Priklopnik sedeža z delovno ploščadjo

FAYMONVILLE MAX Trailer MAX210 Telesattel

Stanje: novo, skupna masa: 48.000 kg, največja dovoljena obremenitev: 38.400 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available on request. Loading Platform: * Extensible loading platform with pneumatically operated locking system * Platform surface with approx. 30 mm thick wooden planks * 7 pairs of foldable lashing rings (LC 5,000 daN) * 3 pairs of foldable lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) Landing Leg: * JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Tyres: * Tyres 385/65 R 22.5 Gbjdpfx Ajxl Nf Doh Dou Axle: * BPW axles and suspension, all axles force-steered by hydro-mechanical system * Equipped with disc brakes * Technical axle load: 10,000 kg (ET 0) * Air suspension with lift and lower valve Brake System: * WABCO brake system in line with EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Paintwork: * High-quality two-component (2K) topcoat, single colour in RAL 3002 Carmine Red Accessories: * Remote steering front and rear via cable remote control with push buttons, including axle tracking control. (no installation in the tractor unit) * Electro-hydraulic power unit * 4 wheel chocks with holders on the front wall * 2-inch king pin * Galvanised connection panel at the front with yellow-red air couplings * Bracket for a rotating beacon at the rear of the trailer * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes on the outside frame of the loading platform * 1 spare wheel holder under the platform, right-hand side in direction of travel (without spare wheel) * Load pressure gauge for axle load determination including load diagram Including Special Equipment: * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks on the platform, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; when extended an additional locking point is provided for a 45' container * 4 pairs of crosswise stake pocket strips mounted in the platform, for approx. 100 x 50 mm plug-in stakes * Storage bracket for up to 9 pairs of plug-in stakes bolted to the inside of the front wall * Climbing ladder mounted on both left and right sides in the direction of travel * 1 INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted under the platform, front left * Additional INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted under the platform, left side * Platform deck with approx. 30 mm thick wooden floor, framed with omega sections * Lifting axle on the front axle with control via TEBS E * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * HRM metalizing (High Resistance Metallisation)

Stanje: rabljeno, skupna masa: 48.000 kg, največja dovoljena obremenitev: 38.080 kg, konfiguracija osi: 3 osi, prva registracija: 02/2025, naslednji pregled (TÜV): 02/2026, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpts from the equipment details. Full specification available upon request. Cargo Area * Extendable cargo area equipped with pneumatically-operated locking mechanism * Loading platform with approximately 30 mm thick wooden floor encased in omega profiles * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tension straps (LC 2,000 daN) Landing Legs: * JOST mechanical landing legs with 2-speed gearbox for approximately 24 t lift capacity (approx. 50 t test capacity) Axles * BPW axles and suspension * All axles with hydro-mechanical forced steering * Equipped with disc brakes * Technical axle load: 10,000 kg (ET 0) each * Air suspension with raise and lower valve * Axle tools included Tyres * Tyres 385/65 R 22.5 Brake System * Brake system compliant with EU regulations, EBS-E (2S2M), no connecting lines to the tractor unit Warning Signs * At the gooseneck and rear end panel, holders for warning panels provided, including socket Electrical System * Electrical system compliant with EU regulations * 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection panel with 24N, 24S & 15-pin sockets, connections according to ISO 24N ISO-1185 24S ISO-3731, 15-pin ISO-12098 Steel Construction * Steel structure made from high-strength fine-grained steel * Steel grades S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Gbsdpfxoxf Sifo Ah Deu Paintwork * Premium, durable corrosion protection through 2-component (2K) zinc dust primer on the standard shot-blasted welded frame * High-quality, single-tone 2-component (2K) topcoat in RAL 3002 carmine red * Rims in silver; attachments as per manufacturer's choice * Rear end metallised and painted in RAL 9010 (pure white) Included Accessories * 2-inch king pin * 4 wheel chocks with holders on the front wall * Steering from front and rear via cable remote control with push buttons, axle single-track control (no installation in tractor unit) * Manual and description on USB stick * Electro-hydraulic unit * Yellow-red air couplings on galvanised connection panel at the front * Yellow reflective tape in line with EU regulations on sides, extension, and rear of the trailer * European reflective plates (red-yellow) at the trailer rear * One mudflap at the trailer rear * Holder for a rotating beacon at the trailer rear * 10 pairs of stake pockets (100x50 mm) integrated into the external frame of the cargo area * 1 spare wheel holder under the right-hand side of the platform (in direction of travel) * 80 km/h speed limit stickers on rear and on both sides * Load manometer for determining axle loads, including load chart * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks on the loading platform for 1x20', 2x20', or 1x40' container; an additional locking point provided in the extension for a 45' container * 4 pairs of transverse stake pocket rails mounted in the platform for approx. 100x50 mm stakes * Storage for stakes inside the front wall * Climbing ladder mounted in driving direction left and right * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted at the front left under the cargo area * An additional we...

Stanje: rabljeno, skupna masa: 48.000 kg, največja dovoljena obremenitev: 36.300 kg, konfiguracija osi: 3 osi, prva registracija: 08/2024, naslednji pregled (TÜV): 08/2025, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory with vehicles available immediately or at short notice can be found on our website. Partial list of equipment. Full equipment details available on request. - Load platform in double-extendable design with pneumatically operated locking mechanism - A fixed intermediate table, approx. 250 mm wide, is mounted on the central beam - BPW axles and suspension, all axles hydro-mechanically forced-steered - Air suspension with lifting and lowering valve - Tyres: 385/65 R 22.5 - JOST landing gear (mechanical) with two-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) - Brake system conforming to EU regulations with EBS-E (2S2M) - Disc brakes - 2-inch kingpin - Electro-hydraulic unit - Remote steering from front and rear via cable remote control - 10 pairs of stake pockets for insertable stakes, approx. 100 x 50 mm, in the outer frame of the loading platform Gbodpfxopkx Eae Ah Dsu - Load gauge for determining axle loads, including load chart - One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high - 6 pairs of WADER container pockets in the platform for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is included in the extension for a 45' container - 5 pairs of crosswise stake pocket rails mounted in the loading area - Storage for max. 9 pairs of insertable stakes approx. 100 x 50 mm, inside at the front wall - One INOX toolbox each, approx. 1,200 x 460 x 550 mm, front left and right under the loading platform - Central lubrication system with 2 BEKAMAX (Pico) pumps - 2 LED reversing lights mounted on the rear plate - An acoustic warning signal when reversing - Bumper protection left and right on the rear traverse - 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear - HRM Metallisation (High Resistance Metallisation) - Single colour paintwork in RAL 3002 carmine red

Stanje: novo, skupna masa: 48.000 kg, največja dovoljena obremenitev: 34.660 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete stock of immediately and soon available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Loading platform * Double-extendable design with pneumatically operated locking mechanism * 2 pairs of recessed lashing rings (LC 5,000 daN) * 1 pair of recessed lashing rings (LC 10,000 daN) * 7 pairs of fold-out external lashing rings (LC 5,000 daN) * 3 pairs of fold-out external lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing legs * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Tyres Gbodpek Ugacefx Ah Dou * 235/75 R 17.5 3PMSF Axles * BPW axles, hydro-mechanically forced steering * Air suspension with lift and lower valve Brake system * In accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * Made from high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting * Premium and durable corrosion protection for the standard shot-blasted welded frame is ensured by a 2-component (2K) zinc primer * High-quality 2-component (2K) topcoat, single-color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Including accessories * Rear and front remote steering by cable remote control with push buttons, with axle tracking control (without installation in the tractor unit) * Electro-hydraulic power pack * 4 wheel chocks with holder on the front bulkhead * 2-inch king pin * At the galvanized connection bar at the front, yellow and red air couplings * Yellow reflective tape as per EU regulations on the sides, extension, and rear of the trailer * European reflective plates (red-yellow) at the rear of the trailer * One mud flap at the rear of the trailer * Manual and documentation on USB stick * Loading platform with heavy-duty hardwood floor * 10 pairs of stake pockets for plug-in stanchions (100 x 50 mm) in the outer frame of the loading platform * Mounting bracket for a rotating beacon at the rear of the trailer * Galvanized supports under the slope of the loading platform * A mounting bracket for a rotating beacon at the rear of the trailer * Mounting rail for aluminium loading ramps at the rear of the vehicle * 80 km/h speed stickers on the rear and both sides * Load gauge for determining axle loads including load diagram * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection for the pumps * Spiral cable to power the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250 A) between trailer and tractor unit with plug connection (NATO-NATO) * Anti-slip sand layer painted on central beam * 6 pairs of WADER container pockets in the loading floor, for 1 x 20' container, 2 x 20' containers or 1 x 40' container, additional locking point in the extension section for one 45' container * 5 crosswise stake pocket bars mounted in the loading floor for plug-in stanchions 100 x 50 mm * Space for up to 9 pairs of plug-in stanchions ca. 100x50 mm, inside front bulkhead * One INOX toolbox, approx. 1,500 x 390 x 810 mm, under the loading platform on both left and right in the direction of travel * Four warning signs, extendable b