Hidravlične enostebrne stiskalnice

KK Kletzer PCR 150

Leto izdelave: 1965, stanje: rabljeno, Pressure: 150 t Outreach: 550 mm Stroke: 10 - 140 mm Table surface: 1180 x 980 mm Strokes per minute: 40 Installation height: 500 mm Ram surface: 1040 x 800 mm Ram adjustment: 70 - 150 mm Pin hole (depth x diameter): 435 x 55 mm Power requirement: 15 kW Machine weight: approx. 12 t Ijdpocubatofx Abxsth Space requirements: approx. 3 x 1.7 x 3 m - with additional brake - ram weight compensation - motorised ram adjustment - central grease lubrication (manual) - break plate - table clamping plate - safe for manual feeding operations - operating manual available

Stanje: rabljeno, Technical Details: Pressing force: 100 t Installation height: Table/Ram top position: 800 mm Throat depth: 360 mm Ram stroke: 500 mm Ram advance speed: 200 mm/s Ram return speed: 200 mm/s Table size: 750 x 560 x 90 mm Passage in table: Ø 26 mm Ram mounting surface (W x D): 530 x 400 mm Pin hole in ram: Ø 50 mm Iedovc Ax Nepfx Abxsth Cylinder diameter: Ø 250 mm Height above floor: 720 mm Total power requirement: 17.0 kW Approx. machine weight: 5.5 t Approx. machine dimensions (L x W x H): 1.8 x 1.2 x 3.2 m

Stanje: rabljeno, Leto izdelave: 2007, Pressure: 200 t Throat depth: 510 mm Stroke: 16 - 160 mm Ram adjustment: 120 mm Table surface: 1500 x 1000 mm Table height above floor: 900 mm Clear opening in table: 800 x 250 mm Ram surface: 1000 x 700 mm Ram bore: 65 x 110 mm T-slot width: 28 mm Adjustable stroke rate: 30 - 120 strokes/min Hydraulic unit oil capacity: 5 l Die height (max. stroke, ram adj. up): 600 mm Die height (stroke down, ram adj. up): 440 mm Total power requirement: 32.2 kW Machine weight approx.: 24 t Space requirement approx. (WxDxH): 2.85 x 3.1 x 3.65 m - Hydraulic clutch - Fixed table - Hydraulic overload protection in ram - Hydraulic connecting rod clamping - Motorized ram height adjustment 120 mm with digital readout, rapid/creep mode - Fully automatic stroke adjustment, range 16 - 160 mm - Ram weight compensation - Electronic TDC correction - Planetary gearbox - Centralized circulating oil lubrication - Separate control console with screen control SIMATIC S7/300 - Press force measuring device - Reversing circuit (return stroke) - Additional operating mode "setup/creep mode" - Electric stroke counter - Electric preset counter Itjdpfevbk Rwjx Abxoh - Electric travel limitation of connecting rod pin - Electronic cam controller - Infinitely variable drive (frequency-controlled) - 2 sockets - Clamping plate - Temperature monitoring for main / support / connecting rod bearings - Operating hours counter - Oil cooler - Set of anti-vibration elements Additional equipment: Electronic roller feed ebu EVX 500 Passage width: 10 - 500 mm Material cross section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of rollers: 2 Roller diameter: 100 mm Intermittent ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Stanje: novo, Load capacity 500 kg. Number of suction cups: 6 units Diameter of suction cups: 215 mm Suction capacity: 8.0 m³/h Crane eye diameter: 80.0 mm Voltage: 400 V Total power requirement: 0.18 kW Machine weight: approx. 120 kg Space requirements: approx. 2400 x 1100 x 584 mm Equipment: - For horizontal transport of smooth, dry, and airtight panels - Robust steel load-bearing frame - Painted in RAL 2000, featuring a low dead weight - Galvanized longitudinal beam, length 2,400 mm - 3x galvanized crossbeams, each 1,000 mm long - 6x spring-loaded, articulated, and adjustable suction cup holders - 6x suction pads Ø 215 mm - Low-maintenance, high-quality, dry-running rotary vane vacuum pump - With a suction capacity of 8 m³/h and a final vacuum of 85% (150 mbar) - 3-phase 230/400 V + PE, 50 Hz, with cable (approx. 0.5 m long) - Telescopic operating handle, extendable up to 1,000 mm from beam center - Sturdy sheet metal holder for your crane control - "Suction / Release" operation via manual slide valve - Control and safety device for vacuum lifter * Robust control cabinet * Contactor control circuit for the vacuum pump * Safety warning system with acoustic sounder * Vacuum gauge with danger zone indicator * Large vacuum reservoir with safety check valve * Two-step operation for load release - Fine dust filter for vacuum pump protection - Documentation Ijdpjxak Ddsfx Abxeth * Special accessories included: - 6x ball valves for isolating individual suction cups * Enables handling of smaller formats without the need to move suction cups or crossbeams - Small spiral connection cable * Extension length up to 3,500 mm, designed as * Extension cable with CEE plug and coupling * Routed alongside the load chain to the lifting device

Leto izdelave: 1987, stanje: rabljeno, Pressure: 150 t Throat depth: 350 mm Stroke: 20–120 mm Strokes per minute: 50 / 75 spm Ram adjustment: 85 mm Table size: 1150 x 670 mm Ram surface: 800 x 380 mm Through-hole in table: 330 x 200 mm Table height: 800 mm Pin bore in ram: Ø 50 mm Machine weight: approx. 8 t Space requirement (WxDxH): approx. 2000 x 2000 x 2700 mm Features: - Hydraulic clutch-brake combination - Centralized oil lubrication - Mechanical overload protection in ram - Semi-automatic stroke adjustment - Manual ram adjustment - Two-hand control - Foot pedal operation Iedjp Apxhepfx Abxjth - Counter bearing

Stanje: rabljeno, Leto izdelave: 2016, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 103979, We offer for sale a used CNC vertical lathe EMAG, model VL5i F., year of manufacture 2016. The machine is in good condition and fully operational. It is currently still in production and can be inspected under power. Price: EXW, including loading. Iedpfx Abjuyh Tdsxsth For more information, please contact us.

Stanje: zelo dobro (rabljeno), Pressure 125 t Throat depth 400 mm Stroke 6 - 125 mm Itedpfxjt Eix Rj Abxoh Ram adjustment 100 mm Installation height (stroke bottom, ram adjustment top) 400 mm Table area 1100 x 750 mm Strokes per minute 60 spm Total power requirement 16 kW Machine weight approx. 10 t Required space approx. WxDxH 1.1 x 1.9 x 3.53 m - Machine partially overhauled - Completely disassembled and technically inspected, - New seals - New pneumatic clutch - New seals in the compensating cylinder - New drive motor - New ball screw - New paint finish - Current UVV inspection and brake time measurement Machine safe for manual loading operations At extra cost, we can equip the machine as follows: - Workspace protection with light curtain / cycle operation, but only in combination with a new control cabinet (freestanding) with ABB safety controller and touch panel - Two-hand operation on a separate stand

Leto izdelave: 1970, stanje: rabljeno, Pressure 100 t Throat depth 415 mm Stroke 8-140 mm Strokes per minute 48 spm Ram adjustment 80 mm Table area 920x670 mm Ram area 700x450 mm Table height 800 mm Ram bore Ø 50 mm Machine weight approx. 8 t Space requirements approx. WxDxH 1500x2000x2800 mm Mechanical overload protection Equilibration cylinder Manual stroke adjustment Manual ram adjustment Iodpfxolp U Spj Abxsth

Stanje: generalkompletno obnovljen (rabljeno), RETROFIT Complete Pressing force: 1600 kN Installation height: 800 mm Stroke: 500 mm Table: 900 x 630 mm Ram: 750 x 450 mm Throat depth: 360 mm Downward speed: 200 mm Upward speed: 125 mm Machine height: approx. 3,500 mm Weight: approx. 7,000 kg Connection: 17 kW Ijdsw S Uazspfx Abxoth - A complete retrofit kit for unrestricted manual loading and unloading in accordance with EU Conformity and implementation of equipment in line with CE regulations,  New control cabinet with certified dual-channel electronic PLC safety control system from Siemens (1512SP F or 1515F) for process control, featuring an integrated operator panel for the following operating modes: setup with two-hand operation, single stroke with two-hand operation, and foot control (only in combination with BWS); manual lever operation is no longer possible,  Hydraulic safety block for monitoring the closing movement on the main cylinder,  Position-monitored directional control valve for upward and downward movement of the main cylinder ram,  Two-hand control unit with dual-channel monitoring of the two-hand synchronization at the press table (incl. 5m cable),  Replacement of the main and control pump motors,  Replacement of the main cylinder seals,  Fine filter with contamination indicator,  The press features an electronic stroke measurement system (including teach-in function and current ram position display). This eliminates the need for a mechanical cam switch assembly. Main control panel integrated in the control cabinet (mounted on the right side of the machine) o 12" touch panel o Operating buttons and switches for modes and drives o USB interface for data exchange - Light curtain Option: Drawing cushion

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, delovna širina: 600 mm, vrsta vhodnega toka: trifazni, najv. debelina pločevine: 100 mm, najv. debelina jeklene pločevine: 100 mm, maks. debelina aluminijaste pločevine: 100 mm, najv. debelina bakrene pločevine: 100 mm, maks. debelina medeninaste pločevine: 100 mm, skupna dolžina: 1.500 mm, skupna širina: 1.100 mm, skupna višina: 1.700 mm, teža obdelovanca (maks.): 500 kg, skupna masa: 680 kg, delovna višina: 100 mm, vhodna napetost: 400 V, trajanje garancije: 12 meseci, dolžina mize: 1.300 mm, širina mize: 600 mm, višina obdelovanca (maks.): 100 mm, vhodna frekvenca: 50 Hz, širina obdelovanca (maks.): 600 mm, obratovalna hitrost: 33 mm/s, višina mize: 1.010 mm, premer brusilnega koluta: 150 mm, širina brušenja: 600 mm, vrsta nastavitve višine: mehanski, vhodni tok: 20 A, prehodna širina: 600 mm, Oprema: CE označba, Na voljo je tipska ploščica, dokumentacija / priročnik, Polnische Entgratmaschine – Direkt vom Hersteller Wir freuen uns, Ihnen unsere hochwertigen Entgratmaschinen vorstellen zu können, die in Polen von der Firma Madora Sp. z o.o. hergestellt werden – einem zuverlässigen und erfahrenen Unternehmen, das sich auf Metall- und Holzbearbeitungsmaschinen spezialisiert hat. Mit jahrzehntelanger Erfahrung und Innovationskraft ist Madora bekannt für langlebige, effiziente und bedienerfreundliche Lösungen, die auf die Bedürfnisse industrieller Kunden in ganz Europa zugeschnitten sind. Unsere Maschinen stehen für Präzision, Leistungsfähigkeit und langfristige Zuverlässigkeit – und das zu wettbewerbsfähigen Preisen. Das kleinste Modell der MADORA-Baureihe, die GP 600 2Z, ist eine vielseitig einsetzbare Entgratmaschine zur Reinigung von Blech nach verschiedenen Trennverfahren. Ausgestattet mit zwei Bearbeitungseinheiten vom Typ „Z“ besticht sie durch hervorragende Vielseitigkeit und Bearbeitungskapazität. Die Entgratmaschine führt zwei Arbeitsgänge gleichzeitig aus: Sie ermöglicht nicht nur das Entfernen von Zunder nach dem Plasmaschneiden, sondern auch das Entgraten oder Verrunden von Werkstückkanten nach dem Laserschneiden – alles in einem Durchlauf. Der Arbeitsbereich für Materialdicken und Breiten bis 600 mm ermöglicht das Bearbeiten von kleinen und mittelgroßen Werkstücken. Mit entsprechenden Werkzeugen eignet sich die Maschine auch für schweres Verrunden von Kanten und das Entfernen von Oxidschichten. Die GP 600 2Z ist mit einem elektrischen Bedienfeld mit Digitalanzeige ausgestattet, das es dem Bediener erlaubt, sämtliche Bearbeitungsparameter wie Werkstückhöhe, Vorschubgeschwindigkeit und Drehzahl der Werkzeuge vollständig und stufenlos zu steuern. Jede Bearbeitungseinheit kann unabhängig angesteuert werden, sodass der Bediener individuell festlegen kann, welche Arbeitsprozesse in einem Durchgang durchgeführt werden sollen. Itedpfjwzu A Nsx Abxsh