Izmetalnik z lopatico za sortirni trak

DIMTER

Stanje: rabljeno, Leto izdelave: 2001, Wood processing dimensions: Infeed lengths min/max: 500 - 6500 mm Full optimization up to max: 1500 mm Infeed widths min/max: 40 - 300 mm Infeed thicknesses min/max: 15 - 120 mm Max. wood cross-sections: 300 x 40 mm or 200 x 120 mm Fixed lengths after saw min: 510 – 2800 mm Special application: Cutting blocks, min/max length: 100 – 200 mm (Note: Multiple block lengths during sorting; blocks are conveyed to the end of the sorting line and fall into customer-supplied mesh boxes) Cutting/trim tolerance: +/- 0.8 – 1.5 mm (depending on timber quality with minimal resin content and uniform surface. Tolerance up to 1 m fixed length; maximum tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm Wood curvature in all directions: max. 10 mm per meter length Wood species: Softwood or hardwood System performance: Feed speed, steplessly adjustable up to max. 230 m/min Cutting cycle: 0.6 – 1 s To determine actual daily output, an efficiency factor dependent on the customer’s production conditions must be applied. Working height infeed and saw: 900 mm (to be placed on customer-side platform; saw requires concrete base) Sorting working height: 2000 mm Connection data: Total electrical connection load: approx. 18 kW Operating voltage: 380 Volt / 50 Hz Voltage fluctuations max. 5 % Air consumption: approx. 1200 NL/min Operating pressure: approx. 8 bar Extraction speed: approx. 30 m/s Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B Rbedow Sy T Hjpfx Ad Tst POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge Pos. 2: Support roller without drive, front-facing sheets table for easier loading Pos. 3: Length measuring station with built-in fluorescence camera to detect error markings Pos. 4: Automatic, contactless width measurement Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with integrated waste chute, incl. equipment package for large wood cross-sections Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and system control Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Pos. 6: Outfeed conveyor belt as sorting station with drive unit, length 7500 mm Pos. 7: 2 ejectors mounted on outfeed conveyor Location: Nattheim

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007,

Stanje: zelo dobro (rabljeno), Leto izdelave: 2005, Funkcionalnost: popolnoma funkcionalen, The Weinig Dimter OptiCut 350 is an advanced wood optimizing saw widely used in the timber industry for dimensional cutting with simultaneous material optimization. This machine offers high-precision cutting at high speeds, maximizing raw material utilization and minimizing material waste. Year of manufacture: 2005 Technical condition: very good Technical specifications: 1. Infeed length of elements: - Maximum length: 6,200 mm - Minimum length: 500 mm 2. Element width: - Maximum width: 300 mm - Minimum width: 40 mm 3. Element thickness: - Maximum thickness: 100 mm - Minimum thickness: 15 mm 4. Cutting speed: - Maximum cutting speed: 250–350 cuts per minute - Material feed speed: up to 200 m/min 5. Cutting tool: - Saw blade rpm: approx. 3,000 rpm 6. Control system: - CNC control with advanced PLC for precise process management - Optimization data input for maximizing material utilization and minimizing waste - Touchscreen interface for machine operation and parameter input 7. Optimization system: - Equipped with a defect detection system (manual or automatic defect marking) for excluding defects during cutting - Length optimization function based on production requirements (e.g., waste minimization, maximizing number of elements of specific lengths) 8. Material feeding system: - Automatic element feeding system - Integrated conveyors and transport systems for efficient material flow through the machine Rbjdpfsv Dm U Rox Ad Tot 9. Waste management: - Waste removal and sorting system for separating defective wood - Number of ejectors: 9 pcs 10. Cutting accuracy: - High cutting precision, with accuracy up to ±0.5 mm depending on wood parameters and machine settings 11. Power supply: - Standard supply: 400 V, 50 Hz Additional features: - Automatic defect marking: Operator can mark wood defects (e.g., knots, cracks), and the machine automatically optimizes cuts to avoid these sections - Safety: Equipped with advanced safety systems, such as lock sensors and protective covers Application: The Weinig Dimter OptiCut 350 optimizer is ideal for the timber industry, especially in facilities producing structural wood components, furniture elements, or for solid wood processing. Its optimization capabilities significantly increase work efficiency and reduce material losses.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2009, Funkcionalnost: popolnoma funkcionalen, Weinig Grecon ProfiJoint Längs-Keilzinkenanlage Baujahr: 2013 Technischer Zustand: sehr gut Technische Daten: Arbeitsbreite: 40–150 mm Arbeitshöhe: 18–50 mm Arbeitslänge: 6100 mm Fräsaggregat: Einlaufmateriallänge: 150–700 mm Materialbreite: 40–150 mm Materialstärke: 18–50 mm Rbedpfx Adeyf N Sls Tet Verbindungsarten: horizontale und vertikale Keilzinkenverbindungen Frässpindelleistung: 18 kW Vorschneidmesser Grecon PJ7/6100 hydraulische Stirnseitepresse: Maximale Fertigteil-Länge: 6100 mm Sägendurchmesser: 350 mm Schnittaggregatsleistung: 2,2 kW Die Maschine wurde 2022 komplett überholt und modifiziert und arbeitet im Automatikbetrieb. Für die Bedienung wird nur eine Person benötigt. Gegen Aufpreis sind Montage, Inbetriebnahme und Schulung möglich.

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2022, obratovalne ure: 500 h, Funkcionalnost: popolnoma funkcionalen, Drying Paternoster for Finger-Jointed Boards Consisting of: - Transfer chain after finger jointing press, foldable Rbsdpfx Adowclkyj Tst - Drying paternoster approx. 7 m, suitable for board lengths up to 6 m - Cut-off and zeroing saw - Conveyor belt for residual wood disposal - Stacking system - Batten magazine is not for sale - Package cross conveyor The machine is in very good condition, very little operating time. The machine is still assembled but immediately available.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2013, Funkcionalnost: popolnoma funkcionalen, Linija za vzdolžno spajanje lesa Weinig Grecon ProfiJoint Leto izdelave: 2013 Tehnično stanje: zelo dobro Rjdpfx Asyf N Itod Tebt Tehnični podatki: Delovna širina: 40–150 mm Delovna višina: 18–50 mm Delovna dolžina: 6100 mm Rezkar: Dolžina vhodnega materiala: 150–700 mm Širina materiala: 40–150 mm Debelina materiala: 18–50 mm Možnosti spajanja: vodoravni in navpični spoji Moč rezkalne vretena: 15 kW Čelna hidravlična stiskalnica Grecon PJ7/6100: Največja dolžina končnega elementa: 6100 mm Premer žage: 350 mm Moč rezalne enote: 2,2 kW Ob doplačilu možnost montaže, zagona in usposabljanja za upravljanje.

Stanje: rabljeno, Leto izdelave: 1999, Funkcionalnost: popolnoma funkcionalen, montažni premer: 50 mm, vrsta vhodnega toka: trifazni, premer orodja: 50 mm, dolžina orodja: 330 mm, vhodna frekvenca: 50 Hz, Naprava za prednastavitev orodja WEINIG Opticontrol Rbedpfjxwnvrox Ad Tet Premer krožnega gibanja: 0 - 300 mm Dolžina orodja: 0 - 330 mm Premer stebla: 50 mm

Stanje: pripravljen za uporabo (rabljen), De-stacking by layers for layer singulation Stack slat separator with conveyor belt Layer transport to layer buffer Layer buffer with singulation before the feeding unit Rjdpeuzht Tjfx Ad Tobt Layer patterns for the two separated timbers including transfer conveyors, for example to the stacking machine

Stanje: rabljeno, Rezkalno vreteno Vretena za rezkalnike za zatiče Stroj za rezkanje žlebičev z lastovičjim repom različne dolžine Rsdpfx Aeqwgrpjd Tjbt različni modeli na zalogi v spletni trgovini www jöma Proizvajalci: GreCon, Sauter, DIMTER

Leto izdelave: 2005, Stanje: pripravljen za uporabo (rabljen), Ta WEINIG Unimat 500 je bila izdelana leta 2005. Robustni lesnoobdelovalni stroj z delovnim območjem 230 x 120 mm in petimi vreteni omogoča učinkovito obdelavo z nastavljivo podajalno hitrostjo od 4 do 30 m/min. Moč vretena znaša 4 kW za vstopni in izstopni vreteno ter 7,5 kW za desno/levo in zgornje vreteno. Izkoristite priložnost za nakup tega WEINIG Unimat 500 lesnoobdelovalnega stroja. Za dodatne informacije o stroju nas kontaktirajte. Dodatna oprema • Približno 70 rezilnih glav Z4 • Več sto novih polizdelkov rezil z nazobčanim hrbtom Prednosti stroja Kvalitativne prednosti stroja Rbodpfx Adsyaihpo Tst • Vodilo za utore in hidravlične matice Tehnične prednosti stroja • Delovno območje (širina x višina): 230 x 120 mm • Število vreten: 5 • Spremenljiva hitrost podajanja: 4–30 m/min • Moč vretena: spodaj (vstop): 4 kW / desno / levo: po 7,5 kW / zgoraj: 7,5 kW / spodaj (izstop): 4 kW

Stanje: rabljeno, Length 2700 mm Width 1100 mm Height 850 ± 150 mm Motor power 0.37 kW Electrical power 0.5 kW Compressed air 6 bar Horizontal impregnation unit 'Pro flow' for individual parts with rinsing circuit. ----- Functional features: Machine for horizontal flooding of individual workpieces. The product is applied by a row of nozzles. Excess product is then blown off by air nozzles. The pump and air nozzles are automatically controlled and only operate when a workpiece passes through. This helps to reduce compressed air consumption. The recirculation mode ensures minimal product consumption. ----- Construction features: Structure Robust steel frame, coated with high-strength, water-soluble paint. Machine body made of hot-sealed, thick polypropylene panels. Four independent chambers for entry, flooding, air-blow, and exit. Horizontal feed of workpieces By means of motor-driven plastic rollers with grooves. Electronic frequency inverter for controlling and varying feed speed. Transmission The machine is fitted with an exclusive system whereby all gear mechanisms are located outside the flooding chamber and are easily accessible for the operator, guaranteeing longer operational life and facilitating maintenance. Moving parts are protected by cover plates and appropriate seals. Recirculation pump Pneumatic double-diaphragm pump with valves, seals, and diaphragms made from nitrile rubber, and a housing made of plastic material (PVDF). Air nozzles A blow-off system is installed in the first chamber to prevent product from escaping. A second blow-off system after the flooding chamber removes excess product from the workpiece. Electrical control panel According to CE, protection class IP 55. Includes inverter for adjusting feed speed. Technical data Length mm 2700 Width mm 1100 Feed speed (min./max.) m/min 3-6 Drive group motor power kW 0.37 Installed electrical power kW 0.5 Distance between entry and exit rollers mm 2520 Working height (adjustable) mm 850 ± 150 Min. length of workpieces to be flooded mm 250 Max. width of workpieces to be flooded mm 300 Max. height of workpieces to be flooded mm 250 Compressed air consumption l/min 2000 Required compressed air pressure bar 6 Equipment and included accessories Rinsing circuit for Pro Flow ----- Price of the above machine: on request! plus packaging and transport Rodpfjnl Nqqsx Ad Tjbt ----- (Technical data according to manufacturer – without guarantee! Illustrations may differ from original. Prices net, plus VAT (domestic))

Leto izdelave: 1997, Stanje: pripravljen za uporabo (rabljen), skupna masa: 10.500 kg, skupna višina: 2.000 mm, This Grecon Dimter FDL-F 205/600/500 was manufactured in 1997. It is designed for woodworking and offers robust performance and reliability, making it ideal for efficiently handling a wide range of woodworking tasks. Please contact us for further information regarding this machine. Rbsdpfjyabawex Ad Tot Additional Equipment • Press (Front Press): Pressing force 6–12 t and power consumption of 52 kW • Compressed air consumption: 350 NL/min for the milling machine, 500 NL/min for the press • Suction volume: 10,600 m³/h • The machine ensures fast transport cycles with precise alignment • Includes a hydraulic pressing system for continuous jointing • Equipped with integrated dust extraction and extraction system Machine Advantages Technical Machine Advantages • Feeding & transport: conveyor belt with a speed of 75 m/min and a power output of 11 kW / feeding & transport: conveyor belt with a speed of 75 m/min and a power output of 11 kW / entry station maximum feed speed: 120 m/min, power consumption 22 kW • Workpiece dimensions: length: 150–2000 mm / width: 50–205 mm / height: 35–50 mm 60 / final length: 3000–00 mm • Milling machine: turbo milling combination with a power consumption of 63 kW / milling spindle motor: 22 kW, 3000 rpm / cutting motor: 55 kW, 2880 rpm Dimensions Machine depth 18,500 mm

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Optimizirka Grecon Dimter OptiCut 304R Rodpjx Up Nqsfx Ad Tebt Vhodna dolžina lesa min. 500 mm pri nalaganju na podporno mizo Vhodna dolžina lesa min. 900 mm pri nalaganju na prečni verižni transporter Maksimalna dolžina lesa: 6300 mm Širina lesa min./maks.: 40–200 mm Debelina lesa min./maks.: 15–80 mm Maksimalni preseki lesa: 200×25 mm, 170×50 mm, 80×80 mm, 140×60 mm Premer žaginega lista: 400 x 30 mm Število obratov žaginega lista: 4200 obr./min Maksimalni pomik: 230 m/min Načini rezanja: - rezanje na stalno dolžino - optimizacija dolžine desk za maksimalni izkoristek - odstranjevanje napak v lesu z označevanjem defektov s kredo

Stanje: pripravljen za uporabo (rabljen), Panel length: 3200 mm, panel width: 1000 mm, max. workpiece thickness: 38 mm, min. infeed length: 500 mm. Rbedpsm Habdofx Ad Tet

Leto izdelave: 1998, Stanje: pripravljen za uporabo (rabljen), moč vretenovega motorja: 11.000 W, največja hitrost vretena: 6.000 obr/min, This Weinig Unicontrol 10-5 was manufactured in 1998. It is a robust, used window production machine with a working width of 40–220 mm and a motor power of up to 15 kW for various machining units. The machine features advanced options such as a synchronization device, electronic height adjustment, and an automatic turning system to enable efficient single-operator workflow. If you’re looking for a high-quality milling machine, we recommend considering the Weinig Unicontrol 10-5, which we have available for sale. Please contact us for further information. • Capacity • Working width: 40–220 mm • Working height (longitudinal processing): 40–100 mm • Working height (cross processing): 40–100 mm (grain height 80 mm) • Workpiece length (longitudinal): min. 220 mm + 2 x tenon length • Workpiece length (cross): min. 275 mm + 1 x tenon length at 320 mm tool diameter • Feed unit (cross processing) • Motor power: 0.3 kW • Feed speed: 3–25 m/min • Workpiece clamping: 2 hold-down clamps • Length stop: with scale and magnifier for measurement of sash or frame external dimensions • Counter: pneumatically indexed, 4 positions (not suitable for Studio windows), up to a maximum timber height of 80 mm • Double workpiece package: single or double part feed system, with cross separation and retention system • 1st workpiece (lying against stop) wood width: 55–90 mm • 2nd workpiece wood width: 130 mm • Feed unit (longitudinal processing) • Motor power: 2.2 kW • Feed speed: 4–18 m/min (continuously adjustable via frequency inverter) • Feed roller spacing: 100/120 mm • Feed roller width: 30/50 mm • Feed roller diameter: 95 mm • Processing units • Cross-cut saw • Motor power: 3 kW • Spindle diameter: 40 mm • Spindle speed: 2800 rpm • Tool stroke: max. 400 mm • Axial adjustment: pneumatic against four-position turret • 1st spindle with tenon and slot • Motor power: 11 kW • Spindle diameter: 50 mm • Spindle speed: 3250 rpm • Tool stroke: max. 320 mm • Tool clamping length: 320 mm • Axial adjustment range: 240 mm • Number of tool positions: 4 x 80 mm • Axial adjustment: hydraulic • 1st profiling spindle • Motor power: 11 kW • Spindle diameter: 50 mm • Spindle speed: 6000 rpm • Tool diameter: max. 232 mm • Tool reference circle: 130–140 mm • Tool clamping length: 320 mm • Axial/radial adjustment range: 240/80 mm • Number of tool positions: 4 x 80 mm • Axial adjustment: hydraulic • 2nd profiling spindle • Motor power: 11 kW • Spindle diameter: 50 mm • Spindle speed: 6000 rpm • Tool diameter: max. 232 mm • Tool reference circle: 130–140 mm • Tool clamping length: 320 mm • Axial/radial adjustment range: 240/80 mm • Number of tool positions: 4 x 80 mm • Axial adjustment: hydraulic • Mechanical spindle brakes • For profiling spindle(s) Rodpsx S Sk Eofx Ad Tjbt • For cross-cut saw and profiling/cutting units • Profile milling unit (horizontal, top; in front of last profiling spindle) • Radially switched: 2 positions • Axially switched: 2 positions • Motor power: 3 kW • Spindle diameter: 40 mm • Spindle speed: 5850 rpm • Tool stroke: 130 mm • Tool clamping length: 40 mm • Axial adjustment range: 52 mm • Radial adjustment range: 125 mm • Profile milling unit (vertical, right; at end of machine) • Radially indexed: 2 positions • Axially indexed: 2 positions • Motor power: 3 kW • Spindle diameter: 40 mm • Spindle speed: 5850 rpm • Tool stroke: 210 mm • Tool clamping length: 160 mm