Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE MAX Trailer MAX110 Semi-Tieflader

Stanje: novo, skupna masa: 50.960 kg, največja dovoljena obremenitev: 37.680 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our entire range of vehicles, including immediately and short-term available units, on our website. Excerpt from the specification. Full specification available on request. Gooseneck * With approx. 30 mm thick hardwood flooring; gooseneck in straight design at the rear * 3 pairs of lashing rings (LC 5,000 daN) Loading Platform * Extendable version * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading deck for attaching tension belts (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing Legs * JOST mechanical landing legs with 2-speed gearbox for lifting capacity approx. 24 t (test load approx. 50 t) Tyres * 205/65 R 17.5 Axles * BPW axles and suspension * 1st axle rigid, remaining axles hydro-mechanically forced-steered * Air suspension with lift and lower valve Brake System * In accordance with EU regulations, with EBS-E (4S3M), no interconnection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium and durable corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc-rich primer * High-quality two-component (2K) topcoat, single-colour RAL 3002 carmine red * Wheels painted silver Included Accessories * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanised front connection strip * 4 chocks with holders mounted on the front wall * Spare wheel holder in front of front wall * Electro-hydraulic unit * Remote rear- and front axle steering via cable remote control with push buttons, includes single-track monitoring for axles (no installation in the tractor unit required) * European reflector boards (red-yellow) at rear of trailer * Yellow reflective tape complying with EU regulations on the sides, extension and rear * On gooseneck and rear plate—left and right—each with holder for warning boards including connector * Mount for rotating beacon at the rear of the trailer * Galvanized folding supports below the bevel of the loading platform * Axle load pressure gauge including axle-load diagram Crjdpfx Ajv Etx Eegtjh * 7 pairs of WADER container pockets for: 1x 20' or 1x 40' container on the platform, 1x 40' container above the gooseneck, or 2x 20' containers * Support bracket with 1 pair of WADER container pockets, kingpin load approx. 20,000 kg * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm at the outer frame of the load platform * Galvanized extensions, extendable by approx. 230 mm per side * Movable hook-in rails for aluminium drive-on ramps at the rear of the vehicle * 1 pair of recessed lashing rings along the central beam at the rear of the load platform (LC 10,000 daN) * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 and removable guard for the pump * 2 LED reversing lights mounted at the rear * Acoustic reverse warning signal * HRM metallisation (High Resistance Metallisation)

Stanje: novo, skupna masa: 63.000 kg, največja dovoljena obremenitev: 48.305 kg, konfiguracija osi: 3 osi, Oprema: ABS, Our complete stock of vehicles, including those available immediately and at short notice, can be found on our website. Cjdpfx Aow Tpruegterh Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with double extension, featuring rear taper approx. 500 mm x 8° * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 4 pairs of outward folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate platform approx. 250 mm * Cut-outs in the outer frame of the loading area for hanging tension straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, with tread plate flooring over the axles Axles: * BPW axles, hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift/lower valve * Axle tools Tyres: * Tyres 245/70 R 17.5 3PMSF, load index (146/146 F) * Make at our discretion * TPMS tyre pressure monitoring system according to ECE R 141 * Data transmission to the tractor unit takes place via the standardized EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to accept and display this data Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Brake system: * Brake system conforming to EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Steel structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot blasted after welding using a wheel blasting unit * Second blasting process with corundum for optimum adhesion of the coating system * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL system 841GL * Rims in silver * Rear section metallized and painted in RAL 9010 (Pure White) * Metallic paint not available * Paint system tested in salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Including the following additional equipment: * 2 inch king pin * One galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with holders on the front wall * One spare wheel holder in front of the front wall * Electro-hydraulic power unit * Remote steering from front and rear via cable remote control with push buttons, including axle alignment control (without installation in tractor unit) * On the gooseneck, aluminum drop sides and tailboard, plug-in type, approx. 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable (overall body length approx. 2,560 mm) * One galvanized toolbox integrated into the beveled gooseneck * 4 pairs of

Stanje: novo, skupna masa: 48.000 kg, največja dovoljena obremenitev: 33.865 kg, konfiguracija osi: 3 osi, Oprema: ABS, Our complete vehicle inventory with immediately and soon available vehicles can be found on our website. Excerpt from the equipment. Full specification available upon request. Gooseneck * Gooseneck with chamfered front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood floor approx. 30 mm thick Loading Area * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood floor approx. 48 mm thick, chequered plate overlay above axles * Cut-outs in the loading area outer frame for attaching tension belts (LC 2,000 daN) Axles * BPW axles and suspension, all axles hydro-mechanically steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tools Tyres: * 245/70 R 17.5, load index (146/146 F) * Make of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox, lifting capacity approx. 24 t (approx. 50 t tested capacity) Brake system: * Brake system according to EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Paint finish: First class and durable corrosion protection * High-quality two-component (2K) single-colour top coat in RAL 3002 carmine red. * Rear section metallised and painted in RAL 9010 (pure white) Steel construction: Steel structure made of high-strength fine-grained steels. * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system according to EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front terminal strip with 24N, 24S & 15-pin sockets, connection as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Hot-dip galvanised steel bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanised front terminal strip * Spare wheel carrier in front of the bulkhead * Electro-hydraulic power unit * Remote steering front and rear via cable remote control with push buttons, includes axle tracking control (without installation in tractor unit) * Recess at the rear of the gooseneck for aluminium approach ramps * Anchor rail for aluminium approach ramps at the rear of the vehicle * Galvanised folding supports under the loading area rear chamfer * Aluminium drop sides and rear board on the gooseneck, plug-in, approx. 2,440 x 400 mm (L x H) * Rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) * One galvanised toolbox integrated in the chamfered gooseneck * 4 pairs of WADER container locks in the loading area for a 20', 2x 20', 40' or 45' container * 8 pairs of stake pockets for plug-in stanchions approx. 100 x 50 mm in the loading area outer frame * Galvanised extensions, extendable by approx. 230 mm per side * Sliding anchor rails for aluminium approach ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear Csdpfxjw Tprzo Agtsrh * Central lubrication system with 2 BEKAMAX (Pico) pumps, using standard NLGI-2 grease and removable pump protection * 2 LED reversing lights mounted on the rear panel * HRM metallisation (High Resistance Metallisation), complete steel structure shot-peened to SA2.5–SA3, then wit

Stanje: novo, skupna masa: 48.000 kg, največja dovoljena obremenitev: 33.800 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete stock of vehicles, including immediately and short-term available vehicles, can be found on our website. Excerpt from the equipment. Full equipment list available upon request. Gooseneck: Codpfx Agjwvzhbjtjrh * Gooseneck with beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood floor covering approx. 30 mm thick Loading Platform: * Loading platform with double extension and rear bevel approx. 500 mm x 8° * 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Cutouts in the outer frame of the platform for attaching tensioning straps (LC 2,000 daN) * Hardwood floor covering approx. 48 mm thick, checker plate over axles Axles: * BPW axles and suspension * All axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * 245/70 R 17.5 3PMSF, load index (146/146 F) Landing Legs: * JOST landing legs (mechanical), two-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Braking System: * Braking system according to EU regulations with EBS-E (2S2M) Paintwork: * Superior and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a two-component (2K) zinc dust primer * High-quality single-colour two-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 pure white Steel Construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Including the following additional equipment: * 2" kingpin * One galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized terminal strip at the front * 4 wheel chocks with holders on the front wall * Spare wheel holder in front of the front wall * Electro-hydraulic unit * Remote-steering front and rear via cable remote control with pushbuttons, with axle single-track monitoring (without installation in the tractor unit) * Recess at the rear of the gooseneck for aluminum drive-on ramps * European reflective signs (red-yellow) at the rear of the trailer * Yellow reflective tape as per EU regulations on the sides, on the extension, and at the rear of the trailer * Bracket for warning plates with socket on the gooseneck and on the rear panel left and right * Bracket for a rotating beacon at the rear of the trailer * Galvanized folding supports under the rear slope of the loading platform * Mud flap at the rear of the trailer * User manual and documentation on USB stick * 80 km/h speed sticker on the rear and on both sides * Load pressure gauge for determining axle loads including load chart * On the gooseneck, aluminum side and rear boards, plug-in, approx. 2,440 x 400 mm (L x H). The rear galvanized stake pockets are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 4 pairs of WADER container pockets in the platform for one 20', 2x 20', 40', or one 45' container * 8 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading platform * Galvanized extendable widenings by approx. 230 mm per side * Movable hanging rails for aluminum drive-on ramps at the rear of the