewamkvsfx Akrjc

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, leto zadnje generalne obnove: 2025, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Bjdpfxjvf E Avs Akrodc Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Stanje: pripravljen za uporabo (rabljen), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for the economical volume reduction of recyclable residual materials in industrial and craft settings: - Cardboard boxes - Foam - PET bottles - Insulation mats - and other baled materials. Horizontal baler, waste press DIXI 60 SLD with tipper Technical specifications: - Pressing force: 60 tons - Specific pressure: 6.81 kg/cm² - Power supply: 400V / 7.5kW - Bale dimensions: 800x1100x1200 mm - Number of bindings: 3 - Bale weight: approx. 370-410 kg - Binding: manual - Loading aperture: 990 x 1110 mm Bdodpera A E Uefx Akrjc - Machine weight: 5,420 kg - Average pressing cycle: 47 sec - Year of manufacture: 2011-2016 Dixi 80SLD baler Technical data of the baler: Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Filling opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 s Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: Depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: - Length: 4,200 mm (+ cage 1,600 mm) - Width: 1,830 mm - Height: 2,620 mm - Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction ensures long-term operation Year of manufacture: 2016-2020 Weight: approx. 8.4 tons Condition: Used

Stanje: novo, Leto izdelave: 2025, Moč motorja 7,5 kW - Rezilna sila 30 ton Rezilni kanal zasnovan za - največjo dolžino koluta 1500 mm - največji premer koluta 850 mm - Teža stroja pribl. 3500 kg - Prostornina rezervoarja pribl. 110 litrov Bdsdpfx Aksgl Adzoroc - Zaščitna rešetka na območju upravljalne plošče in nasproti - Zaklep rezila - Razdelilna miza ravna izvedba - Dokumentacija v 2 izvodih v nemščini (1x v tiskani obliki, 1x CD) - Barva RAL 5012 svetlo modra Zaščitna rešetka/rezilni nosilec RAL 1028 melonsko rumena Stroj na zalogi in takoj dobavljiv Cena in dodatne informacije na zahtevo

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: HBC 140 2x75kW 2001 (210-008-01), stiskalna sila: 155 t, teža bale: 1.500 kg, pritisk: 250 letvica, moč: 150 kW (203,94 KM), leto zadnje generalne obnove: 2024, Oprema: dokumentacija / priročnik, Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Kanaalbalenpers (2x75kW). Pers: Gewicht: 47.100 kg Bouwjaar: 2001 Variabele kanaaldrukregeling Kunststof ventiel Anti-ratten bekabeling Draaiuren: 0 na volledige revisie Deze pers wordt volledig gereviseerd verkocht volgens de 'Bollegraaf OEM Certified Refurbishment standards', inclusief 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene principes van revisie Reiniging & demontage Voordat de feitelijke revisie plaatsvindt, wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Toleranties Bjdpfx Akotvau Aerjdc Na demontage worden de toleranties van alle stalen componenten gemeten en opnieuw gelast waar nodig. Dit geldt ten minste voor de volgende onderdelen: • Persplunjer, • Frame, • Perskanaal, • Voorpersklep Na demontage en inspectie wordt de persplunjer opnieuw opgelast en voorzien van nieuwe plunjerwielen. De beschermroosters en de voorpersklep worden deukvrij gemaakt en waar nodig gerepareerd. Opnieuw gespoten Na het meten van de toleranties en alle benodigde reparatie- en laswerkzaamheden, worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydrauliekleidingen en -slangen worden vervangen. De hydraulische componenten worden opnieuw verpakt. De hydrauliekolie wordt vervangen. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vervangen. Alle aansluitkasten worden vervangen en teruggeplaatst op goed toegankelijke plekken. Slijtdelen: Alle slijtdelen worden vervangen. De pennen en assen van de cilinders en het perskanaal worden vernieuwd. Alle slijtdelen van beide naaldinstallaties en knopers worden vervangen door nieuwe. Cilinders: De cilinders worden opnieuw verpakt en indien nodig voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC Kast De schakelkast wordt gecontroleerd en schoongemaakt. Indien nodig worden elektronische componenten vervangen door nieuwe. De PLC en HMI (mens-machine-interface) worden vervangen door de nieuwste Schneider M340-versie, inclusief de meest recente software.

Stanje: novo, Klanke roll splitter for efficient processing of reject rolls. Bdjdpfx Aon Hyxljkrec Features: - Automatic safety interlock - Knife guard - Emergency stop pull cord - Siemens PLC Technical specifications: Knife length: 1500 mm Cutting channel opening: 1200 mm Motor power: 7.5 kW Cutting force: 30 t Made to order Price and further information on request. We will gladly provide you with a non-binding offer.