Mlin za rezanje plastike CMG N4090AT 30kW

CMG N4090AT Rotor 900mm

Stanje: rabljeno, Leto izdelave: 2006, Ponudba za prodajo: Mlin za rezanje plastike Bjdpfxex Itzde Abhelc Visoko zmogljiv industrijski rezalni mlin, zasnovan za mletje plastike in plastičnih folij. Sprednje podajanje v kombinaciji z dvižnim zalogovnikom zagotavlja udobno in varno upravljanje. Masiven rotor z natančnim nožnim sistemom in sitom omogoča učinkovito in enakomerno rezanje. Idealno za reciklažo in proizvodne linije. Tehnične specifikacije: Moč motorja: 35 kW Zmogljivost: do 600 kg/h Premer rotorja: 420 mm Hitrost rotorja: 430 vrt/min Vhodna odprtina: 915 × 502 mm Največja širina vhodne folije: 915 mm Rotacijski noži: 3 + 3 Fiksni noži: 2 + 2 Premer lukenj sita: 8 mm Pogonski sistem: 5 klinastih jermenov Podajanje materiala: sprednje podajanje Zalogovnik: dvižen, ročna regulacija nagiba Skupna teža stroja: 1900 kg Robustna zasnova, visoka učinkovitost, pripravljen za industrijsko uporabo.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, obratovalne ure: 21.676 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 78 t, širina odprtine za polnjenje: 750 mm, dolžina polnilne odprtine: 1.500 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 600 kg, skupna masa: 25.000 kg, transportna višina: 3.000 mm, kapaciteta rezervoarja za olje: 1.000 l, moč: 55 kW (74,78 KM), lastna masa: 25.000 kg, volumenski pretok: 930 m³/h, obratovalni tlak: 250 letvica, Good day, We are pleased to offer you, on a non-binding basis, a used baler manufactured by Presona AB, model LP 80 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We do not assume any liability for their accuracy or completeness. Manufacturer: Presona AB, Sweden Model: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours (as of November 2024) Press force (main press): 78 t Specific press force: 95 N/cm² Pre-compression flap force: 28 t Bedpfxovgrh Uj Abholc Feed opening dimensions: 1,500 x 1,100 mm Fill volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 1,000 L Baler dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (baler) approx. 25 t Note: The machine was used in a recycling operation for compacting paper, cardboard, and films. The baler is in good condition, will remain in operation until January 2025, and can be inspected by prior arrangement. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Stanje: rabljeno, Leto izdelave: 2006, Ponudba za prodajo: Mlin za rezanje plastike Visoko zmogljiv industrijski rezalni mlin, zasnovan za mletje plastike in plastičnih folij. Sprednje podajanje v kombinaciji z dvižnim zalogovnikom zagotavlja udobno in varno upravljanje. Masiven rotor z natančnim nožnim sistemom in sitom omogoča učinkovito in enakomerno rezanje. Idealno za reciklažo in proizvodne linije. Tehnične specifikacije: Moč motorja: 35 kW Zmogljivost: do 600 kg/h Premer rotorja: 420 mm Hitrost rotorja: 430 vrt/min Vhodna odprtina: 915 × 502 mm Največja širina vhodne folije: 915 mm Rotacijski noži: 3 + 3 Bedpfx Aex Itx Aebhjlc Fiksni noži: 2 + 2 Premer lukenj sita: 8 mm Pogonski sistem: 5 klinastih jermenov Podajanje materiala: sprednje podajanje Zalogovnik: dvižen, ročna regulacija nagiba Skupna teža stroja: 1900 kg Robustna zasnova, visoka učinkovitost, pripravljen za industrijsko uporabo.

Leto izdelave: 2003, obratovalne ure: 43.000 h, Stanje: potreben popravila (rabljeno), številka stroja/vozila: HBC 140 2x75kW 2003 (W230-005), Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Kanaalbalenpers (2x75kW). Pers: Gewicht: 47.100 kg Bouwjaar: 2003 Hardox bodemvloerplaat uitsluitend Kunststof ventiel Anti-ratten bekabeling Draaiuren: 43.000 Deze pers kan tevens volledig gereviseerd worden verkocht volgens de 'Bollegraaf OEM Certified Refurbishment standards'. Hierbij geldt een garantie van 2 jaar. Neem contact met ons op voor meer informatie of een vrijblijvende offerte. Algemene principes van revisie Reiniging & demontage Voordat de revisie daadwerkelijk plaatsvindt, wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Bjdokcgynepfx Abhjlc Toleranties Na demontage worden de toleranties van alle stalen componenten nagemeten en waar nodig opnieuw gelast. Dit geldt in elk geval voor de volgende onderdelen: • Aanpersplaat (ram) • Frame • Kanaal • Voorpersklep Na demontage en inspectie wordt de ram opgelegd en voorzien van nieuwe ramwielen. De beschermroosters en de voorpersklep worden waar nodig uitgedeukt en gerepareerd. Overspuiten Na het meten van de toleranties en eventuele herstel- en laswerkzaamheden, worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydrauliekleidingen & slangen worden vervangen. De hydraulische componenten worden voorzien van nieuwe pakkingen. De hydrauliekolie wordt vervangen. Bekabeling: Alle bekabeling wordt gecontroleerd en waar nodig vervangen. Alle aansluitdozen worden vervangen en gemonteerd op goed toegankelijke locaties. Slijtdelen: Alle slijtdelen worden vervangen. De pennen en assen van de cilinders en het kanaal worden vernieuwd. Alle slijtdelen van beide naaldinstallaties en knopers worden vernieuwd. Cilinders: De cilinders worden opnieuw verpakt en, indien nodig, voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC-kast: De schakelkast wordt gecontroleerd en gereinigd. Waar nodig worden elektronische componenten vernieuwd. De PLC en HMI (bedieninterface) worden vervangen door de nieuwste Schneider M340-versie inclusief de nieuwste software.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: HBC 140 2x75kW 2001 (210-008-01), stiskalna sila: 155 t, teža bale: 1.500 kg, pritisk: 250 letvica, moč: 150 kW (203,94 KM), leto zadnje generalne obnove: 2024, Oprema: dokumentacija / priročnik, Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en transportband: Bollegraaf HBC140s Kanaalbalenpers (2x75kW). Bjdetvau Aepfx Abholc Pers: Gewicht: 47.100 kg Bouwjaar: 2001 Variabele kanaaldrukregeling Kunststof ventiel Anti-ratten bekabeling Draaiuren: 0 na volledige revisie Deze pers wordt volledig gereviseerd verkocht volgens de 'Bollegraaf OEM Certified Refurbishment standards', inclusief 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene principes van revisie Reiniging & demontage Voordat de feitelijke revisie plaatsvindt, wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Toleranties Na demontage worden de toleranties van alle stalen componenten gemeten en opnieuw gelast waar nodig. Dit geldt ten minste voor de volgende onderdelen: • Persplunjer, • Frame, • Perskanaal, • Voorpersklep Na demontage en inspectie wordt de persplunjer opnieuw opgelast en voorzien van nieuwe plunjerwielen. De beschermroosters en de voorpersklep worden deukvrij gemaakt en waar nodig gerepareerd. Opnieuw gespoten Na het meten van de toleranties en alle benodigde reparatie- en laswerkzaamheden, worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydrauliekleidingen en -slangen worden vervangen. De hydraulische componenten worden opnieuw verpakt. De hydrauliekolie wordt vervangen. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vervangen. Alle aansluitkasten worden vervangen en teruggeplaatst op goed toegankelijke plekken. Slijtdelen: Alle slijtdelen worden vervangen. De pennen en assen van de cilinders en het perskanaal worden vernieuwd. Alle slijtdelen van beide naaldinstallaties en knopers worden vervangen door nieuwe. Cilinders: De cilinders worden opnieuw verpakt en indien nodig voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC Kast De schakelkast wordt gecontroleerd en schoongemaakt. Indien nodig worden elektronische componenten vervangen door nieuwe. De PLC en HMI (mens-machine-interface) worden vervangen door de nieuwste Schneider M340-versie, inclusief de meest recente software.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2014, obratovalne ure: 37.656 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 85 t, širina odprtine za polnjenje: 1.500 mm, dolžina polnilne odprtine: 1.100 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 650 kg, skupna masa: 25.000 kg, kapaciteta rezervoarja za olje: 1.000 l, leto zadnje generalne obnove: 2024, volumenski pretok: 410 m³/h, transportna širina: 2.400 mm, transportna dolžina: 9.300 mm, Good day, We hereby offer you, without obligation, a used baler from the manufacturer Presona AB, type LP 85 VH1. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we cannot assume any liability for the accuracy and completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours (as of March 25) Main press force: 85 t Specific press force: 100 N/cm² Pre-press door force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Bjdpov T I Evjfx Abhelc Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Machine weight press: approx. 25 t Note: This machine was used in a recycling facility for compacting paper, cardboard, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have already been replaced in the last 3 years. The machine has been serviced regularly. We would be pleased if this press is of interest to you. Your Service Team, Mertens & Frowein GmbH

Stanje: rabljeno, skupna masa: 1.500 kg, premer rotorja: 252 mm, skupna dolžina: 1.800 mm, skupna višina: 2.000 mm, skupna širina: 1.200 mm, širina rotorja: 600 mm, moč: 18,5 kW (25,15 KM), največja hitrost vrtenja: 90 obr/min, širina odprtine za polnjenje: 600 mm, dolžina polnilne odprtine: 800 mm, No. 3255 Single-Shaft Shredder / WEIMA WL 4 Used machine Quiet-running and slow-running V-Rotor system Main drive motor power: 18.5 kW Rotor diameter: 252 mm Rotor width: approx. 600 mm Rotor speed: approx. 90 rpm Hopper volume: 0.6 m³ Feed opening: 800 x 600 mm (L x W) Reversible knives, concave ground Automatic / manual operation Screen perforation: 15 mm Extraction nozzle: 160 mm Transport dimensions: approx. 1800 x 1200 x 2000 mm (L x W x H) Weight: approx. 1,500 kg Sale on behalf of customer, ex location near 73430 Aalen, without disassembly, transport, or installation Disassembly, loading, and transport by us optionally possible Specifications and price subject to change without notice To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sale as is Technical data, description of condition, year of manufacture, and scope of delivery as per manufacturer’s brochure or previous owner, no guarantee Bjdpox Hhk Rjfx Abhslc Subject to prior sale No warranty on used machines, sale as inspected Pictures and videos are samples, do not represent the actual scope of delivery Payment terms: Prices plus statutory VAT, payment before collection or shipping Delivery terms: ex location

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 1996, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 170 t, širina odprtine za polnjenje: 1.020 mm, dolžina polnilne odprtine: 1.800 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, skupna masa: 40.000 kg, kapaciteta rezervoarja za olje: 3.000 l, leto zadnje generalne obnove: 2024, For sale is a used baling press system consisting of a chain belt conveyor for under-floor operation, complete with a feed hopper, a hydraulic pre-compactor with agitator, a MACPRESSE 111A baling press, two complete wire tying racks each with 5 wire spool holders (wire not included). Technical data - Press: Manufacturer: MACPRESSE EUROPA S.R.L. Bsdpfx Abou Th D Rohjlc Model: 111A Year of manufacture: 1996, overhauled in 10/2024 Main press force: 170 t Specific press force: 14 kg/cm² Feed chute dimensions: 1,800 x 1,020 mm Filling volume: 2.5 m³ Theoretical throughput: 750 m³/hour Bale dimensions: 1,100 x 1,100 mm, length variable Drive power: 2 x 55 kW Tying: 5-fold horizontal, fully automatic Throughput rates: approx. 30 to 35 t/hour, depending on material Hydraulic tank volume: 3,000 l Transport dimensions (press with new machine feet): 11,700 x 2,300 x 2,900 mm (L x W x H) Machine weight (press): approx. 40 t Remarks: The baling press was partially overhauled in our workshop and fully tested after completion—see our function video for reference. Previously, paper and cardboard from municipal collection were pressed with the system. The operation was reassigned after the contract period ended, so the entire plant is for sale. Details of the overhaul and replaced spare parts can be found in the detailed photo documentation and our offer. The full documentation (manual, CE declaration, electrical/hydraulic diagrams) is available. Inspection by appointment. No liability assumed for technical data or possible errors. Technical data - Conveyor belt: Manufacturer: Wagensfeld B.V. Model: Chain belt conveyor 1700 mm Year of manufacture: 2017 Drive power: 7.5 kW Belt speed: 14 m/minute Feed belt length: 6,900 mm Inclined belt length: 12,885 mm Gooseneck length: 1,747 mm Total length: 21,271 mm Incline: 32° Usable width: 1,644 mm Drive axle height above ground: 5,777 mm Feed belt wall height: 500 mm Inclined belt wall height: 880 mm Steel cleat height: 40 mm Cleat spacing: 1,200 mm Transport dimensions (disassembled): 15,005 x 2,503 x 2,435 mm (L x W x H) Pit dimensions: 11,500 x 2,700 x 1,015 mm (L x W x D) Remarks: The chain belt conveyor, built in 2017, was custom-built and installed to fit the press at its last installation in the Netherlands. The conveyor is in good, ready-to-use condition and has therefore not been overhauled. A layout drawing with pit dimensions is available. Scope of delivery: 1 x Chain belt conveyor, Wagensveld B.V. 1 x Feed hopper with pre-compactor flaps 1 x Agitator 1 x MACPRESSE baling press, type 111A 2 x Wire tying racks with wire spool holders, without wire 1 x Operating manual with CE declaration, electrical and hydraulic wiring diagrams

Stanje: dober (rabljeno), Leto izdelave: 2008, premer rotorja: 368 mm, WEIMA drobilnik Serija HWV 3000 (37 kW) in enovretenski drobilnik WL12 (30 kW) Bjdpfxsx I S Hfe Abhslc Idealno za predhodno drobljenje lesnih odpadkov, kot so palete, sledeno z ločevanjem kovin in nadaljnjim drobljenjem. Prednosti: Dvostopenjski proces: Pred- in naknadno drobljenje za maksimalno učinkovitost. Vsestranska uporaba: Lesni sekanci za ogrevalne sisteme ali briketirne preše. Tiho delovanje. Tehnične podrobnosti – HWV 3000: - Moč: 37 kW - Dimenzije (lijak): 3375 mm širina x 1630 mm višina - Rezila: 58 nožev v dveh vrstah Tehnične podrobnosti – WL12/30: - Moč: 30 kW - Premer gredi: 368 mm - Sito: 15/20 mm Možnosti uporabe - Predelava in recikliranje lesnih odpadkov - Pridobivanje energije z lesnimi sekanci ali briketiranjem

Leto izdelave: 2013, Stanje: rabljeno, Technical Data for Bale Opener Line for RDF, MSW, Paper, Cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Model: BO 4000 Year of Manufacture: 2015 Number of Bales Opened: 674 Operating Time: Only 3 days, exclusively during commissioning of the entire system at new installation Opening Time: approx. 45 seconds per bale Bale Dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Maximum Bale Weight: 2,000 kg System Discharge Height: 1,400 mm Maximum Conveyor Width: 1,200 mm Material to be Opened: RDF/MSW System Availability: 98% Bjdju Tg I Dopfx Abhslc Noise Level of Bale Opening Line: 85 dB(A) Total Connected Load: 37 kW Rated Current: 125 A Operating Display: SIEMENS SIMATIC HMI Touch Control System: SIEMENS S7 ET200S Machine Dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of Supply: - Feed Conveyor 3,500 x 1,200 x 1,400 mm - Infeed Conveyor to Opener 1,500 x 1,200 x 1,400 mm - Bale Opener (gripper with cutter) Special Equipment: - Oil heater in hydraulic oil tank - Control cabinet heater - Oil cooler for hydraulic unit Explanation for Short Operating Time: The complete Cross Wrap bale opener line type BO 4000 was installed in 2015 at a municipal waste incineration plant. The purpose of the installation was to allow municipal waste to be received, baled, wrapped, and stored in case of a plant malfunction or maintenance, until normal operation resumed. After the issue was resolved, all bales would then be opened and the waste fed back into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned and subsequently never used in regular operation. Only during initial commissioning in 2015 were 674 bales opened over three days. The system is in excellent, ready-to-use condition. Due to plant modifications, the installation area is needed for other purposes, and the complete line is therefore offered for sale. Brief Description of the Bale Opening Process: The compressed bales are placed onto the infeed conveyor from the side or rear using a forklift. For opening, the bales must be positioned with the wire or twine binding running horizontally to the conveyor; otherwise, bales must be rotated 90°. The infeed conveyor moves each bale to the cutting unit. The grippers hold the wire or twine strapping firmly. The rotating knife cuts the bale lengthwise. The gripper then returns to its initial position. The opened bale is then conveyed to the discharge chute and drops onto the subsequent conveyor system. Notes: Original price of the complete system was €296,000. Complete documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is available. The system has been dismantled into transportable units, stored, and is available for inspection and loading at short notice. No liability is assumed for the technical specifications or any potential errors.