Avtomatski stroj za prebijanje - dvojni stolpec

Helmerding KDH 315/2100/2

Leto izdelave: 2008, stanje: rabljeno, Pressure: 315 t Stroke: 40–200 mm Stroke rate: 20–100 strokes/min Slide adjustment: 120 mm Slide area: 2000x1100 mm Bolster area: 2000x1200 mm Die opening in table: 1700x250 mm Shut height (bottom), slide adjustment top: 500 mm Side frame window: 820x650 mm Total power requirement: 45 kW Machine weight: approx. 44 t Hydraulic clutch-brake combination Hydraulic overload protection in slide Semi-automatic stroke adjustment Motorized slide adjustment Stroke rate frequency-controlled Central grease lubrication for guides Oil circulation lubrication Slide counterbalance cylinders Safety doors front/rear Hydraulic die clamping system Extendable bolster plate Hydraulic rollblock strips in table Codpfordi Dljx Agqogw Feed unit: Helmerding EWH800/150 (V-1341-6518) Strip width: 100–800 mm, strip thickness: 0.5–6.0 mm, max. strip cross-section: 1600 mm² Loop control, height adjustment via geared motor Straightener: R-70/800/9-S (R-1343-6518) Strip width: 100–800 mm, strip thickness: 0.5–4.0 mm, Max. strip cross-section: 1600 mm² at 450 N/mm² Straightening speed, frequency-controlled up to 25 m/min Strip introduction aid: transfer table with hydraulic separating wedge, hydraulically adjustable Hold-down hydraulically adjustable Strip edge guidance: 1 pair of lateral roller guides, adjustable via handwheel Feed rollers: 2x rollers Ø140 mm, pneumatically adjustable Straightener: 9x rollers Ø70 mm, adjustment manual via handwheel Decoiler: HE-4/800/MOT/HYD (H-1342-6518) Strip width: 100–800 mm Max. load: 4 t Coil inner diameter: Ø508 mm Coil outer diameter: Ø1000–1600 mm Drive, frequency-controlled Limiting arms Hydraulic expansion Hydraulic hold-down arm

Leto izdelave: 2016, stanje: pripravljen za uporabo (rabljen), The Coiltech Decoiler Straightener Feeder System is a compact coil feeding system for presses. Strip width: 600mm, material thickness: up to 6.5mm, straightening rollers: 7x115mm, decoiler capacity: 6000kg, inner diameter (min-max): 470-520mm. Connected load: 7.5kW, supplied with documentation. Cgodji El Ucspfx Agqow

Stanje: rabljeno, Leto izdelave: 2007, Pressure: 200 t Throat depth: 510 mm Stroke: 16 - 160 mm Ram adjustment: 120 mm Table surface: 1500 x 1000 mm Table height above floor: 900 mm Cedevbk Rwspfx Agqsgw Clear opening in table: 800 x 250 mm Ram surface: 1000 x 700 mm Ram bore: 65 x 110 mm T-slot width: 28 mm Adjustable stroke rate: 30 - 120 strokes/min Hydraulic unit oil capacity: 5 l Die height (max. stroke, ram adj. up): 600 mm Die height (stroke down, ram adj. up): 440 mm Total power requirement: 32.2 kW Machine weight approx.: 24 t Space requirement approx. (WxDxH): 2.85 x 3.1 x 3.65 m - Hydraulic clutch - Fixed table - Hydraulic overload protection in ram - Hydraulic connecting rod clamping - Motorized ram height adjustment 120 mm with digital readout, rapid/creep mode - Fully automatic stroke adjustment, range 16 - 160 mm - Ram weight compensation - Electronic TDC correction - Planetary gearbox - Centralized circulating oil lubrication - Separate control console with screen control SIMATIC S7/300 - Press force measuring device - Reversing circuit (return stroke) - Additional operating mode "setup/creep mode" - Electric stroke counter - Electric preset counter - Electric travel limitation of connecting rod pin - Electronic cam controller - Infinitely variable drive (frequency-controlled) - 2 sockets - Clamping plate - Temperature monitoring for main / support / connecting rod bearings - Operating hours counter - Oil cooler - Set of anti-vibration elements Additional equipment: Electronic roller feed ebu EVX 500 Passage width: 10 - 500 mm Material cross section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of rollers: 2 Roller diameter: 100 mm Intermittent ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Stanje: zelo dobro (rabljeno), Pressure 125 t Throat depth 400 mm Stroke 6 - 125 mm Ram adjustment 100 mm Installation height (stroke bottom, ram adjustment top) 400 mm Table area 1100 x 750 mm Strokes per minute 60 spm Total power requirement 16 kW Machine weight approx. 10 t Required space approx. WxDxH 1.1 x 1.9 x 3.53 m - Machine partially overhauled - Completely disassembled and technically inspected, - New seals - New pneumatic clutch - New seals in the compensating cylinder - New drive motor - New ball screw - New paint finish - Current UVV inspection and brake time measurement Codpfjt Eix Rjx Agqogw Machine safe for manual loading operations At extra cost, we can equip the machine as follows: - Workspace protection with light curtain / cycle operation, but only in combination with a new control cabinet (freestanding) with ABB safety controller and touch panel - Two-hand operation on a separate stand

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, Pressing force: 2,000 kN Table area: 2,300 x 1,100 mm (W x D) Die opening: 2 pcs. 700 x 300 mm Distance between uprights: 2,460 mm Ram clamping area: 2,300 x 1,100 mm Side passage: 740 mm Installation height: 550 mm (stroke bottom, adjustment top) Stroke rate: 30 - 140 strokes/min, steplessly adjustable Stroke: 20...220 mm Ram adjustment: 150 mm (motorized) Main drive: 30 kW Weight: approx. 27,500 kg Design features: • Control system Siemens + Beckhoff • 8-point sliding guide • Motorized oil circulation lubrication • Automatic ram adjustment • Hydraulic overload protection • Pneumatic ram counterbalance • Electromechanical stroke adjustment • Control system Siemens + Beckhoff • Beckhoff panel for visualization • T-slots in table and ram (28mm, 300mm spacing) • Vibration-damping machine feet • 4 pcs. tool clamps + 4 pcs. cam outputs • Ram with 20mm wide central groove • Hydraulic tool clamping device on table and ram • Hydraulic roll blocks for tool change Strip feeding line by Kemmerich, consisting of: Decoiler Type: V 5000 A – SH – 600 – S Load capacity: 5,000 kg Strip width: 100 - 600 mm Expanding range: 470 – 520 mm Coil outside diameter: 2,000 mm • Motorized auxiliary drive • Pneumatic disc brake • Hydraulic expansion via sliding wedges • Back support disc and 3 pcs. detachable guide arms at front • Hydraulically operated and driven hold-down roller, lateral adjustment via handwheel • Loading saddle (stationary, decoiler moves hydraulically), lift height 770 mm with 4 pcs. limiting rods Straightening machine Type: RMBMZ 50.600 UF Strip width: 40 - 600 mm Strip thickness: 0.5 – 4.0 mm Straightenable cross-section: 1,200 mm² Number of rollers: 9 pcs. Straightening roller diameter: 50 mm Number of feed rollers: 2 pcs. Feed roller diameter: 100 mm Speed: 3 - 25 m/min Design features: • Rollers hardened, ground and hard-chrome plated • Drive of lower straightening rollers and feed rollers by gear transmission • Motorized adjustment of roller stand via motors, setting accuracy 1/100 mm, values can be saved • Upper rollers can be lifted by 100mm • Feed roller pneumatically liftable • Lateral strip guide at inlet with handwheel and leadscrew • Exit roller basket and loop bridge • Loop control by ultrasonic sensor • Infeed assist, hydraulically operated, consisting of table with extendable tongue and upper bending roller Roll feed Strip width: max. 600 mm Design features: • Rollers hardened, ground and chrome plated • Driven by gear motor • Upper roller can be hydraulically lifted • Height adjustment hydraulic • Lateral strip guide at the infeed with handwheel • Roller basket Further features: • Pneumatically swiveling loop bridge between straightening machine and feeder • Safety fence around the complete system Cgjdpfxjv T Anlj Agqjw • Decoiler and straightener mounted on a common base frame • Various spare rollers for the straightener The complete system is still powered on and can be inspected at the seller's site!!

Stanje: rabljeno, Leto izdelave: 1983, Pritisk 100 t Izravnava 375 mm Hod 20-125 mm Število hodov 60 hodov/min Regulacija bata 80 mm Delovna površina mize 920x660 mm Površina bata 700x450 mm Prebojna odprtina v mizi Ø90 mm Oznaka v batu Ø50 mm Codpfxexh Swho Agqegw Teža stroja cca 8 t Potrebna površina cca 2100x1500x3300 mm Pnevmatična sklopka-zavorna kombinacija Izravnalni valj bata Motorizirana regulacija bata Hidravlično varovalo pred preobremenitvijo v batu Centralno mazanje z mastjo Sprednji ležaj

Stanje: novo, Leto izdelave: 2025, skupna višina: 3.700 mm, nastavitev hidravličnega cilindra: 150 mm, vgradna višina: 650 mm, višina mize: 854 mm, skupna širina: 2.479 mm, skupna dolžina: 4.186 mm, dolžina mize: 2.000 mm, širina mize: 1.200 mm, širina transportnega traku: 350 mm, stiskalna sila: 250 t, hod: 250 mm, razdalja med stranskimi nosilci: 920 mm, razdalja med stojali: 2.040 mm, skupna masa: 31.000 kg, krmilna napetost: 24 V, Standardised 250 ton stamping press with fixed stroke at an attractive price. Cost-optimised basic configuration without enclosure and safety gates, intended for use in a soundproof cabin. Optional accessories available, such as safety gates/enclosure, press force measurement, tool change/clamping system, etc. For technical specifications and offered accessories, please refer to the PDF documents. Delivery time: 6 months. Csdpfx Agswb Dh Ioqegw